Filters
total: 1275
filtered: 910
Search results for: COLUMN–BASE CONNECTIONS
-
Experimental investigations on concrete beams reinforced with CFRP lamellas
PublicationPaper presents experimental investigation made on two concrete beams reinforced with internal Carbon Fibre Reinforced Polymer (CFRP) lamellas (i.e. strips, bands). The reinforcement geometrical arrangement was similar as in normal concrete beams reinforced with steel bars and stirrups. The beams were destroyed by the shear forces, as intended. Obtained load-carrying capacities were lower as expected: below 40% of a calculated value....
-
Strong ellipticity conditions and infinitesimal stability within nonlinear strain gradient elasticity
PublicationWe discuss connections between the strong ellipticity condition and the infinitesimal instability within the nonlinear strain gradient elasticity. The strong ellipticity (SE) condition describes the property of equations of statics whereas the infinitesimal stability is introduced as the positive definiteness of the second variation of an energy functional. Here we establish few implications which simplify the further analysis...
-
Scaling of signed residue numbers with mixed-radix conversion in FPGA with extended scaling factor selection
PublicationA scaling technique of signed residue numbers in FPGA is proposed. The technique is based on conversion of residue numbers to the Mixed-Radix System (MRS). The scaling factor is assumed to be a moduli product from the Residue Number System (RNS) base. Scaling is performed by scaling of MRS terms, the subsequent generation of residue representations of scaled terms, binary addition of these representations and generation of residues...
-
Application of cyanated asphaltenes in gas-phase adsorption processes for removal of volatile organic compounds
PublicationThe paper presents an innovative, chemically modified (methylcyanated) asphaltene-based adsorbent that can be an inter-esting low-cost alternative for traditional adsorbents. Adsorption properties of adsorbents were examined by inverse gas chromatography technique, adsorption isotherms, and breakthrough curves. A significant increase in retention volume for pyridine, 2-pentanone, nitropropane, toluene, and 1-butanol was observed....
-
Load-carrying capacity of axially loaded concrete-filled steel tubular columns made of thin tubes
PublicationAn experimental investigation was conducted on 30 CFST columns. An influence of the following factors on load-carrying capacity of the investigated columns was analyzed: the column slenderness (l1 = 42, l2 = 27 and l3 = 15), the tube thickness (the reinforcement ratio was equal to 4% or 6%), the way of applying the load to CFST columns (through the concrete core or through the entire cross-section), the bond strength between a...
-
On jump conditions at non-material singular curves in the resultant shell thermomechanics
PublicationThe global, refined, resultant, two-dimensional (2D) balance laws of mass, linear and angular momenta, and energy as well as the entropy inequality were formulated by Pietraszkiewicz (2011) as exact implications of corresponding laws of 3D rational thermomechanics. In case of a shell with the regular base surface and all resultant surface fields differentiable everywhere on it and at any time instant, the local laws of the resultant...
-
Theoretical and Architectural Framework for Contextual Knowledge Bases
PublicationThe paper presents the approach aimed at building modularized knowledge bases in a systematic, context-aware way. The paper focuses on logical modeling of such knowledge bases, including an underlying SIM metamodel. The architecture of a comprehensive set of tools for knowledge-base systems engineering is presented. The tools enable an engineer to design, create and edit a knowledge base schema according to a novel context approach...
-
Impact of reclaimed asphalt pavement (RAP) on low-temperature properties of asphalt concrete
PublicationHot mix recycling is a practice which enables reusing materials from old asphalt pavements. Current Polish regulations allow usage of RAP only for binder and base courses, and its amount is limited. Asphalt mixtures with RAP material have to fulfil requirements stated for typical asphalt mixtures. The research presents low-temperature properties of twelve different asphalt concretes with RAP material, determined using three-point...
-
One-dimensional chaos in a system with dry friction: analytical approach
PublicationWe introduce a new analytical method, which allows to find chaotic regimes in non-smooth dynamical systems. A simple mechanical system consisting of a mass and a dry friction element is considered. The corresponding mathematical model is being studied. We show that the considered dynamical system is a skew product over a piecewise smooth mapping of a segment (the so-called base map). For this base map we demonstrate existence of...
-
Prognozowanie krzywej osiadania pala wierconego z iniekcją ciśnieniową pod podstawą
PublicationArtykuł jest kontynuacją tematyki autora dotyczącą mechanizmu działania iniekcji ciśnieniowej pod podstawą pala wierconego. W poprzednich publikacjach, autor wykazał, że iniekcja ta w głównej mierze uaktywnia zwiększone opory gruntu wzdłuż pobocznicy pala. Na tej podstawie w niniejszym artykule zaprezentowano procedurę obliczeniową prognozowania krzywą osiadania pala wierconego z iniekcją ciśnieniową pod podstawą. Przedstawiono...
-
Analiza porównawcza metod zwiększania nośności i sztywności stalowych, doczołowych węzłów śrubowych.
PublicationInnowacyjna, w porównaniu z dotychczas stosowanym sposobem, metoda obliczania nośności stalowych węzłów została wdrożona wraz z normami europejskimi. Pozwala ona dokładniej odwzo-rować rzeczywistą pracę poszczególnych części węzła, gdyż wynik obliczeń uzależniony jest od znacznie większej liczby zmiennych. Dzięki postępowi technologicznemu w zakresie metalurgii oraz badaniom naukowym obecnie możliwe jest wzmacnianie połączeń...
-
Rearrangeability in multicast Clos networks is NP-complete
PublicationPrzestrajalność w polach Closa z połączeniami jeden do jeden jest problemem wielomianowym. W pracy pokazano, że w polach z połączeniami jeden do wiele problem ten jest NP zupełny.Three-stage elos networks are commutation networks with circuit switching. So far, graph theory has been very useful tool for solving issues related to these networks with unicast connections. This is so because if elos network is represented as a bipartite...
-
Mechanical and Microstructural Characterization of TIG Welded Dissimilar Joints between 304L Austenitic Stainless Steel and Incoloy 800HT Nickel Alloy
PublicationIn this article, the mechanical properties and microstructure of 304L austenitic stainless steel/Incoloy 800HT nickel alloy dissimilar welded joints are investigated. The joints were made of 21.3 mm × 7.47 mm tubes using the TIG process with the use of S Ni 6082 nickel filler metal. No welding imperfections were found and high strength properties of joints were obtained, meeting the assumed acceptance criteria of the product’s...
-
Size Exclusion Coupled to Reversed Phase Liquid Chromatography for the Characterization of Cranberry Products
PublicationA combination of solvent extraction, size exclusion purification, and reversed-phase liquid chromatography with UV absorption and fluorescence detection was here used for the determination of flavan-3-ols and related oligomeric compounds in cranberry products. The method relied on robust, simple, and inexpensive instrumental equipment present in most of routine analytical laboratories. Sample extracts in methanol/water/hydrochloric...
-
Separation of Volatile Oxygen-containing Organic Compounds by Gas Chromatography - selectivity comparison of different polarity stationary phases
PublicationThis paper present a results of the separation of 36 reference compounds belonging to the group of Volatile Oxygen-Containing Organic Compounds (OVOCs) using capillary gas chromatography with flame ionization detector (GC-FID) and three stationary phases of different polarity. A selectivity has been studied regarding to OVOCs and n -alkanes. The most useful for the separation of the group OVOCs is a polar ionic liquid stationary...
-
Assessment of technical condition and repair of steel structure elements on the example of fire damage in a warehouse building
PublicationThe paper analyses a case study on the structural assessment of warehouse building partially damaged by fire caused by external source (fire of lorries close to the building). The authors focus on the site investigations and laboratory test results prior to assessing actual condition of the structural elements. Both strengthening concept and repair procedure of a steel column are addressed here. A short literature survey in the...
-
Deterministic Rendezvous in Restricted Graphs
PublicationIn this paper we consider the problem of synchronous rendezvous in which two anonymous mobile entities (robots) A and B are expected to meet at the same time and point in a graph G = (V;E). Most of the work devoted to rendezvous in graphs assumes that robots have access to the same sets of nodes and edges, where the topology of connections may be initially known or unknown. In our work we assume the movement of robots is restricted...
-
Quasi-analytical Near-to-Far Field Transformation Based on Field Matching Method for Scattering Problems
PublicationA new quasi-analytical near-to-far field transformation based on field matching method (field expansion in a base of Hankel functions) is presented. This approach uses finite element method to obtain near field, then the field is expressed in a base of Hankel functions. The evaluated coefficients allow to calculate the field outside the numerical domain, also in a far distance. The main advantage of the proposed technique is avoiding of...
-
Installation of CMC columns in overconsolidated clays
PublicationDuring rigid inclusions execution in the subsoil some monitoring data are registered by a drilling rig for quality control. The use of these data can improve the design procedure of soil improvement as they can provide some information about the position of bearing strata and the energy necessary to install the column in the ground. In this paper the parameters registered in a drilling machine are described, the installation...
-
Instantaneous Impedance Analysis of Non-Stationary Corrosion Process: a Case Study of Carbon Steel in 1M HCl
PublicationThe paper concerns the problem of evaluation of stationarity of carbon steel corrosion in 1M HCl. Comparison of corrosion rate with addition of corrosion inhibitor to the reference measurement is the most often used way of evaluating inhibitor efficiency. Such an approach is valid only if corrosion rate is a stationary process. Two complementary techniques were used simultaneously: volumetric analysis of evolved hydrogen and instantaneous...
-
Improving the Performance of Ontological Querying by using a Contextual Approach
PublicationIn the paper we present the results of experiment we performed to determine whether a contextual approach may be used to increase the performance of querying a knowledge base. For the experiments we have used a unique setting where we put much effort in developing a contextual and a non-contextual ontology which are as much close counterparts as possible. To achieve this we created a contextual version...
-
Comprehensive Comparison of a Few Variants of Cluster Analysis as Data Mining Tool in Supporting Environmental Management
PublicationA few variants of hierarchical cluster analysis (CA) as tool of assessment of multidimensional similarity in environmental dataset are compared. The dataset consisted of analytical results of determination of metals (Na, K, Ca, Sc, Fe, Co, Zn, As, Br, Rb, Mo, Sb, Cs, Ba, La, Ce, Sm, Hf and Th) in ambient air dried and kept alive, by the means of hydroponics, moss baskets collected in 12 locations on the area of Tricity (Poland)....
-
Scalable Maintenance of Address Mapping and Autodetecion in Environments Where Agents are Uncapable of Self-Registration
PublicationWhen working with multi-agent systems it is often desirable to manage the agent set. The existing methods of central monitoring stems from two different fields of application. The first has its roots in in computer network monitoring, the other in mutli-agent simulation environments. Both approaches are not general enough to cater for loosely controlled environments, where the total agent population is not known and often fluctuating,...
-
Analysing By-Products Interaction as an Industry Resource of Circular Economy in Ukraine and the World
PublicationThe paper analyses existing and current scientific developments and literature sources, which show the advantages and disadvantages of many different influences of waste in Ukraine and other countries of Europe and the world. As a research result, stable connections have been established between the factors and criteria in assessing the by-product interaction as an industry resource. In our research, we used programs R.Studio and...
-
Design of Cost-Efficient Optical Fronthaul for 5G/6G Networks: An Optimization Perspective
PublicationCurrently, 5G and the forthcoming 6G mobile communication systems are the most promising cellular generations expected to beat the growing hunger for bandwidth and enable the fully connected world presented by the Internet of Everything (IoE). The cloud radio access network (CRAN) has been proposed as a promising architecture for meeting the needs and goals of 5G/6G (5G and beyond) networks. Nevertheless, the provisioning of cost-efficient...
-
Biocompatibility and bioactivity of bearing loaded metallic implants
PublicationPresentation of developed titanium alloy base composite materials possessing better biocompatibility, longer lifetime and bioactivity behavior for bearing loaded implants, e.g. hip joint and knee joint endoproshtesis.
-
The Thin-Layer Microchromatography (μTLC) and TLC–FID Technique as a New Methodology in the Study of Lubricating Oils
PublicationThis paper concerns the possibility of using TLC coupled with a flame ionization detector (FID) and micro-TLC (μTLC) as precursors for microfluidized devices of analytical techniques to identify and determine the presence and content of the petroleum/vegetable oil base in the lubricating oils applied in cutting devices (chainsaws). This research is related to the problem of ensuring, in compliance with the requirements of environmental...
-
Measurement of temperature-dependent viscosity and thermal conductivity of alumina and titania thermal oil nanofluids
PublicationThe results of simultaneous measurements of dynamic viscosity, thermal conductivity, electrical conductivity and pH of two nanofluids, i.e. thermal oil/Al2O3 and thermal oil/TiO2 are presented. Thermal oil was selected as a base liquid because of possible application in ORC systems as an intermediate heating agent. Nanoparticles were tested at the concentration of 0.1%, 1% and 5% by weight within temperature range from 20°C to...
-
Extending Expressiveness of Knowledge Description with Contextual Approach
PublicationIn the paper we show how imposing the contextual structure of a knowledge base can lead to extending its expressiveness without changing the underlying language. We show this using the example of Description Logics, which constitutes a base for a range of dialects for expressing knowledge in ontologies (including state-of-the-art OWL). While the contextual frameworks have been used in knowledge bases, they have been perceived as...
-
Resilience of 5G Mobile Communication Systems to Massive Disruptions
PublicationThis chapter discusses vital techniques to enhance the resilience of 5G systems. It starts with dependability assessment of 5G networks. Next, it describes (a) the frequency fallback technique to improve availability and survivability of 5G services, (b) segment interleaving scheme to enhance communications resilience between base stations and the remaining part of the network and (c) multi-operator protection to address the resilience...
-
Estimation of Stresses in a Dry Sand Layer Tested on Shaking Table
PublicationTheoretical analysis of shaking table experiments, simulating earthquake response of a dry sand layer, is presented. The aim of such experiments is to study seismic-induced compaction of soil and resulting settlements. In order to determine the soil compaction, the cyclic stresses and strains should be calculated first. These stresses are caused by the cyclic horizontal acceleration at the base of soil layer, so it is important...
-
How to enhance perception of reassembled but incomplete works of ancient art? Eye-tracking study of virtual anastylosis.
Publicationn 1964 the Venice Charter described anastylosis as the only acceptable method of reassembly of architectural remains. Although the scientific community has agreed with the Charter’s decision, many questions pertaining to the technical and aesthetic aspects of anastylosis remain unanswered. Virtual anastylosis seems one of the most promising digital solutions to finding at least some answers, as it permits testing various solutions...
-
Artificial neural network prophecy of ion exchange process for Cu (II) eradication from acid mine drainage
PublicationThe removal of heavy metal ions from wastewater was found to be significant when the cation exchange procedure was used effectively. The model of the cation exchange process was built using an artificial neural network (ANN). The acid mine drainage waste’s Cu(II) ion was removed using Indion 730 cation exchange resin. Experimental data from 252 cycles were recorded. In a column study, 252 experimental observations validated the...
-
A bound on the number of middle-stage crossbars in f-cast rearrangeable Clos networks
PublicationIn 2006 Chen and Hwang gave a necessary and sufficient condition under which a three-stage Clos network is rearrangeable for broadcast connections. Assuming that only crossbars of the first stage have no fan-out property, we give similar conditions for f-cast Clos networks, where f is an arbitrary but fixed invariant of the network. Such assumptions are valid for some practical switching systems, e.g. high-speed crossconnects....
-
The central server of the Border Guard's distributed multimedia system for monitoring and visualisation of ongoing and archival events
PublicationThe paper presents the architecture and functionalities of the central server (CENTER) of the distributed system for the Polish Border Guard (BG) for monitoring maritime areas. The overall system has been extended to incorporate, apart from map data, also different multimedia elements such as video from cameras or audio from telephone connections operated by BG units. This requires new system elements: Archive Servers for storing...
-
The concept of knowledge bases supporting the it systems integration model
PublicationThis paper presents main concepts regarding the design of a knowledge base in order to support IT systems integration. The main goal of the research is to develop a universal method of integration of various systems concerning any possible area of interest. The concept is based on creating a generic mechanism which would support the decision regarding the choice of the integration model. The most important tasks include: key factors...
-
MEASUREMENT OF TEMPERATURE-DEPENDENT VISCOSITY AND THERMAL CONDUCTIVITY OF ALUMINA AND TITANIA THERMAL OIL NANOFLUIDS
PublicationIn this study results of simultaneous measurements of dynamic viscosity, thermal conductivity, electrical conductivity and pH of two nanofluids, i.e. thermal oil/Al2O3 and thermal oil/TiO2 are presented. Thermal oil is selected as a base liquid because of possible application in ORC systems as an intermediate heating agent. Nanoparticles were tested at the concentration of 0.1%, 1% and 5% by weight within temperature range from...
-
Harmonic Vibrations of Nanosized Magnetoelectric Bodies with Coupled Surface and Interphase Effects: Mathematical Models and Finite Element Approaches
PublicationThe harmonic problems for piezomagnetoelectric nanosized bodies with taking into account the coupled damping and surface effects are considered on the base of the generalized Gurtin-Murdoch model. In the development of previous investigations, the coupled mechanical, electric and magnetic surface effects with surface inertial terms are introduced into the model. For a homogeneous model, the composite material is considered as homogeneous...
-
Mechanical Properties of Aluminium Bracket Strengthening
PublicationThe aim of the research is laboratory investigation of aluminium brackets employed to fasten lightweight curtain walls to building facilities. Tensile loads perpendicular to end plates (vertical) were applied here. The author focused on the solutions intended to increase the load-carrying capacity of aluminium brackets applying the plain washer form A (DIN 125; ISO 7089), plain washer with an outer diameter about 3d (DIN 9021;...
-
The New LM-PCR/Shifter Method for the Genotyping of Microorganisms Based on the Use of a Class IIS Restriction Enzyme and Ligation Mediated PCR
PublicationThis study details and examines a novel Ligation-Mediated - Polymerase Chain Reaction (LM-PCR) method. Named the LM-PCR/Shifter, it relies on the use of a Class IIS restriction enzyme giving restriction fragments with different 4 base, 5' overhangs, this being the Shifter, and the ligation of appropriate oligonucleotide adapters. A sequence of 4-base, 5' overhangs of the adapter and a 4-base sequence of the 3' end of the primer(s)...
-
Bitumen-Based Poroelastic Pavements: Successful Improvements and Remaining Issues
PublicationThis article presents the development process of designing and testing poroelastic pavement based on highly polymer-modified bitumen. Poroelastic wearing course was composed of mineral and rubber aggregate mixed with highly polymer-modified bitumen, in contrast to previous trials, during which polyurethane resins were mainly used as binder, which led to several serious technological problems concerning difficult production, insufficient...
-
System of innovation: a sectoral approach
Publicationthe article presents a systems approach to innovation as an alternative method of assessing the sector innovativeness. in the article the building blocks of each sectoral system of innovations (ssi) such as a knowledge base, institutions and actors are discussed. moreover, the five models of ssi are presented.
-
Special Issue: “Non-Destructive Testing of Structures”
PublicationThe Special Issue “Non-Destructive Testing of Structures” has been proposed to present recent developments in the field of diagnostics of structural materials and components in civil and mechanical engineering. The papers highlighted in this editorial concern various aspects of non-invasive diagnostics, including such topics as condition assessments of civil and mechanical structures and connections of structural elements, the...
-
A framework for accelerated optimization of antennas using design database and initial parameter set estimation
PublicationThe purpose of this paper is to exploit a database of pre-existing designs to accelerate parametric optimization of antenna structures is investigated. Design/methodology/approach The usefulness of pre-existing designs for rapid design of antennas is investigated. The proposed approach exploits the database existing antenna base designs to determine a good starting point for structure optimization and its response sensitivities....
-
Generowanie modeli symulacyjnych na potrzeby systemu ekspertowego wspomagającego projektowanie układów automatyki statku
PublicationOmówiono automatyczne generowanie modeli symulacyjnych na potrzeby systemu ekspertowego wspomagającego projektowanie układów automatyki statków. Na podstawie przyjętych założeń projektowych system ekspertowy zleca badania wybranych struktur podsystemów elektroenergetycznych statków. Aplikacja symulacyjna pobiera z biblioteki modele matematyczne elementów składowych struktur, a następnie zestawia modele symulacyjne, wykonuje badania...
-
Evaluation of foundation input motions based on kinematic interaction models
PublicationThe present study was designed to demonstrate the importance of base-slab averaging and embedment effects on the foundation-level input motions due to earthquake excitations. Evaluation of foundation-level input motions based on the most commonly adopted kinematic interaction models are presented. In order to conduct this investigation, original records of horizontal accelerations for two case-study buildings were utilized. Computed...
-
Common methods for the chiral determination of amphetamine and related compounds I. Gas, liquid and thin-layer chromatography
PublicationThis article reviews the most common, useful methods for the chiral determination of amphetamine (AM) and AM-deriveddesigner drugs in different of matrix, including blood, hair, urine, medicaments or standard solutions, taking into considerationarticles published in the past 15 years. We consider chromatographic methods (e.g., gas, liquid, high-performance liquid, and thinlayer). We describe several types of chiral derivatization...
-
Direct chromatographic methods in the context of green analytical chemistry
PublicationWe review analytical protocols based on gas and liquid chromatography (GC and LC), but involving no sample preparation.Green analytical chemistry seeks to minimize negative impacts of analytical chemistry. Direct analytical methods ideally fulfillthis requirement, as they preclude sample preparation - the most polluting step of the analytical procedure.We describe examples of GC methodologies for environmental and food analysis...
-
Sensitivity analysis of critical loads of I-columns
PublicationThe first order variation of critical buckling load of thin-walled columns with bisymmetric open cross-section due to some variations of the design variables such as: cross-section dimensions, or material characteristics is derived. The influence of the residual welding stresses is taken into account. In the numerical examples dealing with I-column the functions describing the effect of the variation of the dimensions of the flange...
-
Dynamics of mechanical model of implant-tissue system in ventral hernia repair
PublicationThe paper deals with a finite element modelling of implants in the problem of ventral hernia repair. The synthetic mesh implanted in the abdomen during surgery is here modelled as a membrane structure. Thesystem undergoes the internal abdominal pressure that occurs during the postoperative cough, the load identified in the literature as the main cause of the connection failure and hernia recurrence. The model can be used to estimate...