Filters
total: 1470
filtered: 1249
-
Catalog
Chosen catalog filters
displaying 1000 best results Help
Search results for: STEEL SANDWICH PANEL
-
The Dominant Influence of Plastic Deformation Induced Residual Stress on the Barkhausen Effect Signal in Martensitic Steels
PublicationThe paper presents the results of investigation of the influence of plastic deformation on the magnetic properties of martensitic steel (P91 grade). The properties of the hysteresis loops as well as of the Barkhausen effect (BE) signal are analysed for both tensile and compressive loading up to ε = 10% of plastic deformation. The choice of the steel and of the deformation range is unique, since for such combination one can expect...
-
Experimental investigation of joint with positive eccentricity in CFS truss
PublicationDue to technological restrictions, in the case of trusses made of CFS open cross-sections, positive eccentricities in the truss joints have become very frequent. Therefore studies concerning the load-bearing capacity of truss joints with positive eccentricity were undertaken. It was assumed that the resistance of cold-formed steel (CFS) open cross-section truss joints located on compression chords and with positive eccentricity...
-
SHM System of the Roof Structure of Sports Arena “Olivia”
PublicationThe paper presents a structural health monitoring system of the Sports Arena “Olivia” in Gdansk, Poland. The system was installed because of doubts about the roof stability due to observed buckling of the steel truss members. The SHM system was based on nonlinear FEM models used for detection of type of near failure modes of the roof. The application of detailed FEM model in current state updated on data from in situ loading testes...
-
Dynamic Nanoimpedance Characterization of the Atomic Force Microscope Tip-Surface Contact
PublicationNanoimpedance measurements, using the dynamic impedance spectroscopy technique, were carried out during loading and unloading force of a probe on three kinds of materials of different resistivity. These materials were: gold, boron-doped diamond, and AISI 304 stainless steel. Changes of impedance spectra versus applied force were registered and differences in the tip-to-sample contact character on each material were revealed. To...
-
Effect of Linear Energy and Microstructure on the Content of Residual Hydrogen in Welded Joints made of Superduplex Steels
PublicationThe article presents tests concerning the content of retained hydrogen present in FCAW and SAW welded joints made of superduplex steel. The use of various welding technologies resulted in the obtainment of welds having different microstructures and ferrite contents. Measurements of retained hydrogen present in joints (performed using the complete combustion method) revealed various contents of hydrogen in the base material and...
-
Multisource model of ship electric field
PublicationA steel-hulled ship in sea water produces an electric field around itself. The source of this field are electrochemical processes and ship's cathodic protection. The analysis of the electric field around the ship is important by the reason of the ship's identification and counter-mine protection. The paper presents a simplified model of the ship's multisource electric field, which allows to calculate the electric field distribution...
-
Fatigue life prediction of notched components under size effect using strain energy reformulated critical distance theory
PublicationNotch and size effects show significant impact on the fatigue performance of engineering components, which deserves special attention. In this work, a strain energy reformulated critical distance theory was developed for fatigue life prediction of notched components under size effect. Experimental data of different notched specimens manufactured from GH4169, TC4, TC11 alloys and low carbon steel En3B were used for model validation...
-
Increasing the lifetime of engineering structures through the use of composite laggings
PublicationThe use of composite laggings prevents concrete (chemical and biological) corrosion. Columns coated with composite or reinforced composite are more resistant to negative environmental impact on concrete or steel. The mechanical properties of the reinforced casing also cause that these types of columns are more resistant to lateral forces. The applied casing limits carbonization of concrete and cyclical freezing and thawing with...
-
Analysis of the influence of geometrical imperfections on the equivalent load stabilizing roof truss with lateral bracing system
PublicationThe paper is focused on the numerical analysis of the stability and load bearing capacity of a flat steel truss. The structure was supported by elastic lateral braces. The translational and rotational brace stiffness was taken into account. The linear buckling analysis were performed for the beam and shell model of the truss. The nonlinear static analysis were conducted for the structure initial geometric imperfections. As a result...
-
Improvement of electrochemical action of zinc-rich paints by addition of nanoparticulate zinc
PublicationThe influence of nanosized particles on electrochemical action of standard zinc-rich paints by means of SEM as well as potential and impedance measurements has been investigated. The motivation for doing this was to obtain additional electrical connection between the spherical microparticles themselves and zinc particles and steel substrate. Overall zinc content was at the level of 92% by weight. Samples with different concentration...
-
Spawalność ferrytyczno-austenitycznej stali odpornej na korozję typu dupleks 2205 w warunkach podwodnych
PublicationPraca dotyczy problemów spawalności stali odpornej na korozję typu dupleks w warunkach spawania mokrego elektrodami otulonymi i lokalną komorą suchą. Całość rozprawy składa się z dwóch części. Część pierwsza to przegląd literatury, w którym omówiono główne problemy wynikające z przeniesienia procesu spawania pod wodę oraz sposoby minimalizowania negatywnego wpływu środowiska. Część druga jest częścią doświadczalną, zawiera tezę...
-
Pool boiling of nanofluids on rough and porous coated tubes: experimental and correlation
PublicationThe paper deals with pool boiling of water-Al2O3 and water- Cu nanofluids on rough and porous coated horizontal tubes. Commercially available stainless steel tubes having 10 mm outside diameter and 0.6 mm wall thickness were used to fabricate the test heater. The tube surface was roughed with emery paper 360 or polished with abrasive compound. Aluminium porous coatings of 0.15 mm thick with porosity of about 40% were produced by...
-
The geodetic monitoring of the engineering structure – a practical solution of the problem in 3D space
PublicationThe study raises the issues concerning the automatic system designed for the monitoring of movement of controlled points, located on the roof covering of the Forest Opera in Sopot. It presents the calculation algorithm proposed by authors. It takes into account the specific design and location of the test object. High forest stand makes it difficult to use distant reference points. Hence the reference points used to study the stability...
-
Building Information Modelling as an opportunity and risk for stakeholders involved in construction investment process
PublicationThe requirements to apply Building Information Modelling (BIM) in public investments worldwide are currently very high. Significant interest (sometimes formulated also as a requirement) in BIM technology can be observed also among private investors. Design technology that applies BIM is supported by many private investors due to its numerous advantages. A growing group of construction designers (steel, concrete and reinforced concrete...
-
Autogenous Fiber Laser Welding of 316L Austenitic and 2304 Lean Duplex Stainless Steels
PublicationThis study presents results of experimental tests on quality of dissimilar welded joints between 316L austenitic and 2304 lean duplex stainless steels, welded without ceramic backing. Fiber laser welded butt joints at a thickness of 8 mm were subjected to non‐destructive testing (visual and penetrant), destructive testing (static tensile test, bending test, and microhardness measurements) and structure observations (macro‐ and...
-
Effect of wet Hydrogen Sulfide on Carbon Steels Degradation in Refinery Based on Case Study
PublicationMaterial degradation caused by wet hydrogen sulfide (Wet H2S) is one of the major issues in refineries. Carbon steel is the main construction material used in refineries and is subjected not only to thickness loss but the hydrogen is the major concern. H2S leads to high atomic hydrogen penetration in steel which causes degradation in the form of blistering and/or cracking (HIC/SOHIC) and stress cracking in the area of welds and...
-
Does pandemic denial help or harm? Belief in COVID-19 and experience of it affect psychological consequences of using neurotic defence mechanisms
PublicationObjective: The COVID-19 pandemic may activate thoughts of death, leading to aversive psychological states. In such situations, defence mechanisms emerge; however, their adaptability depends on many factors. The aim of the study was to investigate the relationship between neurotic defence style and depressive symptoms. We assumed that the sense of coherence underlies this correlation and investigated how both believing (or not)...
-
From tryptophan to novel mitochondria-disruptive agent, synthesis and biological evaluation of 1,2,3,6-tetrasubstituted carbazoles
PublicationMitochondrial targeting plays an important role in anticancer therapy. The Mn(III)-promoted cyclization of 5- (1H-indol-3-yl)-3-oxopentanoic acid allow to obtain novel substituted carbazole derivatives that can act as mitochondria-disruptive agents. The starting materials used for the synthesis of these new aminocarbazoles are oxopentanoate derivatives of tryptophan. The scope and limitation of this method of synthesis are determined...
-
Enhancement of lift and drag performances of a NACA0012 airfoil by multi-DBD plasma actuator with additional floating interelectrodes
PublicationIt is clear that the improvement of aircraft aerodynamic performances is currently and will continue to be a significant area of research for the aeronautical industry. The current study is focused on theenhancement of aerodynamic airfoil performances by using a multi-DBD plasma actuator mounted around the model leading-edge. Experiments have been conducted at the University of Orleans, in the 2 m x 2 m test section of a large...
-
Novel N-(aryl/heteroaryl)-2-chlorobenzenesulfonamide derivatives: synthesis and anticancer activity evaluation
PublicationA new series of N-(aryl/heteroaryl)-2-chlorobenzenesulfonamide derivatives 4-21 have been synthesized, and evaluated at the National Cancer Institute (USA) for their in vitro activities against a panel of 60 different human cancer cell lines. Among them, compounds 16, 20 and 21 exhibited remarkable cytotoxic activity against numerous human cancer cell lines. We found that sulfonamide derivative 21 appeared to be more selective...
-
STILL ‘FEW, SLOW AND LOW’? ON THE FEMALE DIMENSION OF TECHNOLOGY, LABOUR MARKETS AND ECONOMIC ACTIVITY: EVIDENCE FOR THE PERIOD OF 1990-2017
PublicationThe known in empirical economics question ‘Why so Few? Why so Slow? Why so Low?’ refers here to the persistently small number of women involved in innovative activities, the slowness of change in the inequalities between women and men in these fields, and women’s continuing lower rank in business and academic positions. In developing countries, women`s labour and entrepreneurial activity remains an ‘untapped resource’ for economic...
-
Quinoline-based thiazolyl-hydrazones target cancer cells through autophagy inhibition
PublicationHeterocyclic pharmacophores such as thiazole and quinoline rings have a significant role in medicinal chemistry. They are considered privileged structures since they constitute several Food and Drug Administration (FDA)-approved drugs for cancer treatment. Herein, we report the synthesis, in silico evaluation of the ADMET profiles, and in vitro investigation of the anticancer activity of a series of novel thiazolyl-hydrazones based...
-
O kształtowaniu stalowych, wieloprzęsłowych mostów drogowych
PublicationW referacie autor przedstawił główne trendy i swoje własne uwagi odnośnie koncepcyjnego projektowania wieloprzęsłowych mostów stalowych. Bazując na zakończonych projektach autor przedstawił teoretyczne i techniczne problemy które wystąpiły podczas projektowania bądź budowy wybranych obiektów mostowych.
-
Modelling of in-plane wave propagation in a plate using spectral element method and Kane-Mindlin theory with application to damage detection
PublicationThis paper presents results of experimental and numerical analyses of in-plane waves propagatingin a 5 mm-thick steel plate in the frequency range of 120-300 kHz. For such a thickness/frequency ratio,extensional waves reveal dispersive character. To model in-plane wave propagation taking into account thethickness-stretch effect, a novel 2D spectral element, based on the Kane-Mindlin theory, was formulated. Anapplication of in-plane...
-
Fatigue resistance investigation of the IC engine MB11 bearings, working under conditions of dynamic unidirectional loadings
PublicationThe slide bearing material MB11 fatigue resistance has been investigated with the application of SMOK - test stand in which dynamic unidirectional loadings to the test bearing is generated. Slide bearing layer consists of the bronze MB11 ( Cu Pb22 Sn 3 ) sintered to the steel shell. Each of the tested bearing has been subject to the standard 20-hour test, under conditions of the full fluid lubrication. Methodology of the experiments,...
-
Sliding bearings with sintered bronze bush lubricated by contaminated water with solid particles – Theoretical and experimental studies
PublicationSliding journal bearings lubricated with water coming directly from the environment are a solution used in shipbuilding, pumps and hydropower. However, the working fluid or surrounding water cannot always be filtered because of design limitations, which often causes the problem of premature wear of these sensitive bearings. The research conducted made it possible to assess the wear of sliding bearings lubricated with water containing...
-
Dynamic effect of the vehicle passing under lightweight footbridge.
PublicationThe paper describes a numerical study of dynamic response of cable-stayed steel footbridge for a big lorry passing underneath. The footbridge is an existing object crossing Wolska street in Warsaw. The structural model of footbridge was verified by dynamic test loading. A numerical study of a vehicle passing under footbridge is presented. 2D and 3D incompressible flow fields are modeled using sliding mesh in transient CFD computation....
-
DETERMINANTY WZROSTU POLSKIEGO EKSPORTU PRZEMYSŁU PRZETWÓRCZEGO – ANALIZA DŁUGOOKRESOWA
PublicationGłównym celem artykułu było określenie determinant eksportu polskiego przemysłu przetwórczego na podstawie danych pochodzących z 13 podsekcji przetwórstwa przemysłowego wyodrębnionych zgodnie z NACE 1.1. Analiza z wykorzystaniem modelu ECM objęła lata 1995–2011 i została przeprowadzona dwutorowo – dla całej sekcji przemysłu przetwórczego oraz dla poszczególnych jego podsekcji. Autorki zbadały, jak popyt zagraniczny, popyt krajowy,...
-
Zagrożenia korozyjne stali nierdzewnych w przemyśle spozywczym
PublicationPrzedstawiono przyczyny występowania zagrożeń korozyjnych stali nierdzewnych w przemyśle spożywczym. Szczegółowo omówiono mechanizm oraz sposób zapobiegania korozji wżerowej, szczelinowej oraz pękania korozyjnego. Zaprezentowano dokumentację fotograficzną omówionych typów korozji. Wskazano podstawowe problemy związane z doborem materiałów konstrukcyjnych do budowy instalacji w przemyśle spożywczym.
-
REMONTY I PRZEBUDOWY DACHÓW Z ZASTOSOWANIEM ELEMENTÓW LEKKIEJ OBUDOWY
PublicationW artykule przedstawiono przykładowe rozwiązania remontów i przebudowy dachów. Omówiono rozwiązania zmiany materiału pokrycia zarówno bez dodawania warstwy izolacyjnej, jak i z ułożeniem dodatkowej warstwy ocieplenia na istniejącej połaci dachowej a także sposób przebudowy dachu, polegający na ustawianiu nowej, lekkiej konstrukcji nośnej dachu, bezpośrednio na istniejącym pokryciu dachu płaskiego.
-
Determination of Failure Causes of a Steam Turbine Casing
PublicationThe paper presents results of research and failure analysis undertaken to determine failure causes of a steam turbine casing. After 130,000 hours of service the crack in a outer shell of the turbine casing was found. The inner shell of the casing was made of cast steel grade G21CrMoV5-7, and the outer shell of grade G20CrMo4-5. Following research were performed in order to determine causes of the casing failure: chemical analysis;...
-
Legislation and Practice of Selected State Aid Issues, According to EU and Polish Law
PublicationThe dataset encompasses several tables, each consisting of three elements: legislation, jurisprudence and scientific articles on numerous subjects and economic activities receiving public financial support in the form of state aid instruments. The set includes a subjective list of the most commonly used and/or disputable examples of granting aid, such as for (local) airports and airlines, steel production, shipyards, and coalmines....
-
Wpływ sztywności podpór bocznych na nośność kratownic dachowych
PublicationPrzeprowadzono analizę numeryczną wpływu sztywności podpór bocznych kratownicy dachowej na jej nośność w zakresie sprężystym. Zastosowano nieliniową analizę problemu wprowadzając dwa warianty modelu konstrukcji: z imperfekcjami geometrycznymi na podstawie normy PN-90/B-03200 oraz z imperfekcjami obciążeniowymi na podstawie Eurocode 3: Design of Steel Structures . Wyznaczono siły w stężeniach oraz porównano je z odpowiednimi zaleceniami...
-
Protection of bridges against stray current corrosion
PublicationA case study of Siennicki Bridge stray current corrosion hazard is presented. A corrosion risk was caused by incorrectly designed tram line traction which goes over the bridge. No dielectric insulation between running rails and bridge steel construction was used. A variety of protection methods against stray currents are described. Characteristics of the endangered bridge were described. Impressed current cathodic protection system...
-
Assesment of (Mn,Co)3O4powders for possible coating material for SOFC/SOEC interconnects
PublicationIn this work (Mn,Co)3O4 spinel powders with different Mn:Co ratio (1:1 and 1:2) and from different commercial suppliers are evaluated for possible powder for production of interconnect coatings. Sinterability of the powders is evaluated on pressed pellets sintered in oxidizing and in reducing/oxidizing atmospheres. For selected powder, coatings are then prepared by the electrophoretic deposition method on Crofer 22 APU stainless...
-
Detection of debonding in reinforced concrete beams using ultrasonic transmission tomography and hybrid ray tracing technique
PublicationThis paper concerns inspection of reinforced concrete elements, with particular emphasis on assessing the quality of the adhesive connection between steel and concrete. A novel theoretical model was developed to determine the paths of transmitted, refracted and reflected elastic waves as well as a creeping wave propagated along the inclusion surface. Imaging the internal structure of tested beams was based on wave propagation measurements...
-
Stability of roof trusses stiffened by trapezoidal sheeting and purlins
PublicationIn the article linear buckling analysis of a set of steel trusses braced by purlins and trapezoidal sheeting are conducted. The buckling load factor due to the height of a corrugated sheeting profile is investigated in parametric studies. The minimal height of trapezoidal sheeting required for preventing the sheeting and chords of the trusses against the buckling is obtained. Two groups of models are considered: “axial” model as...
-
Lamb wave propagation in a single lap adhesive joint
PublicationThe aim of the paper is the analysis of Lamb wave propagation in adhesive joints. The research was performed on a single lap adhesive joint of two steel plates. Two types of joints, namely an intact and with defect were considered. In experimental investigations the condition assessment of the joint was performed with the use of antisymmetric Lamb waves excited by a plate piezo actuators and measured by a laser vibrometer. Numeri-cal...
-
Normal stress distribution in built‑up cold‑formed column in relation to interconnecting bolt spacing
PublicationIn order to increase a stiffness of cold-formed steel (CFS) elements it is practised to built-up the cross-section. In the analysed case, a main element is strengthened by adding extra chord in contact partially along the column. This additional chord acts as a longitudinal stiffener connected with the main section by series of bolts. Authors check whether rules applied over the years, for hot-rolled elements, can be indiscriminately...
-
The influence of stainless steels microstructure evolution on the mechanical properties of pressure installation elements
PublicationIn this paper results of FEM analysis performed for pipe and 90o elbow, made of super duplex stainless steel, after precipitation of sigma phase (),were presented. Heat treatment conditions simulate accidental overheating that can occur in nuclear installations after cooling circulation fails. For initial and modified microstructure tensile test was performed and numerical description of work hardening curves was done. Verification...
-
The influence of stainless steels microstructure evolution on the mechanical properties of pressure installation elements
PublicationIn this paper results of FEM analysis performed for pipe and 90o elbow, made of super duplex stainless steel, after precipitation of sigma phase (s), were presented. Heat treatment conditions simulate accidental overheating that can occur in nuclear installations after cooling circulation fails. For initial and modified microstructure tensile test was performed and numerical description of work hardening curves was done. Verification...
-
Does technology matter for economic development? Empirical evidence for Latin American Countries
PublicationThe spread of new Information and Communication Technologies (ICTs) has been recognized worldwide. ICTs are broadly perceived as tools facilitating economic growth and development, especially in backward countries. They are easy and cheap to adopt, require minimum skills for effective use, and bring opportunities for disadvantaged societies. They enable education, knowledge dissemination and sharing, and processing and storing...
-
Enhancing Economic Development Through ICT-Based Governance: Evidence for Developing Countries
Publicationhis shows novel empirical evidence on how e-government solutions enhance the emergence of inclusive societies, increase institutional quality, and through that channels dynamize economic development in developing countries. With this aim we examine digital development inequalities adopting 2 core ICT indicators: mobile cellular telephony and Internet users; and gross per capita income and Human Development Index to show the level...
-
Uncovering the invisible barriers to women’s success
PublicationIn the area of science and higher education, as in business and politics, the job situation of women is improving, and the percentage of women on executive positions is increasing. However, there is still a serious underrepresentation of women in the highest decision-making bodies. Ladies also take part in the strategic institutional events less frequently. There are still serious disproportions in academic and management positions,...
-
Reshaping financial systems: The role of ICT in the diffusion of financial innovations – Recent evidence from European countries
PublicationExchange-traded funds (ETFs) are among the fastest-growing types of innovative financial products. The emergence and spread of these instruments have been facilitated by the digital revolution. Information and communication technology (ICT) is profoundly reshaping the global economic landscape, laying solid foundations for unrestricted and unbounded flows of information and knowledge, eliminating information asymmetries, and furthering...
-
Financial Markets and Bankruptcy Systems: Is there a Relationship?
PublicationPurpose: Filling the cognitive gap in the theory of ex-post transaction costs, i.e., at the stage of enforcing market transactions by examining the relationship between friendliness/severity of the bankruptcy and restructuring law towards debtors, the level of development of financial markets, the effectiveness of the judicial system and the rate of debt recovery. Design/Methodology/Approach: In the research, the following methods...
-
Relationship between wages, labour productivity and unemployment rate in new EU member countries
PublicationThe main aim of this article is to find out the extent to which relative labour productivity and relative unemployment rate changes determine relative wage changes. We use average annual macro-data for the period 2002-2013 for Poland and other 5 new EU members: Estonia, Hungary, Slovak, Czech Republic and Slovenia. Using Poland as benchmark, rst we examine the correlation between wage, productivity and unemployment rate changes...
-
The impact of equity pledge on inefficient investment: a perspective from family entrepreneurship
PublicationAs an efficient and convenient financing method, equity pledges may have a heterogeneous impact on the inefficient investment of family firms. In order to verify this point, this paper takes A-share listed family enterprises from 2010 to 2021 as a research sample. It conducts an empirical test on the impact of equity pledges on inefficient investment in family firms by constructing a panel regression model. The results show...
-
System sterowania indukcyjnym silnikiem liniowym na bieżni liniowej - analiza problemów działania wykorzystanych protokołów komunikacyjnych
PublicationW artykule opisano stanowisko laboratoryjne z silnikiem liniowym na bieżni liniowej znajdujące się w Katedrze Energoelektroniki i Maszyn Elektrycznych na Wydziale Elektrotechniki i Automatyki Politechniki Gdańskiej oraz omówiono, w jaki sposób rozwiązano problemy związane z działaniem wykorzystanych w systemie sterowania protokołów komunikacyjnych. Stanowisko ma charakter dydaktyczny. W skład stanowiska wchodzi indukcyjny silnik...
-
Force transfer and stress distribution in short cantilever deep beams loaded throughout the depth with a various reinforcement
PublicationDeep beams used as the main reinforced concrete structural elements which taking over the load and stiffening construction are often found in high-rise buildings. The architecture of these buildings is sometimes sophisticated and varied, arouse the admiration of the majority of recipients, and thus causing an engineering challenge to correctly design the structural system and force transfer. In such structures is important to shape...