Search
Filters
total: 257
Search results for: LOSSES ANALYSIS
-
Driving a new perspective Professor Zygmunt Paszota, faculty of ocean engineering and ship technology, Gdansk University of Technology, Poland, explains a new approach to the Sankey Diagram for drive motors
PublicationThe paper presents the necessity of replacing the traditional, commonly accepted but erroneous, Sankey diagram of power decrease in the direction of power flow by the diagram, proposed by the Author, of power increase in the direction opposite to the direction of power flow. The proposed view of losses and energy efficiency should be applied to all types of drive motors and drive systems. The presented proposals open a new perspective...
-
Empirical Relationship Describing Total Convective and Radiative Heat Loss in Buildings
PublicationOn the basis of theoretical considerations of convective-radiative heat transfer, a relationship was developed enabling the total convective and radiative heat flux QC+R emitted from any object at tw and its surroundings at t∞ to be calculated from known values of the surface temperature of such an object, i.e., the known temperature difference Δt=tw - t∞ and average air temperature Tav. This relationship is applied to thermal...
-
Role of surface recombination in perovskite solar cells at the interface of HTL/CH3NH3PbI3
PublicationIn order to achieve the highest performance of organometal trihalide perovskite solar cells, it is required to recognize the dominant mechanisms which play a key role in a perovskite material. In the following studies, we have focused on the interfacial recombination between the hole transporting layer (HTL) and the perovskite CH3NH3PbI3 in solar cell devices with p–i–n architecture. It has been shown that Cu:NiOx : used as HTL...
-
Modeling of Electrified Transportation Systems Featuring Multiple Vehicles and Complex Power Supply Layout
PublicationThe paper proposes a novel approach to modeling electrified transportation systems. The proposed solution reflects the mechanical dynamics of vehicles as well as the distribution and losses of electric supply. Moreover, energy conversion losses between the mechanical and electrical subsystems and their bilateral influences are included. Such a complete model makes it possible to replicate, e.g., the impact of voltage drops on vehicle...
-
Novel microstrip low-pass filters with fractal defected ground structures
PublicationIn this study, three microstrip low-pass filters (LPFs) containing fractal-shaped defected ground structures have been designed and manufactured. To improve the performance of microstrip LPF, cascades of inductively coupled fractal resonators have been applied. Simultaneously, to achieve relatively constant microstrip impedance resulting in essentially low reflection losses, a modification of the strip geometry has been introduced....
-
Hysteresis curves for some periodic and aperiodic perturbations in gases
PublicationEvolution of sound in a medium whose properties irreversibly vary in the course of wave propagation, is studied. For example, a gas that is a particular case of a Newtonian fluid is considered. Hysteresis curves, pictorial representations of irreversible attenuation of the sound energy, in the plane of thermodynamic states are plotted. The irreversible losses in internal energy are proportional to the total attenuation and depend...
-
Cross-border transmission line configuration influence on the electrical power and energy billing process
PublicationIn 2015 a connection between the Polish and Lithuanian power systems become fully operational. The connection consists of a 400 kV double circuit transmission line and a back-to-back HVDC substation located on the Lithuanian side. A magnetic couplings between the circuits of the transmission line cause that during power transmission a different values of active power losses are observed in both circuits. This situation may cause...
-
On bidirectional preestimates and their application to identification of fast time-varying systems
PublicationWhen applied to the identification of time-varying systems, such as rapidly fading telecommunication channels, adaptive estimation algorithms built on the local basis function (LBF) principle yield excellent tracking performance but are computationally demanding. The subsequently proposed fast LBF (fLBF) algorithms, based on the preestimation principle, allow a substantial reduction in complexity without significant performance...
-
The influence of road surface unevenness on tyre rolling resistance
PublicationThe geometric characteristics of road surface substantially affect the interaction between tyre and road. Depending on pavement texture wavelength, the texture chiefly affects tyre/road friction, rolling resistance, interior and exterior noise, tyre wear, and ride comfort. The article presents results of investigations on the influence of road surface unevenness on the rolling resistance of passenger car and truck tyres. The tests...
-
Benchmarking Parallel Chess Search in Stockfish on Intel Xeon and Intel Xeon Phi Processors
PublicationThe paper presents results from benchmarking the parallel multithreaded Stockfish chess engine on selected multi- and many-core processors. It is shown how the strength of play for an n-thread version compares to 1-thread version on both Intel Xeon and latest Intel Xeon Phi x200 processors. Results such as the number of wins, losses and draws are presented and how these change for growing numbers of threads. Impact of using particular...
-
Concept of managing quality in baking industry, in vector representation
PublicationThe author introduced an innovative metrisable method of describing a manufacturing process. The idea of vector structure of a manufacturing process allows to formulate quantitative relations between the activity of input streams, elements of product quality, and measurable effects of losses. The structure was basis for the formulation of the concept of the process of managing product quality in the baking industry in a vector...
-
Facial data registration facility for biometric protection of electronic documents
PublicationIn modern world, information is crucial, and its leakage may lead to serious losses. Documents as the main medium of information must be therefore highly protected. Nowadays, the most common way of protecting data is using passwords, however it seems inconvenient to type complex passwords, when it is needed many times a day. For that reason a significant research has been conducted on biometric authentication...
-
Immunogenic and protective activity of recombinant chimeric Toxoplasma gondii proteins
PublicationToxoplasmosis, one of the most common parasitic invasions worldwide, may pose a great threat for individuals with weakened immune system. The parasite also causes considerable economic losses due to infection of livestock. To date there is no efficient immunoprophylaxis for humans and animals, which would provide long-lasting protection against T. gondii invasion. Chimeric proteins, containing several selected fragments of parasite...
-
Accurate electrothermal modelling of high frequency DC-DC converters with discrete IGBTs in PLECS software
PublicationIn the paper, a novel, improved method of the IGBT junction temperature computations in the PLECS simulation software is presented. The developed method aims at accuracy of the junction temperature computations in PLECS by utilising a more sophisticated model of transistor losses, and by taking into account variability of transistor thermal resistance as a function of its temperature. A detailed description of the proposed method,...
-
Damage Development on the Surface of Nickel Coating in the Initial Period of Erosion
PublicationThe common occurrence of the phenomenon of cavitation in many industries and the multitude of factors affecting the resistance to cavitation erosion of used materials contribute to the search for methods and appropriate parameters of coating application that are able to minimize the effects of erosion. To determine the validity of the developed application parameters and the method used, cavitation studies and microscopic observations...
-
Unusual streaming in chemically reacting gases
PublicationNonlinear stimulation of the vorticity mode caused by losses in the momentum of sound in the chemically reacting gas, is considered. The instantaneous dynamic equation which describes the nonlinear generation of the vorticity mode, is derived. It includes a quadratic nonlinear acoustic source. Both periodic and aperiodic sound may be considered as the origin of the vorticity flow. In the non-equilibrium regime of the chemical reaction,...
-
Environmentally acceptable lubricants (EAL) compared with a reference mineral oil as marine stern tube bearing lubricant – Experimental and theoretical investigations
PublicationThe purpose of this research is to indicate the potential differences in bearing characteristics resulting from the application of different lubricant types with the same viscosity grade. The effect of different environmentally acceptable lubricants (EALs) on hydrodynamic journal bearing properties is studied experimentally and compared to the properties obtained after lubrication with a reference mineral oil. The results of the...
-
Time variable gain for long range sonar with chirp sounding signal
PublicationThe main purpose of applaying Time Variable Gain (TVG) in active sonars with digital signal processing is to reduce dynamic range of echo signal and adapt it to the dynamic range of the analogue to digital conversion. With high transmission losses level, the dynamic range of the input signal in long range sonars can be very high and even exceed 200dB. When chirp sounding signals with matched filtration are used, sonars can raech...
-
Hysteresis curves and loops for harmonic and impulse perturbations in some non-equilibrium gases
PublicationEvolution of sound in a relaxing gas whose properties vary in the course of wave propagation, is studied. A relaxing medium may reveal normal acoustic properties or be acoustically active. In the first case, losses in acoustic energy lead to an increase in internal energy of a gas similarly as it happens in Newtonian fluids. In the second case, acoustic energy increases in the course of sound propagation, and the internal energy...
-
Diagnosing marine turbine engines through energy characteristics of their flow section
PublicationThe aim of the performed research was to develop of diagnostic method of the flow section of a marine turbine combustion engine based on the level of delamination of its energy characteristics. The here adopted diagnostic model provides for a formulation of the evaluation of the technical conditions based on the measurements of the parameters of the thermodynamic medium in the characteristic control cross-sections of the engine...
-
Satellite pump and motor
PublicationThe article describe the design and operation of a prototype of satellite pump and a prototype of satellite motor. In both machines, the operating mechanism consists of a non-circular gear with external teeth (rotor), non-circular gear with internal teeth (curvature), and ten gear wheels which cooperate with the rotor and the curvature. The differences between the commutation unit in the pump and the commutation unit in the motor...
-
A comparative performance assessment of a hydrodynamic journal bearing lubricated with oil and magnetorheological fluid
PublicationThis work presents the investigation results of a journal bearing lubricated with magnetorheological fluid that is activated by a local constant magnetic field to vary both the local flow resistance and pressure. The bearing performance is assessed via Finite Element Modelling (FEM) and results are corroborated by experiments. The FEM model uses the Bingham model to describe the fluid film. A dedicated test rig is used to assess...
-
Reinforced Secure Gossiping Against DoS Attacks in Post-Disaster Scenarios
PublicationDuring and after a disaster, the perceived quality of communication networks often becomes remarkably degraded with an increased ratio of packet losses due to physical damages of the networking equipment, disturbance to the radio frequency signals, continuous reconfiguration of the routing tables, or sudden spikes of the network traffic, e.g., caused by the increased user activity in a post-disaster period. Several techniques have...
-
Microstrip four-port circulator using a ferrite coupled line section
PublicationThis paper describes an alternative configuration of a four-port circulator realized in a microstrip ferrite coupled line technology. The proposed fully planar device employs two three-port circulators consisting of a ferrite coupled line junction and T junction. Both circulators are connected through the same arm, hence, the problem of anti-parallel magnetization met in this type of circulators is avoided without the increase...
-
Voltage and frequency regulation of a standalone induction generator by reduced-rating power electronic compensators - comparative evaluation
PublicationIn this paper are considered two fundamental topologies of power electronic compensators for voltage and frequency control of a standalone self-excited induction generator (IG) system. These are voltage and current source inverter based shunt compensators with energy storage. The aim of this study is to assess main features of both topologies in dynamic and steady-state IG operation. The whole system is modelled with the aid of...
-
REAL-TIME VOICE QUALITY MONITORING TOOL FOR VOIP OVER IPV6 NETWORKS
PublicationThe primary aim of this paper is to present a new application which is at this moment the only open source real-time VoIP quality monitoring tool that supports IPv6 networks. The application can keep VoIP system administrators provided at any time with up-to-date voice quality information. Multiple quality scores that are automatically obtained throughout each call reflect influence of variable packet losses and delays on voice...
-
Influence of Phase Composition on Dielectric Properties of Bismuth-Based Ceramics with Scheelite-Type Structure
PublicationGoal of the present research was to study dielectric properties of BiNbO4 ceramics fabricated by solid state reaction route followed with pressureless sintering. The samples were fabricated from the mixture of oxides, viz. Nb2O5 and Bi2O3. Apart from stoichiometric amount an excess of 3%, 5% and 10% by mole of Bi2O3 was used. It was found that an excess amount of Bi2O3 oxide caused formation of Bi5Nb3O15 minor phase in amount of...
-
Augmented speed control scheme of dual induction motors with mutual flux angle control loop
PublicationThis paper proposes an augmented speed control scheme of dual induction motors fed by a five-leg voltage source inverter (VSI) with a common/shared-leg. An additional control loop is proposed here and based on the mutual flux angle – the difference between flux angular positions of the IMs. The main purpose of this research is to minimize the energy losses in the common inverter leg by controlling the mutual flux angle, at equal...
-
Application of vertical flow constructed wetlands for highly contaminated wastewater treatment: preliminary results
PublicationBasing on quantitative and qualitative characteristics of reject waters (RWC) generated during dewatering of digested sewage sludge on centrifuges in conventional WWTP and municipal landfill leachate (LL), the pilot constructed wetlands for treatment of both types wastewater were designed and built. In the paper the conception, design and assumed treatment efficiencies of the pilot plants are presented. The water balance of the...
-
Innovative Railway Stations
PublicationIn relation to modern demographic trends, evolving technologies and environmentfriendly solutions increases the potential of rail considered as sustainable form of public transport. Contemporary tendencies of designing railway stations in Europe are focused on lowering energy consumption and reducing carbon emission. The main goal of the designers is to create a friendly and intuitive space for its users and at the same time a...
-
Performance of a single layer fuel cell based on a mixed proton-electron conducting composite
PublicationMany of the challenges in solid oxide fuel cell technology stem from chemical and mechanical incompatibilities between the anode, cathode and electrolyte materials. Numerous attempts have been made to identify compatible materials. Here, these challenges are circumvented by the introduction of a working single layer fuel cell, fabricated from a composite of proton conducting BaCe0.6Zr0.2Y0.2O3-δ and a mixture of semiconducting...
-
Susceptibility to Degradation in Soil of Branched Polyesterurethane Blends with Polylactide and Starch
PublicationA very important method of reducing the amount of polymer waste in the environment is the introduction to the market of polymers susceptible to degradation under the influence of environmental factors. This paper presents the results of testing the susceptibility to degradation in soil of branched polyesterurethane (PUR) based on poly([R,S]-3-hydroxybutyrate) (R,S-PHB), modified with poly([D,L]-lactide) (PLA) and starch (St). Weight...
-
A new technology of crude vegetable oil degumming with rhamnolipid solutions
PublicationA new technology of crude vegetable oil degumming is described. It is based on rhamnolipid biocomplex solution application for phosphatides removal. The rhamnolipid biocomplex produced by Pseudomonas sp. PS-17 was used as biosurfactant. Rapeseed oil was used in all experiments. First, it was degummed with H2SO4 in order to remove all phosphatides and then 1% (w/w) of granular soybean lecithin was added. Model oil was treated with...
-
Development of tools for road infrastructure safety management for the provinces (voivodeships) in Poland
PublicationThe development of modern tools for road infrastructure safety management will help to reduce the number of fatalities and serious injuries as one of the main objectives adopted in 2013 in the National Road Safety Programme 2014-2020 and the new Road Safety Programme 2011-2020 in the EU. Risk Management in Highway Engineering can be applied in developing tools essential in the process of safety management. Risk Management in Highway...
-
Effect of MAO coatings on cavitation erosion and tribological properties of 5056 and 7075 aluminum alloys
PublicationTwo ceramic coatings have been applied on 5056 and 7075 aluminum alloy by microarc oxidation (MAO) technology. The mass losses, surface morphologies and the phase constituents of the MAO coatings before and after cavitation tests were examined by means of digital scales, scanning electron microscopy (SEM) and X-ray diffraction (XRD), respectively. In order to assess the impact of the mechanical properties of the surface layer on...
-
Constant vs. Variable Efficiency of Electric Drive in Train Run Simulations
PublicationTrain run simulations, which focus on various power- and energy-oriented aspects, should reflect the losses in the electric powertrain. In general, the powertrain efficiency varies with respect to load and speed. Including this relation in simulation requires knowledge about detailed drivetrain parameters, which are often unavailable. This paper verifies the possibility to approximate the drivetrain efficiency in train run simulations...
-
Determination of Pesticide Residues in Honeybees using Modified QUEChERS Sample Work-Up and Liquid Chromatography-Tandem Mass Spectrometry
PublicationIncreasing emissions of chemical compounds to the environment, especially of pesticides, is one of factors that may explain present honeybee colony losses. In this work, an analytical method employing liquid chromatography-tandem mass spectrometry (LC-MS/MS) was optimized for the simultaneous screening of 19 pesticides which have not been yet determined in honeybee samples from northern Poland (Pomerania). The sample preparation,...
-
Magnetoacoustic Heating in Nonisentropic Plasma Caused by Different Kinds of Heating-Cooling Function
PublicationThe nonlinear phenomena which associate with magnetoacoustic waves in a plasma are analytically studied. A plasma is an open system with external inflow of energy and radiation losses. A plasma’s flow may be isentropically stable or unstable. The nonlinear phenomena occur differently in dependence on stability or instability of a plasma’s flow. The nonlinear instantaneous equation which describes dynamics of nonwave entropy mode...
-
Effect of Simultaneous Valve Closures in Hydraulic Piping Systems
PublicationThe paper investigates wave interference (between pressure waves) occurring in simple hydraulic systems. Water hammer was induced by simultaneous closure of three valves located at the reservoirs of a “Y” type hydraulic system. Numerical simulations were carried out with the help of the freeware computer package Allievi enabling the reader to replicate results in a direct manner. The influence of the following quantities has been...
-
Determination of the theoretical and actual working volume of a hydraulic motor
PublicationA new methodology of determination of the theoretical and actual working volume of a hydraulic motor based on the characteristics of the delivered flow rate into hydraulic motor vs. the rotational speed at a constant pressure drop in the working chambers is described in this paper. A new method of describing the delivered flow rate into a motor per one shaft revolution as a nonlinear function of the pressure drop in the motor working...
-
Assessing the Risk in Urban Public Transport for Epidemiologic Factors
PublicationPandemics have presented new challenges for public transport organisers and operators. New diseases (e.g., influenza H1N1, severe acute respiratory syndrome—SARS, as well as, more recently, SARS-CoV-2) increase the need for new protection measures to prevent epidemic outbreaks in public transport infrastructure. The authors’ goal is to present a set of actions in the area of public transport that are adjusted to different levels...
-
Engineering method of tire rolling resistance evaluation
PublicationTire rolling resistance is one of the most difficult tire parameters to measure. The reason is that for modern tires the force of rolling resistance corresponds to 0.5–1% of tire load, thus measurements of very small forces must be performed in a heavily loaded system. This constitutes great problems, especially in road conditions. Laboratory measurements are easier to perform, as the environment may be better controlled, but roadwheel...
-
Performance Evaluation of a 650V E-HEMT GaN Power Switch
PublicationGaN power switches have better characteristics compared to the state-of-the-art Si power transistors. These devices offer high operating temperature and current densities, fast switching and low on-resistance. However, currently only a few producers offer technology of high voltage GaN transistors. Immaturity of this technology is the reason why experimental evaluation of GaN parameters must be performed to properly exploit their...
-
Friction and Lubrication of Large Tilting-Pad Thrust Bearings
PublicationFluid film bearings have been extensively used in the industry because of their unbeatable durability and extremely low friction coefficient, despite a very low coefficient of friction dissipation of energy being noticeable, especially in large bearings. Lubricating systems of large tilting pad thrust bearings utilized in large, vertical shaft hydrogenerators are presented in this paper. A large amount of heat is generated due...
-
Ecology In Tribology: Selected Problems of Eliminating Natural Oil-Based Lubricants from Machine Friction Couples
PublicationThe elimination of mineral oil-based lubricants from machines has multiple beneficial effects on the natural environment. Firstly – these lubricants are a direct threat to the environment in the event of leaks; secondly – their elimination reduces the demand for crude oil from which they are obtained. In addition, in many cases, e.g. when replacing traditional lubricants with water, friction losses in the bearings can also be reduced...
-
The efficiency of turbomachinery in the zero-and three-dimensional approaches
PublicationEfficiency of turbomachinery is usually defined using an isentropic process. This approach provides a reliable reference point only when pressure and temperature measurements are available, e.g. at the casing inlet and outlet. In the case of a single stage internal efficiency determination the reference point is difficult. Computational fluid dynamics allows for an exact calculation of values of losses occurring in a turbine...
-
Determination of the Theoretical and Actual Working Volume of a Hydraulic Motor—Part II (The Method Based on the Characteristics of Effective Absorbency of the Motor)
Publication: In this article, the second method of determination of the theoretical and actual working volume of a hydraulic motor is described. The proposed new method is based on the characteristics of effective absorbency of the motor. The effective absorbency has been defined as the ratio of flow rate in a motor to the rotational speed of the motor’s shaft. It has been shown that the effective absorbency is a nonlinear function of the...
-
A New Microwave Ceramic – Polymer Composite with 0-3 Connectivity
PublicationGoal of the present research was to fabricate and study two-phase BiNbO4//PVDF composites with 0-3 connectivity. Such composite consists of there-dimensionally connected polymer matrix loaded with dielectric ceramic particles. In the present case BiNbO4 powder acted as an active phase (dispersed phase) whereas polyvinylidene fluoride (PVDF) acted as a non-active (passive) phase (matrix). BiNbO4//PVDF composites with the volume...
-
LEAN MANAGEMENT IN HIGHER EDUCATION INSTITUTIONS. HOW TO BEGIN?
PublicationThe objective of this article is to present an outline of a concept aimed at identifying the possibilities of using Lean Management foundations in determining the sources of irregularities occurring in university processes from the perspective of various stakeholder groups. A research methodology is presented that creates the basis for initiating programmes modernising university processes in line with the principles of the LM...
-
Przekształtnik prądu jako sterownik w układach napędowych z silnikami indukcyjnymi
PublicationThe circuits used for power conversion applied in drives with electric machines are classified into two groups: voltage source inverters (VSI) and current source inverters (CSI). Application of the current source inverter results in better properties of drive than application of voltage source inverter because there is no output filter. The development of power electronics and especially the IGBTs, in which on/off-times are very...