Filters
total: 745
filtered: 599
Search results for: slowly biodegradable substrate
-
Characterization of glucoamylase immobilized on magnetic nanoparticles
PublicationMagnetic support was prepared by precipitation from an alkaline solution of divalent and trivalent iron ions and subsequently was modified with 3-aminopropyltriethoxysilane. FTIR analysis showed existence of a new Si-O-Fe bond in obtained particles. Scanning electronic microscopy images shows that the nanoparticles of all samples have particle size below 30 nm. Glucoamylase AMG 300L was immobilized onto the modified magnetic support...
-
Seeding enhancement for microcrystaline diamond layers growth on non-diamond substrates
PublicationThe present paper gives an overview on the possible methods of seeding substrates for diamond layers growth. Diamond in reason of his properties is very desirable material in microelectronic, biomedical and waste treatment sensors. Microcrystalline diamond for these applications must be grown on silicon substrate in microwave plasma assisted chemical vapor deposition (MPACVD). To grow diamond on non-diamond surface pre-growth...
-
Study of Nanohydroxyapatite Coatings Prepared by the Electrophoretic Deposition Method at Various Voltage and Time Parameters
PublicationThe aim of the work is to compare the properties of nanohydroxyapatite coatings obtained using the electrophoretic deposition method (EDP) at 10 V, 20 V, and 30 V, and with deposit times of 2 and 5 min. The primary sedimentation was used to minimize the risk of the formation of particle agglomerates on the sample surface. Evaluation of the coating was performed by using a Scanning Electron Microscope (SEM), Energy-Dispersive Spectroscopy...
-
Low-strain sensor based on the flexible boron-doped diamond-polymer structures
PublicationA free-standing high boron-doped diamond nanosheet (BDDNS) has been fabricated for the development of a flexible BDDNS strain senor. High boron-doped diamond was initially grown on a tantalum substrate in a microwave plasma-assisted chemical vapor deposition method, and was then transferred to a Kapton polymer substrate to fabricate the flexible BDDNS/Kapton device. Before performing the transfer process, the thin BDDNS’s morphology...
-
Design and Optimization of Metamaterial-Based 5G Millimeter Wave Antenna for Gain Enhancement
PublicationIn this brief, a low profile, broadband, high-gain antenna array based on optimized metamaterials (MMs) with dual-beam radiation is reported for 5G millimeters wave (mm-wave) applications. The design is a simple bow tie operating at a 5G band of 28 GHz. It consists of two bow ties with substrate integrated waveguide (SIW)-based power splitter. A broad impedance bandwidth of 26.3−29.8 GHz is obtained by appropriately combining the...
-
Bioactive core material for porous load-bearing implants
PublicationSo far state of knowledge on biodegradable materials is reviewed. Among a variety of investigated materials, those composed of polymers and ceramics may be considered as only candidates for a core material in porous titanium alloy. The collagen and chitosan among natural polymers, polyhydroxy acids among synthetic polymers, and hydroxyapatite and tricalcium phosphate among ceramics are proposed for further research. Three essential...
-
Molecularly imprinted polymers based on deep eutectic solvents as a greenest materials for selective extraction of emerging contaminants from complex samples
PublicationSome of the reagents applied in the synthesis of molecularly imprinted polymers (MIPs) may impact on health and the environment. Thus, a new generation of promising green chemicals are nowadays introduced and investigated, including deep eutectic solvents (DESs). DESs seems to be a reasonable choice as they are characterized as non-toxic, low cost, easy to prepare and biodegradable chemicals. This review presents the information...
-
Deep Eutectic Solvents and Their Uses for Air Purification
PublicationChemical compounds released into the air by the activities of industrial plants and emitted from many other sources, including in households (paints, waxes, cosmetics, disinfectants, plastic (PVC) flooring), may affect the environment and human health. Thus, air purification is an important issue in the context of caring for the condition of the environment. Deep eutectic solvents (DESs) as liquids with environmentally friendly...
-
FEM approach to estimate the behaviour of biocomposite metal-surface coating system
PublicationA three dimensional (3D) model of biocomposite metal-surface coating system, which is influenced byknown external forces, is proposed. This model consists of the metallic substrate (Ti6Al4V) and thehydroxyapatite (HA) coating. Using FEM (finite element method), strain-stress maps of model weregenerated for investigating relations between the extreme stress of HA coating and the magnitude ofexternal force and the thickness of the...
-
Hybrid biobateryy based on arylated carbon nanotubes and laccase
PublicationSingle-walled carbon nanotubes (SWCNT) were covalently modified with antracene and antraquinone and used for the construction of cathodes for biocatalytic reduction od dioxygen. The nanotubes with aromatic groups casted onto the electrode increased the working surface of the electrode and enabled efficient direct electron tarnsfer (DET) between the enzyme and the electrode. the aryl groups enter the hydrophobic pocket of the T1...
-
An Analysis of Probe-Fed Rectangular Patch Antennas With Multilayer and Multipatch Configurations on Cylindrical Surfaces
PublicationA multi-patch configuration of probe-fed rectangular microstrip antennas mounted on a cylindrical body, with electrically small radius, with an arbitrary number of substrate and superstrate layers is investigated in this paper. A full-wave analysis and a moment-method calculation are employed. A unified procedure for creating proper matrices for the investigated geometry of the structure is outlined here. Numerical results for...
-
Review of the Application of Graphene-Based Coatings as Anticorrosion Layers
PublicationDue to the excellent properties of graphene, including flexibility that allows it to adjust to the curvature of the substrate surface, chemical inertness, and impermeability, graphene is used as an anticorrosion layer. In this review, we present the current state-of-the-art in the application of graphene in the field of protective coatings. This review provides detailed discussions about the protective properties of graphene coatings...
-
Physical properties of homogeneous TiO2 films prepared by high power impulse magnetron sputtering as a function of crystallographic phase and nanostructure
PublicationOptical, photo-electrochemical, crystallographic and morphological properties of TiO2 thin films prepared by high power impulse magnetron sputtering at low substrate temperatures (<65 ◦C) without post-deposition thermal annealing are studied. The film composition-anatase, rutile or amorphous TiO2-is adjusted by the pressure (p ∼ 0.75-15 Pa) in the deposition chamber. The different crystallographic phases were determined with grazing...
-
Design and Optimization of Metamaterial-based Highly-isolated MIMO Antenna with High Gain and Beam Tilting Ability for 5G Millimeter Wave Applications
PublicationThis paper presents a wideband multiple-input multiple-output (MIMO) antenna with high gain and isolation, as well as beam tilting capability, for 5G millimeter wave (MMW) applications. A single bow-tie antenna fed by a substrate-integrated waveguide (SIW) is proposed to cover the 28 GHz band (26.5–29.5 GHz) with a maximum gain of 6.35 dB. To enhance the gain, H-shaped metamaterial (MM)-based components are incorporated into the...
-
Endothelial dysfunction due to eNOS uncoupling: molecular mechanisms as potential therapeutic targets
PublicationNitric oxide (NO) is one of the most important molecules released by endothelial cells, and its antiatherogenic properties support cardiovascular homeostasis. Diminished NO bioavailability is a common hallmark of endothelial dysfunction underlying the patho‑ genesis of the cardiovascular disease. Vascular NO is synthesized by endothelial nitric oxide synthase (eNOS) from the substrate L‑arginine (L‑Arg), with tetrahydrobiopterin...
-
Nanostructuring of thin Au films deposited on ordered Ti templates for applications in SERS
PublicationIn this work the results on thermal nanostructuring of the Au films on Ti templates as well as morphology and optical properties of the obtained structures are reported. The bimetal nanostructures are fabricated in a multi-step process. First, the titania nanotubes are produced on the surface of Ti foil by anodization in an ethylene glycol-water solution containing fluoride ions. This is followed by chemical etching in oxalic acid...
-
Polymerization of chloro-p-xylylenes, quantum-chemical study
PublicationThe p-xylylene monomers of parylene N, C and D have similar high polymerization reactivity. For effective copolymerization processes this fact is basically a draw- back and for instance the copolymerization with styrene doesn't go at all (Corley et al. J Pol Sc 13(68):137156, 1954). Substitution of terminal hydrogen atoms by chlorine atoms reduces reactivity dramatically. 7,7,8,8-tetrachloro-p- xylylene and 2,5,7,7,8,8-hexachloro-p-xylylene...
-
Unexpected Z/E isomerism of N-methyl-O-phosphothioyl benzohydroxamic acids, their oxyphilic reactivity and inertness to amines
PublicationThiophosphinoylation of N-methyl p-substituted benzohydroxamic acids using disulfanes (method A) or diphenylphosphinothioyl chloride (method B) provides only one conformer of the respective O-phosphothioyl derivative (Xray and NMR analysis). Undergoing the P-transamidoxylation reaction is an evidence of the reversibility of thiophosphinoylation. Only those products containing strong EWG substituents in the aroyl residue or bulky...
-
Improvement of electrochemical action of zinc-rich paints by addition of nanoparticulate zinc
PublicationThe influence of nanosized particles on electrochemical action of standard zinc-rich paints by means of SEM as well as potential and impedance measurements has been investigated. The motivation for doing this was to obtain additional electrical connection between the spherical microparticles themselves and zinc particles and steel substrate. Overall zinc content was at the level of 92% by weight. Samples with different concentration...
-
Properties of chitosan/CuNPs coatings electrophoretically deposited on TiO2 nanotubular oxide layer of Ti13Zr13Nb alloy
PublicationCoatings based on chitosan/CuNPs (chit/CuNPs) were obtained by a one-step electrophoretic deposition (EPD) on nanotubular oxide layer of Ti13Zr13Nb alloy. The deposition was carried out for 1 min applying voltages of 10 and 20 V with and without the addition of dispersing agent (Polysorbate 20) to the suspension. The coatings obtained for the lower voltage were more uniform than for the higher voltage. By adding a dispersing agent,...
-
Anti-plane waves in an elastic thin strip with surface energy
PublicationWe consider anti-plane motions of an elastic plate taking into account surface energy within the linear Gurtin–Murdoch surface elasticity. Two boundary-value problems are considered that describe complete shear dynamics of a plate with free faces or with free and clamped faces, respectively. These problems correspond to anti-plane dynamics of an elastic film perfectly or non-perfectly attached to a rigid substrate. Detailed analysis...
-
Novel Coplanar-Strip-Based Excitation Technique for Design of Broadband Circularly Polarization Antennas with Wide 3-dB Axial Ratio Beamwidth
PublicationIn this paper, a novel excitation technique for design of a single-point-fed compact low-profile wide-slot antennas with broadband circular polarization (CP) and wide 3 dB axial ratio (AR) beamwidth is presented. Two inverted L-shape parasitic strips placed coplanar to the microstrip line of an asymmetric CPW, and a horizontal strip that protrudes from the vertical edge of the backside ground plane of the substrate are used for...
-
Possibilities of Leachate Co-Treatment Originating from Biogas Production in the Deammonification Process
PublicationIn the methane fermentation process, sewage sludge is the single substrate or serves as a co-substrate with the addition of various waste products. After the treatment stable digestate is obtained, which consists of two phases solid and liquid. Liquid phase, called as a leachate, due to the high content of nutrients must be treated before they are discharged into the final receiver. Physical and chemical methods of leachate treatment...
-
Protective properties of Al2O3 + TiO2 coating produced by the electrostatic spray deposition method
PublicationMechanical resistance of Al2O3 + TiO2 nanocomposite ceramic coating deposited by electrostatic spray deposition method onto X10CrAlSi18 steel to thermal and slurry tests was investigated. The coating was produced from colloidal suspension of TiO2 nanoparticles dispersed in 3 wt% solution of Al2(NO3)3, as Al2O3 precursor, in ethanol. TiO2 nanoparticles of two sizes, 15 nm and 32 nm, were used in the experiments. After deposition,...
-
Myrosinase activity in different plant samples; optimisation of measurement conditions for spectrophotometric and pH-stat methods
PublicationMyrosinase found in Brassicaceae plants, is the enzyme responsible for hydrolysis of glucosinolates. As a result a variety of biologically active metabolites are liberated, whose importance in crop protection and especially in cancer chemoprevention is rapidly gaining recognition. The growing practical application of glucosinolate degradation products requires that sensitive and reliable methods of myrosinase activity determination...
-
Partitioning of heavy metals in sub-surface flow treatment wetlands receiving high-strength wastewater
PublicationThe retention of heavy metals at two pilot-scale treatment wetlands (TWs), consisting of two vertical flow beds (VSSF) followed by a horizontal flow bed (HSSF) was studied. The TWs received highstrength wastewater: reject waters from sewage sludge centrifugation (RW) and landfill leachate (LL). The concentrations of metals: Fe, Mn, Zn, Al, Pb, Cu, Cd, Co, Ni were measured in treated wastewater, substrate of the beds and in plant...
-
New Complementary Resonator for Permittivity- and Thickness-Based Dielectric Characterization
PublicationThe design of high-performance complementary meta-resonators for microwave sensors featur-ing high sensitivity and consistent evaluation of dielectric materials is challenging. This paper presents the design and implementation of a novel complementary resonator with high sensi-tivity for dielectric substrate characterization based on permittivity and thickness. A comple-mentary crossed arrow resonator (CCAR) is proposed and integrated...
-
High gain/bandwidth off‑chip antenna loaded with metamaterial unit‑cell impedance matching circuit for sub‑terahertz near‑field electronic systems
PublicationAn innovative off-chip antenna (OCA) is presented that exhibits high gain and efficiency performance at the terahertz (THz) band and has a wide operational bandwidth. The proposed OCA is implemented on stacked silicon layers and consists of an open circuit meandering line. It is shown that by loading the antenna with an array of subwavelength circular dielectric slots and terminating it with a metamaterial unit cell, its impedance...
-
Influence of Phosphorus Speciation on Its Chemical Removal from Reject Water from Dewatering of Municipal Sewage Sludge
PublicationThe aim of the presented research was the assessment of phosphorus speciation impact on the precipitation of phosphorus in reject water using Ca(OH)2. To achieve this, phosphorus speciation (organic and inorganic phosphorus in suspension and in dissolved form) in reject water that is produced during sludge dewatering, after methane digestion in wastewater treatment plants (WWTPs), was determined. This study covered the materials...
-
A Highly Sensitive Planar Microwave Sensor for Detecting Direction and Angle of Rotation
PublicationThis article presents a technique based on a modified complementary split-ring resonator (CSRR) to detect angular displacement and direction of rotation with high resolution and sensitivity over a wide dynamic range. The proposed microwave planar sensor takes advantage of the asymmetry of the sensor geometry and measures the angle of rotation in terms of the change in the relative phase of the reflection coefficients. The sensor...
-
Planetary roller extruders in the sustainable development of polymer blends and composites – Past, present and future
PublicationScrew extruders as continuous flow reactors allow the synthesis of new polymers, preparation of polymer blends and composites, and modification or functionalization of commercially available polymers. Literature data shows that the twin screw extrusion is the most popular solution used for this purpose. In contrast, the number of scientific papers on alternative methods, such as multi-screw extruders, is somewhat limited. This...
-
Alginate-based sorbents in miniaturized solid phase extraction techniques - Step towards greenness sample preparation
PublicationIn response to growing concerns about environmental degradation, one of the main areas of research activity in recent years has been to make sample preparation methods more sustainable and eco-friendly. The increasing greenness of this step can be achieved by minimizing the usage of reagents, automating individual stages, saving energy and time, and using non-toxic, biodegradable substances. Therefore, the use of natural materials...
-
Reclaimed Rubber/Poly(ε‐caprolactone) Blends: Structure, Mechanical, and Thermal Properties
PublicationThe amount of elastomeric waste, especially from tires is constantly increasing on a global scale. The recycling of these residua should be considered a priority. Compounding the waste rubbers with other polymers can be an excellent alternative to reuse waste materials. This procedure requires solving the issue of the lack of compatibility between the waste rubber particles and other polymers. Simultaneously, there is a claim for...
-
Evaluation and start-up of an electro-Fenton-sequencing batch reactor for dairy wastewater treatment
PublicationThis study examined the performance of an integrated wastewater (WW) treatment system, namely an electro-Fenton (EF)-sequencing batch reactor (SBR), for dairy industry WW. The EF process was used as the first stage of the SBR. It degrades bio-refractory compounds via advanced oxidation processes, thereby resulting in the formation of simple biodegradable intermediates. Several factors, including the hydraulic retention time (HRT),...
-
Structural changes of bacterial cellulose due to incubation in conditions simulating human plasma in the presence of selected pathogens
PublicationBacterial nanocellulose (BNC) is a natural biomaterial with a wide range of medical applications. However, it cannot be used as a biological implant of the circulatory system without checking whether it is biodegradable under human plasma conditions. This work aimed to investigate the BNC biodegradation by selected pathogens under conditions simulating human plasma. The BNC was incubated in simulated biological fluids with or...
-
Curing epoxy resin with anhydride in the presence of halloysite nanotubes: the contradictory effects of filler concentration
PublicationEpoxy resins can be cured with a wide variety of curing agents such as amines and anhydrides, but anhydride curing would be more favorable for research purpose because of epoxy-anhydride curing taking place slowly at room temperature. Incorporation of natural nanosized minerals into epoxy is of environmental importance. Halloysite nanotubes (HNTs) display chemical properties similar to those of silica and alumina, and hydroxyl...
-
The effect of high pressure on formation of volatile amines in minced meat of cod (Gadus morhua)
PublicationThe effects of high pressure at subzero temperature (193 MPa, at −20 °C) on inactivation of natural microflora of cod meat and degradation of trimethylamine oxide (TMAO) to trimethylamine (TMA) during refrigerated storage and to dimethylamine (DMA) and formaldehyde (FA) during frozen storage were investigated. The content of TMA, DMA and FA in cod meat did not change immediately after pressure treatment. During 40 days of frozen...
-
Zastosowanie programu SCA w badaniu zakłóceń sprzężenia podłożowego w układach scalonych CMOS
PublicationW pracy przedstawiono charakterystykę programu SCA (Substrate Coupling Analysis), który służy do generowania impedancyjnego modelu podłoża układu scalonego na podstawie danych topografii układu oraz parametrów technologii. Format danych wejściowych oraz model podłoża zaprezentowano na przykładzie układu inwertera CMOS. Przedstawiono również wyniki symulacji mieszanego układu scalonego: dzielnik częstotliwości i analogowe źródło...
-
Assessment of copper surface coverage with corrosion inhibitor using AFM-based local electrical measurements
PublicationThe paper presents a new method of assessment of metal surface coverage with corrosion inhibitor and thus of inhibitor protective performance. It is based on the atomic force microscopy measurement performed in a contact mode. Apart from topography images the proposed approach allows acquisition of local DC maps and local electrical impedance spectra via application of DC bias voltage or AC perturbation signal between the conductive...
-
Modyfikacja cementu kostnego w celu uzyskania długotrwałej ochrony antybakteryjnej
PublicationNiniejsza rozprawa doktorska stanowi przewodnik po jednotematycznym cyklu publikacji, dotyczącym modyfikacji akrylowego cementu kostnego celem uzyskania długotrwałej i efektywnej ochrony antybakteryjnej. W ramach niego przeprowadzono badania eksperymentalne polegające na opracowaniu technologii wytwarzania modyfikowanego cementu kostnego oraz procedury medycznej jego stosowania. Cement kostny był modyfikowany przez zastosowanie...
-
Influence of silver nanoparticles addition on antibacterial properties of PEO coatings formed on magnesium
PublicationMagnesium is a biodegradable material and thus could be a choice for bone fixation devices and implants with a specific purpose. This study aims to enhance the anti-corrosive, biocompatible, and antibacterial properties on magnesium-based materials through ceramic coatings formation. To achieve this the silicate-based electrolyte was used to create of Plasma Electrolytic Oxidation (PEO) coatings. During investigation the bioactive...
-
In-Situ Processing of Biocomposites via Reactive Extrusion
PublicationLaw regulations, economic and environmental factors are the main causes for the rapidly growing interests in biocomposites’ research, conducted currently in a number of academic and industrial scientific centers. However, weak polymer matrix/filler interactions, common in biocomposites, result in unsatisfactory mechanical properties, which limit their practical applications. From many attempts performed to solve this problem, in-situ...
-
Alternative Methods of Preparation of Soluble Keratin from Chicken Feathers
PublicationHuge amount of keratinous waste, especially birds’ feathers, demands more value-added application instead of dumping. The present work reports the results of experiments aimed at preparing soluble keratin useful for novel bioproduct formation. The effect of thermo-chemical treatments with various reducing agents, i.e. 2-mercaptoethanol, dithiothreitol, sodium m-bisulphite, and sodium bisulphite, as well as sodium hydroxide, on...
-
Bacterial consortium an axenic cultures isolated from activated sewage sludge for biodegradation of imidazolium-based ionic liquid
PublicationExtensive research and increasing number of potential industrial applications made ionic liquids (ILs) important materials in design of new, cleaner technologies. Together with the technological applicability, the environmental fate of these chemicals is considered and significant efforts are being made in designing strategies to mitigate their potential negative impacts. Many ILs are proven to be poorly biodegradable and relatively...
-
Gelatin-Modified Polyurethanes for Soft Tissue Scaffold
PublicationRecently, in the field of biomaterials, which are being designed for soft tissue scaffolding, is growing the interest of their modification with natural polymers. Synthetic polymers are often hard, not easy to process and they do not possess fine biodegradable profile. From the other hand natural polymers are biocompatible, but weak when used alone. The combination of natural and synthetic polymers gives the suitable properties...
-
Beam on elastic foundation with anticlastic curvature: Application to analysis of mode I fracture tests
PublicationA first order correction is proposed taking into account both interface elasticity and transverse anticlastic curvature of flexible substrate(s) in the DCB (and related tests). Adherends are represented by Kirchhoff-Love plates, and the interface by Winkler-type elastic foundation. Two functions are introduced, representing evolution of beam deflection along the sample midline and anticlastic curvature along the plate. A method...
-
Microwave Ring Resonator Based Pressure Sensor
PublicationThis paper demonstrates a microwave pressure sensor, which is based on microstrip line-fed ring resonators. The first ring resonator is loaded with the concentric cylindrical shafts, while the same number of the hollow shanks as the shafts are mounted on the second ring resonator. The arrangement of the cylindrical shaft and hollow shank allows for mechanical movement between two substrates while maintaining electrical contact....
-
IN VITRO PROPAGATION OF RHODODENDRON TOMENTOSUM - AN ENDANGERED ESSENTIAL OIL BEARING PLANT FROM PEATLAND
PublicationRhododendron tomentosum Harmaja (formerly Ledum palustre L.) is a medicinal peat bog plant native to northern Europe, Asia and North America. This plant has a distinctive aroma thanks to the presence of essential oil, to which it also owes its anti-inflammatory, analgesic, antimicrobial and insecticidal properties. However, in Europe R. tomentosum is classified as an endangered species, mainly due to degradation of peatlands. In...
-
Two bacterial small heat shock proteins, IbpA and IbpB, form a functional heterodimer
PublicationSmall heat shock proteins (sHsps) are a conserved class of ATP-independent chaperones which in stress conditions bind to unfolded protein substrates and prevent their irreversible aggregation. Substrates trapped in sHsps-containing aggregates are efficiently refolded into native structures by ATP-dependent Hsp70 and Hsp100 chaperones. Most γ-proteobacteria possess a single sHsp (IbpA), while in a subset of Enterobacterales, as...
-
Effects of Micro-Arc Oxidation Process Parameters on Characteristics of Calcium-Phosphate Containing Oxide Layers on the Selective Laser Melted Ti13Zr13Nb Alloy
PublicationTitania-based films on selective laser melted Ti13Zr13Nb have been formed by micro-arc oxidation (MAO) at different process parameters (voltage, current, processing time) in order to evaluate the impact of MAO process parameters in calcium and phosphate (Ca + P) containing electrolyte on surface characteristic, early-stage bioactivity, nanomechanical properties, and adhesion between the oxide coatings and substrate. The surface...