Filters
total: 899
filtered: 758
Search results for: GEOMETRICAL ARGUMENTS
-
Mountain pass solutions to Euler-Lagrange equations with general anisotropic operator
PublicationUsing the Mountain Pass Theorem we show that the problem \begin{equation*} \begin{cases} \frac{d}{dt}\Lcal_v(t,u(t),\dot u(t))=\Lcal_x(t,u(t),\dot u(t))\quad \text{ for a.e. }t\in[a,b]\\ u(a)=u(b)=0 \end{cases} \end{equation*} has a solution in anisotropic Orlicz-Sobolev space. We consider Lagrangian $\Lcal=F(t,x,v)+V(t,x)+\langle f(t), x\rangle$ with growth conditions determined by anisotropic G-function and some geometric conditions...
-
Uniwersalna metoda projektowania regulacji osi toru z wykorzystaniem pomiarów satelitarnych i optymalizacji
PublicationW pracy zwrócono uwagę na ograniczenia stosowanej w naszym kraju metodyki regulacji osi toru związane w głównym stopniu z uzyskiwaną dokładnością określania istniejącego kształtu toru. Jako rozwiązanie alternatywne wskazano opracowaną przez interdyscyplinarny zespół naukowy Politechniki Gdańskiej i Akademii Marynarki Wojennej / Akademii Morskiej w Gdyni i stosowaną od 2009 roku nowatorską technikę mobilnych pomiarów satelitarnych....
-
KRAJOBRAZOWY WYMIAR RURALISTYKI
PublicationTytuł Krajobrazowy wymiar ruralistyki w pełni oddaje treść pracy. Najogólniej mówiąc, rozprawa relacjonuje poszukiwania sposobów udziału krajobrazu w planowaniu przestrzennym obszarów wiejskich. Książka, wbrew swojemu układowi, nie powstawała według zwyczajowej ścieżki: od tezy, mieszczącej się w dziedzinie architektury i urbanistyki, do argumentów, które wywiedzione z tej dyscypliny, przemówiłyby za nią. Analiza stanu badań wskazywała...
-
Metodyka projektowania i eksploatacji dróg szynowych z wykorzystaniem mobilnych pomiarów satelitarnych
PublicationW pracy zostały przedstawione aplikacyjne możliwości metody mobilnych pomiarów satelitarnych w projektowaniu i eksploatacji dróg szynowych. Pokazano wizualizację położenia toru kolejowego, omówiono sposoby oceny odcinków prostych toru i odcinków położonych w łuku oraz tworzenie poligonu kierunków głównych trasy. Szczególną uwagę poświęcono opracowanej analitycznej metodzie projektowania, omawiając jej algorytmy obliczeniowe: projektowania...
-
Automatic Correction of Non-Anechoic Antenna Measurements using Low-Pass Filters
PublicationPrototype measurements belong to key steps in the development of antenna structures. They are normally performed in expensive facilities, such as anechoic chambers (ACs). Alternatively, antenna performance can be extracted (at a low cost) in non-anechoic conditions upon appropriate post-processing. Unfortunately, existing correction algorithms are difficult to set up and prone to failure, which limits their practical usefulness....
-
Technical fabrics in costruction of large scale roofs - numerical and experimental aspects
PublicationDesigning and construction of textile hanging roofs is the challenging subject for engineers. This type of structure needs geometrically and very often also physically non-linear calculations. Due to different behaviour of two families of threads (warp and weft), which during deformation can change the angle between their directions, they require special constitutive modelling. Also the loading of hanging roofs is very special....
-
RACIAL COMPOSITION OF COMMUNITIES AND PARTICIPATION OF ADOLESCENTS
PublicationThe investigation used the Add Health data set to examine the association between communities’ composition with respect to race and participation in extracurricular school activities in secondary education. Results of this analysis show that the composition of adolescents’ communities matters for individuals’ participation outcomes in extracurricular school activities. The results find further support in previous research connecting...
-
The influence of chemical composition of amide block on the thermal properties and structure of terpoly(ester-b-ether-b-amide) elastomers
PublicationMultiblock terpolymers-(PBT-b-PTMO-b-PA12,10)(n)- constituting the polymer systems, in which one of the three blocks (PBT) does not dissolve in PA12,10 block (hard phase) and, depending on its molecular weight is slightly soluble in PTMO block (soft phase), have been obtained. The DSC method was applied to investigate the thermal properties of these polymers and it was found that PBT block acts as an element that produces stiffness...
-
Testing Stability of Digital Filters Using Multimodal Particle Swarm Optimization with Phase Analysis
PublicationIn this paper, a novel meta-heuristic method for evaluation of digital filter stability is presented. The proposed method is very general because it allows one to evaluate stability of systems whose characteristic equations are not based on polynomials. The method combines an efficient evolutionary algorithm represented by the particle swarm optimization and the phase analysis of a complex function in the characteristic equation....
-
The Third Sector in the Universities’ Third Mission
PublicationThe interactions between the today’s university and its environment, as part of the university’s social responsibility, have been subject to many scientific papers. Their authors typically focus on interdependencies between universities, the state and the market. What is lacking are publications related to the interactions between universities and third sector organisations, and more broadly – a civil society, that may play an...
-
Torsion of restrained thin-walled bars of open constant bisymmetric cross-section
PublicationElastic and geometric stiffness matrices were derived using Castigliano's first theorem, for the case of torsion of restrained thin-walled bars of open constant bisymmetric cross-section. Functions which describe the angles of torsion were adopted from the solutions of thedifferential equation for restrained torsion. The exact solutions were simplified by expanding them in a power series. Numerical examples were taken from Kujawa...
-
Stability of a truss under upward wind loading
PublicationThe present paper is devoted to the numerical investigations of stability of a truss under upward wind load. The truss is braced at its the upper cord. A structural variant including lateral braces, or lateral and torsional braces is considered. The research presents the problems of linear buckling and non-linear static analysis of the truss shell and beam model with geometric and material non-linearity are presented. The initial...
-
Anode supported single chamber solid oxide fuel cell in CH4-Air Mixture.
PublicationW tej pracy przedstawiono wyniki prac ogniw paliwowych na bazie elektrolitu z tlenku cyrkonu stabilizowanego itrem o grubości 1-2um wytworzonego na podłożu cermetu z tlenku niklu i tlenku cyrkonu stabilizowanego itrem. LSCF był wykorzystany jako katoda. Ogniwo paliwowe było testowane w konfiguracji jednokomorowej w mieszaninie powietrza i metanu. Uzyskano napięcie o wartości 0.8V, zaś moc wynosiła 0.12W/cm2. Zbdadano wpływ przepływu...
-
The use of Response Surface Methodology for reliability estimation of composite engineering structures
PublicationStability loss is one of the key issues in the analysis of shells made of composite materials. This paper aims at finding the variation of the critical or limit value of the load resulting from geometric imperfections. An axially compressed 16-layer cylindrical panel model is considered. The imperfections of the panel are simulated as random fields. The parameters of these fields are used as the basic variables of the reliability...
-
Probabilistic estimation of diverse soil condition impact on vertical axis tank deformation
PublicationThe calculations of fuel tanks should take into account the geometric imperfections of the structure as well as the variability of the material parameters of the foundation. The deformation of the tank shell can have a significant impact on the limit state of the structure and its operating conditions. The paper presents a probabilistic analysis of a vertical-axis, floating-roof cylindrical shell of a tank with a capacity of 50000...
-
Notch fatigue analysis and life assessment using an energy field intensity approach in 7050-T6 aluminium alloy under bending-torsion loading
PublicationThis paper studies the fatigue crack initiation and fatigue crack propagation of notched cylindrical bars made of 7050-T6 aluminium alloy subjected to multiaxial bending-torsion loading. The sites of crack initiation and the angles of crack initiation were successfully predicted from the distribution of the first principal stress at the notch surface. Fatigue crack initiation lives were computed through the new concept of energy...
-
A pilot study to assess an in-process inspection method for small diameter holes produced by Direct Metal Laser Sintering
PublicationPurpose The purpose of this research is to evaluate the geometric quality of small diameter holes in parts printed by DMLS technology. An in-process optical inspection method is proposed and assessed during a pilot study. The influence of the theoretical hole diameter assumed in a CAD system and the sample thickness (hole length) on the hole clearance was analysed. Design/methodology/approach The samples made of two different...
-
Buckling of simplified models of silo with corrugated walls and vertical stiffeners
PublicationThe paper deals with buckling of cylindrical silos composed of corrugated sheets and vertical stiffeners (columns). Comprehensive finite element analyses were carried out for a perfect silo by means of a linear buckling approach. Corrugated walls were simulated as an equivalent orthotropic shell and vertical thin-walled columns as beam elements. Calculations for perfect silos with different numbers of columns made it possible to...
-
Numerical analysis of elastic wave propagation in unbounded structures
PublicationThe main objective of this paper is to show the effectiveness and usefulness of the concept of an absorbing layer with increasing damping (ALID) in numerical investigations of elastic wave propagation in unbounded engineering structures. This has been achieved by the authors by a careful investigation of three different types of structures characterised by gradually increasing geometrical and mathematical description complexities....
-
Analysis of the relationship between the length of eye fixation and the parameters of advertisements visible from the road
PublicationIn Poland, many advertising signs addressed to motorists are located along the roadside. Advertisements do not serve any traffic related purpose and can distract drivers making them less reliable and as a consequence, reduce road safety. The existing regulations only apply to the carriageway. The research is conducted as part of the RID project. The objective of the RID project is to create a "Manual for positioning roadside advertising...
-
Reliable Microwave Modeling By Means of Variable-Fidelity Response Features
PublicationIn this work, methodologies for low-cost and reliable microwave modeling are presented using variable-fidelity response features. The two key components of our approach are: (i) a realization of the modeling process at the level of suitably selected feature points of the responses (e.g., S-parameters vs. frequency) of the structure at hand, and (ii) the exploitation of variable-fidelity EM simulation data, also for the response...
-
Experimental and numerical investigation on shell and coil storage unit with biodegradable PCM for modular thermal battery applications
PublicationThermal energy storage (TES) in automotive applications is currently growing in importance. TES can visibly reduce primary energy consumptions, decrease CO2 emission, and improve thermal comfort in electric as well as hybrid vehicles. However, to meet the new ambitious target (15% reduction of CO2 emissions in the new cars until 2025) it is required to use plug-in electric vehicles. For this reason, this paper focuses on the optimization...
-
Current Trends in Wick Structure Construction in Loop Heat Pipes Applications: A Review
PublicationThermal control systems have been introduced as an important part of electronic devices, enabling thermal management of their electronic components. Loop heat pipe (LHP) is a passive two-phase heat transfer device with significant potential for numerous applications, such as aerospace applications, high-power LEDs, and solar central receivers. Its advantages are high heat transfer capability, low thermal resistance, long-distance...
-
An analysis of wind conditions at pedestrian level in the selected types of multi-family housing developments
PublicationThe following article addresses the issue of wind conditions around urban building development at pedestrian level. Factors that depend on those issues include wind comfort and air quality within urbanized spaces. The conditions specific of cities located in a temperate climate zone have been taken into account. The article is intended to identify aerodynamic phenomena characteristic of the three basic types of multi-family building...
-
A New Approach to the PWM Modulation for the Multiphase Matrix Converters Supplying Loads with Open-End Winding.
PublicationThis article presents three variants of the Pulse Width Modulation (PWM) for the Double Square Multiphase type Conventional Matrix Converters (DSM-CMC) supplying loads with the open-end winding. The first variant of PWM offers the ability to obtain zero value of the common-mode voltage at the load's terminals and applies only six switches within the modulation period. The second proposal archives for less Total Harmonic Distortion...
-
Effect of the Cavitation Generation Unit Structure on the Performance of an Advanced Hydrodynamic Cavitation Reactor for Process Intensifications
PublicationThe advanced rotational hydrodynamic cavitation reactors (ARHCRs) that appeared recently have shown obvious advantages compared with conventional devices in process intensifications. In ARHCRs, the cavitation generation unit (CGU) located on the rotor and stator basically determines their performance. For the first time, the present study investigated the effect of the CGU structure on the performance of a representative ARHCR...
-
Dynamic modeling of non-cylindrical curved viscoelastic single-walled carbon nanotubes based on the second gradient theory
PublicationThis paper is devoted to the theoretical study of the dynamic response of non-cylindrical curved viscoelastic single-walled carbon nanotubes (SWCNTs). The curved nanotubes are largely used in many engineering applications, but it is challenging in understanding mechanically the dynamic response of these curved SWCNTs when considering the influences of the material viscosity. The viscoelastic damping effect on the dynamic response...
-
Analityczna metoda projektowania łuków odwrotnych
PublicationW pracy przedstawiono nową metodę projektowania rejonu zmiany kierunku trasy kolejowej, dostosowaną do techniki Mobilnych Pomiarów Satelitarnych. Metoda ta może się okazać szczególnie przydatna wówczas, gdy obydwu prostych kierunków trasy nie można połączyć w sposób elementarny, stosując łuk kołowy z krzywymi przejściowymi; dotyczy to również. zastosowania łuku koszowego. Jedynym rozwiązaniem staje się wówczas wprowadzenie do układu...
-
Wybrane problemy respektowania struktury przyrodniczej w zarządzaniu rozwojem obszarów metropolitalnych
PublicationAutor zadaje pytanie, dlaczego w zarządzaniu rozwojem obszarów metropolitalnych nie zawsze respektuje się ich strukturę przyrodniczą. Analizy pewnych typowych sytuacji pozwalają stawiać hipotezy niektórych tego przyczyn. Należą do nich: ograniczoność przestrzeni i konfliktogenność struktur przestrzennych, mechanizmy społeczno-gospodarcze wymuszające decyzje niekorzystne dla środowiska przyrodniczego, niedostatek świadomości ekologicznej...
-
Modeling SPMD Application Execution Time
PublicationParallel applications in a Single Process Multiple Data paradigm assume splitting huge amounts of data to multiple processors working in parallel at small data packets. As the individual data packets are not independent, the processors must interact with each other to exchange results of the calculations with their adjacent partners and take these results into account in their own computations. An example of SPMD is geometric parallelism...
-
INFLUENCE OF SOLID PARTICLE CONTAMINATION ON THE WEAR PROCESS IN WATER LUBRICATED MARINE STRUT BEARINGS WITH NBR AND PTFE BUSHES
PublicationThis paper reports on a study of the influence of solid particle contamination on the wear process in water-lubricated slide bearings (steel-acrylonitrile-butadiene rubber (NBR) and steel- polytetrafluoroethylene (PTFE)). To compare the wear of the shaft journal and bushes (NBR and PTFE) when lubricated with fresh water and contaminated water, an experiment was carried out to identify key factors that influence the state of wear...
-
Between Descriptive Geometry and CAD 3D
PublicationDescriptive geometry provides methods to analyse three-dimensional space through two-dimensional drawings and prepares to create technical documentation. Geometric form of an engineering project is presented by the means of projection methods based on a 3D model, which is present in designer’s imagination. The forthcoming era of Building Information Modelling (BIM) brings changes in the way the engineer works, as the vision is...
-
Generalization of Kramers-Krönig relations for evaluation of causality in power-law media
PublicationClassical Kramers-Krönig (K–K) relations connect real and imaginary parts of the frequency-domain response of a system. The K–K relations also hold between the logarithm of modulus and the argument of the response, e.g. between the attenuation and the phase shift of a solution to a wave-propagation problem. For square-integrable functions of frequency, the satisfaction of classical K–K relations implies causality in the time domain....
-
Wybrane aspekty modelowania uderzenia pojazdem dźwigara wiaduktu
PublicationW pracy przedstawiono różne zagadnienia związane z uderzeniem pojazdu w dźwigar wiaduktu. Omówiono wybór modelu obliczeniowego, na podstawie porównania wyników dla modelu dźwigara zespolonego, modelu dźwigara stalowego oraz modelu wiaduktu. Następnie opisano model dźwigara zespolonego zastosowany w analizie MES oraz metodę wyznaczania współczynników tłumienia Rayleigha. Symulację numeryczną uderzenia dźwigara wiaduktu przez koparkę...
-
O zbieżności rozwiązań w nieliniowym mikropolarnym ośrodku sprężysto-plastycznym - zastosowanie elementów skończonych wyższego rzędu.
PublicationEfekty lokalizacji w nieliniowym geometrycznie sprężysto-plastycznym mikropolarnym ośrodku z osłabieniem materiału. Hipotezy Hubera-Misesa-Hencky’ego i Druckera-Pragera. Rozwiązanie równań sprężysto-plastycznych przy użyciu algorytmu powrotnego. Opis zastosowanych elementów skończonych. Przykłady numeryczne obliczeń w geotechnice.
-
Wild oscillations in a nonlinear neuron model with resets: (II) Mixed-mode oscillations
PublicationThis work continues the analysis of complex dynamics in a class of bidimensional nonlinear hybrid dynamical systems with resets modeling neuronal voltage dynamics with adaptation and spike emission. We show that these models can generically display a form of mixed-mode oscillations (MMOs), which are trajectories featuring an alternation of small oscillations with spikes or bursts (multiple consecutive spikes). The mechanism by...
-
Recent advances of selected passive heat transfer intensification methods for phase change material-based latent heat energy storage units: A review
PublicationThe following article overviews recent studies regarding heat transfer enhancement methods, explicitly focusing on fins and coils utilization, in phase change material-based latent heat thermal energy storage systems. It discusses the influence of various geometrical and material parameters on the melting and solidification processes, as well as the orientation of the heat transfer surface within the storage tank. Additionally,...
-
Toward Mechanosynthesis of Diamondoid Structures: IX Commercial Capped CNT Scanning Probe Microscopy Tip as Nowadays Available Tool for Silylene Molecule and Silicon Atom Transfer
PublicationAccording to K. E. Drexler, advanced mechanosynthesis will employ advanced nanomachines, but advanced nanomachines will themselves be product of advanced mechanosynthesis. This circular relationship must be broken in SPM technology development. In the article, the possibility of use easy available commercial CNT tips to assembly silicon-based intermediate generations of nano-devices is considered. Mechanosynthesis of a target class...
-
Identifying the Effects of Selected Road and Roadside Parameters on Road Safety Using Geodetic Techniques
PublicationThe paper will present techniques that can be used to obtain data on road alignment and profile including the roadside. In-the-field and simulation studies have helped to develop mathematical models that integrate vehicle position data. The experiments were conducted in a virtual environment using the software ArcGIS that reflects the actual roadside conditions. The site tests were made using a purpose-built device which integrates...
-
EXPERIMENTAL STUDY OF SURFACE ROUGHNESS EFFECT ONTHE RHEOLOGICAL BEHAVIOR OF MR FLUID
PublicationPaper presents the results of shear stress measurements of a commercial magnetorheological fluid using a plate-plate type geometry with a modified working surface. The purpose of the study was to determine the effect of changing the roughness of the measuring plate on the obtained shear stress results. Controlled shear rate tests and Magneto Sweep measurements were carried out for three MR fluid layer heights. The tests were...
-
The Use of Photographs in the Teaching/Learning of Descriptive Geometry
PublicationThe article presents the concept of enriching the Descriptive Geometry course with photographs and several simplified real-life engineering tasks. The photographic images used for the exercises are tightly linked to engineering structures, the given specialization and the surrounding world. The photo image as a record of central projection of a real space can be useful for presentation and analysis of the properties of perspective....
-
Merging Images From Parallel Depth Cameras
PublicationIn this paper a problem of simultaneous information acquisition from multiple depth cameras is investigated, aiming at obtaining single overall picture containing information from all cameras. The experiments are carried out on Microsoft Kinect devices. A methodology for merging images from multiple positioned in a line cameras is proposed. The method is based on the concept of simulating a view of an imaginary camera covering...
-
Merging Images from Parallel Depth Cameras
PublicationIn this paper a problem of simultaneous information acquisition from multiple depth cameras is investigated, aiming at obtaining single overall picture containing information from all cameras. The experiments are carried out on Microsoft Kinect devices. A methodology for merging images from multiple positioned in a line cameras is proposed. The method is based on the concept of simulating a view of an imaginary camera covering...
-
Voice Maps - portable, dedicated GIS for supporting street navigtion and self-dependent movement of the blind
PublicationThe concept and the prototype application of the system supporting the street navigation and independent, outdoor movement of the blind is presented. The system utilises the GIS database of geometric network of the pedestrian paths in the city and is capable of finding the route from the indicated source to destination. Subsequently, the system supports the movement of the blind along the found route. The information on the user's...
-
Tri-tert-butoksysilanotiolanowe kompleksy cynku(II), kadmu(II) i kobaltu(II) jako modele koordynacji jonu cynku w miejscu aktywnym dehydrogenazy alkoholowej i niektórych innych enzymów
PublicationDehydrogenaza alkoholowa (ADH) katalizuje odwracalne utlenienie alkoholi do aldehydów przy użyciu NAD+ co można podsumować równaniem:R1R2CHOH + NAD+ = R1R2CO + NADH + H+. Geometria koordynacyjna cynku w miejscu aktywnym ADH opisywana jest na ogół jako tetraedryczna jednak istnieją również przesłanki wskazujące na poszerzanie sfery koordynacyjnej metalu w cyklu katalitycznym do LK=5. W pracy przeglądowej opisano badania nad syntetycznymi,...
-
Step on It Bringing Fullwave Finite-Element Microwave Filter Design up to Speed
PublicationThere are many steps in the design of a microwave filter: mathematically describing the filter characteristics, representing the circuit as a network of lumped elements or as a coupling matrix, implementing the distributed elements, finding the initial dimensions of the physical structure, and carrying out numerical tuning using electromagnetic (EM) simulators. The whole process is painstaking and time-consuming, and it requires...
-
Correlation between natural frequencies and buckling load in a stiffened shell
PublicationThe paper deals with correlation between natural frequencies and buckling load of a stiffened shell composed of corrugated sheets and vertical stiffeners (columns). The simplified shell segment represents the buckling behaviour of a whole silo with sparsely distributed columns. The paper covers variants of linear buckling anal-yses, dynamic eigenvalue analyses and geometrically non-linear analyses of a segment modelled with shell...
-
Triangular 3D Laser Scanning in Underwater Photogrammetry
PublicationThe use of triangular 3D laser scanning may significantly enhance the visual inspection of underwater objects. In these days of high demand for accurate information, exclusively photographic documentation is not enough, as it is geometrically flawed. The authors of this article are trying to present the rudiments of laser scanning, a modern means of measuring, which is reliable, relatively easy to use and works in accordance with...
-
A Novel Method for the Deblurring of Photogrammetric Images Using Conditional Generative Adversarial Networks
PublicationThe visual data acquisition from small unmanned aerial vehicles (UAVs) may encounter a situation in which blur appears on the images. Image blurring caused by camera motion during exposure significantly impacts the images interpretation quality and consequently the quality of photogrammetric products. On blurred images, it is difficult to visually locate ground control points, and the number of identified feature points decreases...
-
Entrepreneurship in Virtual Economy: the Case of Currency One SA
PublicationPurpose: The scientific purpose of the study is an attempted synthesis of interpretation of “the virtual economy” and “the virtual environment” in the Polish and foreign literature on the subject. The cognitive purpose thereof is to offer an identification and a qualitative analysis of the factors that determine the development of e-entrepreneurship using an example of business practice. Methodology: The theoretical basis of the...