Filters
total: 1605
filtered: 1486
displaying 1000 best results Help
Search results for: STORAGE TANKS, FOUNDATION SETTLEMENT, SUBSOIL PARAMETERS, SENSITIVITY ANALYSIS
-
A dynamic vehicle-bridge model based on the modal identification results of an existing EN57 train and bridge spans with non-ballasted tracks
PublicationThis paper addresses the methodology of the bridge-vehicle dynamic model definition based on the free response measurements of an existing train and existing bridge spans. In the case of the railway vehicle, the methodology uses the impulse excitations of a single car by means of the wedge method. In the case of the bridge spans, free responses are collected after the passages of trains. The global modal parameters (frequencies...
-
A LUMPED-CIRCUIT MODEL OF CIRCULAR PISTON TRANSDUCER FOR MODELING ITS PERFORMANCE IN DUAL FREQUENCY OPERATING MODES
PublicationThe paper presents novel network equivalent circuit of piezoceramic circular disc transducer that takes into account thickness and ra dial mode of vibrations. The starting point of the analysis is 4-port description of circular disc element representing the solution of wave equation set in radial and thickness directions. Th e approximate solution for harmonic case is represented in the form of 4x4 matrix, which is syn thesized...
-
Comparative Analysis of Text Representation Methods Using Classification
PublicationIn our work, we review and empirically evaluate five different raw methods of text representation that allow automatic processing of Wikipedia articles. The main contribution of the article—evaluation of approaches to text representation for machine learning tasks—indicates that the text representation is fundamental for achieving good categorization results. The analysis of the representation methods creates a baseline that cannot...
-
Damage Detection in the Wind Turbine Blade Using Root Mean Square and Experimental Modal Parameters
PublicationThe paper presents results of an experimental study related to a non-destructive diagnostic technique used for preliminary determination the location and size of delamination in composite coatings of wind turbine blades. The proposed method of damage detection is based on the analysis of the ten first mode shapes of bending vibrations, which correspond to displacements of rotor blades perpendicular to the rotor plane. Modal parameters...
-
High-Efficacy Global Optimization of Antenna Structures by Means of Simplex-Based Predictors
PublicationDesign of modern antenna systems has become highly dependent on computational tools, especially full-wave electromagnetic (EM) simulation models. EM analysis is capable of yielding accurate representation of antenna characteristics at the expense of considerable evaluation time. Consequently, execution of simulation-driven design procedures (optimization, statistical analysis, multi-criterial design) is severely hindered by the...
-
Simulation of the response of base-isolated buildings under earthquake excitations considering soil flexibility
PublicationThe accurate analysis of the seismic response of isolated structures requires the incorporation of the flexibility of supporting soil. However, it is often customary to idealize the soil as rigid during the analysis of such structures. In the present paper, seismic response time history analyses of base-isolated buildings modelled as single degree-of-freedom (SDOF) and multi degree-of-freedom (MDOF) systems with linear and nonlinear...
-
Cost-Efficient Bi-Layer Modeling of Antenna Input Characteristics Using Gradient Kriging Surrogates
PublicationOver the recent years, surrogate modeling has been playing an increasing role in the design of antenna structures. The main incentive is to mitigate the issues related to high cost of electromagnetic (EM)-based procedures. Among the various techniques, approximation surrogates are the most popular ones due to their flexibility and easy access. Notwithstanding, data-driven modeling of antenna characteristics is associated with serious...
-
DESIGN ANALYSIS OF HYBRID GAS TURBINE - FUEL CELL POWER PLANT IN STATIONARY AND MARINE APPLICATIONS
PublicationThe paper concerns design analysis of a hybrid gas turbine power plant with a fuel cell (stack). The aim of this work was to find the most favorable variant of the medium capacity (approximately 50 MW) hybrid system. In the article, computational analysis of two variants of such a system was carried out. The analysis let to calculate capacity, efficiency of both variants and other parameters like flu gas temperature. The paper...
-
Exhaled breath analysis by resistive gas sensors
PublicationBreath analysis has attracted human beings for centuries. It was one of the simplest methods to detect various diseases by using human smell sense only. Advances in technology enable to use more reliable and standardized methods, based on different gas sensing systems. Breath analysis requires the detection of volatile organic compounds (VOCs) of the concentrations below individual ppm (parts per million). Therefore, advanced detection...
-
Fracture Surface Behavior of 34CrNiMo6 High-Strength Steel Bars with Blind Holes under Bending-Torsion Fatigue
PublicationThe present study evaluates the fracture surface response of fatigued 34CrNiMo6 steel bars with transverse blind holes subjected to bending with torsion loading. The analysis of the geometric product specification was performed by means of height parameters Sx, functional volume parameters Vx, and fractal dimension Df. Surface topography measurements were carried out using an optical profilometer with focus variation technology....
-
Influence of artificial thermal ageing on polyester-reinforced and polyvinyl chloride coated AF9032 technical fabric
PublicationThe presented work deals with the thermal ageing evaluation for polyester-reinforced and polyvinyl chloride coated fabrics. The architectural fabric AF9032 was exposed to artificial thermal ageing by subjecting the material samples to temperature levels of 80℃ and 90℃ for up to 12 weeks. The mechanical properties of the aged fabric have been separately described by the identified linear piecewise model (with assumption of the elastic...
-
Identification of Parameters Influencing the Accuracy of the Solution of the Nonlinear Muskingum Equation
PublicationTwo nonlinear versions of the Muskingum equation are considered. The difference between both equations relates to the exponent parameter. In the first version, commonly used in hydrology, this parameter is considered as free, while in the second version, it takes a value resulting from the kinematic wave theory. Consequently, the first version of the equation is dimensionally inconsistent, whereas the proposed second one is consistent. It...
-
Building damage due to structural pounding during earthquakes
PublicationEarthquake-induced pounding between adjacent buildings has been identified as one of the reasons for substantial damage or even total collapse of colliding structures. A major reason leading to interactions in buildings results from the differences in their dynamic parameters and also from insufficient distance between the structures. Although the research on structural pounding has been much advanced, the studies have mainly been...
-
Novel analysis methods of dynamic properties for vehicle pantographs
PublicationTransmission of electrical energy from a catenary system to traction units must be safe and reliable especially for high speed trains. Modern pantographs have to meet these requirements. Pantographs are subjected to several forces acting on their structural elements. These forces come from pantograph drive, inertia forces, aerodynamic effects, vibration of traction units etc. Modern approach to static and dynamic analysis should...
-
Historical carpentry corner log joints—Numerical analysis within stochastic framework
PublicationThe paper presents the results of numerical analysis performed on historical, traditional carpentry corner logjoints of two basic topologies: the short-corner dovetail connection and the saddle notch connection. These types of carpentry joints are commonly used in currently preserved objects of wooden architecture. All connections have been modelled in pinewood, which has been defined in the Finite Element software MSC.Marc/Mentat...
-
Alternative methods for dark fermentation course analysis
PublicationDark fermentation course analysis is crucial, as complexed matrix of gaseous components may be formed and revealed during the process. The paper considers key issues related to the microbiological process in which complex organic substances are transformed into hydrogen. For the purposes of hydrogen generation, the application of wastewater mixed sludge pre-treated according to Faloye method (Faloye et al. in Int J Hydrog Energy...
-
Features extraction from the electrocatalytic gas sensor responses
PublicationOne of the types of gas sensors used for detection and identification of toxic-air pollutant is an electrocatalytic gas sensor. The electrocatalytic sensors are working in cyclic voltammetry mode, enable detection of various gases. Their response are in the form of I-V curves which contain information about the type and the concentration of measured volatile compound. However,...
-
The design of an intelligent medical space supporting automated patient interviewing
PublicationThe article presents the architecture and results of implementing an application for the intelligent medical space UbiDoDo (Ubiquitous Domestic Doctor's Office). The main purpose of the application is real-time monitoring of the biomedical parameters of a patient in his domestic environment. It allows an immediate reaction to appearing symptoms and provides means to automatically interview the patient and deliver his results to...
-
Flexural behavior of composite structural insulated panels with magnesium oxide board facings
PublicationThe current report is devoted to the flexural analysis of a composite structural insulated panel (CSIP) with magnesium oxide board facings and expanded polystyrene (EPS) core, that was recently introduced to the building industry. An advanced nonlinear FE model was created in the ABAQUS environment, able to simulate the CSIP’s flexural behavior in great detail. An original custom code procedure was developed, which allowed to include...
-
Searching for Solvents with an Increased Carbon Dioxide Solubility Using Multivariate Statistics
PublicationIonic liquids (ILs) are used in various fields of chemistry. One of them is CO2 capture, a process that is quite well described. The solubility of CO2 in ILs can be used as a model to investigate gas absorption processes. The aim is to find the relationships between the solubility of CO2 and other variables—physicochemical properties and parameters related to greenness. In this study, 12 variables are used to describe a dataset...
-
Analysis of possible application of high-temperature nuclear reactors to contemporary large-output steam power plants on ships
PublicationThis paper is aimed at analysis of possible application of helium to cooling high-temperature nuclear reactor to be used for generating steam in contemporary ship steam-turbine power plants of a large output with taking into account in particular variable operational parameters. In the first part of the paper types of contemporary ship power plants are presented. Features of today applied PWR reactors and proposed HTR reactors...
-
Vibration of the bridge under moving singular loads - theoretical formulation and numerical solution
PublicationThe paper presents the results of the numerical analysis of a simple vehicle passing over a simply supported bridge span. The bridge is modelled by a Euler-Bernoulli beam. The vehicle is modelled as a linear, visco-elastic oscillator, moving at a constant speed. The system is described by a set of differential equations of motion and solved numerically using the Runge-Kutta algorithm. The results are compared with the solution...
-
Dynamic state assessment of the water turbine with the power of 600 kW
PublicationThe article discusses the results of experimental studies to assess the dynamic state of the turbine set with the Kaplan turbine. The dynamic assessment was made on the basis of appropriate standards, based on the measurement results of selected parameters of vibration, which have been measured for several states of the machine load. In addition, we attempted to identify the causes of the increased vibration levels based on the...
-
FEM simulation of laminate failure in the three point bending
PublicationThe paper presents a FEM simulation of failure of laminate subjected to the three point bending. The numeri-cal model is based on the equivalent single layer approach with 6-paramater non-linear shell theory kinematics. It is implemented in the non-commercial FEM code. The failure initiation is detected with the use of Tsai-Wu criterion. After the failure onset the progressive failure process is modelled through the appropriate...
-
Extending transition curve in analytical design method
PublicationThe paper presents the problem of extending the transitional curves, using for this purpose an analytical design method. The basis for the analysis of numerical calculations were carried out for a wide set of parameters characterizing the standard geometric system. We considered an importance of the size of radius of the circular arc and return angle of route on the obtained results after the formulation of appropriate theoretical...
-
Using Wearable Electronics to Estimate Usefulness of Heart Rate Variability for Bathing Person Identif Cation
PublicationIn this paper the possibility of person identification based on biosignal is investigated. The work focus on the analysis of the changes in intervals between successive R-waves of electrocardiogram (ECG) recorded by wearable electronics in form of a necklaces. The main idea behind this project is to find efficient tool which may prevent sudden consciousness loss episodes or even sudden death episodes related to rapid temperature...
-
Revalorisation of the Szewalski’s concept of the law of varying the last-stage blade retraction in a gas-steam turbine
PublicationThe article presents the implementations of the free vortex law to the blade of the last stage of a gas-steam turbine. First, a thermodynamic analysis was carried out, determining the parameters at the inlet, then the number of stages of the high and low-pressure part of the turbine was constructed, together with the kinematics and velocity vectors for subsequent stages of the axial turbine. The last step of article was to take...
-
Analysis of Corrugated Coaxial Line with the Use of Body of Revolution and Finite Element Method
PublicationA combination of the body-of-revolution and finite element methods is utilized to the analysis of coaxial lines with corrugated rod and wall. Both periodic and non-periodic structures can be investigated. As the structure is axially symmetrical the two dimensional scalar-vector finite element method can be used, which allows for the investigation of complex geometries and is computationally efficient. A generalized impedance matrix...
-
Wavelet filtering of signals without using model functions
PublicationThe effective wavelet filtering of real signals is impossible without determining their shape. The shape of a real signal is related to its wavelet spectrum. For shape analysis, a continuous color wavelet spectrogram of signal level is often used. The disadvantage of continuous wavelet spectrogram is the complexity of analyzing a blurry color image. A real signal with additive noise strongly distorts the spectrogram based on continuous...
-
Solventless and solvent-minimized sample preparation techniques for determining currently used pesticides in water samples: A review
PublicationThe intensification of agriculture means that increasing amounts of toxic organic and inorganic compounds are entering the environment. The pesticides generally applied nowadays are regarded as some of the most dangerous contaminants of the environment. Their presence in the environment, especially in water, is hazardous because they cause human beings to become more susceptible to disease. For these reasons, it is essential to...
-
Extraction and evaluation of gas-flow-dependent features from dynamic measurements of gas sensors array
PublicationGas analyzers based on gas sensors are the devices which enable recognition of various kinds of volatile compounds. They have continuously been developed and investigated for over three decades, however there are still limitations which slow down the implementation of those devices in many applications. For example, the main drawbacks are the lack of selectivity, sensitivity...
-
H2AX phosphorylation, its role in DNA damage response and cancer therapy
PublicationDouble-strand breaks (DSBs) are the most deleterious DNA lesions, which, if left unrepaired, may have severe consequences for cell survival, as they lead to chromosome aberrations, genomic instability, or cell death. Various physical, chemical, and biological factors are involved in DSB induction. Cells respond to DNA damage by activating the so-called DNA damage response (DDR), a complex molecular mechanism developed to detect...
-
Fast tolerance-aware design optimization of miniaturized microstrip couplers using variable-fidelity EM simulations and re-sponse features
PublicationManufacturing tolerances and other types of uncertainties may considerably affect operation and performance of microwave components and systems. Quantification of these effects is therefore an important part of the design process. It is even more important to obtain designs whose sensitivity to parameter deviations is reduced as much as possible. All of these require statistical analysis carried out at the level of electromagnetic...
-
Improvements and Spatial Dependencies in Energy Transition Measures
PublicationThis article aims to improve one of the newest energy transition measures—the WorldEconomic Forum WEF Energy Transition Index (ETI) and find its driving forces. This paper proposesa new approach to correct the ETI structure, i.e., sensitivity analysis, which allows assessing theaccuracy of variable weights. Moreover, the novelty of the paper is the use the spatial error modelsto estimate determinants of the energy transition on...
-
Solid State Conductivity of Optimized Polypyrrole Coatings on Iron Obtained from Aqueous Sodium Salicylate Solution Determined by Impedance Spectroscopy
PublicationIn this work the optimization procedure for corrosion resistance, surface analysis and electrical properties of PPy-Fe electrodes have been examined. Polypyrrole (PPy) film was electrochemically synthesized in a one step process from an aqueous solution of sodium salicylate and pyrrole with certain concentrations, different parameters and type of polymerization...
-
Evaluation of Respiration Rate Using Thermal Imaging in Mobile Conditions
PublicationRespiratory rate is very important vital sign that should be measured and documented in many medical situations. The remote measurement of respiration rate can be especially valuable for medical screening purposes (e.g. severe acute respiratory syndrome (SARS), pandemic influenza, etc.). In this chapter we present a review of many different studies focused on the measurements and estimation of respiration rate using thermal imaging...
-
Potential energy curves, transition and permanent dipole moments of KRb
PublicationWe present extensive calculations of 48 adiabatic potential energy curves of the KRb molecule. Efforts have been focused on preparing the appropriate basis sets. Compared to previous approaches, the set of new potential energy curves is extended to higher excitations, including the single-excited K(4s2S)+Rb(5d2D) and double-excited K(4p2P)+Rb(5p2P) atomic limits. Larger distances between nuclei are also taken into account. New...
-
Strain-dependent behaviour of cold recycled material mixtures in cyclic compression tests
PublicationThe purpose of the study is to evaluate strain-dependent behaviour of Cold Recycled Material (CRM) mixtures using three frameworks typically applied for Hot Mix Asphalt (HMA): linear viscoelastic (LVE) limits; non-linearity directions; changes in rheological model parameters. To this aim, the complex modulus of three CRM mixtures with different bitumen-to-cement ratio (0.2, 0.6 and 1.8) was measured in cyclic compression mode,...
-
Studying the Effect of Working Conditions on WEDM Machining Performance of Super Alloy Inconel 617
PublicationWire electrical discharge machining (WEDM) has been for many years a precise and efficient non-conventional manufacturing solution in various industrial applications, mostly involving the use of hard-to machine materials like, among other, the Inconel super alloys. The focus of the present study is on exploring the effect of selected control parameters, including pulse duration, pulse-off time and the dielectric flow pressure on...
-
Material Identification of the Human Abdominal Wall Based On the Isogeometric Shell Model
PublicationThe human abdominal wall is an object of interest to the research community in the context of ventral hernia repair. Computer models require a priori knowledge of constitutive parameters in order to establish its mechanical response. In this work, the Finite Element Model Updating (FEMU) method is used to identify an heterogeneous shear modulus distribution for a human abdominal wall model, which is based on nonlinear isogeometric...
-
Ionospheric scintillations computation using real-time GPS observations
PublicationThe following paper presents the results of quasi-real-time determination of the values of phase scintillations indices at the period of ionospheric disturbances that occurred as a consequence of the Sun flares observed on March 7 and 9, 2012. Double-frequency observations with 1-second measurement interval from the EPN (EUREF Permanent Network) network sites located at high latitudes were used for the analysis. To determine the phase...
-
A technique of experiment aided virtual prototyping to obtain the best spindle speed during face milling of large-size structures
PublicationThe paper presents an original method concerning vibration suppression problem during milling of large-size and geometrically complicated workpieces with the use of novel way of selecting the spindle speed. This consists in repetitive simulations of the cutting process for subsequent values of the spindle speed, until the best vibration state of the workpiece is reached. An appropriate method of obtaining a computational model,...
-
A structure and design optimization of novel compact microscrip dual-band rat-race coupler with enhanced bandwidth
PublicationIn the letter, a topology of a novel compact wideband dual-band rat-race coupler has been presented along with its computationally efficient design optimization procedure. Reduction of the circuit size has been achieved by meandering transmission lines of the conventional circuit. At the same time, the number of independent geometry parameters has been increased so as to secure sufficient flexibility of the circuit, necessary in...
-
ANALYSIS AND OPTIMIZATION OF ELECTRIC VEHICLE CHARGING PROCESSES IN TRANSACTIVE ENERGY SYSTEMS
PublicationThe implementation of smart charging of electric vehicles allows operators of local power networks and electricity suppliers to implement new business models for the interaction of electric vehicles with the network. In addition to the optimal selection of Microgrid capacities when charging electric vehicles, it is also important to use different charging methods. To satisfy the interests of all participants of local systems from...
-
The impact of thermomechanical and chemical treatment of waste Brewers’ spent grain and soil biodegradation of sustainable Mater-Bi-Based biocomposites
PublicationDue to the massive plastic pollution, development of sustainable and biodegradable polymer materials is crucial to reduce environmental burdens and support climate neutrality. Application of lignocellulosic wastes as fillers for polymer composites was broadly reported, but analysis of biodegradation behavior of resulting biocomposites was rarely examined. Herein, sustainable Mater-Bi-based biocomposites filled with thermomechanically-...
-
Analiza kohortowa przyczyn bierności zawodowej osób w wieku 45+
PublicationZmiany demograficzne następujące w ostatnich latach w krajach rozwiniętych stawiają nowe wyzwania przed badaczami i praktykami rynku pracy. Jedną z najbardziej zauważalnych konsekwencji „starzenia społeczeństw” jest wydłużenie czasu bierności zawodowej. Jednocześnie w wolniejszym tempie występuje proces wydłużenia czasu aktywności zawodowej. Z punktu widzenia stabilności systemu emerytalnego istotne jest zatem określenie przyczyn...
-
The importance of individual spray properties in performance improvement of a urea-SCR system employing flash-boiling injection
PublicationThe appropriate mixing of a urea–water solution (UWS) with exhaust gases in a selective catalytic reduction system is crucial to efficiently reduce nitrogen oxides and diminish the deposition of liquid wall film. One of the methods to enhance the mixing of the UWS with the exhaust gases is a flash-boiling injection. Its positive effect has been linked with a reduced Sauter mean diameter (SMD) and improved evaporation, but the...
-
Rapid and Reliable Re-Design of Miniaturized Microwave Passives by Means of Concurrent Parameter Scaling and Intermittent Local Tuning
PublicationRe-design of microwave passive components for the assumed operating frequencies or substrate parameters is an important yet a tedious process. It requires simultaneous tuning of relevant circuit variables, often over broad ranges thereof, to ensure satisfactory performance of the system. If the operating conditions at the available design are distant from the intended ones, local optimization is typically insufficient, whereas...
-
HYGRO-MAGNETIC VIBRATION OF THE SINGLE-WALLED CARBON NANOTUBE WITH NONLINEAR TEMPERATURE DISTRIBUTION BASED ON A MODIFIED BEAM THEORY AND NONLOCAL STRAIN GRADIENT MODEL
PublicationIn this study, vibration analysis of single-walled carbon nanotube (SWCNT) has been carried out by using a refined beam theory, namely one variable shear deformation beam theory. This approach has one variable lesser than a contractual shear deformation theory such as first-order shear deformation theory (FSDT) and acts like classical beam approach but with considering shear deformations. The SWCNT has been placed in an axial or...
-
Assessment of the Impact of GNSS Processing Strategies on the Long-Term Parameters of 20 Years IWV Time Series
PublicationAdvanced processing of collected global navigation satellite systems (GNSS) observations allows for the estimation of zenith tropospheric delay (ZTD), which in turn can be converted to the integrated water vapour (IWV). The proper estimation of GNSS IWV can be affected by the adopted GNSS processing strategy. To verify which of its elements cause deterioration and which improve the estimated GNSS IWV, we conducted eight reprocessings...