displaying 1000 best results Help
Search results for: RAPID STATIC POSITIONING
-
Selected problems of sensitivity and reliability of a jack-up platform
PublicationThe paper deals with sensitivity and reliability applications to numerical studies of an off-shore platform model. Structural parameters and sea conditions are referred to the Baltic jack-up drilling platform. The study aims at the influence of particular basic variables on static and dynamic response as well as the probability of failure due to water waves and wind loads. The paper presents the sensitivity approach to a generalized...
-
Innovative Cold-formed GEB Section under Bending
PublicationThis paper is concerned with the numerical bending capacity study of the innovative cold-formed GEB sections. Both linear buckling analysis and non-linear static analysis incorporating geometric and material nonlinearity were carried out employing a shell structural model. The magnitudes of buckling load and limit load with respect to GEB section depth and thickness were obtained. The opened cold-formed section was tested assuming...
-
Load test of new European record holder in span length among extradosed type bridges
PublicationThe article presents acceptance load tests of a newly built extradosed MS-3 bridge located along the national road DK-16 near Ostróda (Poland). The structure features significant dimension in European reference scale. It is a new record holder in span length regarding this distinct bridge category. Its length ranges 206 m. Static and dynamic load tests were performed here. The program was extended by entire structural laser scanning...
-
OPTICAL STRAIN MEASUREMENT OF CONCRETE VERSUS MANUAL EXTENSOMETER MEASUREMENT BASED ON THE TEST RC DEEP BEAM IN A COMPLEX STATE OF STRESS
PublicationThe purpose of this study is to compare the strain measurement techniques of concrete in R-C element subjected to the monotonic load up to the failure. In the analysis manual extensometer methods of measurements and the optical system ARAMIS for non-contact three-dimensional measurements of deformation was used. The test sample was a cantilever deep beam loaded throughout the depth which was a part of the reinforced concrete deep...
-
Control of a vapour microturbine set in cogeneration applications
PublicationSystems with microturbines are implemented for local generation of heat and electricity. This paper presents the analysis of control concepts for a vapour microturbine set with a generator with permanent magnets, intended to work in small heat and power plants. Control system variants differed by the selection of controlled signals and set parameters. Possible ways of control were discussed and compared with experimentally determined...
-
Establishing Relationships between Parameters of the controlled Compaction Soil by Using Various In-Situ Tests
PublicationThe aim of research was evaluating reliable correlations between chosen soil parameters describing state of surface layers of soil. The paper presents site comparative tests based on the light falling weight deflectometer (LFWD), the static plate load tester (VSS), the dynamic probing light tester (DPL) and the bearing ratio tester (CBR in-situ) with relationships between soil state parameters. All featured in-situ...
-
Comparative Analysis of Two Polish Hyperbolic Systems AEGIR and JEMIOLUSZKA
PublicationGlobal Navigation Satellite System (GNSS) is seen by terrorists or hostile countries as a high value target. Volpe Center report contains the following statement: “During the course of its development for military use and more recent extension to many civilian uses, vulnerabilities of Global Navigation Satellite Systems (GNSS) – in the United States the Global Positioning System (GPS) – have become apparent. The vulnerabilities...
-
Measurements and Visualization of Sound Intensity Around the Human Head in Free Field Using Acoustic Vector Sensor
PublicationThis paper presents measurements and visualization of sound intensity around the human head simulator in a free field. A Cartesian robot, applied for precise positioning of the acoustic vector sensor, was used to measure sound intensity. Measurements were performed in a free field using a head and torso simulator and the setup consisting of four different loudspeaker configurations. The acoustic vector sensor was positioned around...
-
EVALUATION OF THE SEMIVARIOGRAM SELECTION ON THE KRIGING INTERPOLATION
PublicationThe aim of the paper is to present the possibilities of geostatistical interpolation kriging method using in the process of generating digital terrain models (DTM). The source of data is a direct measurements realized with a precision GNSS positioning kinematic measurement technique RTN. Kriging algorithm was analysed, especially in the meaning of a semivariogram every step. Theoretical semivariogram selection influence on the...
-
Methodology for the Correction of the Spatial Orientation Angles of the Unmanned Aerial Vehicle Using Real Time GNSS, a Shoreline Image and an Electronic Navigational Chart
PublicationUndoubtedly, Low-Altitude Unmanned Aerial Vehicles (UAVs) are becoming more common in marine applications. Equipped with a Global Navigation Satellite System (GNSS) Real-Time Kinematic (RTK) receiver for highly accurate positioning, they perform camera and Light Detection and Ranging (LiDAR) measurements. Unfortunately, these measurements may still be subject to large errors-mainly due to the inaccuracy of measurement of the optical...
-
Analiza statyczna i wytrzymałościowa konstrukcji wiszącej zadaszenia Stadionu Śląskiego
PublicationW artykule scharakteryzowano konstrukcję nośną zadaszenia Stadionu Śląskiego w Chorzowie, system statyczny i przyjęte rozwiązania konstrukcyjne. Przedstawiono poziom wytężenia kluczowych elementów oraz wytyczne dotyczące wzmocnienia. Analizy przeprowadzono w ramach audytu dokumentacji projektowej wykonanego na zlecenie inwestora.
-
Nonlinear free and forced vibrations of a dielectric elastomer-based microcantilever for atomic force microscopy
PublicationThe majority of atomic force microcode (AFM) probes work based on piezoelectric actuation. However, some undesirable phenomena such as creep and hysteresis may appear in the piezoelectric actuators that limit their applications. This paper proposes a novel AFM probe based on dielectric elastomer actuators (DEAs). The DE is modeled via the use of a hyperelastic Cosserat model. Size effects and geometric nonlinearity are included...
-
Numerical analysis of pile installation effects in cohesive soils
PublicationIn this thesis the empirical equation for radial effective stress calculation after displacement pile installation and following consolidation phase has been proposed. The equation is based on the numerical studies performed with Updated Lagrangian, Arbitrary Lagrangian-Eulerian and Coupled Eulerian-Lagrangian formulations as well as the calibration procedure with database containing world-wide 30 pile static loading tests in cohesive...
-
PROBLEMS WITH CORROSION PROTECTION STEEL STACKS IN FGD SYSTEMS
PublicationThis paper presents problems associated with corrosion of steel stacks and changes in philosophy of corrosion protection when implemented into flue gas desulphurization systems. In-situ tests were taken by means of electrochemical impedance spectroscopy at a stack which discharges flue gas before wet lime/limestone desulphurization. A very rapid soaking of spherical infill vinylester coating with electrolyte has been observed....
-
The Use of Electronic Nose for Sunflower and Rapeseed Oil Classification
PublicationThe electronic nose is an analytical device often used in food industries to examine the authenticity of their products. The use of the electronic nose allows for a rapid assessment of the quality of food. The oil samples from sunflower and rapeseed were used in this study. Both oil samples were kept inside the thermostat incubator at different ranging from 20oC to 180oC with increment of 40oC. Principal Component Analysis (PCA)...
-
The Use of Electronic Nose for Sunflower and Rapeseed Oil Classification
PublicationThe electronic nose is an analytical device often used in food industries to examine the authenticity of their products. The use of the electronic nose allows for a rapid assessment of the quality of food. The oil samples from sunflower and rapeseed were used in this study. Both oil samples were kept inside the thermostat incubator at different ranging from 20oC to 180oC with increment of 40oC. Principal Component Analysis (PCA)...
-
Mariusz Figurski prof. dr hab. inż.
PeopleMariusz Józef Figurski (born 27 April 1964 in Łasinie, Poland) - Polish geodesist, professor of technical sciences, professor at the Gdańsk University of Technology. Early life and education He passed the matriculation examination in 1983 after he had finished Jan III Sobieski High school in Grudziądz. He graduated the Military University of Technology on an individual mode at the Faculty of Electromechanics and Civil Engineering...
-
Peptidoglycan hydrolases - potential weapons against Staphylococcus aureus
PublicationBacteria of the genus Staphylococcus are common pathogens responsible for a broad spectrum of human and animal infections and belong to most important etiological factors causing food poisoning. Because of rapid increase in prevalence of isolation of staphylococci resistant to many antibiotics, there is an urgent need for development of new alternative chemotherapeutics. A number of studies have recently demonstrated the strong...
-
The evaluation of eGlasses eye tracking module as an extension for Scratch
PublicationIn this paper we present the possibility of using eGlasses eye tracking module as an extension for Scratch programming tool which is a visual programming language supporting computer skills learning. The main concept behind this project is to setup the interface for rapid interaction design. Eye tracking is a powerful tool for hands free communication but for that requires a dedicated software. This software is rarely tailored...
-
Analysis of server-side and client-side Web-GIS data processing methods on the example of JTS and JSTS using open data from OSM and geoportal
PublicationThe last decade has seen a rapid evolution of processing, analysis and visualization of freely available geographic data using Open Source Web-GIS. In the beginning, Web-based Geographic Information Systems employed a thick-client approach which required installation of platform-specific browser plugins. Later on, research focus shifted to platform-independent thin client solutions in which data processing and analysis was performed...
-
Inverse Modeling and Optimization of CSRR-based Microwave Sensors for Industrial Applications
PublicationDesign optimization of multivariable resonators is a challenging topic in the area of microwave sensors for industrial applications. This paper proposes a novel methodology for rapid re-design and parameter tuning of complementary split-ring resonators (CSRRs). Our approach involves inverse surrogate models established using pre-optimized resonator data as well as analytical correction techniques to enable rapid adjustment of geometry...
-
Simplified Numerical Model for Transient Flow of Slurries at Low Concentration
PublicationRapid transients are particularly dangerous in industrial hydro-transport systems, where solid-liquid mixtures are transported via long pressure pipelines. A mathematical description of such flow is difficult due to the complexity of phenomena and difficulties in determining parameters. The main aim of the study was to examine the influence of the simplified mixture density and wave celerity description on satisfactory reproduction...
-
Stability and load bearing capacity of a truss with elastic braces
PublicationThe present paper is devoted to the numerical and experimental investigations of stability of a truss stiffened by elastic braces. The model of a real roof truss scaled by factor ¼ was investigated. In the research the linear buckling and non-linear static analysis of the truss shell and beam model with geometric and material non-linearity is presented. The initial imperfections were assumed in the form of the first buckling mode....
-
On Configurability of Distributed Volunteer-Based Computing in the Comcute System
PublicationThe chapter proposes additional solutions that can be implemented within the Comcute system to increase its configurability. This refers to configuration of the reliability level in the W and S server layers, static or on-the-fly data partitioning and integration, configuration of the system for processing in the data streaming fashion, extending the system for selection of a project that the client wants to contribute to, ease...
-
Determination of Mathematical Model Parameters of a Medium Frequency Transformer
PublicationThe paper presents the results of experimental studies of the medium frequency transformer. The object of the research was a prototype of a single-phase transformer with a core made of ferrite I-core elements and windings made of Litz conductors. The research was carried out to determine the parameters of the transformer's mathematical model. The scope of the tests included determining the magnetic hysteresis loop and measuring...
-
Influence of stirrups in a concrete shell on strengthening reinforced concrete column
PublicationTwelve concrete columns, with a 150x150mm square section and three columns with a circular section (d=200mm), are tested to investigate the effect of strengthening by RC jacket. Based on a confined concrete model for axial static loading, an analytical methods, reported in the literature are proposed to predict the behavior of columns with RC jacket. The results support the conception that the effect of strengthening depends...
-
EvOLAP Graph – Evolution and OLAP-Aware Graph Data Model
PublicationThe objective of this paper is to propose a graph model that would be suitable for providing OLAP features on graph databases. The included features allow for a multidimensional and multilevel view on data and support analytical queries on operational and historical graph data. In contrast to many existing approaches tailored for static graphs, the paper addresses the issue for the changing graph schema. The model, named Evolution...
-
Analysis of the influence of geometrical imperfections on the equivalent load stabilizing roof truss with lateral bracing system
PublicationThe paper is focused on the numerical analysis of the stability and load bearing capacity of a flat steel truss. The structure was supported by elastic lateral braces. The translational and rotational brace stiffness was taken into account. The linear buckling analysis were performed for the beam and shell model of the truss. The nonlinear static analysis were conducted for the structure initial geometric imperfections. As a result...
-
Sharp transitions in low-number quantum dots Bayesian magnetometry
PublicationWe consider Bayesian estimate of static magnetic field, characterized by a prior Gaussian probability distribution, in systems of a few electron quantum dot spins interacting with infinite temperature spin environment via hyperfine interaction. Sudden transitions among optimal states and measurements are observed. Usefulness of measuring occupation levels is shown for all times of the evolution, together with the role of entanglement...
-
Active dynamic thermography method for TRAM flap blood perfusion mapping in breast reconstruction
PublicationThis paper presents the new method of the transverse rectus abdominis musculocutaneous flap blood perfusion mapping based on the active dynamic thermography. The method is aimed at aiding a surgeon during breast reconstruction procedure. A pair of dTnorm and t90_10 parameters were used as parametric image descriptors of the flap blood perfusion. The method was tested on 38 patients that were subjected to breast reconstruction procedure....
-
FEA analysis of the multicell piezoelectric motor
PublicationThe presented paper concerns a design, modeling and chosen tests of the prototype multicell piezoelectric motor (MPM). The principle of operation based on three independent traveling wave actuators is presented. The main materials and technologies used in the fabrication process are described. The structure of the motor is modeled using static and modal FEM analysis. The process of traveling wave generation in the MPM structure...
-
ZMIANY STRUKTURY DEMOGRAFICZNEJ LUDNOŚCI – WYZWANIA DLA RYNKU PRACY
PublicationPolska, podobnie jak i inne kraje europejskie doświadcza w przyspieszonym tempie zmian demograficznych, które w krajach o rozwiniętych gospodarkach rynkowych rozpoczęły się w latach 60. XX wieku. Procesy nieodwracalne, związane ze starzeniem się społeczeństwa na początku zaobserwowano w Skandynawii, następnie proces ten objął kraje Europy Zachodniej, Europy Południowej, w latach 90. XX wieku – również Europę Środkową i Wschodnią....
-
Wykorzystanie metody Neldera-Meada do identyfikacji wartości parametrów niequasi-statycznego modelu małosygnałowego tranzystora MOS
PublicationW artykule zaprezentowano wyniki zastosowania metody sympleksu Neldera-Meada do ekstrakcji wartości parametrów niequasi-stycznego modelu małosygnałowego tranzystora MOS. Przedstawiono równoważny elektryczny schemat zastępczy i model matematyczny nowego modelu małosygnałowego MOSFETa dla częstotliwości mikrofalowych. Opisano zaimplementowany algorytm i otrzymane rezultaty badań.
-
Behaviour of deformed steel columns exposed to impact load during earthquakes: numerical analysis
PublicationIt has been observed during earthquakes that the so called soft-storey failure of an upper floor of a building leads to considerable vertical impact load acting on structural members of the lower storeys. The aim of this paper is to investigate numerically the behaviour of horizontally deformed columns (deformation as the result of earthquake loading) that are additionally subjected to vertical impact load. In the first stage of...
-
Novel analysis methods of dynamic properties for vehicle pantographs
PublicationTransmission of electrical energy from a catenary system to traction units must be safe and reliable especially for high speed trains. Modern pantographs have to meet these requirements. Pantographs are subjected to several forces acting on their structural elements. These forces come from pantograph drive, inertia forces, aerodynamic effects, vibration of traction units etc. Modern approach to static and dynamic analysis should...
-
FEM modelling of screw displacement pile interaction with subsoil
PublicationPredicting the-settlement characteristics of piles is an important element in the designing of pile foundations. The most reliable method in evaluating pile-soil interaction is the static load test, preferably performed with instrumentation for measuring shaft and pile base resistances. This, however, is a mostly post-implementation test. In the design phase, prediction methods are needed, in which numerical simulations play an...
-
The 12 principles of green analytical chemistry and the SIGNIFICANCE mnemonic of green analytical practices
PublicationThe current rapid development of green analytical chemistry (GAC) requires clear, concise guidelines in the form of GAC principles that will be helpful in greening laboratory practices. The existing principles of green chemistry and green engineering need revision for their use in GAC because they do not fully meet the needs of analytical chemistry. In this article we propose a set of 12 principles consisting of known concepts...
-
Metal-Organic Frameworks in Green Analytical Chemistry
PublicationTaking into consideration the rapid expansion of MOFs applications in the analytical chemistry area, it is important to evaluate the existing and future analytical MOF-based methods according to GAC principles. From this point of view, eco-friendly MOFs-based methods should include features such as: green design and synthesis of MOF, evaluation of toxicity issues of MOFs, and incorporation of MOFs in GAC methods. This Chapter will...
-
Using Wearable Electronics to Estimate Usefulness of Heart Rate Variability for Bathing Person Identif Cation
PublicationIn this paper the possibility of person identification based on biosignal is investigated. The work focus on the analysis of the changes in intervals between successive R-waves of electrocardiogram (ECG) recorded by wearable electronics in form of a necklaces. The main idea behind this project is to find efficient tool which may prevent sudden consciousness loss episodes or even sudden death episodes related to rapid temperature...
-
Economic benefits of dynamic charging of electric buses
PublicationDiesel engines buses are still the most used type of buses. Electric buses provide promising green alternatives and a lot of advantages, but their main disadvantages are limited travel range and long charging time. This article is a presentation of innovative solution for charging of electric busses - Dynamic Charging (IMC). The modern IMC system in Solingen was presented. At the end of the article, a proposal was made to introduce...
-
Głowice optoelektroniczne bezzałogowych środków latających
PublicationBezzałogowe środki latające nie wymagają długiego i kosztownego szkolenia załóg. Koszty ich wdrożenia są wielokrotnie niższe od załogowych środków latających. Bezzałogowe środki latające są następcami załogowych pojazdów latających rozpoznawczych i obserwacyjnych. Jednym z podstawowych elementów wyposażania bezzałogowego środka latającego jest głowica optoelektroniczna. Głowice wyposażone są w systemy rejestracji i śledzenia wskazanych...
-
A novel method for archiving multibeam sonar data with emphasis on efficient record size reduction and storage
PublicationOver the past few years considerable advances in sonar technology, spatial positioning capabilities and computer processing power have lead to significant improvements in mapping, imaging and technologies of seafloor exploration. Recently, modern multibeam echosounder systems (MBES) capable of recording backscatter data for the whole water column, not just for the seabed, have become available thus providing data allowing for...
-
Specification-Oriented Automatic Design of Topologically Agnostic Antenna Structure
PublicationDesign of antennas for modern applications is a challenging task that combines cognition-driven development of topology intertwined with tuning of its parameters using rigorous numerical optimization. However, the process can be streamlined by neglecting the engineering insight in favor of automatic de-termination of structure geometry. In this work, a specification-oriented design of topologically agnostic antenna is considered....
-
Identification of ship’s hull mathematical model with numerical methods
PublicationThe modern maritime industry is moving toward the development of technology that will allow for full or partial autonomy of ship operation. This innovation places high demands on ship performance prediction techniques at the design stage. The researchwork presented in the article is related to the design stage of the ship and concerns methods for prognosis and evaluation of the specific operational condition of the ship, namely...
-
Towards truly sustainable IoT systems: the SUPERIOT project
PublicationThis paper provides an overview of the SUPERIOT project, an EU SNS JU (Smart Networks and Services Joint Undertaking) initiative focused on developing truly sustainable IoT systems. The SUPERIOT concept is based on a unique holistic approach to sustainability, proactively developing sustainable solutions considering the design, implementation, usage and disposal/reuse stages. The concept exploits radio and optical technologies...
-
Investigation of the impact of ITRF2014/IGS14 on the positions of the reference stations in Europe
PublicationIn January 2017, the new realization of the International Terrestrial Reference Frame (ITRF) – ITRF2014, was released. Besides the higher accuracy and consistency of the new frame, an entirely new element – the post seismic deformation - was included. Moreover, the definition of the fundamental points has also been changed. All changes related to the new reference frame haveconsequences in the precise positioning using GNSS observations....
-
Direct design of Controlled Modulus Columns (CMC) based on in-situ testing
PublicationIn this paper, the serviceability limit state and bearing capacity of tension screw displacement piles were analyzed using the results of static pile load tests, carried out on the test plot near the Elbląg city, and field, and laboratory tests. The paper presents the methodology of determining the pile load-settlement curve using different types of t-z transfer functions. The new method of constructing the pile load-settlement...
-
Zastosowanie elektronicznych zmysłów w analizie żywności. Zastosowanie elektronicznego języka w analizie żywności.
PublicationW dzisiejszych czasach konsumenci zwracają dużą uwagę na takie cechy żywności jak: zapach, smak i wygląd. Ze względu na to naukowcy od wielu lat podejmują próby naśladowania ludzkich narządów zmysłów za pomocą urządzeń określanych jako elektroniczne zmysły. Zaliczamy do nich elektroniczny nos i język oraz komputerowy system rozróżnienia barw i kształtów. Elektroniczny język znany również jako sztuczny język lub czujnik smaku,...
-
Comparison of Selection Schemes in Evolutionary Method of Path Planning
PublicationThis article compares an impact of using various selection schemes on the quality of the solution for the problem of planning the path for a moving object using the evolutionary method. In study case problem of avoiding collisions at sea is analyzed. The modelled environment includes static constraints (lands, canals, etc.) and dynamic objects (moving ships). Article analyses behaviour of selection schemes in two similar environments...
-
Hybrid piezoelectric motor based on electroactive lubrication principle
PublicationA novel conception of hybrid piezoelectric motor is presented in this paper. Proposed conception required synchronised work of quasi-static and resonant piezoelectric actuators that results in a rotary movement. The motor's working principle is explained and the main characteristics are described. Studied topology is compared to the existing piezoelectric motors with regards to its field of applications. The assembling process...