Search
Filters
total: 2397
-
Catalog
displaying 1000 best results Help
Search results for: DISTRIBUTION OF RELAXATION TIMES
-
Optimal configuration of an electrode array for measuring ventricles' contraction
PublicationAn influence of an electrode-array configuration on an impedance signal composition for a fixed spatial distribution of its sources is examined in the paper. The Finite Element Method and Geselowitz relationship were used for examining three different electrode-arrays. A sensitivity approach was used to evaluate each configuration assuming that localization of the signal source is known. A conductivity change, thus the source of...
-
A method of nonlinearities of transformer no-load characteristic modelling
PublicationA way in which changes of the no-load characteristic are taken into account in the mathematical model of the transformer is presented. Changes of saturation within core of transformer are presented as a combined non-linear flux curve. Analysis of magnetization of the transformer core and simulation of no-load state for distribution transformer of 30 kVA power rating and 15.75/0.4 kV/kV (especially supplying VLV) transformation...
-
Estimation of the uncertainty of the AC/AC transducer output voltage
PublicationThe paper presents a methodology for estimating uncertainty of voltage transducers processing function, on the example of CYVS411D07 voltage transducers. The analysis was conducted using the method based on the GUM Guide propagation of uncertainty law and the determination of the coverage factor based on the effective number of degrees of freedom (t-Student distribution). The paper also presents example evaluation results of measured...
-
Metrological analysis of precision of the system of delivering a water capsule for explosive production of water aerosol
PublicationIn this paper an analysis of precision of the system controlling delivery by a helicopter of water-capsule designed for extinguishing large scale fires is presented. The analysis was performed using the numerical method of distribution propagation (Monte Carlo method) supplemented with results of application of the uncertainty propagation method. In addition the optimum conditions for the airdrop are determined to ensure achievement...
-
Measurements of Two-phase Flows in Pipelines Using Radioisotopes and Statistical Signal Processing
PublicationThis paper presents an application of radiotracers and gamma absorption method in two-phase flow measurements in pipelines. Two different methods were implemented to analysis of acquired signals. Investigated methods are based on the cross-correlation function and the phase of the cross-spectral density distribution. The examples presented in the article illustrate the application of the radioisotopes to evaluation of liquid-gas...
-
Kształtowanie toru zwrotnego rozjazdu z odcinkami krzywizny liniowej
PublicationW pracy została przedstawiona analityczna metoda kształtowania toru zwrotnego rozjazdu kolejowego posiadającego na swojej długości odcinki krzywizny liniowej. Odróżnia go to w istotny sposób od rozwiązania typowego, stanowiącego pojedynczy łuk kołowy bez krzywych przejściowych. W metodzie tej dokonano identyfikacji problemu rozkładu krzywizny za pomocą równań różniczkowych. Uzyskane rozwiązania mają charakter uniwersalny; m. in....
-
Numeryczna symulacja pracy gazowego kotła wodnego oraz ocena jego wpływu na środowisko
PublicationIlość dostarczanego powietrza oraz rozkład jego koncentracji w komorze paleniskowej mają istotny wpływ na prawidłowość przebiegu procesu spalania. Uzyskanie jednorodnego rozkładu jest praktycznie niemożliwe, dlatego powietrze dostarczane jest w nadmiarze. Konieczne jest jednak dobranie takiej wartości współczynnika nadmiaru powietrza, która pozwoli ograniczyć stratę wylotową, utrzymując przy tym wartości emisji na możliwie niskim...
-
"Numeryczna symulacja pracy gazowego kotła wodnego raz ocena jego wpływu na środowisko"
PublicationIlość dostarczanego powietrza oraz rozkład jego koncentracji w komorze paleniskowej mają istotny wpływ na prawidłowość przebiegu procesu spalania. Uzyskanie jednorodnego rozkładu jest praktycznie niemożliwe, dlatego powietrze dostarczane jest w nadmiarze. Konieczne jest jednak dobranie takiej wartości współczynnika nadmiaru powietrza, która pozwoli ograniczyć stratę wylotową, utrzymując przy tym wartości emisji na możliwie niskim...
-
"Numeryczna symulacja pracy gazowego kotła wodnego oraz ocena jego wpływu na środowisko"
PublicationIlość dostarczanego powietrza oraz rozkład jego koncentracji w komorze paleniskowej mają istotny wpływ na prawidłowość przebiegu procesu spalania. Uzyskanie jednorodnego rozkładu jest praktycznie niemożliwe, dlatego powietrze dostarczane jest w nadmiarze. Konieczne jest jednak dobranie takiej wartości współczynnika nadmiaru powietrza, która pozwoli ograniczyć stratę wylotową, utrzymując przy tym wartości emisji na możliwie niskim...
-
Shared processor scheduling
PublicationWe study the shared processor scheduling problem with a single shared processor to maximize total weighted overlap, where an overlap for a job is the amount of time it is processed on its private and shared processor in parallel. A polynomial-time optimization algorithm has been given for the problem with equal weights in the literature. This paper extends that result by showing an (log)-time optimization algorithm for a class...
-
Miniaturized impedance analyzer using AD5933
PublicationThe paper presents the analyzer allowing to measure impedance in a range of 10 ohms <|Zx|<10 Gohms in a wide frequency range from 10 mHz up to 100 kHz. The device specific features are: miniaturization, low power consumptions and the use of impedance measurement method based on DSP. These features were possible thanks to the use of newest generation of large scale integration chips: e.g. „system on a chip” microsystems (AD5933)...
-
A FPTAS for minimizing total completion time in a single machine time-dependent scheduling problem
PublicationIn this paper a single machine time-dependent scheduling problem with total completion time criterion is considered. There are given n jobs J1,…,Jn and the processing time pi of the ith job is given by pi=a+bisi, where si is the starting time of the ith job (i=1,…,n),bi is its deterioration rate and a is the common base processing time. If all jobs have deterioration rates different and not smaller than a certain constant u>0,...
-
Reject water and landfil leachate treatment with hydrophyte method - preliminary results
PublicationTreatment of landfill leachate (LL) and reject water (RWC) from dewatering of digested sludge in WWTPs have become one of the actual problems. Treatment of both types of wastewater is in many cases very costly and difficult due to quality and quantity fluctuations in time as well as high concentrations of specific pollutants. In case of our investigation the TSS concentration in RWC was two times higher than in LL. The shere of...
-
Determination of Local Dye Concentration in Hybrid Porous Silica Thin Films
PublicationThe idea of determination of local dye concentration in a nanoporous matrix is proposed based on donor − acceptor energy transfer. The method was tested for a Rhodamine 110 − Rhodamine 101 system in silica and methylated silica nanolayers. Evaluation of acceptor (Rhodamine 101) local concentration was carried out by comparing the results of Monte Carlo simulation of energy transfer from donor (Rhodamine 110) to acceptor (Rhodamine...
-
Miniaturized impedance analyzer using AD5933
PublicationThe paper presents the analyzer allowing to measure impedance in a range of 10 ohms <|Zx|<10 Gohms in a wide frequency range from 10 mHz up to 100 kHz. The device specific features are: miniaturization, low power consumptions and the use of impedance measurement method based on DSP. These features were possible thanks to the use of newest generation of large scale integration chips: e.g. „system on a chip” microsystems (AD5933)...
-
Possible quadrupole-order-driven commensurate-incommensurate phase transition in B20 CoGe
PublicationThe B20-type cobalt germanide CoGe was investigated by measuring the specific heat, resistivity, and 59Co nuclear magnetic resonance (NMR).We observed a phase transition at TQ = 13.7 K, evidenced by a very narrow peak of the specific heat and sharp changes of the nuclear spin-spin (T −1 2 ) and spin-lattice (T −1 1 ) relaxation rates. The fact that the entropy release is extremely small and the Knight shift is almost independent...
-
Antifungal Activity of Capridine β as a Consequence of Its Biotransformation into Metabolite Affecting Yeast Topoisomerase II Activity
PublicationIn the last few years,increasing importance is attached to problems caused by fungal pathogens. Current methods of preventing fungal infections remain unsatisfactory. There are several antifungal compounds whichare highly effective in some cases, however, they have limitations in usage: Nephrotoxicity and other adverse effects. In addition, the frequent use of available fungistatic drugs promotes drug resistance....
-
Electromagnetic Control and Dynamics of Generalized Burgers’ Nanoliquid Flow Containing Motile Microorganisms with Cattaneo–Christov Relations: Galerkin Finite Element Mechanism
PublicationIn our research work, we have developed a model describing the characteristics of the bio-convection and moving microorganisms in the flows of a magnetized generalized Burgers’ nanoliquid with Fourier’s and Fick’s laws in a stretchable sheet. Considerations have been made to Cattaneo–Christov mass and heat diffusion theory. According to the Cattaneo–Christov relation, the Buongiorno phenomenon for the motion of a nanoliquid in...
-
Dielectric Properties of BiNbO<sub>4</sub>-Based Ceramic-Polymer Composites with 0-3 Connectivity
PublicationIn the present study two-phase BiNbO4//PVDF composites with 0-3 connectivity were studied by impedance spectroscopy within the frequency range Δν=100Hz-1MHz at room temperature. Polyvinylidene fluoride (PVDF) acted as a matrix whereas bismuth niobate (BiNbO4) powder acted as a dispersed phase. The volume fraction of the ceramic phase was cV=2, 4, 6, 8, 10, 16 and 20vol%. Analysis of the impedance data registered for composites...
-
Polaronic and Mott insulating phase of layered magnetic vanadium trihalide VCl3
PublicationTwo-dimensional (2D) van der Waals (vdW) magnetic 3d-transition metal trihalides are a new class of functional materials showing exotic physical properties useful for spintronic and memory storage applications. In this article, we report the synthesis and electromagnetic characterization of single-crystalline vanadium trichloride, VCl 3 , a novel 2D layered vdW Mott insulator, which has a rhombohedral structure (R3, No. 148) at...
-
How Integration of a Brain-Machine Interface and Obstacle Detection System Can Improve Wheelchair Control via Movement Image
PublicationThis study presents a human-computer interaction combined with a brain-machine interface (BMI) and obstacle detection system for remote control of a wheeled robot through movement imagery, providing a potential solution for individuals facing challenges with conventional vehicle operation. The primary focus of this work is the classification of surface EEG signals related to mental activity when envisioning movement and deep relaxation...
-
Integration, Processing and Dissemination of LiDAR Data in a 3D Web-GIS
PublicationThe rapid increase in applications of Light Detection and Ranging (LiDAR) scanners, followed by the development of various methods that are dedicated for survey data processing, visualization, and dissemination constituted the need of new open standards for storage and online distribution of collected three-dimensional data. However, over a decade of research in the area has resulted in a number of incompatible solutions that offer...
-
Explanation of Reduction of Pressure Forces in Turbine Chamber Seals
PublicationThe paper describes a chamber seal reducing the aerodynamic forces created in shroud seals. Asymmetrical pressure distribution (due to rotor-stator eccentricity) in the blade tip clearance leads to the creation of pressure forces acting on the blade shroud. By increasing the volume above the shroud, the pressure distribution becomes more uniform on the whole shroud circumference and the effect of rotor eccentricity is reduced....
-
Propagation of Acoustic Disturbances in Shallow Sea
PublicationPropagation of acoustic waves in shallow sea differs fundamentally from the same phenomenon occurring in deep sea in view of non-negligible distance from the sea bottom in the first case, where presence of two regions limiting the water layer results in the acoustic pressure distribution induced by a harmonic source has an interferential nature as a result of multi-path propagation of the acoustic signal. These interferential properties...
-
Explanation of Reduction of Pressure Forces in Turbine Chamber Seals
PublicationThe paper describes a chamber seal reducing the aerodynamic forces created in shroud seals. Asymmetrical pressure distribution (due to rotor-stator eccentricity) in the blade tip clearance leads to the creation of pressure forces acting on the blade shroud. By increasing the volume above the shroud, the pressure distribution becomes more uniform on the whole shroud circumference and the effect of rotor eccentricity is reduced....
-
Process zone in the Single Cantilever Beam under transverse loading. - Part II: Experimental
PublicationThis paper describes an experimental arrangement to evaluate stress/strain fields in the process zone of asymmetric adhesively bonded joints. A transparent polycarbonate flexible beam was bonded to an aluminium alloy rigid block with an epoxy adhesive in a Single Cantilever Beam (SCB) configuration. The flexible adherend was loaded in the direction parallel to the initial crack front at constant rate. To monitor strains induced...
-
New kinematic systems in single-sided lapping and their influence on lap wear
PublicationPrevious studies on one-sided lapping allow to state that not only parameters of lapping elements (i.e. properties of workpiece, abrasive grains and lapping plate) impact on a lapping efficiency. Influential are also kinematics and dynamics of the process. It is crucial to control an average velocity of lapping (v), a distribution of tangential acceleration (at), a nominal pressure (p), a lapping time (t) and disposal of workpiece...
-
Effect of Flow Normalization in Micro-Pin-Finned Heat Sink: Numerical Study
PublicationThe micro-pin-fin heat sink (MPFHS) is widely employed for the heat transfer enhancement of microchannel heat sinks. In the current paper, the effect of flow normalization on the thermohydraulic performance of micro-pin-finned heat sinks is studied numerically. Two geometries of MPFHSs, the conventional design micro-pin-fin heat sink (CD-MPFHS) with a uniform-width micro pin fin and the proposed design micro-pin-fin heat sink (PD-MPFHS)...
-
Robust Object Detection with Multi-input Multi-output Faster R-CNN
PublicationRecent years have seen impressive progress in visual recognition on many benchmarks, however, generalization to the out-of-distribution setting remains a significant challenge. A state-of-the-art method for robust visual recognition is model ensembling. However, recently it was shown that similarly competitive results could be achieved with a much smaller cost, by using multi-input multi-output architecture (MIMO). In this work,...
-
Robust Object Detection with Multi-input Multi-output Faster R-CNN
PublicationRecent years have seen impressive progress in visual recognition on many benchmarks, however, generalization to the out-of-distribution setting remains a significant challenge. A state-of-the-art method for robust visual recognition is model ensembling. However, recently it was shown that similarly competitive results could be achieved with a much smaller cost, by using multi-input multi-output architecture (MIMO). In this work,...
-
Screw displacement pile shaft deformations measured by vibrating wire and fiber optic systems during a static load test
PublicationThis paper describes a full scale static load test performed on a 400 mm diameter screw displacement pile equipped with four different strain measuring systems. Three types of vibrating wire strain gauges (VWSG) were used: global - retrievable, local attached to steel pipe and local concrete embedded. The fourth system was distributed fiber optic sensors based on Rayleigh back scattering (DFOS) - three in the pile cross section....
-
Heavy Metals in Sediments of Urban Streams: Contamination and Health Risk Assessment of Influencing Factors
PublicationSediments of two urban streams in northern Poland outflowing to the Baltic Sea were assessed to explain the spatial variation in relation to urbanization level of the catchment, the role of retention tanks (RTs) and identification of pollution level. During the 3 month period of investigation sediment samples were collected from the inflow (IN) and outflow (OUT) of six RTs located on streams for flood protection. Six heavy metals...
-
Finite-difference time-domain analyses of active cloaking for electrically-large objects
PublicationInvisibility cloaking devices constitute a unique and potentially disruptive technology, but only if they can work over broad bandwidths for electrically-large objects. So far, the only known scheme that allows for broadband scattering cancellation from an electrically-large object is based on an active implementation where electric and magnetic sources are deployed over a surface surrounding the object, but whose ‘switching on’...
-
UV Light-Modulated Fluctuation-Enhanced Gas Sensing by Layers of Graphene Flakes/TiO2 Nanoparticles
PublicationWe present experimental results of fluctuation-enhanced gas sensing by low-cost resistive sensors made of a mixture of graphene flakes and TiO2 nanoparticles. Both components are photocatalytic and activated by UV light. Two UV LEDs of different wavelengths (362 and 394 nm) were applied to modulate the gas sensing of the layers. Resistance noise was recorded at low frequencies, between 8 Hz and 10 kHz. The sensors’ response was...
-
Hotspot of human verbal memory encoding in the left anterior prefrontal cortex
PublicationBackground: Treating memory and cognitive deficits requires knowledge about anatomical sites and neural activities to be targeted with particular therapies. Emerging technologies for local brain stimulation offer attractive therapeutic options but need to be applied to target specific neural activities, at distinct times, and in specific brain regions that are critical for memory formation. Methods: The areas that are critical...
-
ZnO-decorated green-synthesized multi-doped carbon dots from Chlorella pyrenoidosa for sustainable photocatalytic carbamazepine degradation
PublicationThe promising green synthesis of carbon dots (CDs) from microalga Chlorella pyrenoidosa was achieved using simple hydrothermal and microwave-assisted methods. Doping of nanomaterials by nonmetals (N, S, and P) was confirmed by X-ray photoelectron spectroscopy (XPS), while the existence of metals in the CDs was confirmed by inductively coupled plasma optical emission spectroscopy (ICP-OES) and transmission electron microscopy (TEM),...
-
Experimental investigation of thermal energy storage in shell-and-multi-tube unit with nano-enhanced phase change material
PublicationThis paper deals with thermal energy storage with use of nanoparticle enhanced phase change material in shell-and-multitube unit. The experiments are conducted under atmospheric pressure. Paraffin wax and two different fatty acids are used as base phase change material. Graphite and multi-walled carbon nanotubes serve as nanoparticles. Graphite nanoparticles are tested at the concentrations of 0.1%, 1% and 5% by weight, while multi-walled...
-
Velocity Field Characteristics at the Inlet to a Pipe Culvert
PublicationA poorly designed culvert inlet structure causes scouring, which can lead to the collapse of the culvert and significant damage to the neighboring land. A set of laboratory tests was evaluated to examine velocity distribution at the culvert inlet. A three-dimensional acoustic Doppler velocimeterwas used to measure instantaneous flowvelocity upstream of the culvert. The analysis of mean velocities, turbulence strength, and Reynolds...
-
Experimental tests of reinforced concrete deep-beams
PublicationThe paper presents results of experimental research of the reinforced concrete deep beam with a spatial arrangement. Tested structural elements consist of the cantilever deep beam loaded on the height and transverse deep beam with hanging on it another one. The analysis includes crack morphology, effort of steel and load distribution. The article verified effectiveness of two different kind of reinforcement in both tested deep...
-
Application of Intuitionistic Fuzzy Sets to the assessment of technical university students
PublicationThe article proposes application of artificial intelligence methods to assess students of technical universities. The level of achieved educational goals can be assessed using measurements based on the idea of Fuzzy Intuitionistic Sets (IFS). A classification algorithm was developed and an exemplary distribution of the criteria values using IFS was presented. The application of the proposed approach in online education can enrich...
-
Enhancing Security of Advanced Metering Infrastructure by Introducing Threshold Attendance Protocol
PublicationThe industry pushes towards smart grid systems in order to resolve current limitations of the unidirectional legacy power grid infrastructure. By introducing Advanced Metering Infrastructure (AMI) as an integral part of the smart grid solution, the utility company obtains an invaluable tool to optimize its network, lower the operational costs, and improve quality of service. Unfortunately, introducing two-way communication poses...
-
Mid-infrared spectroscopy for characterization of Baltic amber (succinite)
PublicationNatural Baltic amber (succinite) is the most appreciated fossil resin of the rich cultural traditions dating back to prehistoric times. Its unequivocal identification is extremely important in many branches of science and trades including archeology, paleontology, chemistry and finally mineralogical and gemological societies. Current methods of modification of natural succinite are more and more sophisticated making the identification...
-
Night in a big city. Light festivals as a creative medium used at night and their impact on the authority, significance and prestige of a city
PublicationCities in times of global urbanization, are looking for completely new marketing methods, one such tool is the creative use of artificial light after dark, in the form of light festivals. This paper aims to introduce the historical development of the phenomenon and contemporary as well as contemporary illuminations / projects of illuminations of Fete des Lumieres festival in Lyon, Luminale in Frankfurt or on a smaller scale Lights...
-
Benchmarking overlapping communication and computations with multiple streams for modern GPUs
PublicationThe paper presents benchmarking a multi-stream application processing a set of input data arrays. Tests have been performed and execution times measured for various numbers of streams and various compute intensities measured as the ratio of kernel compute time and data transfer time. As such, the application and benchmarking is representative of frequently used operations such as vector weighted sum, matrix multiplication etc....
-
Using an IEEE1149.1 Test Bus for Fault Diagnosis of Analog Parts of Electronic Embedded Systems
PublicationThe new solution of a BIST called the JTAG BIST for self-testing of analog parts of electronic embedded systems is presented in the paper. The JTAG BIST consists of the BCT8244A and SCANSTA476 integrated circuits of Texas Instruments controlled via the IEEE 1149.1 bus. The BCT8244A is a scan test device with octal buffers, and the SCANSTA476 is a 12-bit ADC with 8 analog input channels. Self-testing approach is based on the fault...
-
Synthesis of novel dinuclear ruthenium polypyridine dye for dye-sensitized solar cells application
PublicationA new dinuclear ruthenium(II) polypyridine complex has been successfully synthesized. The new compound has been characterized by spectroscopic and electrochemical methods. Its potential application as a sensitizing dye in dye-sensitized solar cells has been checked under AM 1.5 G irradiation conditions (100 mW cm−2) and its performance was compared to that of a commercially available mononuclear analogous dye. The overall light-to-electricity...
-
Project Management Cycle in the Construction Industry Augmented by Collaborative Innovation Network Software
PublicationProject management is a very broad concept that has in recent times is growing rapidly. Management is especially complex in the construction sector, among the other sectors, due to the high uncertainty of workmanship and complexity of construction projects. Proper project management skills are an important factor in the success of projects, leading to reduced costs and shorten the time of investment. Nevertheless, most of the projects...
-
Effect of Tube Bundle Arrangement on the Performance of PCM Heat Storage Units
PublicationThe results of comprehensive study on charging and discharging of latent heat storage systems (LHSS) are presented. The multi tube shell-and-tube unit with a variable layouts of the tube bundles are examined. Two tube arrangements – in-line and staggered are tested. A variable number of tubes and different tube positions in a bundle are investigated. Moreover, two pitch ratios are studied. Three commercially available substances...
-
Active Learning Based on Crowdsourced Data
PublicationThe paper proposes a crowdsourcing-based approach for annotated data acquisition and means to support Active Learning training approach. In the proposed solution, aimed at data engineers, the knowledge of the crowd serves as an oracle that is able to judge whether the given sample is informative or not. The proposed solution reduces the amount of work needed to annotate large sets of data. Furthermore, it allows a perpetual increase...
-
Mobile devices and computing cloud resources allocation for interactive applications
PublicationUsing mobile devices such as smartphones or iPads for various interactive applications is currently very common. In the case of complex applications, e.g. chess games, the capabilities of these devices are insufficient to run the application in real time. One of the solutions is to use cloud computing. However, there is an optimization problem of mobile device and cloud resources allocation. An iterative heuristic algorithm for...