Search results for: PROPELLER SHAFT BEARINGS
-
Influence of surface roughness topography on properties of water lubricated polymer bearings, experimental research
PublicationW artykule przedstawiono wyniki badań eksperymentalnych, których celem było zidentyfikowanie wpływu ułożenia chropowatości na powierzchni ślizgowej łożyska smarowanego wodą z polimerową panwią. Badania wykazały, że wpływ ten jest mniejszy niż oczekiwano a na własności łożyska ma wpływ głównie wysokość chropowatości.
-
Influence of local bush wear on properties of water lubricated marine stern tube bearings
PublicationW artykule przedstawiono propozycję metody obliczania łożysk ślizgowych smarowanych cieczą o niskiej lepkości (wodą) w których doszło do lokalnego zużycia panwi. Proponowana metoda uwzględnia sprężystą deformację panwi (model EHL) oraz zmianę geometrii będącą wynikiem zużycia.
-
Comparative analysis of the theoretical models of ideal propulsor, ideal fluid brake, ideal screw propeller and ideal axial wind turbine
PublicationThe article presents a detailed discussion of four different fluid dynamics devices.These devices are presented with all relevant mathematical formulae regarding the forces, the power and the efficiency. It is demonstrated that application of the Betz theorem to axial wind turbines is not correct and it underestimates the maximujm achievable efficiency. This conclusion is supported by numerical calculations.
-
Fatigue resistance investigation of the IC engine MB11 bearings, working under conditions of dynamic unidirectional loadings
PublicationThe slide bearing material MB11 fatigue resistance has been investigated with the application of SMOK - test stand in which dynamic unidirectional loadings to the test bearing is generated. Slide bearing layer consists of the bronze MB11 ( Cu Pb22 Sn 3 ) sintered to the steel shell. Each of the tested bearing has been subject to the standard 20-hour test, under conditions of the full fluid lubrication. Methodology of the experiments,...
-
On the effectiveness of Ni alloy-bronze composite lattice structures used in slide bearings operated under heavy loads
Publication -
The effect of the exposure-in-oil on the contact of the polymers forming sliding layers in hydrodynamic bearings. Wpływ ekspozycji w oleju na kąt zwilżania polimerów stosowanych na warstwy ślizgowe w łożyskach hydrodynamicznych.
PublicationPolimery stosowane jako warstwy ślizgowe w hydrodynamicznych łożyskach wzdłużnych to zazwyczaj tworzywa termoplastyczne charakteryzujące się relatywnie wysokimi wartościami kątów zwilżania w porównaniu z metalami. Metale, w tym również Babbitt czy inne stopy łożyskowe, cechują niskie wartości kątów zwilżania. Im niższy kąt, tym powierzchnia lepiej się zwilża. Tworzywa sztuczne wykorzystywane w węzłach tribologicznych mających zapewnić...
-
STUDY IN MECHANICAL FAULT ELEMENT THERMOGRAPHY THROUGH THE MACHINE: The case of deep groove ball bearings of a career without screen.
Publication -
EXPERIMENTAL STUDY OF DIFFERENT SUPPLY DESIGNS IN HYDRODYNAMIC THRUST BEARINGS = Badania doświadczalne różnych sposobów smarowania wzdłużnych łożysk ślizgowych
PublicationHydrodynamiczne łożyska wzdłużne charakteryzują się znacznymi stratami tarcia, które przyczyniają się do wzrostu temperatury łożyska i obniżenia jego nośności. Obecnie olej smarujący jest zazwyczaj chłodzony w zewnętrznych układach chłodzenia. Po schłodzeniu olej jest dostarczany z powrotem do korpusu łożyska, z reguły do przestrzeni między klockami łożyska. Skuteczność dostarczania schłodzonego oleju w pobliże wlotu do szczeliny...
-
Powłoki fluoropolimerowe oraz przeciwzatarciowe w łożyskach foliowych smarowanych wodą = Fluoropolymer and anti-friction coatings for water-lubricated foil bearings
PublicationW artykule przedstawiono krótką charakterystykę oraz wyniki badań tribologicznych wybranych powłok fluoropolimerowych oraz przeciwzatarciowych. Badania zużycia powłok przeprowadzono pod kątem zastosowania w oryginalnym łożysku foliowym smarowanym wodą. Na podstawie analizy wyników wyłoniono trzy powłoki do potencjalnego zastosowania w łożyskach foliowych smarowanych wodą.
-
Analiza przepływu oleju przez rowek smarowy wzdłużnego łożyska ślizgowego = Analysis of the lubricant flow through the hydrodynamic thrust bearings groove
PublicationSmarowanie zanurzeniowe jest tradycyjnym sposobem smarowania wzdłużnych łożysk ślizgowych. Jednak rozwiązanie to wykazuje umiarkowaną skuteczność w zapewnieniu optymalnie niskich temperatur w filmie smarowym a ponadto jest przyczyną strat mocy związanych z mieszaniem oleju w obudowie łożyska, co jest szczególnie widoczne w łożyskach szybkoobrotowych. Wymagania stawiane nowym konstrukcjom łożysk ślizgowych to zwiększanie nośności...
-
Wykorzystanie modelu silnika indukcyjnego klatkowego do prądowej diagnostyki jego łożysk. Application of induction machine model for current diagnostics of bearings
PublicationW pracy podano widmo prądu stojana dla silnika normalnego oraz wprawianego w drgania o nastawianej częstotliwości. Drgania korpusu wirnika skutkują uginaniem się wirnika, co symuluje bicie wirnika od uszkodzenia łożysk. Podano też model matematyczny silnika, dopuszczający niecentryczność wirnika. Podano widmo prądu stojana przy pracy z wibracjami wirnika odwzorowującymi w pewnym przybliżeniu wibracje od uszkodzonych łożysk.
-
Wpływ założeń modelu obliczeniowego na wyniki obliczeń hydrodynamicznych łożysk wzdłużnych = The influence of model simplifications on the predicted performance of hydrodynamic thrust bearings
PublicationPrzedstawiono porównanie wyników obliczeń hydrodynamicznych łożysk wzdłużnych otrzymanych z wykorzystaniem dwóch niezależnie opracowanych modeli obliczeniowych TEHD (termoelastohydrodynamicznych). Wykorzystane w obliczeniach programy różnią się głównie założeniami i uproszczeniami przyjętymi, zwłaszcza w odniesieniu do części przepływowej zadania. Symulacje obliczeniowe przeprowadzono stosując w przypadku obu modeli te same warunki...
-
Obliczeniowa analiza wybranych systemów dostarczania smaru w hydrodynamicznych łożyskach wzdłużnych = Computational analysis of selected supply designs in hydrodynamic thrust bearings
PublicationPrzedstawiono przykładowe wyniki obliczeniowej analizy wpływu zastosowania wybranych systemów dostarczania schłodzonego oleju do łożyska na właściwości łożyska.
-
Results of experimental research of hydraulic satellite motor
Open Research DataThe study of the flow rate in the motor and the torque on the motor shaft at low constant speed were carried out.The file contains measurement data of the torque on the motor shaft and the flow rate in the motor as a function of the angle of shaft rotation at various constant pressure drops in the motor.
-
Pre-swirl energy saving device in marine application
PublicationThis paper covers topics of energy saving device (ESD) with application to marine propulsors. The form of ESD, considered in this paper, consists of fixed lifting foils mounted in front of the screw propeller (the pre-swirl stator/guide vanes). An algorithm for designing propulsion systems, consisting of guide vanes and screw propeller, is presented. The proposed method relies on hybrid lifting line (guide vanes)-lifting surface...
-
Marek Chodnicki dr inż.
People -
Numerical Studies on Propellers in Open Water and behind Hulls aiming to support the Evaluation of Propulsion Tests
PublicationA RANS based numerical analysis of propellers can contribute considerably to our understanding of propeller/hull interaction. It may also allow for a review of scaling procedures on results from experimental fluid dynamics (EFD). Using various RANS codes (Fluent, CFX, STAR-CCM+ and FreSCo+) on common test cases the authors first focused on propeller open water (POW) calculations. Next we simulated the propeller hull interaction...
-
Analiza przepływu oleju przez rowek smarowy wzdłużnego łożyska ślizgowego z wykorzystaniem komputerowej dynamiki płynów (CFD) = Analysis of the lubricant flow through the hydrodynamic thrust bearings groove with the use of computational fluid dynamic
PublicationSmarowanie zanurzeniowe jest tradycyjnym sposobem smarowania wzdłużnych łożysk ślizgowych. Jednak rozwiązanie to wykazuje umiarkowaną skuteczność w zapewnieniu optymalnie niskich temperatur w filmie smarowym a ponadto jest przyczyną strat mocy związanych z mieszaniem oleju w obudowie łożyska, co jest szczególnie widoczne w łożyskach szybkoobrotowych. Obecnie wymagania stawiane nowym konstrukcjom łożysk ślizgowych to zwiększanie...
-
Application of the Optimization Methods to the Search of Marine Propulsion Shafting Global Equilibrium in Running Condition
PublicationFull film hydrodynamic lubrication of marine propulsion shafting journal bearings in running condition is discussed. Considerable computational difficulties in non-linear determining the quasi-static equilibrium of the shafting are highlighted. The approach using two optimization methods (the particle swarm method and the interior point method) in combination with the specially developed relaxation technique is proposed to overcome...
-
Motor bearing diagnostics performed by means of laser vibrometer
PublicationDamage of bearings is the most common cause of failures in squirrel-cage induction motors. That is why the issues connected with diagnostics of bearings are so important. The equipment employed for bearing diagnostics usually makes use of vibrations as the criterion for technical condition of the bearings. This paper presents exemplary results of the research conducted on bearings with artificially introduced damage. A scanning...
-
Tadeusz Stolarski prof. dr hab. inż.
People -
Determination of probabilities defining safety of a sea-going ship during performance of a transportation task in stormy weather conditions
PublicationThe paper presents the possibility of applying the theory of semi-Markov processes to determine the limiting distribution for the process of changes of technical states being reliability states of the systems of sea-going ships significantly affecting safety of such ships, which include main engine, propeller and steering gear. The distribution concerns the probabilities of occurrence of the said states defined for a long time...
-
Torsional elasticity and energetics of F1-ATPase
PublicationFoF1-ATPase is a rotary motor protein synthesizing ATP from ADP driven by a cross-membrane proton gradient. The proton flow through the membrane-embedded Fo generates the rotary torque that drives the rotation of the asymmetric shaft of F1. Mechanical energy of the rotating shaft is used by the F1 catalytic subunit to synthesize ATP. It was suggested that elastic power transmission with transient storage of energy in some compliant...
-
The voltage on bus bars of the main switchboard of the ro-ro ship electrical power system during a sea voyage
Open Research DataThe dataset is part of the research results on the quality of supply voltage on bus bars of the main switchboard of the ship's electrical power system in different states of ship exploitation. The attached dataset contains the measurement results carried out onboard a ro-ro ship during a sea voyage.
-
HYDROSTATIC THRUST BEARING WITH REDUCED POWER LOSSES
PublicationIn many cases in rotating machinery, axial load is carried by tilting pad thrust bearings which have been developed since the beginning of 20th century. For high reliability and simplicity, most commonly the bearings are bath lubricated. In the times of sustainable development, however, minimization of friction losses becomes an important criterion for machinery assessment, and a strategic goal of their development. Performed calculations,...
-
Numerical investigations of the engine cooling system in a small power vesel pod propulsion system
PublicationThe development of electronics and electrotechnology enabled to put electric motors of the alternating current in the pod and to use them for the main drive of ships. A lot of heat which must be picked up from the system is a problem which is turning up at applying the system of this type. Many big ships lately contended with these problems. Building the small propeller for the boat powered with solar power we decided to check...
-
Experimental Research on Insufficient Water Lubrication of Marine Stern Tube Journal Bearing with Elastic Polymer Bush
PublicationWater-lubricated bearings with polymer bushes are steadily gaining popularity due to their advantages, including environmental friendliness, relatively simple construction and long-term operation. Nevertheless, in practice instances of damage to such bearings occur due to insufficient or absent flow of the lubricating agent. In this study, experimental tests established that elastic polymer bush bearing is capable of operating...
-
Tilting pad thrust bearing with novel material selection - experimental comparison of low and medium speed operation
PublicationThe advances in material engineering led to the development of hard carbon based coatings applied in numerous applications in order to prevent or minimize wear of the parts in contact. With Triondur® coatings, the bearing company Schaeffler has succeeded in halving the friction losses in the valve trains of passenger cars. The coatings are optimized for high abrasive wear protection and low sliding friction moments. Altogether...
-
Ecological bearing systems for water turbines – research and development at Gdansk University of Technology
PublicationIncreasing requirements for environmental protection make it necessary to introduce new materials and designs. Hydroelectric power plants operating in direct contact with water reservoirs and rivers are potentially endangering water cleanliness, hence they should also be modernized in the way minimizing the environmental hazards. A lot of progress in this field has been achieved in last decades, but still there is much work to...
-
Intelligent microbearing project with memory of stress-strain history
PublicationTaking into account the increasing need of intelligent micro-bearing with memory, this paper presents the optimization, simulation and practical application of operating parameters(load carrying capacity, friction forces, friction coefficient, wear), simulation for hydrodynamic HDD micro-bearing with curvilinear nano-grooved journal profile. One of the reason of such journal profile is that this journal profile contributes to the...
-
Mathemathical model of radial passive magnetic bearing
PublicationIn the article mathematical radial model of passive magnetic bearings to ocean engineering units has been presented. The units application in underwater thrusters should increase propulsion systems durability and gives lower maintenance costs. The rotor of electric motor is hanging in magnetic field taken from radial passive magnetic bearings. However axial direction maintenance must be controlled with electromagnets and their...
-
Numerical study on seismic response of a base-isolated building modelled with shell elements
PublicationSeismic isolation is counted among the most popular and effective means of protecting structures against earthquake forces. Base isolators, like Lead-Rubber Bearings (LRB), High-Damping Rubber Bearings (HDB) or Friction Pendulum Systems (FPS) are extensively used in practice in many earthquake-prone regions of the world. The present paper reports the results obtained from the numerical study on seismic response of a base-isolated...
-
Analiza możliwości zastosowania środowiska SCILAB do wspomagania projektowania podsystemów energetycznych statków = Analysis of capability of using SCILAB for adding design of power ship subsystems
PublicationW artykule przedstawiono koncepcję wykorzystania środowiska symulacyjnego Scilab, modeli matematycznych oraz badań symulacyjnych przy projektowaniu podsystemów energetycznych statku. Zredagowano przykładową strukturę zawierającą model wysokoprężnego silnika oraz model śruby okrętowej. Przedstawione procedury oraz modele matematyczne zostaną włączone do systemu ekspertowego wspomagającego projektowanie statków. This paper deals...
-
Comparison of induction motor bearing diagnostic test results through vibration and stator current measurement
PublicationThe paper discusses results of tests performed by authors, related to the angine bearings diagnostic using vibration and stator current measurements. The paper contains the description of an automatic measurement system, developed for measurement of those harmonics and processing that to obtain bearing diagnostic information. System was tested on objects with intentionally made defects in bearings, results of this test was also...
-
Manoeuvring forces on azimuthing podded propulsor model
PublicationThis paper presents the preliminary part of comprehensive manoeuvring open- water tests of a gas carrier model. The paper focuses on open water experiments with an azimuthing podded propulsor. The test program was carried out in the cavitation tunnel and the large towing tank of Ship Hydromechanics Division, Ship Design and Research Centre, Gdańsk. The pod was tested as a pushing unit with a 161.3 mm diameter propeller. Steering...
-
The voltage on bus bars of the main switchboard of the ro-ro ship electrical power system during maneuvering
Open Research DataThe dataset is part of the research results on the quality of supply voltage on bus bars of the main switchboard of the ship's electrical power system in different states of ship exploitation. The attached dataset contains the measurement results carried out onboard a ro-ro ship during maneuvering.
-
Wielkogabarytowe hydrodynamiczne łożyska wzdłużne
PublicationW monografii przedstawiono problemy konstrukcyjne i badawcze hydrodynamicznych łożysk wzdłużnych o dużych średnicach. Łożyska takie stanowią istotne i niezwykle odpowiedzialne podzespoły hydrogeneratorów elektrowni wodnych. Z uwagi na rozmiary (średnice przekraczają niekiedy 5 metrów) i złożoność zjawisk łożyska te wymagają specjalnej postaci konstrukcyjnej, a ich dokładna analiza obliczeniowa przysparza wiele problemów. Dodatkowo...
-
Simulation of ship turning circle test for ballast and full load conditions
Open Research DataThe data show the results of the turning circle spiral test for the simplified ship model, taking into account two states of loading: ballast and full load. During the circulation test, the manoeuvrability of the vessel is tested.
-
Model and laboratory simulation of a induction motor for diagnostic purposes
PublicationStatistics say that bearings are this part of induction motors which is most susceptible to damage. The equipment employed for bearing diagnostics usually makes use of vibrations as the criterion for technical condition of the bearings. A faulty bearing results in additional motor vibrations. They are reflected in the harmonic content of stator currents. In certain operating conditions the current signal is the sole source of information...
-
Influence of water and mineral oil on the leaks in satellite motor commutation unit clearances
PublicationThe article describes the flow rates of mineral oil and water flowing, as working media, through the commutation unit of a hydraulic satellite motor. It is demonstrated that geometrical dimensions of commutation unit clearances change as a function of the machine shaft rotation angle. Methods for measuring the rate of this flow and the pressure in the working chamber are presented. The results of pressure measurements in the working...
-
Evaluation of expanded uncertainty of instantaneous power measurement in a bearing diagnostic system.
PublicationThe paper presents the issues concerning the estimation of the expanded uncertainty in the system for the diagnosis of rolling bearings, consisting of transducers: voltage and current voltage, which is used for diagnostic bearing motors method based on the measurement and analysis of the instantaneous power signal consumed by the induction motor. It presents the methodology for assessing the measurement uncertainty and presents...
-
On the Possibility of Increasing Ship Energy Efficiency Through Improved Propulsion Control System
PublicationThis paper summarizes the analyses conducted to assess the impact of the ship's propulsion control system on energy efficiency in calm, manoeuvre, and sea wave conditions, where the goal of the investigation is to develop new strategies for controlling the ship's motion while considering the interactions between the hull, engine, and propeller.
-
Induction machine model for current diagnostics of bearings. W: [CD-ROM]Proceedings and our Portrait. 48 Internationales Wissenschaftliches Kollo- quium. Ilmenau, 22.-25.09.2003. Ilmenau: Tech. Univ. Ilmenau**2003 s. [1-9] 8 rys. Model maszyny indukcyjnej dla prądowej diagnostyki łożysk.
PublicationPojawienie się określonych typów uszkodzeń w silniku jest źródłem odkształ-cenia tego prądu. Poddając przebieg prądu analizie widmowej obserwuje sięszereg składowych, które związane są z określonymi typami uszkodzeń. Referatprezentuje rezultaty badań modelowych i eksperymentalnych. Badania przepro-wadzono na silniku 1,1 kW czterobiegunowym. Zaprezentowany model pozwala za-równo na wprowadzanie wibracji wirnika jak ekscentryczności...
-
The initial selection of parameters for dynamic brake for car engine test dynamometer
PublicationThe article presents an analysis of the car engine loads. The aim of the analysis was to determine the parameters of the brake / electric motor on an engine test bad. Analysis of loads on the driving tests concerned on chassis dynamo to simulate them on an engine dynamometer. To check the range of dynamometer shaft angular acceleration inertial mass of a car was reduced on the crankshaft axis. The calculations of maximum shaft...
-
EMISJA AKUSTYCZNA JAKO SYGNAŁ DIAGNOSTYCZNY ODWZOROWUJĄCY ZMĘCZENIOWE ZUŻYCIE WARSTW ŚLIZGOWYCH PANWI ŁOŻYSK GŁÓWNYCH I KORBOWYCH SILNIKÓW O ZAPŁONIE SAMOCZYNNYM
PublicationW artykule przedstawiono wyniki badań laboratoryjnych, z których wynika, że emisja akustyczna (EA) może być uznana za sygnał diagnostyczny, przydatny do identyfikacji stanu technicznego łożysk głównych i korbowych okrętowych silników o zapłonie samoczynnym. Wykazano w nim bowiem, że parametry emisji akustycznej takie jak: czas rejestracji, energia sygnału, amplituda sygnału, ilość przekroczeń poziomu dyskryminacji, czas narastania,...
-
Microwave Ring Resonator Based Pressure Sensor
PublicationThis paper demonstrates a microwave pressure sensor, which is based on microstrip line-fed ring resonators. The first ring resonator is loaded with the concentric cylindrical shafts, while the same number of the hollow shanks as the shafts are mounted on the second ring resonator. The arrangement of the cylindrical shaft and hollow shank allows for mechanical movement between two substrates while maintaining electrical contact....
-
Use of Neural Networks in Diagnostics of Rolling-Element Bearing of the Induction Motor
PublicationBearing defect is statistically the most frequent cause of an induction motor fault. The research described in the paper utilized the phenomenon of the current change in the induction motor with bearing defect. Methods based on the analysis of the supplying current are particularly useful when it is impossible to install diagnostic devices directly on the motor. The presented method of rolling-element bearing diagnostics used indirect...
-
Influence of an applied bearing system on behaviour of multi-span footbridge
PublicationThe cycle overpass in Gdynia is a box structure over 300 metres long, 10-span. It was opened for bicycle traffic in the second half of 2013. At the end of its construction, there was failure due to excessive horizontal displacement of the system. A number of bearings exceeded the range of permissible transverse shifts thus it was necessary to temporarily protect the spans from slipping. The FEM analysis of the original solution...
-
Acoustic journal bearing - A search for adequate configuration
PublicationClassical non-contact bearings are already used in a number of specialist applications but there are somespecialist areas where they cannot be used for variety of reasons and acoustic sliding bearings could be an alternative. The paper presents the quest for a configuration of an acoustic journal bearing and shows that the overall shape of the bearing and its geometry are of a vital importance for the load capacity oft he bearing....
-
Finite-element analysis of a base-isolated multi-storey steel building under seismic motions
PublicationNumerical simulation of the seismic behaviour of a multi-storey steel building, both fixed-base and base-isolated, under the 1940 El Centro earthquake was performed in this paper. The analyzed 4-storey building was decoupled from the shaking ground with the Polymeric Bearings, which can be considered a proposal of a new seismic isolation system. It consists of rectangular-shaped blocks made of a specially prepared flexible polymeric...
-
PHYSICAL MODEL OF ENERGY-RELATED PROCESSES IN A ROTATING MECHANICAL SYSTEM FOR THE PURPOSES OF DIAGNOSIS OF TRANSMISSION SHAFTS
PublicationIn the present article, selected problems connected with identification of slowly changing energy-related processes accompanying high cyclic fatigue of construction materials of simple mechanical systems, with special consideration of transmission shafts, are mentioned for diagnostic purposes. The article also presents physical models of object and processes that in a simplified way reflect mechanical energy transmission from transmission...
-
Prospects of Decreasing Power Losses in a Hydrostatic Thrust Bearing
PublicationIn numerous machines, axial load is carried by tilting pad thrust bearings known since the beginning of 20th century. These bearings are commonly bath lubricated, which is simple, does not require any additional pumps, and, due to this, such systems are highly reliable. In a contemporary technology, however, minimization of friction losses became an important goal of machinery improvement. Calculations based on elementary rules...
-
Investigating Fuel Injection Strategies to Enhance Ship Energy Efficiency in Wave Conditions
PublicationThe prediction of fuel consumption and resulting transportation costs is a crucial stage in ship design, particularly for conditions involving motion in waves. This study investigates the real-time fuel consumption of a container ship when sailing in waves. The overall ship performance is evaluated using a novel non-linear coupled hull-engine-propeller interaction model. A series of towing tank experiments for hull resistance in...
-
Wybrane metody diagnostyki łożysk silników indukcyjnych oparte o pomiar prądu
PublicationW artykule zawarto przegląd wybranych metod diagnostyki łożysk silnika indukcyjnego, bazujących na pomiarach prądu zasilającego. Jedno z nowych rozwiązań przetwarzania sygnałów zostało zaadaptowane przez autorów do stosowanego przez nich systemu diagnostycznego. Wyniki wstępnych badań symulacyjnych zweryfikowanych badaniami na rzeczywistym obiekcie wskazują, że rozwiązanie to ułatwia diagnozowanie. Autorzy zamierzają prowadzić...
-
Mohammad Hossein Ghaemi dr inż.
PeopleMohammad Hossein Ghaemi Mohammad Hossein Ghaemi (1967), is an Assistant Professor at the Faculty of Mechanical Engineering and Ship Technology - WIMiO (till 2020: Faculty of Ocean Engineering and Ship Technology), Department of Automatics and Marine Energy Engineering. He studied first at Tehran University, where was graduated in the field of Mechanical Engineering (Solid Mechanics). Then he received his MSc degree in the area...
-
EXPERIMENTAL EVALUATION OF DLC/STEEL SLIDING CONTACTS’ OPERATIONAL ENVELOPE
PublicationIn an industrial project concerning sliding bearings, a sliding pair was selected of high alloy steel vs. industrial grade DLC coated high alloy steel as a basis for an innovative design of high performance sliding bearings lubricated with a synthetic oil for use in geared transmission units. The development process required credible data on the ultimate resistance of the sliding pair to very high contact stress. An experimental...
-
Identification of residual force in static load tests on instrumented screw displacement piles
PublicationOccurrence of the so-called residual force of an unknown value significantly disturbs interpretation of static load tests performed on piles equipped with additional measuring instruments. Screw displacement piles are the piling technology in which the residual force phenomenon is very common. Its formation mechanism is closely related to the installation method of this type of piles, which initiates generation of negative pile...
-
Influence of operating pressure on the durability of a satellite hydraulic motor supplied by rapeseed oil
PublicationThis article describes the results of a durability test of a hydraulic satellite motor supplied by rapeseed oil. The tests were carried out on a test stand in a power recuperation system. The tests of the motor were carried out at a constant shaft speed for three fixed pressure drops in the motor. This made it possible to demonstrate the influence of the motor operating pressure on the durability of the satellite mechanism. The...
-
Effect of manufacturing errors of the pad sliding surface on the performance of the hydrodynamic thrust bearing
PublicationIn the present study, investigation of the effect of manufacturing errors on the performance of large tilting pad thrust bearings has been performed, following a CFD-based Thermohydrodynamic analysis of a single pad. A 3D model has been generated, including the pad, the lubricant film and the corresponding part of the collar. The pad has been assumed to be deformed about the pivot point, due to thrust loading. Manufacturing errors...
-
Mathematical Modelling of a Seismic Isolation System to Protect Structures During Damaging Earthquakes
PublicationThe present study aims to determine the effectiveness of a nonlinear mathematical model in simulating complex mechanical behaviour of a seismic isolation system to protect structures during strong and damaging earthquakes. In order to construct the Polymeric Bearings considered in this research, a specially prepared flexible polyurethane elastomer with increased damping properties has been used. The usefulness of the proposed mathematical...
-
Comparison of selected parametric methods for prediction of inland waterways ship hull resistance in towing tank test
PublicationIn the paper selected approximate methods for calculation of inland waterways ship resistance and their verification by towing tests, compared on the example of a small urban ferry, are presented. The test results are made for both the bare hull and the hull with appendages (skeg, azimuthal propeller). Significant differences between results of the theoretical methods and experimental ones, especially in the case of the model with...
-
The basics of design and experimental tests of the commutation unit of a hydraulic satellite motor
Publicationhe article presents an analytical method to design the commutation unit in a hydraulic satellite motor. It is shown that the size of the holes feeding the working chambers and their location on the plates closing those chambers depends on the geometrical dimensions of the working mechanism. The overlap in the commutation unit depends on the rotational speed range. It is demonstrated that the geometrical dimensions of the commutation...
-
UKŁAD PRZENIESIENIA NAPĘDU TURBINY WIATROWEJ
PublicationIn a most commonly met design of a wind turbine the power is transmitted from the rotor to the generator through the system composed of the main shaft, friction connection, multiplicating gearbox and a flexible coupling. The driving system comprises almost a complete set of the machine elements being described during machine design lectures and can serve as an interesting illustration of the lectures.
-
Drivetrain of a Wind Turbine
PublicationIn a most commonly met design of a wind turbine the power is transmitted from the rotor to the generator through the system composed of the main shaft, friction connection, multiplying gearbox and a flexible coupling. The driving system comprises almost a complete set of the machine elements being described during machine design lectures and can serve as an interesting illustration...
-
Ecology In Tribology: Selected Problems of Eliminating Natural Oil-Based Lubricants from Machine Friction Couples
PublicationThe elimination of mineral oil-based lubricants from machines has multiple beneficial effects on the natural environment. Firstly – these lubricants are a direct threat to the environment in the event of leaks; secondly – their elimination reduces the demand for crude oil from which they are obtained. In addition, in many cases, e.g. when replacing traditional lubricants with water, friction losses in the bearings can also be reduced...
-
DIAGNOSTYKA ŁOŻYSK SILNIKA INDUKCYJNEGO PRZY UŻYCIU POMIARU PRĄDU ZASILAJĄCEGO I WIBRACJI
PublicationW artykule przedstawione zostały wyniki badań diagnostycznych łożysk silnika indukcyjnego z zastosowaniem metody pomiaru prądu zasilającego oraz wibracji. Poruszone zostały problemy dotyczące poszukiwania nowej metody opartej na pomiarze i analizie prądu, która w znacznym stopniu ułatwiłaby szybkie i sprawne znalezienie uszkodzenia w maszynie, bez konieczności bezpośredniego dostępu do badanego urządzenia. Zaprezentowano rezultaty...
-
Simulation of ship spiral test for ballast and full load conditions
Open Research DataThe data show the results of the spiral test for the simplified ship model, taking into account two states of loading: ballast and full load. The data set contains the results of time simulation for sea state 10 on the Beaufort scale: changes in rudder angle delta_tab[deg]; angular velocity r_tab[deg/s]; surge velocity u_tab (m/s); sway velocity v_tab...
-
Equivalent standard manoeuvres for pod-driven ships
PublicationProcedures for carrying out the manoeuvring tests presented in International Maritime Organisation (IMO) resolution MSC.137(76) are based on the capabilities of ships with conventional steering-propulsion systems. Therefore they do not correspond to ships with other steering-propulsion devices, like pod drives. IMO is aware of this shortcoming and for ships with non-conventional steering and propulsion system may permit the use...
-
High load capacity spur gears with conchoidal path of contact
PublicationThe present study is devoted to investigation of spur gears with a conchoidal path of contact and a convex-convex contact between teeth. The load capacity and energy efficiency were evaluated using both theoretical and experimental approaches. The theoretical analysis showed that the conchoidal gear pairs are 5–21% stronger in terms of contact stress and have similar energy efficiency as compared to the involute gear pairs of the...
-
Instrument detection and pose estimation with rigid part mixtures model in video-assisted surgeries
PublicationLocalizing instrument parts in video-assisted surgeries is an attractive and open computer vision problem. A working algorithm would immediately find applications in computer-aided interventions in the operating theater. Knowing the location of tool parts could help virtually augment visual faculty of surgeons, assess skills of novice surgeons, and increase autonomy of surgical robots. A surgical tool varies in appearance due to...
-
Modelling of Geared Multi-Rotor System
PublicationIn the paper the method of modelling a speed-varying geared rotor system is presented. The proposed approach enables us to obtain an accurate low-order lumped parameter representation of the investigated system. The final model consists of reduced modal models of an undamped beam/torsional shaft system as well as a spatially lumped model of other linear and nonlinear phenomena including gear mesh interaction.
-
Compact satellite hydraulic unit
PublicationThe article describes the design and operation of a prototype hydraulic unit. It is based on an inversed kinematics, satellite pump in which the body rotates around the shaft. The pump is placed inside the electric motor. Thanks to that the compact and low mass construction was achieved. Thanks to new commutation unit with enlarged channels, lower pressure losses were obtained. The article presents the construction and results...
-
Effect of Coating Material Properties on Tilting-pad Thrust Bearing Performance
PublicationPolymer lined tilting-pad bearings demonstrate many advantages over traditional bearing systems. Bearings with a polymer layer in comparison with a babbitted layer show, for example: lower value of friction coefficient (important during start/stops), higher fatigue strength of the coating, better distribution of the load on individual pads due to lower elasticity of the polymers, wider range of operational temperatures or the ability...
-
NEW DESIGNS OF MAGNETIC FLUID SEALS FOR RECIPROCATING MOTION
PublicationT he operating conditions of magnetic fluid seals during reciprocating motion are so different from those observed in rotating motion that the use of their conventional structures for reciprocating motion seals yields no good results. The analysis of the sealing mechanism of magnetic fluid seals in reciprocating motion shows that the operation of these seals is affected by the carry-over phenomenon and magnetic fluid...
-
Static Load Test on Instrumented Pile – Field Data and Numerical Simulations
PublicationFor some time (since 8-10 years in Poland) a special static load tests on instrumented piles are carried out. Such studies are usually of a scientific nature and provide detailed quantitative data on the load transfer into the ground and characteristics of particular soil layers interaction with a pile shaft and pile base. Deep knowledge about the pile-subsoil interaction can be applied for a various design purposes, e.g. numerical...
-
Static load test on concrete pile – instrumentation and results interpretation
PublicationFor some time (since 8-10 years in Poland) a special static load tests on instrumented piles are carried out. Such studies are usually of a scientific nature and provide detailed quantitative data on the load transfer into the ground and characteristics of particular soil layers interaction with a pile shaft and pile base. Deep knowledge about the pile-subsoil interaction can be applied for a various design purposes, e.g. numerical...
-
Analysis and assessment of the acoustic emission suitability for determination of the energy states of a tribological system in the form of a four-ball tester friction node
PublicationThe present operating safety and cost reduction requirements of the compression ignition engines make it necessary to search for new methods of detecting their defects, e.g. by the analysis of acoustic emission signals coming from the slide bearings. The paper presents non-destructive measurements of acoustic emission (AE) in order to obtain information on the processes taking place in a tribological system under the continuously...
-
Study of the Influence of Heat Convection Coefficient on Predicted Performance of a Large Tilting-Pad Thrust Bearing
PublicationPart of the heat generated by the shearing of the lubricating film during operation of a hydrodynamic bearing is transferred to the bearing components. In the case of the pad, which is usually fully submerged in the lubricating oil, heat is further transferred at the pad free walls to the oil by convection. This mechanism causes a thermal gradient in a pad and, consequently, its thermal deflection. In large hydrodynamic thrust...
-
Diagnostic Model of Crankshaft Seals
PublicationT he paper presents a research stand being a diagnostic model of radial lip seals used, among others, on crankshafts of piston combustion engines in order to identify the correctness of their operation. The possibility of determining the technical condition of lip seals on the basis of the proposed coefficient of correctness of operation has been described. T he basic features of seals influencing their correctness of...
-
The time-varying low-frequency magnetic-field emitted from the ship’s inverter-fed induction motor
Open Research DataThe dataset contains the magnetic field measurement results that are part of a comprehensive study on the assessment of the magnetic field emissions onboard of the research-training vessel. The measurements were carried out, nearby the bow thruster motor fed from the inverter, during maneuvering and the sea voyage. The bow thruster is assembled in the...
-
Compliance tests of the polymer layers used as hydrodynamic bearing coatings
PublicationOperational experience and scientific investigations results showed that polymer lined hydrodynamic bearings can withstand more severe operating conditions compared than white metal bearings. PTFE and PEEK-based coatings are the most frequently used as Babbitt alternatives. Both polymers differ significantly from the each other in material properties. According to catalogue data compression modulus of PTFE, it is about an order...
-
Retrievable strain measuring system in screw displacement piles - readings and results interpretation problems
PublicationStatic load tests on foundation piles are generally carried out in order to determine load – displacement characteristic of the pile. For more detailed information, e.g. force distribution along the shaft, load transfer mechanism and characteristics of soil-structure interaction (unit resistance curves t-z, q-z) additional pile instrumentation is required. Most popular techniques focus on direct concrete strain measurements and...
-
NEW CONCEPT OF HYBRID PROPULSION WITH HYDROSTATIC GEAR FOR INLAND WATER TRANSPORT
PublicationThe article presents the development of author’s concept of a diesel/hydraulic propulsion system for inland watercraft. Due to specific nature of vessel navigation on rivers, classical propulsion systems with shaft lines can be effectively replaced by systems with hydraulic power transmission. A solution is also presented of a hybrid design with extra electric port having the form of a pumping system driven from a battery of accumulators....
-
Influence of the position of the swash plate rotation axis on the volumetric efficiency of the axial pistons pumps
PublicationThe article describes the influence of the position of the swash plate axis of rotation on the size of the dead space and the volumetric efficiency of the axial pistons pump. Superposition of the two motions have been proposed - the rotation of the swash plate with respect to axis intersecting the axis of rotation of the pump shaft and the shifts of swash plate yielding a result of the rotation axis offset effect. In the article...
-
Wzbudzone siły wewnętrzne : skutki upr0szczonego modelowania zakrzywionej estakady sprężonej
Publicationthe paper presents problems, which were encountered during the construction of a southern road bypass of city gdansk. after prestressing and removing formwork, the contractor spotted, that some of outer bearings are detached. performed analysis showed that, this situation was caused by the usage of a simplified, straight beam model during design phase. the paper shows the influence of a curved in plane prestressed system on internal...
-
The system for remote monitoring of a vertical axis wind farm
PublicationThe article presents a system for remote monitoring of working parameters of a wind turbine with a vertical axis. The monitoring system was built using a Raspberry PI 3 microcomputer with the Raspbian operating system and a MicroDAQ E2000 measuring card. The developed system enables monitoring the power output of the generator, torque on the turbine shaft, turbine speed and wind speed. The values of the monitored parameters are...
-
Metoda diagnostyki łożysk na podstawie analizy przebiegów prądu i napięcia zasilającego silnik indukcyjny.
PublicationW niniejszej monografii przedstawiono oryginalne podejście i realizację diagnostyki łożysk silników indukcyjnych przy użyciu metody opartej na pomiarach i analizie iloczynu wartości chwilowych prądu i napięcia zasilającego maszyny. Uzyskane wyniki badań eksperymentalnych na obiektach rzeczywistych okazały się zbieżne z wynikami badań symulacyjnych i potwierdziły, że powstanie uszkodzeń łożysk w silniku skutkuje pojawieniem się...
-
Uncertainty analysis of measuring system for instantaneous power research
PublicationThe paper presents a metrological analysis of the measurement system used for diagnosis of induction motor bearings, based on the analysis of the instantaneous power. This system was implemented as a set of devices with dedicated software installed on a PC. A number of measurements for uncertainty estimation was carried out. The results of the measurements are presented in the paper. The results of the aforementioned analysis helped...
-
Low-Cost Flight Simulator with Possibility of Modeling of Flight Controls Failures
PublicationThe goal of this paper is to present a development of a low cost flight simulator, that allows to simulate flight controls failures. Cessna 172 has been chosen as an example of a general aviation aircraft and the flight model has been implemented in Simulink. The model allows for easy integration of an experimental autopilot, using various strategies. Aerodynamic coefficients have been calculated using software called DATCOM. Such...
-
Wysokociśnieniowe uszczelnienia ruchu obrotowego wału hydraulicznych maszyn wyporowych
PublicationW artykule przedstawiono wyniki badań mające na celu wytypowanie węzła uszczelniającego wał silnika hydraulicznego zapewniającego najwyższą trwałość przy smarowaniu wodą. Parametry pracy: ciśnienie 2 MPa i minimalna prędkość poślizgu uszczelek 2 m/s. Opisano również nowatorski przyrząd, na którym przeprowadzono pomiary wszystkich parametrów węzła uszczelniającego.
-
HYDROACOUSTIC NOISE MEASUREMENTS
PublicationThe paper deals mainly with investigation of underwater noise that propagation is in shallow water. In this paper has been presented the experimental investigation results concerning the distribution of the sound field pressure generated by moving ships in the shallow water at the small distance from the ship. The main acoustical characteristics describing features of the field are spectrograms in pseudo 3D system – distance and frequency...
-
Parametrical 3D model of an asynchronous motor - AutoCAD application.
PublicationA computer program for automatic drawing of 3D models of squirrel-cage induction motors is presented in this paper. The created model of a machine is of parametrical nature, which means that the user defines geometry of particular elements (shaft, stator core, bearing, windings etc.) on the basis dimensions and some other parameters e.g. type of bearing, kind of winding, number of slots. This program is useful for 3D modelling...
-
Possibility of Fault Detection in Sensorless Electric Drives
PublicationThe work presents a fault detection method for an induction motor drive system with inverter output filter. This approach make use of a load torque state observer, which complete structure is presented along with the used control structure. Moreover, the demonstrated drive system operates without rotor speed measurement in conjunction with the multiscalar control. The verification of the demonstrated idea was performed on an experimental...
-
Large hydrodynamic thrust bearing: Comparison of the calculations and measurements
PublicationHydrodynamic thrust bearings, used to carry axial loads in heavily loaded shafts of water power plants hydro turbines, can reach outer diameters even exceeding 5 m. In such large objects scale effect could be observed. According to this, allowable bearing specific load assuring safe operation of the bearings has to be decreased, which increases thrust bearing dimensions. This effect is caused by excessive thermal deflections of...
-
Dynamic Positioning Capability Assessment for Ship Design Purposes
PublicationThe article focuses on solving a problem of optimal thrust distribution over the actuators in a ship Dynamic Positioning, according to DNV-ST-0111 standard, Level 1. The classic Quadratic Programming approach is combined with the numerical solusion used to handle the propeller with the rudder constraints in the optimization task and the influence between thrusters and skeg. It is presented as an efficient method of minimizing the...
-
Experimental study on the selected aspects of bow thruster generated flow field at ship zero-speed conditions
PublicationThe paper presents the results of experimental study on the interaction between the bow thrusters understood as the flow field changes generated by bow tunnel thruster in deep water conditions operated as a single and twin units. The research was limited to zero-speed case for the ship dead in the water. The influence of the hull form and jet spread between the neighbouring thrusters for several combinations of the applied bow...
-
Diagnostyka łożysk silnika indukcyjnego na podstawie prądu zasilającego przy użyciu sztucznych sieci neuronowych
PublicationW artykule zawarto wyniki badań dotyczące diagnostyki łożysk silnika indukcyjnego na podstawie pomiarów prądu zasilającego z wyko-rzystaniem sztucznych sieci neuronowych. Zaprezentowano wyniki uczenia sieci oraz rezultaty testów przeprowadzonych na danych spoza zbioru uczącego. Badania wykonane zostały na obiektach z celowo wprowadzonymi uszkodzeniami łożysk. Przedstawiona nowa koncepcja zakłada użycie zestawu sieci neuronowych...
-
A Review of Reduction Methods of Impact of Common-Mode Voltage on Electric Drives.
PublicationIn this survey paper, typical solutions that focus on the reduction in negative effects resulting from the common-mode voltage influence in AC motor drive applications are re-examined. The critical effectiveness evaluation of the considered methods is based on experimental results of tests performed in a laboratory setup with an induction machine fed by an inverter. The capacity of a common-mode voltage level reduction and voltage...
-
Search for the most useful geometry of an acoustic journal bearing
PublicationComputer simulations of a number of journal bearing’s geometries utilising acoustic levitation were carried out. The choice of the best geometry depended on the ability of a deformed shape, created by piezo-electric elements, to facilitate squeeze film ultrasonic levitation, and also to create three evenly distributed diverging aerodynamic gaps. Deformations of analysed variants of the bearing’s shape were generated by numerical...
-
Niekorzystny wpływ przekształtnikowego zasilania PWM na silniki asynchroniczne trakcyjne
PublicationThe electric traction drives with an AC motor fed by a frequency converter are used more and more often nowadays. The most significant side effects, of a converter's output voltage forming PWM method for AC motor windings, are steep voltage changes, which can initiate several destructive phenomena. The paper presents the adverse influence of a converter common mode voltage on the motor windings' increased voltage exposure and the...