Search
Search results for: DROP-IN
-
Investigation of the thermal conductivity of λ gypsum using the hot wire method
Open Research DataAn experimental study was conducted to determine the thermal conductivity coefficient λ using the ‘hot wire’ method for a building material. Gypsum specimens measuring 400 x 60 x 50 mm were made for the experiment. Along the long axis of the model, an insulated resistance wire with a diameter of 0.2 mm was poured into the gypsum slurry in the centre...
-
ANALYSIS OF ROLLING RESISTANCE OF TIRES WITH RUN FLAT INSERT APPLYING DRUM METHOD AND RADIAL CHARACTERISTIC
PublicationThis paper presents analysis of rolling resistance of tires with RUN FLAT insert applying drum method and radial characteristic. The conducted studies indicated changes in operational properties of wheel, occurring as a result of inflation pressure drop in the wheel. As regards radial elasticity, such changes result in significant drop of radial rigidity and increase of static deflection and increase of tire rolling resistance....
-
The new concept of capillary forces aided evaporator for application in domestic organic rankine cycle
PublicationThis paper presents studies on the possibility of applying capillary forces induced in the porous structure to a modern design of evaporator. The potential application of such heat exchanger is for example an evaporator of the domestic micro combined heat and power (CHP) unit. One of the problems in the micro-CHP is excessive demand for pumping power. The proposed design helps in overcoming that issue. In the evaporator outlined...
-
Impulse Impedance Measurements of Lightning Protection Earthings
PublicationLightning protection earthing systems should be tested at currents with time parameters similar to those of lightnings. A method and definition of a measured value of impulse impedance are introduced. The impulse impedance was determined by a quotient of voltage drop on the tested earthing to a value of current in measure circuit. The usefulness of the impulse method for lightning protection evaluation is tested on radio base stations...
-
Numerical modeling of the combustion in a lab-scale pulverized-coal fired combustion chamber
PublicationThis work presents results of numerical modeling of the combustion process inside a lab-scale drop-tube chamber, designed to investigate the slagging properties of the flue ashes, created through the solid fuel firing. Interaction between turbulence and chemistry is accounted by use of probability density function (PDF). FLUENT inputs for non-premixed combustion chemistry modeling are defined. A discrete second phase of the coal...
-
Numerical modeling of the combustion in a lab-scale pulverized-coal fired combustion chamber
PublicationThis work presents results of numerical modeling of the combustion process inside a lab-scale drop-tube chamber, designed to investigate the slagging properties of the flue ashes, created through the solid fuel firing. Interaction between turbulence and chemistry is accounted by use of probability density function (PDF). FLUENT inputs for non-premixed combustion chemistry modeling are defined. A discrete second phase of the coal...
-
Impact response of two-layered grouted aggregate fibrous concretecomposite under falling mass impact
PublicationTwo-layered Grouted Aggregates Fibrous Concrete Composite (TGAFCC) is a new category concrete which became popular recently and attracted the attention of researchers globally. Recent studies indicated that TGAFCC has notable improvement in mechanical properties, which has been sufficiently documented. However, the impact behaviour of TGAFCC when combined with Glass Fibre Mesh (GFM) and Textile Fibre Mesh (TFM) is still unexplored....
-
A simple approach to heat exchanger sizing optimisation by means of entrophy generation minimisation
PublicationIn the paper an attempt is presented to find the method of optimization of microtube diameter with respect to optimal thermal-hydraulic conditions in the single-phase shell-and-tube heat exchangers. The approach is based on consideration of pumping power at the condition of maximum heat transfer by the heat exchanger tube system. In the optimization method the tube diameter is first specified and then appropriate calculations are...
-
The effect of agro-waste co-digestion and sludge disposal on carbon footprint in municipal wastewater treatment plants
PublicationThe study presents analysis of the carbon footprint (CF) in 6 wastewater treatment plants in northern Poland with a special focus on the effect of co digestion of sewage sludge and food waste. Although co-digestion increases the on-site energy production, but it has a negative effect on the total CF. To overcome the negative effect, several sludge disposal scenarios were analysed and their effect on the CF reduction was determined....
-
The protocol for using elastic wall model in modeling blood flow within human artery
PublicationMedical diagnostic tools will play a major role in the future for an effective patient treatment and reduction their mortality, related to the cardiovascular system diseases (CVDs). There is an urgent need for developing diagnostic procedure to be robust, reliable, accurate and efficient, in the framework of a paradigm shift. Application of numerical techniques is seen as a perspective tool for such purpose. Nevertheless, existing...
-
Parametric study of fluid flow and heat transfer over louvered fins of air heat pump evaporator
PublicationTwo-dimensional numerical investigations of the fluid flow and heat transfer have been carried out for the laminar flow of the louvered fin-plate heat exchanger, designed to work as an air-source heat pump evap- orator. The transferred heat and the pressure drop predicted by simulation have been compared with the corresponding experimental data taken from the literature. Two dimensional analyses of the louvered fins with varying...
-
Deciphering the Molecular Mechanism of Substrate-Induced Assembly of Gold Nanocube Arrays toward an Accelerated Electrocatalytic Effect Employing Heterogeneous Diffusion Field Confinement
PublicationThe complex electrocatalytic performance of gold nanocubes (AuNCs) is the focus of this work. The faceted shapes of AuNCs and the individual assembly processes at the electrode surfaces define the heterogeneous conditions for the purpose of electrocatalytic processes. Topographic and electron imaging demonstrated slightly rounded AuNC (average of 38 nm) assemblies with sizes of ≤1 μm, where the dominating patterns are (111) and...
-
Bias-Dependent Dynamics of Degradation and Recovery in Perovskite Solar Cells
PublicationDegradation of perovskite solar cells (PSCs) is often found to be partially or fully reversible when the cells are allowed to recover in the dark. Unlike the dynamics of degradation, knowledge about the dynamics of PSC cell recovery is very limited. Here, we demonstrate that the PSC recovery strongly depends on the electrical bias conditions during the light-induced degradation and that it can be manipulated by applying an external...
-
Thermal and economic investigation of straight and U-bend double tube heat exchanger with coiled wire turbulator
PublicationExperimental research has been carried out for four individual heat exchanger constructions, i.e., plain double tube, turbulized double tube, plain U-bend and U-bend with turbulator. Tests were made for the water-water system. The study covered a wide measuring range, i.e., Re = 800–9000 – on the shell side, for a constant cold water temperature of 9 ◦C and hot water of 50 ◦C. The heat exchangers were made from copper tubes with...
-
Comparison of Mathematical Models of Torque Transmitted by Multi-disc Wet Clutch with Experimental Results
PublicationIn this article was described the methodology for the experimental study of flows in the prototype of a satellite hydraulic motor with a rotating body. The experimental tests of the motor were carried out at a low constant rotational speed in a wide range of pressure drop in this motor. The constant rotational speed of the motor was kept by a worm gear. Based on the test results, the leakage characteristics in the flat gaps of...
-
Experimental Study of Flow Rate in Hydraulic Satellite Motor with the Rotating Case at a Low Constant Rotational Speed
PublicationIn this article was described the methodology for the experimental study of flows in the prototype of a satellite hydraulic motor with a rotating body. The experimental tests of the motor were carried out at a low constant rotational speed in a wide range of pressure drop in this motor. The constant rotational speed of the motor was kept by a worm gear. Based on the test results, the leakage characteristics in the flat gaps of...
-
Analysis of the Heating Process of Hydraulic Motors during Start-Up in Thermal Shock Conditions
PublicationConditions that prevail during harsh winters and hot summers pose a serious challenge for machine designers building devices suitable for operation in extreme weather. It is essential for the designers and the users to define the principles and conditions for the safe operation of machines and devices with hydraulic drive in low ambient temperatures. Bearing in mind the above, the author tested the hydraulic motors in thermal shock...
-
Influence of the low ambient temperature on the start-up process of hydraulic pumps
PublicationStarting hydraulic pumps in low ambient temperatures may cause: decreased hydraulic-mechanical efficiency, larger vibration of hydraulic installation, faster wear and more frequent damage to the elements of pumps, change of material properties of elements, increase of pressure drop. As a result of pressure drop in the suction pipe, large underpressure may be experienced, causing incomplete filling of pump working chambers with...
-
METHOD OF TRAINING THE ENDOSCOPIC VIDEO ANALYSIS ALGORITHMS TO MAXIMIZE BOTH ACCURACY AND STABILITY
PublicationIn the article a new training and testing method of endoscopic video analysis algorithms is presented. Classical methods take into account only eciency of recognizing objects on single video frames. Proposed method additionally considers stability of classiers output for real video input. The method is simple and can be trained on data sets created for other solutions. Therefore, it is easily applicable to existing endoscopic video...
-
Sensorless induction motor drive with voltage inverter and sine-wave filter
PublicationThis paper presents a speed sensorless control system of an induction motor with an output LC filter. It is known that the parameters design of the filter gives sine wave motor supply voltage but complicates control and estimation process. The reason is that the voltage drop and phase shift between filter input and output signals are imposed, and hence the motor voltages and currents differ from the inverter output waveforms. To...
-
Selected studies of flow maldistribution in a minichannel plate heat exchanger
PublicationAnalysis of the state of-the-art in research of minichannel heat exchangers, especially on the topic of flow maldistribution in multiple channels, has been accomplished. Studies on minichannel plate heat exchanger with 51 parallel minichannels with four hydraulic diameters, i.e., 461 μm, 574 μm, 667 μm, and 750 μm have been presented. Flow at the instance of filling the microchannel with water at low flow rates has been visualized. The...
-
High Performance Tubular Heat Exchanger with Minijet Heat Transfer Enhancement
PublicationIn the paper, the original cylindrical heat exchanger with minijets (MJHE) was introduced. The systematic experimental analysis of the prototype heat exchanger was described with special attention paid to such parameters as the heat transfer effectiveness, heat transfer rates, overall heat transfer coefficients, and pressure drop. The heat transfer coefficients were determined based on Wilson plot method, the most suitable approach...
-
Robust identification of quadrocopter model for control purposes
PublicationThe paper addresses a problem of quadrotor unmanned aerial vehicle (so-called X4-flyer or quadrocopter) utility model identification for control design purposes. To that goal the quadrotor model is assumed to be composed of two abstracted subsystems, namely a rigid body (plant) and four motors equipped with blades (actuators). The model of the former is acquired based on a well-established dynamic equations of motion while the...
-
NUMERICAL SIMULATIONS OF GAP FLOW ABOVE ROTATING DISK
PublicationA rotating disk can be considered a basic configuration for the investigati ons of the impact of various conditions on the flow through the clearance between the s hrouded turbine blade and the casing. Numerical calculations using Fine/Turbo Numeca were conducted to examine the influence of the rotational velocity and the pressure differ ence across the disk on the flow conditions, especially the mass flow through the clearance....
-
Analysis of cyclone separator solutions depending on SEC outlet conditions in nCO2PP
PublicationUtilization of spray ejector condenser in order to carry out direct-contact condensation of vapour with inert gas (CO2) on a spray of subcooled liquid integrated with separator (to make pure CO2) has been proposed for the task of condensation and CO2 separation in the negative CO2 emission gas power plant. Condensation and separation has a significant impact on the thermodynamic efficiency of the entire negative CO2 emission gas...
-
Occurrence and Levels of Biogenic Amines in Beers Produced by Different Methods
PublicationThe concentration of biogenic amines (BAs) in beer depends, among other factors, on the activity of microorganisms, in particular lactic acid bacteria. In this work an analytical method based on derivatization with tosyl chloride and high-performance liquid chromatography-tandem mass spectrometry (HPLC-MS/MS) was used to determine 17 BAs in samples of commercially available beers, and to monitor the changes in concentration of...
-
The study of structure and surface morphology of lithium titanate sol-gel derived thin films
PublicationIn this paper the structure and the surface morphology of lithium titanate (LTO) thin films are presented. Nanocrystalline thin films were prepared by sol–gel method. To examine the influence of the annealing time on as-prepared films crystallization, the coatings were heated at different temperatures in the range of 500 °C–600 °C for 10, 20, 40 and 80 h. The structure of the obtained material was investigated using the X-ray diffraction...
-
Ionic liquids in the microextraction techniques: the influence of ILs structure and properties
PublicationIonic liquids (ILs) are composed entirely of ions thus they possess unique properties, including negligible volatility, a liquid state in a broad range of temperatures and ability to change them depending on the chosen type of anion and cation, which make ILs unique and useful for many applications in sample preparation techniques. A deeper understanding of the nature of ILs and the impact of their structure on their parameters...
-
Insights Into Hydrodynamics of Spinning Fluids Reactor
PublicationSpinning fluids reactor (SFR) is one of the most efficient gas-liquid contacting system with high potential of application in many fields. The unique solution of SFR is the contacting of two spinning fluids which generated centrifugal force. The aim of this study was to investigate the pressure field distribution on the inner surface of reactors dispersing element. Obtained results confirm the high heterogeneity of the field pressure...
-
Ceramic composites for single-layer fuel cells
PublicationComposite materials consisting of acceptor doped lanthanum orthoniobate electrolyte phase (La0.98Ca0.02NbO4) and Li2O:NiO:ZnO semiconducting phase were synthesized. The precursor powder of La0.98Ca0.02NbO4 was prepared in nanocrystalline (mechanosynthesis) and microcrystalline (solid-state synthesis) form. The composite can be applied in a single-layer fuel cell, because of the presence of two phases acting as an anode and a cathode...
-
Effect of microstructure on mechanical properties and corrosion resistance of 2205 duplex stainless steel
PublicationThis paper presents results of the research on impact of microstructure of austenitic-ferritic steel of duplex type on its mechanical properties and susceptibility to stress corrosion cracking. As showed, improper processing technologies more and more often used in shipbuilding industry for plates and other half-finished products made of duplex steel may cause significant lowering their properties, which frequently makes their...
-
Structural and catalytic properties of ceria layers doped with transition metals for SOFCs fueled by biogas
PublicationThe aim of this paper was to investigate an influence of the nanocrystalline Ce0.8A0.2O2-δ (A = Mn, Fe, Co, Ni, Cu) materials on the direct internal reforming of biogas in SOFC. Structural analysis of fabricated compounds has been done. An in-situ analysis of a composition of outlet gases from operating SOFC was performed using FTIR spectroscopy with simultaneous electrical tests. It was found out, that type of dopant strongly...
-
The Influence of Thin Gold Electrodes on the High-Temperature Impedance of Oxide Glasses
PublicationThe influence of thin gold electrodes on the electrical measurements of glasses at high temperatures was studied using impedance spectroscopy. The impedance was measured several times over a wide frequency range from 10 mHz to 1 MHz and the temperature ranged from 213 to 673 K under air and nitrogen atmospheres. The results showed a drop in the conductivity of more than an order of magnitude at a temperature around 603 K during...
-
Selecting Features with SVM
PublicationA common problem with feature selection is to establish how many features should be retained at least so that important information is not lost. We describe a method for choosing this number that makes use of Support Vector Machines. The method is based on controlling an angle by which the decision hyperplane is tilt due to feature selection. Experiments were performed on three text datasets generated from a Wikipedia dump. Amount...
-
Analytical procedures for quality control of pharmaceuticals in terms of residual solvents content: Challenges and recent developments
PublicationResidual solvents play an important role in the synthesis of drugs and in product formulations. In addition, they pose a serious problem, that is toxicity, as many of them exhibit toxic or environmentally hazardous properties. Therefore, constant monitoring of quality control is needed. In this study, we present an overview of regulatory and general methods described by various pharmacopoeias. Then, the most commonly used methodologies...
-
STUDY ON THE EFFECTIVENESS OF THE TURBINE CONDENSER AIR EXTRACTION SYSTEM USING HYDRO EJECTORS
PublicationThe aim of the paper is to investigate the effectiveness of the 18K380 steam turbine condenser air extraction system using hydro ejectors. Motivation for the analysis is a need of improvement of the energy conversion ratio of the power plant. To achieve this goal it is necessary to establish efficiency of each subsystem of the energy cycle. The air extraction system is not a highly power consuming system but it has great impact...
-
Influence of operating pressure on the durability of a satellite hydraulic motor supplied by rapeseed oil
PublicationThis article describes the results of a durability test of a hydraulic satellite motor supplied by rapeseed oil. The tests were carried out on a test stand in a power recuperation system. The tests of the motor were carried out at a constant shaft speed for three fixed pressure drops in the motor. This made it possible to demonstrate the influence of the motor operating pressure on the durability of the satellite mechanism. The...
-
Improved model of isothermal and incompressible fluid flow in pipelines versus the Darcy–Weisbach equation and the issue of friction factor
PublicationIn this article, we consider the modelling of stationary incompressible and isothermal one-dimensional fluid flow through a long pipeline. The approximation of the average pressure in the developed model by the arithmetic mean of inlet and outlet pressures leads to the known empirical Darcy–Weisbach equation. Most importantly, we also present another improved approach that is more accurate because the average pressure is estimated...
-
Optoelectronic device for hematocrit measurements
PublicationAn optoelectronic system for measurements of hematocrit level (HCT) in the whole human blood is presented. Proposed system integrates a dedicated optoelectronic sensor, a microcontroller and a small LCD display in a low cost, battery-powered, handheld device. Chosen method for determining blood hematocrit level is based on optical properties of whole blood in visible and NIR wavelength range. Measurements with the use of proposed...
-
The Influence of Water and Mineral Oil on Pressure Losses in Hydraulic Motor
PublicationIn this paper, pressure losses in hydraulic motor supplied with water and mineral oil (two liquids that have significantly different viscosity and lubricating properties) are described and compared. The experimental tests were conducted using a hydraulic satellite motor that is dedicated to working with different liquids, including water. The methodology of measuring the pressure drop in internal channels of this motor is also...
-
The Method of Multi-criteria Analysis to Support the Decision on Load or Micro-generation Connection to a Low- or Medium-voltage Power Grid
PublicationThis paper presents a method that supports the decision in terms on selecting the best option of a load connection to a low- or medium-voltage power distribution grid, and of a micro-generation source connection to a low-voltage grid. The method is based on the search for the option with the lowest aggregate assessment measure, which is the weighted average of partial assessment measures determined for each of eight considered...
-
Investigation of natural frequencies of axially loaded thin-walled columns
PublicationThe paper deals with correlation between natural frequencies of two steel thin-walled columns and the corresponding applied load. The structures are made of cold-formed lipped channel sections. The columns lengths were assumed to follow two buckling patterns – global flexural and flexural-torsional buckling. In the thicker structure two material models were considered – linearly-elastic and elastic-perfectly plastic. Numerical...
-
Evaluation of Three Peptide Immobilization Techniques on a QCM Surface Related to Acetaldehyde Responses in the Gas Phase
PublicationThe quartz-crystal microbalance is a sensitive and universal tool for measuring concentrations of various gases in the air. Biochemical functionalization of the QCM electrode allows a label-free detection of specific molecular interactions with high sensitivity and specificity. In addition, it enables a real-time determination of its kinetic rates and affinity constants. This makes QCM a versatile bioanalytical screening tool for...
-
Light intensity analysis of photovoltaic parameters for perovskite solar cells
PublicationThe number of publications on perovskite solar cells (PSC) continues to grow exponentially. Although the efficiency of PSC is exceeded 25.5%, not every research laboratory can reproduce this result or even pass the border of 20%. Unfortunately, it is not always clear which dominating mechanism is responsible for the performance drop. Here, we develop a simple method of light intensity analysis of JV parameters allowing the understanding...
-
Copper Slag as a Potential Waste Filler for Polyethylene-Based Composites Manufacturing
PublicationThe present study aimed to analyze the application of waste material from copper production– copper slag (ŻŻL) as filler for composites based on the high-density polyethylene (HDPE). Copper slag filler was introduced in the amounts of 1–20 wt%, and its influence on the appearance (color analysis), chemical structure (Fourier-transform infrared (FTIR) spectroscopy), microstructure (optical microscopy), as well as static (tensile...
-
Crack propoagation in MgO-PSZ ceramic materials
PublicationThe properties of ceramic materials such as elevated hardness, high temperature capability, low coefficient of thermal expansion are of interest for rolling element materials. Widely used ceramic materials in engineering applications are silicon nitride, zirconia and alumina. The paper presents an experimental study of the fatigue life of MgO-PSZ ceramic material in lubricated contact with defined types of cracks. A ceramic angular...
-
Recuperator with microjet technology as a proposal for heat recovery from low-temperature sources
PublicationA tendency to increase the importance of so called dispersed generation, based on the local energy sources and the working systems uti- lizing both the fossil fuels and the renewable energy resources is observed nowadays. Generation of electricity on industrial or domestic scale together with production of heat can be obtained for example through employment of the ORC systems. It is mentioned in the EU directive 2012/27/EU for...
-
Manufacturing of Lightweight Aggregates as an Auspicious Method of Sewage Sludge Utilization
Publication: Sewage sludge is a high-volume and low-cost waste commonly generated worldwide, so its utilization is a vital issue. The application of this waste in the manufacturing of lightweight aggregates was investigated. The process was performed using intensive mixers with volumes of 5 and 30 L, as well as the industrial 500 L mixer. Then, granulates were sintered in a tube furnace. The influence of composition and mixer size on the...
-
Preparation and Characterization of Au/Pd Modified-TiO2 Photocatalysts for Phenol and Toluene Degradation under Visible Light—The Effect of Calcination Temperature
PublicationRutile loaded with Au/Pd nanoparticles was prepared using a water-in-oil microemulsion system of water/AOT/cyclohexane followed by calcination.Theeffect of calcination temperature (from350 to 700∘C) on the structure ofAu/Pd nanoparticles deposited at rutile matrix and the photocatalytic properties of Au/Pd-TiO2 was investigated in two model reactions (toluene degradation in gas phase and phenol degradation in aqueous phase). The...
-
Building a Nest by an Automaton
PublicationA robot modeled as a deterministic finite automaton has to build a structure from material available to it. The robot navigates in the infinite oriented grid $Z x Z$. Some cells of the grid are full (contain a brick) and others are empty. The subgraph of the grid induced by full cells, called the {\em field}, is initially connected. The (Manhattan) distance between the farthest cells of the field is called its {\em span}. The robot...