Filters
total: 1593
filtered: 1385
displaying 1000 best results Help
Search results for: ENGINE ROTATION SPEED
-
The Influence of the Depth of Cut in Single-Pass Grinding on the Microstructure and Properties of the C45 Steel Surface Layer
PublicationThe paper contains the results of a metallographic examination and nanoindentation test conducted for the medium carbon structural steel with low content of Mn, Si, Cu, Cr, and Ni after its grinding to a depth ranging from 2 μm to 20 μm, at constant cutting speed (peripheral speed) of vs = 25 ms−1 and constant feed rate of vft = 1 m/min. Applied grinding parameters did not cause the surface layer hardening, which could generate...
-
Theoretical analysis and experimental tests of tilting pad journal bearings with shoes made of polymer material and low-boiling liquid lubrication
PublicationSelecting the appropriate bearing system for the rotor requires a good knowledge of the available solutions and the operating conditions of the machine. For newly designed machinery operating in adverse conditions, selecting bearings that ensure correct and long-lasting operation can be extremely challenging. Difficulties in- crease when the machine’s operating parameters are beyond the technical capabilities of available technical solutions....
-
Ab-initio study of electrical and optical properties of allylamine
PublicationThe Density functional theory is one of most promising methodology in fast and accurate calculations of electrical and optical properties from the atomic basis. In this paper, we calculate electrical and optical properties of allylamine (2-propen 1- amine) in terms of accuracy and speed of calculations obtained by selection of DFT-1/2 method with ultrasoft Vanderbilt pseudopotentials. Comparison of density of states between...
-
Chosen Analysis Results Of The Prototype Multicell Piezoelectric Motor
PublicationThis paper presents the design, modeling and tests of the prototype multicell piezoelectric motor (MPM). A new concept of the electromechanical structure of the considered prototype is based on three rotating-mode actuators. The electromechanical structure of each actuator has been considered as an independent one - referred to as a “single cell” (single actuator). Combined three resonant actuators generate three traveling waves...
-
Ab-initio study of electrical and optical properties of allylamine
PublicationThe Density functional theory is one of most promising methodology in fast and accurate calculations of electrical and optical properties from the atomic basis. In this paper, we calculate electrical and optical properties of allylamine (2-propen 1- amine) in terms of accuracy and speed of calculations obtained by selection of DFT-1/2 method with ultrasoft Vanderbilt pseudopotentials. Comparison of density of states between molecule...
-
Dynamics of quantum entanglement
PublicationA model of discrete dynamics of entanglement of a bipartite quantum state is considered. It involves a global unitary dynamics of the system and periodic actions of local bistochastic or decaying channel. For initially pure states the decay of entanglement is accompanied by an increase of von Neumann entropy of the system. We observe and discuss revivals of entanglement due to unitary interaction of subsystems. For some mixed states...
-
Evolutionary Ship Track Planning within Traffic Separation Schemes – Evaluation of Individuals
PublicationThe paper presents an extended version of the author’s Evolutionary Sets of Safe Ship Trajectories method. The method plans safe tracks of all ships involved in an encounter including speed reduction manoeuvres, if necessary, and taking into account Rule 10 of COLREGS, which specifies ships’ behaviour within Traffic Separation Schemes governed by IMO. The paper focuses on the evaluation phase of the evolutionary process and shows...
-
Tool Wear Prediction in Single-Sided Lapping Process
PublicationSingle-sided lapping is one of the most effective planarization technologies. The process has relatively complex kinematics and it is determined by a number of inputs parameters. It has been noted that prediction of the tool wear during the process is critical for product quality control. To determine the profile wear of the lapping plate, a computer model which simulates abrasive grains trajectories was developed in MATLAB. Moreover,...
-
Estimation of interior-permanent-magnet-synchronous-motor rotor position by analysis of phase-current derivatives
PublicationThis paper describes an algorithm for estimation of IPMSM rotor angular position. The algorithm uses derivatives of motor phase currents resulting from PWM modulation to obtain the rotor position. The presented method is designed for medium- and high-speed range, since it is based on determination of the EMF vector. Calculation of the motor position is performed in every PWM cycle. The standard SV-PWM method is used to determine...
-
Properties of surface layers of titanium alloy Ti6Al4V after laser melting processes
PublicationThe article presents the investigation results of titanium alloy Ti6Al4V surface layer after laser melting process. The process of laser melting was performed using Nd-YAG laser. The evaluation of structure of the alloy as well as hardness and chemical composition was performed. It was shown that laser melting changes the structure and properties of titanium alloy Ti6Al4V and process parameters as scanning speed affects the thickness...
-
Vibration of the bridge under moving singular loads - theoretical formulation and numerical solution
PublicationThe paper presents the results of the numerical analysis of a simple vehicle passing over a simply supported bridge span. The bridge is modelled by a Euler-Bernoulli beam. The vehicle is modelled as a linear, visco-elastic oscillator, moving at a constant speed. The system is described by a set of differential equations of motion and solved numerically using the Runge-Kutta algorithm. The results are compared with the solution...
-
New concept and analysis of the multicell piezoelectric motor
PublicationThis work presents the design, modeling and tests of the prototype multicell piezoelectric motor (MPM). A new concept of the electromechanical structure of the considered prototype is based on three rotating-mode actuators. The electromechanical structure of each actuator has been considered as an independent one - referred to as a ”single cell” (single actuator). Combined three resonant actuators generate three traveling waves...
-
Multiple-Input Multiple-Output Technique for Underwater Acoustic Communication System
PublicationThe performance of an underwater acoustic communication (UAC) system is limited due to tough propagation conditions in the UAC channel. Multiple-Input Multiple-Output (MIMO) technique can improve the reliability of the data transmission system, increase its speed, increase its range, and reduce the energy consumption. The paper presents an implementation method of MIMO technique in the form of coding the Space-Time Block Code and...
-
A modified method of vibration surveillance by using the optimal control at energy performance index
PublicationA method of vibration surveillance by using the optimal control at energy performance index has been creatively modified. The suggested original modification depends on consideration of direct relationship between the measured acceleration signal and the optimal control command. The paper presents the results of experiments and Hardware- in-the-loop simulations of a new active vibration reduction algorithm based on the energy...
-
Sensorless Disturbance Detection for Five Phase Induction Motor with Third Harmonic Injection
PublicationThe paper presents a sensorless disturbance detection procedure that was done on a five phase induction motor with third harmonic injection. A test bench was developed where a three phase machine serves as disturbance generator of different frequencies. The control of the machines is based on multi scalar variables that ensures an independent control of the motor EMF and the rotor flux. For disturbance identification a speed observer...
-
Solving the Problem of Dynamic Adaptability of Artificial Intelligence Systems that Control Dynamic Technical Objects
PublicationThis paper investigates the increase in the response speed and stability of artificial intelligence systems that control dynamic technical objects. The problem of calculating the optimal time of switching an artificial intelligence system between software classes by the criterion of the rigidity degree of the model of a control object is considered. The solution of this problem is proposed for the general case of the control object...
-
Possibility of Fault Detection in Sensorless Electric Drives
PublicationThe work presents a fault detection method for an induction motor drive system with inverter output filter. This approach make use of a load torque state observer, which complete structure is presented along with the used control structure. Moreover, the demonstrated drive system operates without rotor speed measurement in conjunction with the multiscalar control. The verification of the demonstrated idea was performed on an experimental...
-
Wpływ zmian dopuszczalnych wartości parametrów geometrycznych i kinematycznych na podatność modernizacyjną układów torowych
PublicationPodatnością modernizacyjną nazywamy stopień przystosowania analizowanego odcinka linii kolejowej do zmiany prędkości eksploatacyjnej. Skala możliwych zmian prędkości (w sensie jej zwiększenia) jest wypadkową istniejącego układu geometrycznego linii w planie, ograniczeń lokalizacyjnych oraz dopuszczalnych wartości parametrów geometrycznych i kinematycznych. Jakiekolwiek zmiany tych ostatnich wpływają bezpośrednio na obliczenie elementarnych...
-
Absolute Photoabsorption Cross-Sections of Methanol for Terrestrial and Astrophysical Relevance
PublicationWe investigate the methanol absorption spectrum in the range 5.5–10.8 eV to provide accurate and absolute cross-sections values. The main goal of this study is to provide a comprehensive analysis of methanol electronic-state spectroscopy by employing high-resolution vacuum ultraviolet (VUV) photoabsorption measurements together with state-of-the-art quantum chemical calculation methods. The VUV spectrum reveals several new features...
-
Torsional earthquake-induced pounding between adjacent buildings founded on different soil types
PublicationThis paper investigates the effect of the soil type on the torsional response of build- ings experiencing torsional pounding due to earthquake excitations. Six buildings (one 4-storey building and five 6-storey buildings) with different configurations have been considered. First, pounding between different structures has been analysed for a specified soil type and the effect of the torsional pounding and the contact asymmetry on...
-
Active Site Architecture and Reaction Mechanism Determination of Cold Adapted beta-D-galactosidase from Arthrobacter sp. 32cB
PublicationArthbetaDG is a dimeric, cold-adapted beta-D-galactosidase that exhibits high hydrolytic and transglycosylation activity. A series of crystal structures of its wild form, as well as its ArthbetaDG_E441Q mutein complexes with ligands were obtained in order to describe the mode of its action. The ArthbetaDG_E441Q mutein is an inactive form of the enzyme designed to enable observation of enzyme interaction with its substrate. The...
-
Projektowanie gier komputerowych z wykorzystaniem Unreal Development Kit
PublicationW pracy przedstawiono pakiet narzędziowy Unreal Development Kit (UDK) umożliwiający tworzenie gier w oparciu o silnik Unreal Engine 3 (UE3). Silnik ten umożliwia tworzenie wieloplatformowych, zaawansowanych graficznie gier praktycznie dowolnego typu. UDK jest zasadniczo kompletnym środowiskiem wytwarzania gier oferując rozmaite narzędzia modelowania poziomów, w tym: edytor brył geometrycznych, siatek obiektów i terenu, bibliotekę...
-
COMPOSITE FOOTBRIDGE - SYNERGY EFFECT IN COOPERATION BETWEEN UNIVERSITIES AND INDUSTRY
PublicationPaper presents conditions of science and industry cooperation in Poland (restrictions, barriers, good practice). A key role in initiation of collaboration between units has financial support. What is also important, it is much easier to create innovative solutions on the base of combining the potential of individuals. That is why many countries all over the world look for innovative solutions using budget funds to support grants...
-
MCSA with Normalized Triple Covariance as a bearings diagnostic indicator in an induction motor
PublicationStatistics of bearing failures in induction motors indicate, that they constitute more than 40% of IM damage, therefore bearing diagnosis is very important. Vibration methods for bearing diagnostics have one major disadvantage - they require the availability of the machine for sensors installation. This is the reason for seeking new methods based on motor supply current analysis. Diagnosis of induction motors, conducted remotely...
-
The conception of energetic investigations of the multisymptom fatigue of the simple mechanical systems' constructional materials
PublicationThe article presents the basic assumptions of the research project aimed, as the main scientific purpose, an identification of the slow-changeable energy processes surrounding the high-cycle fatigue of constructional materials within the plain mechanical system, especially the marine one, for diagnostic purposes. There is foreseen an application of alternative diagnostic methods based on energetic observations of the multi-symptom,...
-
Analysis of the regenerative braking process for the urban traffic conditions
PublicationIn a regular drive system, with an internal combustion engine, vehicle braking is connected with the unproductive dissipation of kinetic and potential energy accumulated in the mass of the vehicle into the environment. This energy can constitute up to 70% of the energy used to drive a vehicle under urban conditions. Its recovery and reuse is one of the basic advantages of hybrid and electric vehicles. Modern traffic management...
-
Metoda diagnostyki łożysk na podstawie analizy przebiegów prądu i napięcia zasilającego silnik indukcyjny.
PublicationW niniejszej monografii przedstawiono oryginalne podejście i realizację diagnostyki łożysk silników indukcyjnych przy użyciu metody opartej na pomiarach i analizie iloczynu wartości chwilowych prądu i napięcia zasilającego maszyny. Uzyskane wyniki badań eksperymentalnych na obiektach rzeczywistych okazały się zbieżne z wynikami badań symulacyjnych i potwierdziły, że powstanie uszkodzeń łożysk w silniku skutkuje pojawieniem się...
-
The Imaging of Gdansk Bay Seabed by Using Side Sonar
PublicationThis paper is mainly aimed at presentation of an impact of environmental conditions on imaging accuracy by using hydro-acoustic systems in waters of a high non-uniformity of spatial distribution of hydrological parameters. Impact of refraction on erroneous estimation of range, in case of wave radiation into water under a large angle, like in side sonars or multi-beam echo-sounders, is especially important. In this paper seasonal...
-
Simple gait parameterization and 3D animation for anonymous visual monitoring based on augmented reality
PublicationThe article presents a method for video anonymization and replacing real human silhouettes with virtual 3D figures rendered on a screen. Video stream is processed to detect and to track objects, whereas anonymization stage employs animating avatars accordingly to behavior of detected persons. Location, movement speed, direction, and person height are taken into account during animation and rendering phases. This approach requires...
-
Fluctuation-Enhanced Sensing (FES): A Promising Sensing Technique
PublicationFluctuation-enhanced sensing (FES) is a very powerful odor and gas sensing technique and as such it can play a fundamental role in the control of environments and, therefore, in the protection of health. For this reason, we conduct a comprehensive survey on the state-of-the-art of the FES technique, highlighting potentials and limits. Particular attention is paid to the dedicated instrumentation necessary for the application of...
-
Evaluation of Wear Resistance of Ti alloys used for elements friction of knee endoprosthesis
PublicationThe paper presents research results of resistance to abrasive wear of titanium alloys: Ti6Al4V (commonly used) and Til3Nb13Zr (alloy of new generation) in association with polyethylene (UHMW-PE) predisposed for elements on pair of the knee endoprosthesis. The results were analysed from the point of possibility of an use of new generation titanium alloys as components of such implants. The tests of resistance to abrasive wear of...
-
Modelling of the Movement of Designed Vehicles on Parking Space for Designing Parking
PublicationNowadays, in all cities there is an acute problem of lack of parking spaces. The vehicles are becoming more and more not only in megacities, but also in small cities of the country, and there are no more parking places - the pace of solving the problem is several times slower than the speed of transport growth among the citizens. The article is dedicated to determination of the optimum sizes parking place for designing vehicles...
-
Disturbances of magnetic field in surrounding of mobile, metalic plate
PublicationThe uniform magnetic field of the Earth in the surrounding of a mobile, metalic object undergoes deformation by eddy currents. The influence of the moving conducting object on total magnetic field of the Earth depends on the object's shape, position and speed of the changes relative to the magnetic field's vector of the Earth as well as the electric conductivity and the relative magnetic permeability of the material. The disturbances...
-
IPMSM rotor position estimator based on analysis of phase current derivatives
PublicationThis paper describes an algorithm for estimation of IPMSM angular rotor position. The algorithm uses derivatives of motor phase currents resulting from PWM modulation to obtain the rotor position. The presented method is designed for medium- and high-speed range, since it is based on determination of the EMF vector. Algorithm is characterised by a very simple formulae. The calculation of rotor position is performed in every PWM...
-
Apparent molar volumes and compressibilities of alkaline earth metal ions in methanol and dimethylsulfoxide
PublicationTemperature dependencies of density of magnesium (II), calcium (II), strontium (II), barium (II) perchlorates as well as beryllium (II), and sodium trifluoromethanesulfonates in methanol and dimethylsulfoxide have been determined over the composition range studied. From density data the apparent molar volumes and partial molar volumes of the salts at infinite dilution as well as the expansibilities have been evaluated. The apparent...
-
Investigations on mixture preparation for two phase adiabatic pressure drop of R134a flowing in 5 mm diameter channel
PublicationThe article presents detailed two-phase adiabatic pressure drops data for refrigerant R134a. Study cases have been set for a mass flux varying from 200 to 400 kg/m2 s, at the saturation temperature of 19.4 ◦C. Obtained experimental data was compared with the available correlations from the literature for the frictional pressure drop during adiabatic flow. Influence of mixture preparation on pressure drop was investigated, for...
-
The study of acoustic climate of the Southern Baltic
PublicationThis paper presents the statistical characteristics of seawater properties, which are necessary for predicting the propagation of acoustic waves in selected areas of the Baltic Sea. The statistics were elaborated based on long-term measurements of vertical distributions of sound speed, temperature, and salinity, and the nonlinearity parameter B/A. Nonlinear properties of the environment are considered, in connection...
-
Effect of underwater local cavity welding method conditions on diffusible hydrogen content in deposited metal
PublicationOne of the methods with great potential for applications in underwater repairs is local cavity welding. In local cavity method, cooling conditions and diffusible hydrogen amount in weld metal are nearly the same as those existed during welding in the air. This paper presents the results of literature survey and preliminary tests of the effect of local cavity welding conditions on diffusible hydrogen amount in a deposited metal....
-
Comparison of natural frequencies of a circular saw blade obtained empirically and with FEM
PublicationThe knowledge of the natural frequencies’ values of circular saw blades is necessary to determine the minimal critical rotational speed in which they can work with required stability. Moreover, testing the circular saw blades with more complicated shapes, e.g. which have additional holes inside blades for cleaning knifes or additional indirect teeth in gullets, reveals some kind of problematic properties of these saw blades. The...
-
Simplified Map-based Selection of Optimal Spindle Speeds When Milling Complex Structures
PublicationIn the paper a method for selecting optimal spindle speeds for complex structures during milling operations is presented. It is based on the selection of the spindle speed in accordance with a simple equation resulting from the minimisation of vibration energy, which leads to the minimisation of the work of cut-ting forces presented in previous elaborations by the authors [1]. Optimal spindle speeds are obtained for many points...
-
Research of Emergency Modes of Wind Power Plants Using Computer Simulation
PublicationThe aim of this study is to investigate changes in the wind power plant energy production parameters under the conditions of sudden wind changes and voltage drop. To achieve these goals, a simulation of operation of wind power plants was performed. Twelve wind turbines with variable rotational speed equipped with a Fuhrländer FL 2500/104 asynchronous double-fed induction generator (DFIG) were used, each with an installed capacity...
-
Energy Management for PV Powered Hybrid Storage System in Electric Vehicles Using Artificial Neural Network and Aquila Optimizer Algorithm
PublicationIn an electric vehicle (EV), using more than one energy source often provides a safe ride without concerns about range. EVs are powered by photovoltaic (PV), battery, and ultracapacitor (UC) systems. The overall results of this arrangement are an increase in travel distance; a reduction in battery size; improved reaction, especially under overload; and an extension of battery life. Improved results allow the energy to be used efficiently,...
-
Contribution of dynamic vehicle loads to pavement failure
PublicationPavement surfaces are not ideally even, which causes dynamic loads of vehicle axles. Distribution of dynamic loads of a given axle is similar to normal distribution and can be described by static load and dynamic load coefficient. The dynamic load coefficient depends on road profile, vehicle speed, properties of suspensions and static load of axle. While for a given road section road profile remains constant, vehicle speed and...
-
Analysis of Residual Stresses and Dislocation Density of AA6082 Butt Welds Produced by Friction Sir Welding
PublicationThe Friction Stir Welding (FSW) method was employed to join AA6082 sheets. The welds were produced with different tool traverse speed (200 and 250 mm/min), rotational speed (1000 and 1250 RPM) and tool tilt angle (0 and 2 deg). Based on the analysis of XRD patterns, the total precipitation volume fractions in the nugget zones and the base material were calculated. The FSW process resulted in a reduction in the fraction of precipitates...
-
Effect of Processing Parameters on Strength and Corrosion Resistance of Friction Stir-Welded AA6082
PublicationThe friction stir welding method is increasingly attracting interest in the railway sector due to its environmental friendliness, low cost, and ease of producing high-quality joints. Using aluminum alloys reduces the weight of structures, increasing their payload and reducing fuel consumption and running costs. The following paper presents studies on the microstructure, strength, and corrosion resistance of AA6082 aluminum alloy...
-
Investigation of Weigh-in-Motion Measurement Accuracy on the Basis of Steering Axle Load Spectra
PublicationWeigh-in-motion systems are installed in pavements or on bridges to identify and reduce the number of overloaded vehicles and minimise their adverse eect on road infrastructure. Moreover, the collected trac data are used to obtain axle load characteristics, which are very useful in road infrastructure design. Practical application of data from weigh-in-motion has become more common recently, which calls for adequate attention to...
-
Współczynniki strat energetycznych w elementach napędu hydrostatycznego
PublicationW każdym układzie napędowym należy zastąpić obraz przepływu mocy opisany dotychczas powszechnie stosowanym wykresem Sankey’a spadku mocy zgodnego z kierunkiem przepływu mocy proponowanym przez autora wykresem wzrostu mocy w układzie przeciwnego do kierunku przepływu mocy. Należy więc opisywać straty i sprawność energetyczną a także pole pracy każdego silnika i układu napędowego jako zależne od wielkości fizycznych niezależnych...
-
Comparison of Tracking Methods in Respect of Automation of Animal Behavioral Test
PublicationAutomation in experiments carried out on animals is getting more and more important in research. Computers take over laborious and time-consuming activities like recording and analysing images of experiment scene. The first step in an image analysis is finding and distinguishing between the observed animals, and then tracking all objects during the experiment. In this paper four tracking methods are presented. Quantitative and...
-
Emotion Recognition - the need for a complete analysis of the phenomenon of expression formation
PublicationThis article shows how complex emotions are. This has been proven by the analysis of the changes that occur on the face. The authors present the problem of image analysis for the purpose of identifying emotions. In addition, they point out the importance of recording the phenomenon of the development of emotions on the human face with the use of high-speed cameras, which allows the detection of micro expression. The work that was...
-
A bound on the number of middle-stage crossbars in f-cast rearrangeable Clos networks
PublicationIn 2006 Chen and Hwang gave a necessary and sufficient condition under which a three-stage Clos network is rearrangeable for broadcast connections. Assuming that only crossbars of the first stage have no fan-out property, we give similar conditions for f-cast Clos networks, where f is an arbitrary but fixed invariant of the network. Such assumptions are valid for some practical switching systems, e.g. high-speed crossconnects....