Search
Filters
total: 865
Search results for: ISO
-
Images of LEGO bricks
Open Research DataThe set contains images of LEGO bricks (from multiple categories). The images were prepared for training neural network for recognition and labeling of LEGO bricks. The images contain one brick each. The images were taken from different sides by handheld camera hovering over the bricks lying on a white, non reflective surface.
-
ASSESSING THE POTENTIAL REPLACEMENT OF MINERAL OIL WITH ENVIRONMENTALLY ACCEPTABLE LUBRICANTS IN A STERN TUBE BEARING: AN EXPERIMENTAL ANALYSIS OF BEARING PERFORMANCE
PublicationT his study compares the performance of a plain bearing, with a similar structure to a tail shaft stern bearing, lubricated with either mineral oil or an environmentally acceptable lubricant (EAL). The main characteristic of the bearing is its length/diameter ratio of <1. Measurements are carried out with the bearing operating under loads from 0.5 to 1 MPa and seven speeds ranging from 1 to 11 rev/s. The bearing lubricated...
-
Tyre/road noise reduction of poroelastic road surface tested in a laboratory
PublicationA so-called poroelastic road surface (PERS) is being developed in Europe. This contains a large percentage of rubber particles mixed with hard aggregate (stone and sand) and bound with polyurethane. This gives high air void content (around 30 %), high elasticity and smooth texture, all of which should give low noise properties. Inthis experiment anominally 30 mm thick sample of PERS was mounted on a steel drum. Various car tyres...
-
Degradation of xylose using a microbial fuel cell
PublicationIt is generally known, that many kind of microorganisms are capable of using carbohydrates as a source of carbon and energy in an environment. The biodegradation process of monosaccharides from pentoses (in this case- racemic mixture of D - and L – xylose) is an immense opportunity for an entire reduction of biological contamination to neutral compounds through MFC. The process is occurred in a single-chamber MFC, which is contained...
-
Analiza bezpieczeństwa funkcjonalnego i ochrony informacji w rozproszonych systemach komputerowych pełniących funkcje sterowania i zabezpieczeń
PublicationW niniejszym artykule przedstawiona została problematyka związana z analizą bezpieczeństwa funkcjonalnego rozproszonych systemów sterowania i automatyki zabezpieczeniowej z uwzględnieniem zagadnień ochrony informacji. Powinny być one rozpatrywane w sposób zintegrowany w zależności od rodzaju komunikacji stosowanej do transmisji danych. W tym celu zaproponowano podział analizowanych systemów na trzy kategorie. Zaproponowane podejście...
-
Analiza bezpieczeństwa funkcjonalnego i ochrony informacji w rozproszonych systemach komputerowych pełniących funkcje sterowania i zabezpieczeń
PublicationW niniejszym artykule przedstawiona została problematyka związana z analizą bezpieczeństwa funkcjonalnego rozproszonych systemów sterowania i automatyki zabezpieczeniowej z uwzględnieniem zagadnień ochrony informacji. Powinny być one rozpatrywane w sposób zintegrowany w zależności od rodzaju komunikacji stosowanej do transmisji danych. W tym celu zaproponowano podział analizowanych systemów na trzy kategorie. Zaproponowane podejście...
-
The impedance of hydrogen oxidation reaction in a proton exchange membrane fuel cell in the presence of carbon monoxide in hydrogen stream
PublicationEvaluation of performance of a proton exchange membrane fuel cell, which is affected by carbon monoxide that pollutes the hydrogen stream, was presented. This influence was studied for carbon monoxide concentration of 125–325 ppb, which are close to values specified in ISO 14687:2019 standard. Performed studies provided crucial information for further development of fuel cell as an energy source for automotive application. Impedance...
-
Accurate rolling resistance Rolling resistance measurements can be influenced by a number of factors
PublicationTire rolling resistance is one of the most difficult-to-measure parameters of the tire/ pavement interface, especially if road measurements are required. First of all, it is necessary to measure a fairly small force in the system that is heavily loaded by other forces and subjected to many adverse effects causing measurement errors. The second problem is related to the fact that tire rolling resistance depends on many factors,...
-
Double-diffusive natural convection energy transfer in magnetically influenced Casson fluid flow in trapezoidal enclosure with fillets
PublicationThe prime motive of this disquisition is to deal with mathematical analysis of natural convection energy transport driven by combined buoyancy effects of thermal and solutal diffusion in a trapezoidal enclosure. Casson fluid rheological constitutive model depicting attributes of viscoelastic liquids is envisioned. The influence of the inclined magnetic field governed by Lorentz field law is also considered. To raise the essence...
-
An in-depth look at the tire rubber hardness influence on tire/road noise measurements
PublicationWhen assessing the acoustic quality of a road pavement with the close-proximity (CPX) or the on-board sound intensity (OBSI) method, the rubber hardness of the reference tire substantially affects the measurement. Practical experience shows that measurement tires can get significantly harder within a single measurement season. This is why one would like to normalize measurements to a reference rubber hardness. The recently published...
-
Polymerization of chloro-p-xylylenes, quantum-chemical study
PublicationThe p-xylylene monomers of parylene N, C and D have similar high polymerization reactivity. For effective copolymerization processes this fact is basically a draw- back and for instance the copolymerization with styrene doesn't go at all (Corley et al. J Pol Sc 13(68):137156, 1954). Substitution of terminal hydrogen atoms by chlorine atoms reduces reactivity dramatically. 7,7,8,8-tetrachloro-p- xylylene and 2,5,7,7,8,8-hexachloro-p-xylylene...
-
Advantages of the Application of the Temper Bead Welding Technique During Wet Welding
PublicationThermo-mechanically rolled S460ML steel was chosen for welding in underwater wet welding conditions by covered electrodes. The main aim of this study was to check the weldability for fillet welds in a water environment by controlled thermal severity (CTS) tests and to check the influence of temper bead welding (TBW) on the weldability of the investigated steel. Non-destructive and destructive tests showed that S460ML steel has...
-
Specyfika kontenerowego systemu transportu,sem_5, Systemy Transportu Wodnego,W,S, zima24/25, PG_00056228
e-Learning CoursesWykłady dotyczą: cechy kontenerowego systemu transportu: opakowanie ładunków, oznakowanie ładunków, ocechowanie ładunków - ładunki zjednostkowane. Charakterystyka poszczególnych grup ładunkowych jako przedmiotów procesu produkcyjnego portu kontenerowego.Definicja kontenera. Ogólna klasyfikacja kontenerów. Parametry kontenerów serii I ISO. Kontenery "lądowe/morskie". Rodzaje uszkodzeń wywołanych możliwymi przemieszczeniami ładunków...
-
Microstructural evolution and mechanical behavior of activated tungsten inert gas welded joint between P91 steel and Incoloy 800HT
PublicationThis study examines the welded joint between P91 steel and Incoloy 800HT using the Activated Tungsten Inert Gas (A-TIG) welding process. The focus is on analyzing the microstructure and evaluating the mechanical properties of joints made with different compositions of activating flux. Owing to the reversal of the Marangoni effect in which the conventional direction of molten metal flow in the weld pool is reversed due to the application...
-
RAPORT - EKSPERTYZA Z POMIARÓW DRGAŃ LINII WAŁÓW NA JEDNOSTCE R14
PublicationEkspertyza diagnostyczna dotycząca stanu technicznego lini transmisji mocy (linii wałów) opracowana na podstawie przeprowadzonych pomiarów drgań. Pomiary prędkości i przyspieszeń drgań generowanych przez węzły konstrukcyjne linii wałów okrętowego układu napędowego wykonano po naprawie głównej napędu okrętu w stoczni „NAUTA”, w celu określenia jego stanu dynamicznego. Rejestrację drgań przeprowadzono w płaszczyźnie pionowej (V)...
-
Generatory zmian służące doskonaleniu usług medycznych
PublicationW rozdziale zaprezentowano podstawowe aspekty usług medycznych. Opisano typowe cechy usług, które odniesiono do usług medycznych, a także wyznaczono specyficzne cechy dla tego rodzaju usług. Następnie podjęto próbę zdefiniowania pojęcia jakość w usługach medycznych w nawiązaniu do potrzeb pacjenta. W rozdziale przybliżono najważniejsze z obecnie stosowanych, mechanizmów zapewnienia jakości w usługach medycznych, którymi są: Certyfikacja...
-
Temperature influence on tyre/road noise frequency spectra
PublicationThe correction for temperature effect on measured tyre/road noise is very important as it may be one of the main sources of errors in measurement results due to substantial influence of this parameter on obtained values. The latest version of the Technical Specification ISO/CD TS 13471-1 about Temperature Corrections contains a proposal of correction procedure for normalizing measured noise levels to a reference air temperature...
-
Fracture surface topography measurements analysis of low-alloyed corrosion resistant steel after bending-torsion fatigue tests
PublicationIn this paper, an assessment of a topography measurement method for fracture surfaces of 10HNAP steel after bending-torsion fatigue tests was performed. Surface roughness was measured by using a non-contact Focus Variation Microscopy (FVM) technique in which the non-measured points (NMPs) and outliers (spikes) were removed by the application of general methods. The results revealed, that the optical measurement method introduced...
-
Studies of the separation performance of silanized silica gel for simulated distillation
PublicationWe present the results of investigations of the chromatographic (sorptive) properties of silanized silica gel as a stationary phase for gas chromatography used for simulated distillation. Commercially available silanized sorbent (particle diameter range 63–200 m, average pore size 60 Å) was sieved to obtain the 80–100 mesh fraction (180–150 m). The obtained results revealed that silanized silica gel allows the complete separation...
-
EH36 steel for shipbuilding (plate thicnkness 50 mm) - CMOD - force record, a0/W = 0.5
Open Research DataThe basic method of ductility designation of structural steels is the Charpy impact test. The test consists of a single strike of the specimen using a Charpy pendulum. Its result is the value of work necessary to break a specimen at a test temperature. Despite its many advantages, such as its short implementation time and low costs, it has its disadvantages,...
-
EH36 steel for shipbuilding (plate thicnkness 50mm) - CMOD - force record, a0/W = 0.6
Open Research DataThe basic method of ductility designation of structural steels is the Charpy impact test. The test consists of a single strike of the specimen using a Charpy pendulum. Its result is the value of work necessary to break a specimen at a test temperature. Despite its many advantages, such as its short implementation time and low costs, it has its disadvantages,...
-
RAPORT-EKSPERTYZA Z POMIARÓW DRGAŃ LINII WAŁÓW NA JEDNOSTCE ORP „PIORUN”
PublicationEkspertyza diagnostyczna dotycząca stanu technicznego lini transmisji mocy (linii wałów) opracowana na podstawie przeprowadzonych pomiarów drgań. Pomiary prędkości i przyspieszeń drgań generowanych przez węzły konstrukcyjne linii wałów okrętowego układu napędowego wykonano po naprawie głównej napędu okrętu w stoczni „NAUTA”, w celu określenia jego stanu dynamicznego. Rejestrację drgań przeprowadzono w: • płaszczyźnie pionowej (V)...
-
Numerical analysis of vacuum drying of a porous body in the integrated domain
Publicationn the present study, the vacuum drying process of an apple slice is numerically modeled based on a control volume method. Transient two-dimensional Navier– Stokes, energy, moisture, and Luikov equations are solved by numerical coding (Fortran) to simulate the simultaneous heat and mass transfer in the ambient and apple slice, respectively. The privilege of using Luikov's model is that the capillary forces are considered, and a...
-
Modele strumienia powietrza w pneumatyce
PublicationPraca porusza problematykę modelowania strumienia masy i strumienia objętości w zadaniach analizy i syntezy w pneumatyce. W szczególności skoncentrowano się na możliwości wykorzystania w tych zagadnieniach modelu strumienia masy powietrza opisanego w normie ISO 6953. Jest to model zdefiniowany w dziedzinie ciśnień statycznych i wykorzystujący do określenia oporności elementu pneumatycznego cztery parametry (współczynniki przepływu):...
-
Autogenous Fiber Laser Welding of 316L Austenitic and 2304 Lean Duplex Stainless Steels
PublicationThis study presents results of experimental tests on quality of dissimilar welded joints between 316L austenitic and 2304 lean duplex stainless steels, welded without ceramic backing. Fiber laser welded butt joints at a thickness of 8 mm were subjected to non‐destructive testing (visual and penetrant), destructive testing (static tensile test, bending test, and microhardness measurements) and structure observations (macro‐ and...
-
Reduction in Errors in Roughness Evaluation with an Accurate Definition of the S-L Surface
PublicationCharacterization of surface topography, roughly divided into measurement and data analysis, can be valuable in the process of validation of the tribological performance of machined parts. Surface topography, especially the roughness, can respond straightly to the machining process and, in some cases, is defined as a fingerprint of the manufacturing. When considering the high precision of surface topography studies, the definition...
-
Corrosivity of environment and the current state of the steel elements at the former Auschwitz concentration camp
PublicationThe objective of this study was to assess corrosivity of the atmospheric environment in the former Auschwitz I and Auschwitz II-Birkenau concentration and extermination camp, and to identify the protective properties of existing corrosion products in order to estimate the actual corrosion rate of original steel elements located there. The current atmospheric corrosivity of the former Auschwitz camp, specified during one year of exposure...
-
INFLUENCE OF MEASURING CONDITIONS ON TYRE/ROAD NOISE
PublicationA decisive factor for the development of tyres and road surfaces is the ability to conduct representative and reproducible measurements of selected characteristics related to the interaction of tyres and road surfaces. In terms of tyre/road noise measurements in Europe two methods described in ISO/FDIS 11819-2 and ECE Regulation No.117 are used. The latter is compulsory for assigning the tyre noise labels. The methodologies differ...
-
Sebastian Wilczewski dr inż.
PeoplePhD. Sebastian Wilczewski is employed as an Assistant Professor in the Department of Applied Informatics in Management, Faculty of Management and Economics. Additionally, he has been working in IT companies for over 20 years, where he held positions from an system engineer and consultant, through the position of Project Manager, Portfolio Manager and Process Owner to the position of Team Leader for a team of about 30 IT analysts. Areas...
-
PLA–Potato Thermoplastic Starch Filament as a Sustainable Alternative to the Conventional PLA Filament: Processing, Characterization, and FFF 3D Printing
PublicationThe growing popularity of the fused filament fabrication (FFF) 3D printing technology in science, industry, and in-home use is associated with an increased demand for high-quality polymer filaments. This study presents an in-depth characterization and analysis of a self-made bio-based polylactide (PLA)/thermoplastic potato starch (TPS) filament dedicated for the FFF 3D printing technology. The obtained results were compared with...
-
Thermal-Resistant Polyurethane/Nanoclay Powder Coatings: Degradation Kinetics Study
PublicationIn the present study, thermal degradation kinetics of polyurethane (PU) powder coatings reinforced with organo-modified montmorillonite (OMMT) was investigated. PU nanocomposites were prepared in different concentrations of 1, 3, and 5 wt.% of OMMT via the extrusion method. The microstructure of the nanocomposites was observed by scanning electron microscope (SEM) illustrating uniform dispersion of OMMT nano-clay platelets in the...
-
Klaudia Skelnik dr
Peopledr Klaudia Skelnik Prodziekan Wydziału Prawa i Administracji Wyższa Szkoła Bankowa w Gdańsku, doktor nauk społecznych w dyscyplinie nauki o bezpieczeństwie, absolwent studiów MBA zarządzanie bezpieczeństwem, mgr politologii w specjalizacji ustrojowo-samorządowej, posiadająca podyplomowe wykształcenie wyższe w zakresie prawa Unii Europejskiej, Edukacji dla bezpieczeństwa, Bezpieczeństwa i Higiena Pracy oraz szereg kursów i szkoleń...
-
Processing of Polyester-Urethane Filament and Characterization of FFF 3D Printed Elastic Porous Structures with Potential in Cancellous Bone Tissue Engineering
PublicationThis paper addresses the potential of self-made polyester-urethane filament as a candidate for Fused Filament Fabrication (FFF)-based 3D printing (3DP) in medical applications. Since the industry does not provide many ready-made solutions of medical-grade polyurethane filaments, we undertook research aimed at presenting the process of thermoplastic polyurethane (TPU) filament formation, detailed characteristics, and 3DP of specially...
-
Comparison of Tire Rolling Resistance Measuring Methods for Different Surfaces
PublicationThe rolling resistance of car tires is one of the most important parameters characterizing tires today. This resistance has a very significant contribution to the energy consumption of wheeled vehicles. The climate crisis has forced tire and car manufacturers to place great emphasis on the environmental impact of their products. Paradoxically, the development of electric vehicles has led to an even greater importance of rolling...
-
Results of accelerometer measurements in rail passenger transport vehicles
Open Research DataAs part of the project, field research was done to better understand how unbalanced accelerations affect passenger comfort in rail transport and to compare this with passengers’ actual, subjective feelings. Data were collected from different types of rail vehicles, like trains and trams, using common mobile devices with MEMS accelerometer sensors.
-
A comprehensive evaluation of flexible FDM/FFF 3D printing filament as a potential material in medical application
PublicationThe use of FDM/FFF in 3D printing for medical sciences is becoming common. This is due to the high availability and decent price of both 3D printers and filaments useful for FDM/FFF. Currently, researchers' attention is focused mainly on the study of medical filaments based on PLA, PCL or their modifications. This contributes to insufficient diversity of medical-grade filaments on the market. Moreover, due to the lack of specified...
-
Usability of mobile applications: a systematic literature study
PublicationSince the release of the first mobile devices, the usability of on-board applications has been the concern not only of software vendors but hardware manufacturers as well. The academia community later willingly joined the discussion on usability in terms of theory and empirical measurement, having experience and knowledge in desktop settings. At first sight, such a background should guarantee a solid foundation to conduct research...
-
Opracowanie deskryptora nawierzchni drogowej do oceny oporu toczenia opon samochodowych
PublicationNa początku niniejszej pracy pt. „Opracowanie deskryptora nawierzchni drogowej do oceny oporu toczenia opon samochodowych” przedstawiono zagadnienia dotyczące oporów ruchu pojazdu. Omówiono metody zarówno drogowe, jak i laboratoryjne badań oporu toczenia opon samochodowych. Zaprezentowano przykładowe wartości współczynników oporu toczenia opon na różnych rodzajach nawierzchni. Kolejno omówiono metody pomiaru tekstury nawierzchni....
-
Influence of PWHT Parameters on the Mechanical Properties and Microstructural Behavior of Multi-Pass GTAW Joints of P92 Steel
PublicationThe 9% Cr steels were developed for ultra-supercritical (USC) power plants to meet the requirements of high operating temperature and pressure. These steels are produced to operate at high temperatures where impact toughness is not a concern; however, it becomes important for the welded joints to have good impact toughness at room temperature for manufacturing. The present work investigates the effect of the post-weld heat treatment...
-
Discussion of Derivability of Local Residual Stress Level from Magnetic Stray Field Measurement
PublicationThe NDT procedure dubbed ‘metal magnetic memory’ method and the related ISO 24497 standard has found wide industrial acceptance in some countries, mainly in Russia and China. The method has been claimed by some researchers (Roskosz and Bieniek in NDT&E Int 45:55–62, 2012; Wilson et al. in Sens Actuators A 135:381–387, 2007) as having potential for quantitative determination of local residual stress state in engineering structures,...
-
Ochrona środowiska w przemyśle [Moduł dyscyplinarny, Grupa B]
e-Learning CoursesProwadzący: Dr hab. inż. Grzegorz Boczkaj prof. PG Terminy realizacji: 22.10 (sob), od 9:15 do 11:45 29.10 (sob), od 9:15 do 11:45 6.11(ndz), od 9:15 do 11:45 12.11 (sob), od 9:15 do 11:45 10.12 (sob), od 11:15 do 13:45 Tematyka realizowanego przedmiotu obejmuje zagadnienia oddziaływań zewnętrznych na środowisko i źródeł zanieczyszczeń w przemyśle oraz: Technologie oczyszczania gazów odlotowych Technologie oczyszczania...
-
Kontrola jakości połaczeń, PG_00055250
e-Learning CoursesZadania i cele kontroli złączy spawanych w procesie wytwarzania konstrukcji spawanej i w remontach. Kontrola wstępna, bieżąca i ostateczna. Ekonomiczne aspekty kontroli Badania nieniszczące. Badania niszczące. Badania wizualne (VT). Wymagania normalizacyjne. Aparatura i środki do badan: boroskopy, fiberoskopy, zestawy wideoskopowe. Badania Penetracyjne (PT). Systemy odczynników i próbki odniesienia do badań. Normy dotyczące badań...
-
Wybrane problemy szlifowania powierzchni płaskich z kinematyką docierania
PublicationW pracy przedstawiono teoretyczne i doświadczalne podstawy szlifowania powierzchni płaskich z kinematyką docierania. Dokonano kompleksowej analizy zastosowanych układów kinematycznych szlifierek. Przeprowadzono eksperymenty szlifowania jednostronnego ściernicami o spoiwie galwanicznym z ziarnami diamentowymi (D107, D64 i D46) oraz z regularnego azotku boru (B107 i B64). Innowacyjność ściernic polegała na zróżnicowanym utwierdzeniu...
-
Underwater Local Cavity Welding of S460N Steel
PublicationIn this paper, a comparison of the mechanical properties of high-strength low-alloy S460Nsteel welded joints is presented. The welded joints were made by the gas metal arc welding (GMAW)process in the air environment and water, by the local cavity welding method. Welded joints were testedfollowing the EN ISO 15614-1:2017 standard. After welding, the non-destructive—visual, penetrant,radiographic, and ultrasonic (phased array) tests...
-
Perspektywa jakości w szkolnictwie wyższym. O modelu QualHE
PublicationOddawana do rąk Czytelników monografia wnosi wkład w wypełnianie wspomnianej luki, przede wszystkim poprzez: • przedstawienie szerokiego kontekstu ogólnoświatowego dyskursu dotyczącego kategorii jakości w szkolnictwie wyższym w ujęciu teoriopoznawczym i w wynikach badań empirycznych; • określenie potencjału i uwarunkowań aplikacyjnych dotyczących takich koncepcji jak TQM Lean Management, Six Sigma czy Lean Six Sigma; • przedstawienie...
-
Lean Quality Management
PublicationPostrzeganie przedsiębiorstwa przez pryzmat zachodzących w nim procesów powoduje powstanie dynamicznego obrazu zmian zachodzących w firmie. W wyniku takiego spojrzenia obserwator wykracza poza funkcjonalny układ struktur uzyskując możliwość pełniejszej weryfikacji skuteczności licznych, powiązanych ze sobą działań przedsiębiorstwa i podejmowania decyzji o ich doskonaleniu. Kierunki tego doskonalenia to takie budowanie sekwencji...
-
Usability of Mobile Applications: A Consolidated Model
PublicationMobile devices have become an integral part of the digital ecosystem, connecting people, businesses, and information around the world in ways never before possible. In particular, smartphones, tablets and other handheld devices equipped with mobile applications have changed every aspect of our lives. Today, a user can choose from nearly five million applications available for both Android and iOS operating systems. However, only...
-
Analysis of the influence of polystyrene microplastics and their derivatives on the DNA of human colon epithelial cells HT29 with the comet assay
PublicationWe have been using plastic for almost a century and nowadays a lot of them circulates as pollutants in the environment and still defragmenting to micro and nanoscale. The exposition through the food chain and its precise impact on human health is still not clear. In our study, we tested real food packaging after contact with food products and real thermoinsulation and environmental samples of polystyrene in different model liquids,...
-
Process Control in Food Fermentation
Publication -
Perspektywa jakości w szkolnictwie wyższym. O modelu QualHE
PublicationKategoria jakości w szkolnictwie wyższym, choć tak ważna dla zapewnienia oczekiwanego tempa rozwoju państw i społeczeństw, ciągle jeszcze nie znajduje odpowiadającego jej randze odzwierciedlenia w pracach przedstawiających tę problematykę w sposób holistyczny, w odniesieniu do stale zmieniających się możliwości i wyzwań. Oddawana do rąk Czytelników monografia wnosi wkład w wypełnianie wspomnianej luki, przede wszystkim poprzez:...