Filters
total: 11425
-
Catalog
displaying 1000 best results Help
Search results for: ENERGY AND EXERGY ANALYSIS
-
Review of hydrogen production technologies for automotive sector – thermodynamic analysis of energy and exergy losses
PublicationFew recent years has shown that hydrogen technology has a good chance to replace petroleum technology in automotive sector. However, hydrogen in pure form practically does not occur on Earth. That is why H2 form is used only as an energy carrier and it must be produced using another source of energy form water or hydrocarbon fuels. In this paper short overview of hydrogen production technology has been presented, with energy and...
-
Exergy analysis of the Szewalski cycle with a waste heat recovery system
PublicationThe conversion of a waste heat energy to electricity is now becoming one of the key points to improve the energy efficiency in a process engineering. However, large losses of a low-temperature thermal energy are also present in power engineering. One of such sources of waste heat in power plants are exhaust gases at the outlet of boilers. Through usage of a waste heat regeneration system it is possible to attain a heat rate of approximately...
-
HIERARCHICAL CYCLES IN MODERN POWER SYSTEMS – EXERGY ANALYSIS UNDER PART LOADS
PublicationThe aim of the paper is to investigate thermodynamic efficiency of advanced hierarchic power cyclesunder partial loads by using of exergy analyze. Advanced hierarchical power systems arecomposed of few energy conversion cycles, most common are steam and gas cycles in various configurations, but they may contain fuel cells, ORC, lithium bromide absorption chillers and others. Moreover hierarchical cycles can be powered by several...
-
Air-cooled photovoltaic roof tile as an example of the BIPVT system – An experimental study on the energy and exergy performance
PublicationThe air-cooled photovoltaic tile is a subject of presented investigations, which focused on improving the overall system efficiency of PV tiles with heat recovery. The operational efficiency of a PV roof tile, together with the construction optimising the air cooling efficiency, were the main points of plans realized at this research stage. The article describes the experimental research consisting of the assessment of electrical,...
-
Exergy and Energy Analyses of Microwave Dryer for Cantaloupe Slice and Prediction of Thermodynamic Parameters Using ANN and ANFIS Algorithms
PublicationThe study targeted towards drying of cantaloupe slices with various thicknesses in a microwave dryer. The experiments were carried out at three microwave powers of 180, 360, and 540 W and three thicknesses of 2, 4, and 6 mm for cantaloupe drying, and the weight variations were determined. Artificial neural networks (ANN) and adaptive neuro-fuzzy inference systems (ANFIS) were exploited to investigate energy and exergy indices of...
-
Exergetic Analysis of the nCO2PP Cycle with Particular Reference to the Exergy Destruction of Sewage Sludge Due to Gasification
PublicationAn exergy analysis is carried out on the negative CO2 emission gas power plant (nCO2PP), which integrates the process sections of fuel preparation, power generation and carbon capture. Processes of exergy destruction are studied with particular focus on the process in the gasification unit of the fuel preparation section, where a large amount of exergy is destroyed in various chemical reactions from sewage sludge to producer gas...
-
On energy, exergy, and environmental aspects of a combined gas-steam cycle for heat and power generation undergoing a process of retrofitting by steam injection
PublicationThe paper presents a study of retrofitting of a combined heat and power (CHP) plant aimed to increase the electric to heating power ratio. The modification would involve diverting part of the steam to the gas turbine, instead of letting it go to the steam turbine, using injection technique into a combustion chamber. Therefore, two potential retrofitting approaches are analyzed: steam injection gas turbine (STIGT) and combined steam...
-
ANALYSIS OF ENERGY EFFICIENCY IN ELECTRIC DRIVES
PublicationIn this paper energy efficiency in electric drives is analysed. This factor strongly depends on energy parameters - efficiency n and power factor k (in special case cos fi)
-
Energy Consumption Analysis Methods in Industry
PublicationThis paper overviews applied methods to evaluate energy consumption in Industry. The most important law regulations are presented, which decide on the necessity to conduct an effec - tive energetic economy. Basic assumptions are defined to calculate direct and cumulative energy consumption. The pros and cons of using each method are presented.
-
Exergy analysis of a negative CO2 emission gas power plant based on water oxy-combustion of syngas from sewage sludge gasification and CCS
PublicationA power cycle with water-injected oxy-combustion (water cycle) is investigated by exergy analysis. It is fueled with syngas (aka. producer gas) from gasification of sewage sludge. The cycle is equipped with a spray-ejector condenser (SEC). CO2 is separated and compressed for transportation and storage. The net delivered electric power is 31% of the fuel exergy. The task efficiency is 39% when the flue gas bleed to gasification...
-
Multiaspect measurement analysis of breaking energy recovery
PublicationNowadays the issue of electric energy saving in public transport is becoming a key area of interest, which is connected both with a growth of environmental awareness in the society and an increase in the prices of fuel and electricity. That is why the reduction of energy consumption by increasing electrified urban transport, such as trams, trolleybuses, light rail and underground is becoming an increasingly important issue. Energy...
-
Analysis of the interfacial energy of GaAs-Si hetrostructures
PublicationPrzeprowadzono obliczenia numeryczne energii powierzchni heterogranicy GaAs-Si z zastosowaniem półempirycznego modelu czteroparametrycznego Acklanda. Pokazano zależność energii heterogranicy od orientacji podłoża Si. Minima energetyczne otrzymano dla orientacji Si równych (011), (133), (112) i (113) co wskazuje ich zastosowanie do epitaksjalnego wzrostu warstw GaAs.
-
Thermodynamic analysis of the Compressed Air Energy Storage system coupled with the Underground Thermal Energy Storage
PublicationImprovement of flexibility is one of the key challenges for the transformation of the Polish Power System aiming at a high share of renewable energy in electricity generation. Flexible and dispatchable power plants will contribute to this ongoing transformation process as they compensate for fluctuations in electricity generation from renewable energy sources such as wind and photovoltaics. In this context, CAES storage tanks are...
-
Analysis of energy efficiency of suburban railway transport network
PublicationRising numbers of agglomeration residents cause increased need for people movement on daily basis. Because of congestion of local roads, air pollution and limited parking space, providing mass transit based on electric traction is reasonable. While the electric rail vehicles are considered highly efficient in themselves, they need to be analyzed as a part of a transport network, because energy consumption depends on operating conditions...
-
Analysis of start energy of Stirling engine type alpha
PublicationThe Stirling engine type alpha is composed of two cylinders (expansion space E and compression space C), regenerator that forms the space between the cylinders and the buffer space (under the pistons). Before the start-up and as a result of long-term operation, the average pressure in the working space (above the pistons) and in the buffer space is the same. However, in the initial phase of operation, the average pressure in the...
-
Analysis of spontaneous electrochemical oscillations by energy distribution technique
PublicationAnaliza niestacjonarnych oscylacji elektrochemicznych wskazuje na konieczność stosowania technik umożliwiających śledzenie zmian w czasie takich parametrów oscylacji jak częstotliwość, amplituda, pasmo częstotliwościowe. Algorytm prowadzący do uzyskania tych parametrów może być oparty o jeden z liniowych lub kwadratowych sposobów przedstawienia rejestru oscylacji w dziedzinie czasu i częstotliwości. W pracy autorzy przedstawiają...
-
Analysis of energy consumption at the Rzeszów Wastewater Treatment Plant
Publication -
Analysis of electrical energy consumption on the example of a selected building
Publication -
Nonradiative excitation energy transport and its analysis in concentrated systems
PublicationW pracy przedstawiono analizę transportu energii w roztworach dwuskładnikowych. Porównano wyniki pomiarów z modelem hoppingowym i diagramatycznym oraz z wynikami symulacji Monte Carlo. Stwierdzono dobrą zgodność wyników eksperymentalnych z przewidywaniami teorii i symulacjami komputerowymi.
-
A complete impedance analysis of electrochemical cells used as energy sources
PublicationA comprehensive description of impedance ofelectrochemical systems has been presented, along withthe assumptions of the method used. In this method, amultisinusoidal current excitation signal is used. Thechanges of potential of both the electrodes and thepotential difference between these electrodes are allregistered simultaneously as a function of time. Theproposed method offers the possibility of separatelydetermining the instantaneous...
-
Analysis of the Dependence between Energy Demand Indicators in Buildings Based on Variants for Improving Energy Efficiency in a School Building
Publication -
ENERGY ANALYSIS OF THE PROPULSION SHAFT FATIGUE PROCESS IN A ROTATING MECHANICAL SYSTEM PART III DIMENSIONAL ANALYSIS
PublicationThis article presents the third and last part of the problem of diagnosing the fatigue of marine propulsion shafts in terms of energy with the use of the action function, undertaken by the authors. Even the most perfect physical models of real objects, observed under laboratory conditions and developed based on the results of their research, cannot be useful in diagnostics without properly transferring the obtained results to the...
-
ISSUES OF ECONOMIC ANALYSIS OF ELECTRIC ENERGY GENERATION IN A FLOATING POWER PLANT
PublicationThis article presents basic dependences for conducting a technical and economic analysis related with investment projects. It describes a combined system of a compression ignition engine and a steam turbine, whose aim, when placed on a floating platform, is to generate electric energy in the so-called distributed generation system. Such a system involves a reciprocating internal combustion engine and a connected steam turbine system...
-
An analysis of solar energy conversion systems based on photon and thermal processes
PublicationSolar spectral irradiance covers a fairly broad wavelength range. Solar radiation is part of the electromagnetic spectrum which is described by the concept of wave-particle duality. The corpuscular theory of electromagnetic radiation states that energy is transmitted by photons. Photons carry specific amounts of energy which can be used to convert solar energy into other types of energy, in particular electricity. The internal...
-
Analysis of Crash Computation on a Basis of the Pronciple of Linear Momentum and Kinetic Energy
PublicationThe article shows the calculation of a vehicle crash with a fixed pile, modelled by the finite element method. There were compared during the crash simulations changes in kinetic energy, as well as – changes in linear momentum and its derivative, with respect to time. Calculations were made in the HyperWorks CAE software environment. The obtained results show influence of various body parts and devices of the deceleration on...
-
Utility analysis and rating of energy storages in trolleybus power supply system
PublicationThe article discusses two energy storage applications in power supply system of public electrified transport. The first application aims at reducing the peak power of the traction substation. The second application increases effectiveness of using solar power plant to cover partial power demand of traction supply system. These two applications were discussed and analyzed based on trolleybus supply system in Gdynia, where most measurements...
-
Collaborative development model and strategies of multi-energy industry clusters: Multi-indicators analysis affecting the development of coastal energy clusters
PublicationThe paper explores Coastal Energy-Based Industrial Clusters (EBICs) and their role in advancing energy efficiency and sustainability through collaborative innovation. Economic growth theory and energy sustainability have been introduced into industrial clusters to illustrate indicators that have a greater impact on the development of EBICs. This paper proposes an EBICs development model based on the Cobb-Douglas function, in which...
-
A unified approach to the analysis of electric energy and fuel consumption of cars in city traffic
PublicationForecasting fuel and electricity consumption is an important factor determining the direction of changes in road engineering solutions, traffic management, selection of routes for public transport and development more efficient car drive systems. With a reliable and easy-to-use computational tool, it is possible to reduce the consumption of primary energy sources and reduce the emission of toxic compounds in cities. An analysis...
-
Use of numerical methods in the analysis of traction energy systems—an overview of the practical examples
PublicationA characteristic feature of trolleybus transport is the random nature of traffic caused by congestion. It predestinates statistical and numerical methods for the analysis of trolleybus energy system. There are presented 3 methods of trolleybus traction system analysis: simulation of supply system based on Monte Carlo method, analysis of energy recovery potential based on statistical data analysis and benchmark of trolleybus supply...
-
Analysis of an Energy Management System of a Small Plant Connected to the Rural Power System
PublicationThis paper presents the analysis of an energy management system (EMS) implemented to fulfill the requirements of a microgrid (MG) power supply owned by a small industrial company and connected to the rural power system. The main goal of this system is to ensure connection with the existing rural power system in terms of energy exchange, as well as to perform islanding mode operation of the microgrid based on the energy demand of...
-
Design analysis of ORC micro-turbines making use of thermal energy of oceans
PublicationThe article presents the results of the analysis of energy conversion cycles making use of thermal energy of oceans. The objects of analysis were two cases of closed Organic Rankine Cycle (ORC) power plants, which were: the cycle in which the vapour of the working medium was produced by warm oceanic water in the circum-equatorial zone, and the so-called “arctic” cycle in which this vapour was produced by non-frozen water in the circumpolar...
-
Developing Novel Solutions to Realise the European Energy - Information Sharing & Analysis Centre
PublicationFor more effective decision making in preparation for and response to cyberevents in the energy sector, multilevel situation awareness, from technical to strategic is essential. With an uncertain picture of evolving threats, sharing of the latest cybersecurity knowledge among all sector stakeholders can inform and improve decisions and responses. This paper describes two novel solutions proposed during the formation of the European...
-
Numerical Analysis of Impact of Energy Buoy Anchoring Configurations on its Motion and Efficiency
PublicationThis paper presents a numerical analysis of the impact of energy buoy mooring configurations on its movement on the wave and effectiveness. The method used to analyse the buoy movement modelling in six degrees of freedom was described in a paper presented at the Conference 2011. Simulations of the buoy movement in regular wave and power calculations were conducted for several configurations of anchoring systems and position of...
-
Analysis of Business Customers’ Energy Consumption Data Registered by Trading Companies in Poland
Publication -
Efficiency analysis of an energy conversion system for a variable speed small hydropower plant
Publication -
Cogging torque analysis based on energy approach in surface-mounted PM machines
Publication -
Comprehensive thermodynamic analysis of the CAES system coupled with the underground thermal energy storage taking into account global, central and local level of energy conversion
PublicationA key aspect of CAES is the optimal configuration of the thermodynamic cycle. In this paper, the situation of cooperation between the current conventional power plants and wind farms is analyzed, and then, based on thermodynamic models, the process of storing thermal and electrical energy in the CAES system coupled with a heat storage and recovery is developed. Therefore, three levels can be distinguished, namely: the global level...
-
Energy savings by application of supercapacitor storage in trolleybus supplying station - analysis of experimental results
PublicationStorage devices can be divided into two groups: on-board energy storage devices, which are placed in the vehicles and off-board energy storage devices situated in traction substations or between them. Current research is focused mainly on two objectives. The first is to reduce the energy demand by introducing on-board energy storages in light electric vehicles like trams, trolleybuses or electrobuses. The latter is to provide a...
-
Ukrainian Market of Electrical Energy: Reforming, Financing, Innovative Investment, Efficiency Analysis, and Audit
PublicationThe aim of this research is to determine the influence of electrical energy market regulation reform in Ukraine on the competitive environment, the reproduction processes of financial and innovative support, and the energy efficiency of the national economy. The authors have put forward and verified the hypothesis that, under conditions of institutional maturity of the Ukrainian electrical energy market, its liberalization and...
-
Wind speed, wind direction and solar radiation datasets; wind and solar energy resources analysis
Open Research DataDataset contain the results of wind speed, wind direction and solar radiation for wind and solar energy resources analysis performed in years 2008 and 2009. Application for efficiency and profitability of solar and wind power plants anaylsis and for energy generation forecasting algorithms design and anaysis. Datasets used in doctoral dissertations,...
-
ENERGY SAVINGS BY APPLICATION OF SUPERCAPACITOR STORAGE IN TROLLEYBUS SUPPLYING STATION – ANALYSIS OF EXPERIMENTAL RESULTS
PublicationIn 2011–2013, stationary supercapacitor storage developed by the Electrotechnical Institute in Warsaw was put into trial operation in the trolleybus substation “Północna” (North) located in Gdynia. The article presents the results recorded during supercapacitor storage operation and discusses the impact of the storage on energy consumption savings. Guidelines for selecting a location for stationary supercapacitor storage...
-
Scenarios as a tool supporting decisions in urban energy policy: The analysis using fuzzy logic, multi-criteria analysis and GIS tools
Publication -
Förster Resonance Energy Transfer and Trapping in Selected Systems: Analysis by Monte-Carlo Simulations
PublicationMetoda symulacji Monte Carlo została opisana i zastosowana jako efektywne narzędzie do analizy wyników pomiarów transferu energii w wybranych układach, dla których zastosowanie podejścia analitycznego jest ograniczone lub nawet niemożliwe. Pokazano, że symulacja Monte Carlo pozwala obliczyć tzw. czynnik orientacyjny dla układów częściowo uporządkowanych oraz szereg innych wielkości ważnych do opisu zjawiska transferu energii, które...
-
Analysis of accumulation possibility of energy dissipated in the braking process of train driven by hybrid locomotive
PublicationW tradycyjnym procesie hamowania cała energia kinetyczna lub potencjalna pociągu napędzanego lokomotywą z silnikiem spalinowym jest rozpraszana do otoczenia w postaci energii cieplnej. W lokomotywach hybrydowych istnieje możliwość odzyskania części tej energii przez przekazanie jej do akumulatorów i ponowne wykorzystanie do napędu pociągu. W pracy przedstawiono model układu napędowego lokomotywy hybrydowej z silnikiem spalinowym,...
-
Analysis of energy recovery from surplus water pressure of municipal heat distribution network
Publication -
Technical and economic analysis of energy storage in the compressed air technology with low capacity for the production plant
PublicationCompressed air energy storage (CAES) system is a promising technology due to its numerous advantages, including relatively low maintenance cost, a long lifespan and high operational flexibility. This article explores the possibility of designing a CAES power plant as a source of electricity and heat for an existing industrial plant. The study involves the technical analysis of the power plant parameters and the economic analysis...
-
Performance of the AMOEBA Water Model in the Vicinity of QM Solutes: A Diagnosis Using Energy Decomposition Analysis
PublicationThe importance of incorporating solvent polarization effects into the modeling of solvation processes has been well-recognized, and therefore a new generation of hybrid quantum mechanics/molecular mechanics (QM/MM) approaches that accounts for this effect is desirable. We present a fully self-consistent, mutually polarizable QM/MM scheme using the AMOEBA force field, in which the total energy of the system is variationally minimized...
-
Analysis of stress and strains, forces and energy in initial contact zone abrasive grain with treating material
Publication -
Relationship among Economic Growth, Energy Consumption, CO2 Emission, and Urbanization: An Econometric Perspective Analysis
Publication -
Modular power converter with superconducting magnetic energy storage for electric power distribution system — Analysis and simulation
PublicationThis paper describes selected issues concerning realization of energy storage system (ESS) designed to operate in power distribution system. This paper presents a modular approach of 300 kVA power converter operating with superconducting magnetic energy storage (SMES), which gives high dynamics together with high power and suitable capability for instantaneous energy storage. Analysis and simulation studies of selected power converter...
-
Analysis of electricity generation variability in 2019 with special consideration of electrical energy generation from wind sources.
PublicationThis article presents issues related to the broadly understood development of wind energy. The state of the art of wind energy in the world has been discussed. This paper also shows issues related to factors affecting the development of renewable energy sources and their impact on the natural environment on the basis of available research. The focus is, however, on the critical analysis of phenomena in the data of the Transmission...
-
A New Approach of Solidification Analysis in Modular Latent Thermal Energy Storage Unit Based on Image Processing
PublicationThe solidification process of RT18HC in a cylindrical shell and tube storage unit has been studied using a new methodology based on image processing. The main idea of the algorithm is to label the region of solidification and use statistical functions to calculate the dimensions of the solidification front over time. Said analysis includes two methods. The first method is to measure the solid fraction changes during solidification....
-
Analysis of the selection of low-temperature medium for a turbine power plant using ocean thermal energy (OTEC)
PublicationThe paper presents the results and conclusions of numerical calculations modelled in the EES program of a closed OTEC cycle. The following mediums were analysed: ammonia, R32, R41, R404a, R407c, R410a, R423a, R500, R502, R507a and R114, R152a, R234fa, R600, R1234yf, R1234ze. Analogous assumptions were adopted as in the ORC cycle with heat regeneration for dry refrigerants without regeneration for wet refrigerants. Each of them...
-
Analysis of the selection of low temperature medium for a turbine power plant using ocean thermal energy (OTEC)
PublicationThe paper presents the results and conclusions of numerical calculations modelled in the EES program of a closed OTEC cycle. The following mediums were analysed: ammonia, R32, R41, R404a, R407c, R410a, R423a, R500, R502, R507a and R114, R152a, R234fa, R600, R1234yf, R1234ze. Analogous assumptions were adopted as in the ORC cycle with heat regeneration for dry refrigerants without regeneration for wet refrigerants. Each of them...
-
Analysis of the possibility of increasing thermal-electric energy conversion ratio in CHP units based on micro gas turbine
PublicationThe aim of this paper is to analyze the possibility of increasing thermal energy to electricity conversion efficiency in combined heat and power (CHP) units based on micro gas turbine during low heat demand periods. At the beginning sustainable development postulates under power engineering are explained. Next micro CHP as part of distributed generation idea is presented. The main part of the article is based on results of thermodynamic...
-
Energy Efficiency Analysis of Railway Turnout Heating With a Simplified Snow Model Using Classical and Contactless Heating Method
PublicationElectrical heating of railway turnouts is a considerable technical and economic challenge, hence the need to conduct research for optimisation of a railway turnouts heating system. This paper presents results of a numerical analysis and experimental research on heating systems mounted on rail turnouts in line with the classical method and including a heater thermally insulated from the base of a rail. The numerical calculations...
-
A finite element analysis of thermal energy inclination based on ternary hybrid nanoparticles influenced by induced magnetic field
PublicationThe use of hybrid nanoparticles to improve thermal processes is a key method that has implications for a variety of interventions utilized in many sectors. This paper aimed to look into the impacts of ternary nanoparticles on hyperbolic tangent materials to establish their thermal characteristics. Flow describing equations have been explored in the presence of heat production, non-Fourier heat flux, and an induced magnetic field....
-
MM/PBSA analysis of molecular dynamics simulations of bovine beta-lactoglobulin: free energy gradients in conformational transitions?
PublicationPraca dotyczy pH zależnych zmian konformacyjnych EF pętli beta-laktoglobuliny. Zmiany te są śledzone za pomocą metod obliczeniowych chemii (dynamika molekularna oraz metody MM/PBSA).
-
Estimation, optimization and analysis based investigation of the energy consumption in machinability of ceramic-based metal matrix composite materials
Publication -
The influences of the information and communication technology on the structural changes of Japanese energy sectors from 1985 through 2005: a statistical analysis
PublicationThe purpose of this study is to analyse the influences of information and communication technology (ICT) on the structural changes of Japanese energy sectors from 1985-2005. In this study, ICT is represented by two explanatory variables, namely: 1) computers, main parts and accessories; 2) telecommunications equipment. We employ a statistical tool in investigating the influences quantitatively, namely constrained multivariate regression...
-
Analysis and assessment of the acoustic emission suitability for determination of the energy states of a tribological system in the form of a four-ball tester friction node
PublicationThe present operating safety and cost reduction requirements of the compression ignition engines make it necessary to search for new methods of detecting their defects, e.g. by the analysis of acoustic emission signals coming from the slide bearings. The paper presents non-destructive measurements of acoustic emission (AE) in order to obtain information on the processes taking place in a tribological system under the continuously...
-
An analysis of the possibilities of increasing the production of electrical energy during the summer season by heat-generation back pressure turbine power units.
PublicationZbadano możliwości podniesienia mocy elektrycznej produkowanej przez przeciwprężne bloki ciepłownicze w sezonie letnim. Zbadano jedną z możliwości polegającą na dochładzaniu wody sieciowej powracającej z aglomeracji miejskiej. Zwrócono uwagę na aspekty techniczne, ekonomiczne i ekologiczne rozważanego rozwiązania.
-
Notch fatigue analysis and life assessment using an energy field intensity approach in 7050-T6 aluminium alloy under bending-torsion loading
PublicationThis paper studies the fatigue crack initiation and fatigue crack propagation of notched cylindrical bars made of 7050-T6 aluminium alloy subjected to multiaxial bending-torsion loading. The sites of crack initiation and the angles of crack initiation were successfully predicted from the distribution of the first principal stress at the notch surface. Fatigue crack initiation lives were computed through the new concept of energy...
-
Effects of Surface Energy and Surface Residual Stresses on Vibro-Thermal Analysis of Chiral, Zigzag, and Armchair Types of SWCNTs Using Refined Beam Theory
PublicationIn this article, vibration characteristics of three different types of Single-Walled Carbon Nanotubes (SWCNTs) such as armchair, chiral, and zigzag carbon nanotubes have been investigated considering the effects of surface energy and surface residual stresses. The nanotubes are embedded in the elastic substrate of the Winkler type and are also exposed to low and high-temperature environments. A new refined beam theory namely, one-variable...
-
ENERGY ANALYSIS OF PROPULSION SHAFT FATIGUE PROCESS IN ROTATING MECHANICAL SYSTEM PART I TESTING SIGNIFICANCE OF INFLUENCE OF SHAFT MATERIAL FATIGUE EXCITATION PARAMETERS
PublicationThe article discusses the problem of mathematical modelling of energy conversion processes in a rotating mechanical system for the purpose of identifying fatigue states of propulsion shafts in this system. A simplified physical model of the analysed system, constructed in an appropriate scale, has made the basis for the experimental research. The research programme took into consideration mechanical fatigue excitation of the model...
-
ENERGY ANALYSIS OF THE PROPULSION SHAFT FATIGUE PROCESS IN A ROTATING MECHANICAL SYSTEM PART II IDENTIFICATION STUDIES – DEVELOPING THE FATIGUE DURABILITY MODEL OF A DRIVE SHAFT
PublicationThe article presents a continuation of research carried out concerning identification of energy consequences of mechanical fatigue within a propeller shaft in a rotating mechanical system, while working under conditions of the loss of the required alignment of shaft lines. Experimental research was carried out on a physical model reflecting a full-sized real object: i.e., the propulsion system of the ship. It is proven, by means...
-
Relevance of the EU Structural Funds’ Allocation to the Needs of Combating Air Pollution in Poland. Analysis of the Operational Programmes of Regions Threatened With Critical Air Pollution from Distributed Energy Sources
PublicationRecent years, the European Environmental Agency, has been reporting air quality parameters in Poland, as the poorest among all the EU countries. Despite of adoption of the EU legislation on energy efficiency and energy performance of buildings, existing legal solutions occur insufficient in reducing air pollution in Polish regions. Lack of an effective schemes supporting complex thermal renovation of buildings, exchange of inefficient...
-
Analiza i ocena smarności olejów w ujęciu energetycznym i działania układu tribologicznego = Analysis and evaluation of oil lubricity from the viewpoint of energy apects and of the tribological system action
PublicationBased on measurement results, an interpretation is presented of the tribological system boundary layer action in the form of a four-ball tester friction node. The evaluation was performed of the boundary layer action understood as transfer of energy Ep resulting from loading the tribological system in a determined time t with work Lp, which may lead to breaking the boundary layer. That energy and time are the values unequivocally...
-
Looking for a minimum exergy destruction in hierarchical cycle
PublicationThe paper presents results of energy analysis, complemented with an exergy balance, of hierarchical thermodynamic cycle. Proposed cycle is a binary vapour cycle based on a model of real supercritical steam power plant. Energy analysis is used to preliminary optimization of the cycle and the exergy losses analysis is proposed to perform optimization of heat transfer processes, which are essential for hierarchical cycles. Proposed...
-
Exergy Losses in the Szewalski Binary Vapor Cycle
PublicationIn this publication, we present an energy and exergy analysis of the Szewalski binary vapor cycle based on a model of a supercritical steam power plant. We used energy analysis to conduct a preliminary optimization of the cycle. Exergy loss analysis was employed to perform a comparison of heat-transfer processes, which are essential for hierarchical cycles. The Szewalski binary vapor cycle consists of a steam cycle bottomed with...
-
Wpływ właściwości czynników chłodniczych na straty egzergii w pompie ciepła (Influence of Refrigerants Properties for Exergy Losses in Heat Pump)
PublicationArtykuł poświęcony jest wpływowi występujących w pompie ciepła strat egzergii na jej efektywność energetyczną, a co za tym idzie koszty funkcjonowania instalacji. Autorzy prezentują tu metodologię obliczeniową, która może być zastosowana w procesach projektowania układów cieplno-przepływowych. Obliczenia zostały wykonane na podstawie typowego układu powietrznej pompy ciepła pracującej w klimacie środkowo-europejskim. Ponadto w...
-
A Comparison of the Exergy Efficiencies of Various Heat-Integrated Distillation Columns
Publication -
WSPÓŁPRACA BLOKU GAZOWO-PAROWEGO Z OBIEGIEM ORC = Combinded power plant in cooperation with ORC
PublicationIn the paper presented is the idea of a combined gas and steam power plant cooperation with a low temperature organic Rankine cycle ORC unit. Considerations presented in the paper are accomplished for the Gorzów CHP. The intention of present analysis is heat recovery of low temperature energy and its further use in ORC cycle in order to produce electricity, without increase in fuel consumption. Waste energy is recovered from the...
-
Comparative study of a bottoming SRC and ORC for Joule–Brayton cycle cooling modular HTR exergy losses, fluid-flow machinery main dimensions, and partial loads
PublicationEnergy conversion efficiency increase in power plants with high-temperature gas-cooled reactors via implementation of the bottoming cycle was investigated under nominal and minimal thermal load of a high-temperature reactor (HTR). Heat transfer surface area and turbine outlet volumetric flow rate in bottoming cycles was also investigated. Water and two low-boiling point working fluids (ammonia and ethanol) were analyzed. Analyzed...
-
Jarosław Guziński prof. dr hab. inż.
PeopleJaroslaw Guzinski received M.Sc., Ph.D. and D.Sc. degrees from the Electrical Engineering Department at Technical University of Gdansk, Poland in 1994, 2000 and 2011 respectively. Since 2016 he is Associate Professor at Gdansk University of Technology. Currently he is the head of the Department of Electric Drives and Energy Conversion. From 2006 to 2009 he was involved in European Commission Project PREMAID Marie Curie, ‘Predictive...
-
Michał Mazur dr inż.
PeopleAktualne zainteresowania inżynieria mechaniczna, robotyka, drgania mechaniczne, analiza modalna, sterowanie, systemy czasu rzeczywistego Wybrane publikacje Kaliński K., Galewski M., Mazur M., Chodnicki M, 2017, Modelling and Simulation Of A New Variable Stiffness Holder for Milling Of Flexible Details, Polish Maritime Research, vol 24, ss. 115-124 Kaliński K. J., Mazur M.: Optimal control at energy performance index of the mobile...
-
Wprowadzenie do analiz egzergetycznych, PG_00059783
e-Learning CoursesThe aim of the course is to present the basic issues to carry out the balance of exergy and entropy in addition to the balance of mass and energy. To show the definition of the maximum work that a certain matter can do in a thermodynamic process when transitioning to equilibrium with its surroundings. To refer to chemical exergy and show the application of the exergy balance to define losses in a thermodynamic cycle.
-
Management of low-temperature heat source by ORC aided by additional heat source
PublicationThe presented work is aimed at utilisation of waste heat in the manner to produce electricity in ORC installation. Therefore the precondition of the study was to use the waste heat available in the form of a stream of hot water at 90°C. Such low enthalpy heat source is rather insufficient to produce a good quality vapour to feed the ORC turbine. That was the incentive to search for the ways of increasing the temperature of the...
-
Paweł Możejko dr hab.
People -
Ryszard Strzelecki prof. dr hab. inż.
People -
Zagospodarowanie ciepła odpadowego z biogazowych agregatów kogeneracyjnych w oczyszczalni ścieków = Waste heat utilisation from cogeneration set in sewage plant
PublicationW pracy opisano koncepcję współpracy biogazowych modułów kogeneracyjnych z niskotemperaturowym obiegiem parowym. Proponowana modernizacja pozwoliłaby na wykorzystanie entalpii fizycznej spalin, tym samym zwiększając sprawność urządzeń wytwarzających ciepło i energię elektryczną. Tego typu rozwiązanie umożliwiłoby częściowe pokrycie zapotrzebowania własnego na energię elektryczną, generując oszczędności w przedsiębiorstwie. W artykule...
-
Anna Danuta Dettlaff dr inż.
PeopleShe received her Master of Science degree in engineering with honours in 2013 at the Gdańsk University of Technology at the Department of Analytical Chemistry. In 2013-2017, she was a PhD student in the field of Chemical Technology at Faculty of Chemistry. Her doctoral dissertation was entitled “Nanocomposites based on conducting polymer and carbon materials for supercapacitor application”. In 2015, she was doing a three-month...
-
Michał Bernard Pietrzak dr hab.
PeopleMichal Pietrzak is head of the Department of Statistics and Econometrics at the Faculty of Economics and Management, Gdańsk University of Technology, and Deputy Editor-in-Chief for Statistical Reviewing of the journals: Oeconomia Copernicana and Equilibrium. Quarterly Journal of Economics and Economic Policy. Until October 2021, he worked as an associate professor at the Faculty of Economic Sciences and Management, Nicolaus...
-
Zagospodarowanie ciepła odpadowego z biogazowych agregatów kogeneracyjnych w oczyszczalni ścieków
PublicationW pracy opisano koncepcję współpracy biogazowych modułów kogeneracyjnych z niskotemperaturowym obiegiem parowym. Proponowana modernizacja pozwoliłaby na wykorzystanie entalpii fizycznej spalin, tym samym zwiększając sprawność urządzeń wytwarzających ciepło i energię elektryczną. Tego typu rozwiązanie umożliwiłoby częściowe pokrycie zapotrzebowania własnego na energię elektryczną, generując oszczędności w przedsiębiorstwie. W artykule...
-
Anna Kuczyńska-Łażewska dr inż.
PeopleAnna Kuczyńska-Łażewska graduated from the Faculty of Chemistry of the Gdańsk University of Technologyin the field of Chemistry (1st degree) and Environmental Protection Technologies, specialization: environmental protection systems (2nd degree). She completed an internship at the Leibniz-Institut für Katalyse in Rostock. She defended her doctorate in recycling of 1st and 2nd generation modules in 2018 at the Department of Energy...
-
Natalia Sokół dr inż.
PeopleBACKGROUND Master of Science in Light and Lighting (2008-2009/11) The UCL Bartlett School of Graduate Studies, Faculty of the Built Environment, London, UK, www.bartlett.ucl.ac.uk MA Degree in Interior Architecture (1999-2004), The Academy of Fine Arts, Poznan, Poland, www.uap.edu.pl MA Degree in Art Education (1997-2002), Academy of Fine Arts, Poznan, Poland, www.uap.edu.pl MAIN RESEARCH AREAS · ...
-
Surface Science - 2021/2022
e-Learning CoursesThe goal of the subject is the presentation of basic problems resulting from he existence of interfacebetween material objects and its surroundings. Discussion of the consequences arising from the existenceof surface energy. Analysis of possible applications of surface phenomena in technology. Understanding ofproblems and benefits resulting from decreasing dimensions of objects with the special emphasis on thesemiconductor band...
-
ENERGY
Journals -
Numerical methods in heat and fluid flow, PG_00057408
e-Learning CoursesReiteration of information on thermodynamic cycles and extension of information on their modelling using commercial software tools. Presentation of balances, constitutive equations, how to set up conditions in CFD type codes. Equipment regulation and control in the context of heat exchangers.Presentation of the computational capabilities of the CFD calculation code ANSYS Fluent. Mass, momentum and energy balances in 0D and 3D terms.Analysis...
-
Leszek Jarzębowicz dr hab. inż.
PeopleLeszek Jarzebowicz received the M.Sc., Ph.D. and D.Sc. degrees from Gdansk University of Technology (GUT), Poland, in 2005, 2010 and 2019, respectively. His research areas include control and modeling of electric drives, diagnostics of railway vehicles, analysis of energy efficiency in electrified transport, and microprocessor implementation of control algorithms. His teaching interests focus on electric vehicles, electrical engineering...
-
Charakterystyka energetyczna budynków mieszkalnych wielorodzinnych w perspektywie wymagań 2017-2021
PublicationOpracowanie zawiera analizę charakterystyki energetycznej przykładowego budynku mieszkalnego wielorodzinnego przeprowadzoną w perspektywie wymagań 2017-2021 r. Wskazano w niej elementy mające wpływ na zapotrzebowanie budynku na energię użytkową, końcową i nieodnawialną energię pierwotną (wskaźnik EP). Zidentyfikowano jednocześnie możliwe problemy ze spełnieniem wymagań określonych w przepisach techniczno-budowlanych oraz wskazano...
-
OCENA MOŻLIWOŚCI WYKORZYSTANIA CHARAKTERYSTYK ENERGETYCZNYCH PROCESU DO PRZEWIDYWANIA WSKAŹNIKÓW ENERGETYCZNYCH NA BIEŻĄCO
PublicationW artykule autorka zaprezentowała możliwości wykorzystania charakterystyk energetycznych procesu do bieżącej kontroli wskaźników energetycznych. Metoda bieżącej kontroli wskaźników wykorzystuje jako wartości porównawcze wskaźniki wyznaczane na podstawie charakterystyk energetycznych procesów. Metoda ma przede wszystkim mieć zastosowanie do wczesnego wykrywania i eliminowania nadmiernego, nieracjonalnego zużycia nośników energii...
-
Mohammad Hossein Ghaemi dr inż.
PeopleMohammad Hossein Ghaemi Mohammad Hossein Ghaemi (1967), is an Assistant Professor at the Faculty of Mechanical Engineering and Ship Technology - WIMiO (till 2020: Faculty of Ocean Engineering and Ship Technology), Department of Automatics and Marine Energy Engineering. He studied first at Tehran University, where was graduated in the field of Mechanical Engineering (Solid Mechanics). Then he received his MSc degree in the area...
-
Muhammad Jamshed Abbass Phd in Electrical Engineering
PeopleMuhammad Jamshed Abbass received the M.S. degree in electrical engineering from Riphah International University, Islamabad. He is currently pursuing the Ph.D. degree with the Wrocław University of Science and Technology, Wroclaw, Poland. His research interests include machine learning, voltage stability within power systems, control design, analysis, the modeling of electrical power systems, the integration of numerous decentralized...
-
Metody analizy energochłonności w przemyśle
PublicationBadania przeprowadzone w rozprawie doktorskiej pokazują nową ideę analitycznych metod analizy energochłonności w zastosowaniu do dużych odbiorców przemysłowych. Jej skuteczności dowodzono na przykładzie wybranego obiektu przemysłu spożywczego. Metoda ta jest rozwinięciem dotychczasowych metod wskaźnikowych. Autorską nowością jest wykorzystanie charakterystyk energetycznych procesów technologicznych do wyznaczania referencyjnych...
-
Możliwości ograniczenia zużycia energii napędowej urządzeń przez optymalizację doboru wymienników ciepła, właściwą konfigurację i kontrolę przepływu płynów roboczych
PublicationArtykuł poświęcony możliwości ograniczenia zużycia energii napędowej urządzeń na drodze optymalizacji doboru wymienników ciepła, właściwej konfiguracji i kontroli przepływu płynów roboczych. Przedstawiono w nim ocenę zużycia energii w systemach energetycznych o największej energochłonności w realiach Polski. Zwrócono uwagę na możliwość wykorzystania wymienników ciepła o wysokiej efektywności dla zmniejszenia oporu przenoszenia...
-
Mathematical and numerical modelling,W,IDE-EMSS,IIst,sem.01,lato,2023/24 (PG_00057379)
e-Learning CoursesModelling of controlled mechanical systems by the mixed method of rigid and flexible finite elements: The finite element volume problems. Dynamics of multibody systems. Modelling of stationary closed loop systems. Modelling of systems whose configuration changes with time. Modelling of nonlinear controlled systems. Optimal control at energy performance index: Control of continuous nonstationary systems in domain of generalised...
-
Mathematical and Numerical Modelling, L, IDE IInd, sem.01, summer, 2022/23(00057379)
e-Learning CoursesModelling of controlled mechanical systems by the mixed method of rigid and flexible finite elements: The finite element volume problems. Dynamics of multibody systems. Modelling of stationary closed loop systems. Modelling of systems whose configuration changes with time. Modelling of nonlinear controlled systems. Optimal control at energy performance index: Control of continuous nonstationary systems in domain of generalised...
-
Strength of Materials Towards Applications (2024)
e-Learning CoursesThe SMTA DATE Course consists of the following problems to be discussed during the lectures: - Introduction to strength of materials towards applications - Fundamentals of modelling in strength of materials towards applications - Materials and basic structures - Fundamentals of modelling in strength of materials towards applications - Definition of environment and loads - General, energy-based and advanced methods for analysis...
-
Tomasz Krolikowski dr hab. inż.
PeopleIn 1996, I have graduated from the Faculty of Marine Science of Szczecin University and obtained a master's degree - ocean engineering engineer " - Control and Ocean Engineering Measurements". In 1994 I was hired as an assistant trainee at the Institute of Computer Science Technical University of Szczecin, and after graduating in 1996, I was employed as academic and teaching at the Institute of Computer Science in the Department...