Filters
total: 1823
filtered: 851
Search results for: CLAMPING DIAMETER
-
Timber frame houses resistant to dynamic loads - seismic analysis
PublicationThe aim of the article is to present results of seismic analysis results of two real-sized timber frame buildings subjected to seismic excitations. The first model was insulated with mineral wool, the second one with polyurethane foam. Technology and specifications involved in both models construction is based on the previously conducted experimental research on timber frame houses, including wall panels tests, wall numerical models...
-
Dynamic tests of composite footbridge segment – experimental and numerical studies
PublicationExperimental dynamic tests and numerical simulations of a 3 meters long segment of a footbridge made of polymer composites are presented in the paper. The span-length is reduced, however dimensions of cross-section are the same as the target footbridge. The segment structure is made of sandwich panels, which consist of fibre reinforced polymer (GFRP) laminates (skins) and a PET foam (core). The first part of the paper contains...
-
Planning, Configuration and Usefulness of Microseismic Monitoring on Eastern-Europe Platform – Example from East Pomerania
PublicationThe microseismic monitoring is a method of monitoring of fracture propagation during hydraulic fracturing process. The method uses array of geophones to localize micro tremors induced by liquid pumped underground at high rate and pressure. The acquired information helps to optimize fracturing process and prevents fracture growth to aquifer levels. It proved to be useful on several unconventional hydrocarbon reservoirs in the USA....
-
CONSTRUCTION TECHNOLOGY OF TIMBER-FRAME HOUSES RESISTANT TO DYNAMIC LOADS – STUDY ON MODELS OF EXTERIOR WALLS
PublicationThe aim of this paper is to show the numeric representation of experimental studies concerning the behaviour of exterior wall models of a timber-frame house under harmonic loading. A single wall model according to traditional technology of timberframe house walls (filling with mineral wool) was tested. The analysis was conducted for the following frequencies: 0.5 Hz, 1.0 Hz, 2.0 Hz and 5.0 Hz for various values of the specified...
-
The influence of temperature on properties of the polymer flexible joint used for strengthening historical masonries
PublicationA new method of repairing damaged structures by filling the cracks with a specially prepared elastomeric polymer mass has been recently proposed. This new and innovative technique, known as the Flexible Joint Method (FJM), is mainly dedicated to masonries and historical objects, where minimum intervention is permitted. The flexible joint bonds the disrupted elements and ensures further safe exploitation of a damaged structure....
-
Footbridges. Dynamic Design – Selected Problems
PublicationModern footbridges create challenge in esthetic and structural design. Breaking the proven canons is a recipe for architectural success. However esthetic form has to be also a functional pedestrian bridge. Therefore a good FEM modeling is a key element in engineering part of design. The paper presents selected problems related to the modeling of the dynamic construction of footbridges. Several basic dynamic problems concerning...
-
Mathematical Modelling of a Seismic Isolation System to Protect Structures During Damaging Earthquakes
PublicationThe present study aims to determine the effectiveness of a nonlinear mathematical model in simulating complex mechanical behaviour of a seismic isolation system to protect structures during strong and damaging earthquakes. In order to construct the Polymeric Bearings considered in this research, a specially prepared flexible polyurethane elastomer with increased damping properties has been used. The usefulness of the proposed mathematical...
-
Analysis of the Hydrodynamic Properties of the 3-Column Spar Platform for Offshore Wind Turbines
PublicationThe article presents a design of a floating platform for offshore wind turbines. The concept is a modification of the Spar design and consists of three variable section columns connected to each other by a ballast tank in the lower part of the platform. This solution makes it possible to influence the position of the centre of buoyancy and the centre of mass of the structure. Compared to the classic Spar platform structure, the...
-
HEAVE MOTION OF A VERTICAL CYLINDER WITH HEAVE PLATES
PublicationThe shape of a vertical cylinder resembles the classic form of a spar platform. Spar platforms are floating platforms that are successfully used in waters of great depths and have several advantages that mean they are readily used in the oil industry. Many of these advantages are also relevant to their application for offshore wind turbines, which is currently being considered. In the hydrodynamic analysis of spar platforms, the...
-
Damage Detection in the Wind Turbine Blade Using Root Mean Square and Experimental Modal Parameters
PublicationThe paper presents results of an experimental study related to a non-destructive diagnostic technique used for preliminary determination the location and size of delamination in composite coatings of wind turbine blades. The proposed method of damage detection is based on the analysis of the ten first mode shapes of bending vibrations, which correspond to displacements of rotor blades perpendicular to the rotor plane. Modal parameters...
-
TiO 2 Co x O y composite nanotube arrays via one step electrochemical anodization for visible light–induced photocatalytic reaction
PublicationTiO2CoxOy (x = 1, y = 1 or x = 3, y = 4) composite photocatalysts have been synthesized via one step anodic anodization of TiCo alloys. The effects of the cobalt content in the alloy (5, 10 and 15 wt%), water content (2, 5 and 10%) in the electrolyte solution, and applied voltage (30, 40 and 50 V) during the anodization process on the morphology and surface properties. Additionally, the dependence of cobalt content in the nanotubes...
-
The influence of small intestinal mucus structure on particle transport ex vivo
PublicationMucus provides a barrier to bacteria and toxins while allowing nutrient absorption and waste transport. Unlike colonic mucus, small intestinal mucus structure is poorly understood. This study aimed to provide evidence for a continuous, structured mucus layer and assess the diffusion of different sized particles through it. Mucus structure was assessed by histology and immunohistochemistry. Ultra-structure was assessed by scanning...
-
Pool boiling of nanofluids on rough and porous coated tubes: experimental and correlation
PublicationThe paper deals with pool boiling of water-Al2O3 and water- Cu nanofluids on rough and porous coated horizontal tubes. Commercially available stainless steel tubes having 10 mm outside diameter and 0.6 mm wall thickness were used to fabricate the test heater. The tube surface was roughed with emery paper 360 or polished with abrasive compound. Aluminium porous coatings of 0.15 mm thick with porosity of about 40% were produced by...
-
Effect of irradiation intensity and initial pollutant concentration on gas phase photocatalytic activity of TiO2 nanotube arrays
PublicationWell-organized TiO2 nanotube arrays were fabricated via one-step anodization process. The as-prepared TiO2 nanotubes were characterized by X-ray powder diffractometry (XRD), X-ray photoelectron spectroscopy (XPS), diffuse reflectance spectroscopy (DRS) and scanning electron microscopy (SEM). Photocatalytic activity of obtained photocatalyst was studied in reaction of toluene degradation in the gas phase using low powered and low...
-
Modeling of Cardiac Component of Subarachnoid Space Changes in Apnoea Resulting as a Function of Blood Pressure and Blood Flow Parameters - Two Mechanizm of Regulation
PublicationExperiments were performed in a group of 19 healthy, non-smoking volunteers. The experiment consisted of three apnoeas, sequentially: 30 s apnoea, 60 s apnoea and maximal, that could be done, apnoea. The breath-hold was separated for 5 minutes rest. The following parameters were measured and obtained for further analysis: blood parameters, artery diameter of the internal carotid artery, end-tidal CO2 in expired air, the cardiac...
-
Research on water lubricated main shaft bearings in conditions of improper lubrication and cooling conducted on high torque real-life scale bush test rig
PublicationWater lubricated polymer bushes find increasingly popular use in the sliding bearings of marine propellers, water turbines and pump shafts. Such popularity is partly due to their simple construction which also means relatively affordable price. In addition, properly designed and installed water lubricated bearings may well last for over a decade. However, in practical experience one may also observe cases of rapid wear...
-
Natural convective heat transfer from isothermal cuboids
PublicationThe paper presents results of theoretical and experimental investigations of the convective heat transfer from isothermal cuboid. The analytical solution was performed taking into account complete boundary layer length and the manner of its propagation around isothermal cuboid. It arises at horizontal bottom surface and grows on vertical lateral surface of the block. After changing its direction, the boundary layer occurs above...
-
Safety and efficacy of a Ventralight ST echo ps implant for a laparoscopic ventral hernia repair – a prospective cohort study with a one-year follow-up
Publicationing new products Thus, every mesh prior to introduction in clinical settings should be tested with a dedicated tacker to discover the proper fixation algorithm. The aim of the study was to assess the safety and efficacy of the Ventralight ST implant with an ECHO positioning system and a dedicated fixation device, the SorbaFix stapler, in a prospective cohort of patients. Material and methods. The study was a prospective single...
-
Chlorine-free extraction and structural characterization of cellulose nanofibers from waste husk of millet (Pennisetum glaucum)
PublicationThis study aims to extract cellulose nanofibers (CNFs) from a sustainable source, i.e. millet husk, which is an agro-waste worthy of consideration. Pre-treatments such as mercerisation, steam explosion, and peroxide bleaching (chlorine-free) were applied for the removal of non-cellulosic components. The bleached millet husk pulp was subjected to acid hydrolysis (5% oxalic acid) followed by homogenization to extract CNFs. The extracted...
-
A Proposed Soft Computing Model for Ultimate Strength Estimation of FRP-Confined Concrete Cylinders
PublicationIn this paper, the feed-forward backpropagation neural network (FFBPNN) is used to propose a new formulation for predicting the compressive strength of fiber-reinforced polymer (FRP)-confined concrete cylinders. A set of experimental data has been considered in the analysis. The data include information about the dimensions of the concrete cylinders (diameter, length) and the total thickness of FRP layers, unconfined ultimate concrete...
-
The effect of imidazolium ionic liquid on the morphology of Pt nanoparticles deposited on the surface of SrTiO3 and photoactivity of Pt–SrTiO3 composite in the H2 generation reaction
PublicationPhotocatalytic water splitting has great potential in solar-hydrogen production as a low-cost and environmentally friendly method. Different unique techniques used to obtain photocatalysts with various modifications to improve H2 generation have been introduced. In the present work, SrTiO3 was successfully synthesized via the solvothermal method in the presence of ionic liquid (IL) - 1-butyl-3-methylimidazolium bromide ([BMIM][Br])...
-
Rapid development of the photoresponse and oxygen evolution of TiO2 nanotubes sputtered with Cr thin films realized via laser annealing
PublicationRecently, earth abundant transition metal oxides have gained particular attention as potential catalyst candidates due to their availability and low-cost comparing to substrates containing precious Pt or Au species. Herein, we present characterization of morphology, structure and electrochemical properties of pulsed 532 nm laser treated TiO2 nanotubes (NT) sputtered by the thin film of chromium. Scanning electron microscopy enables...
-
Multi-objective optimization of the cavitation generation unit structure of an advanced rotational hydrodynamic cavitation reactor
PublicationHydrodynamic cavitation (HC) has been widely considered a promising technique for industrial-scale process intensifications. The effectiveness of HC is determined by the performance of hydrodynamic cavitation reactors (HCRs). The advanced rotational HCRs (ARHCRs) proposed recently have shown superior performance in various applications, while the research on the structural optimization is still absent. The present study, for the...
-
Generalization of Phylogenetic Matching Metrics with Experimental Tests of Practical Advantages
PublicationThe ability to quantify a dissimilarity of different phylogenetic trees is required in various types of phylogenetic studies, for example, such metrics are used to assess the quality of phylogeny construction methods and to define optimization criteria in supertree building algorithms. In this article, starting from the already described concept of matching metrics, we define three new metrics for rooted phylogenetic trees. One...
-
Application of spectroscopy to the measurement of blood parameters
PublicationSpectroscopy is the study of formation and interpretation of the spectra arising from the interactions of all types of radiation on matter, understood as a collection of atoms and molecules. This is a very important department of optics which gives us many opportunities to measure various parameters such as material blood parameters. Among the diseases that are associated significantly with changes in rheological properties of...
-
Non-destructive inspection of ground anchors using guided wave propagation
PublicationThis paper deals with numerical and experimental investigations of specific problems of guided wave propagation in ground anchors. The research focuses on recognizing the phenomenon of the energy transfer between anchor components. Particular attention is paid to characteristic features of guided waves propagating in free and embedded parts of the tendon, at the interface between the tendon and the surrounding anchor body as well...
-
A novel method for drop in drop edible oils encapsulation with chitosan using a coaxial technique
PublicationThe presented work concerns a novel one step method for oil encapsulation. In this coaxial system the oil constitutes the core of the capsule, while the chitosan solution is the polymer shell surrounding the core to provide separation of the core from the external environment. The paper contains a diagram of the encapsulation equipment and explains the principle of its operation. The experimental results showed the impact of the...
-
Three-dimensional characterization of porosity in iron ore pellets: A comprehensive study
PublicationThis paper presents a comprehensive study on the production and reduction of high-quality iron ore pellets characterized by a basicity index nearing 0.5 and diameters ranging from 1 to 2 cm. The reduction process was carried out in a hydrogen atmosphere at temperatures spanning 800–1000 ◦ C and a pressure of 8 bar. Initial f indings revealed substantial variations in pellet density and compressive strength, attributed to their...
-
Quantification of ultrafine airborne particulate matter generated by the wear of car brake materials
PublicationThe wear of car brakes is one of the main sources of airborne particulate matter in urban environments. Ultrafine wear particles are of special environmental interest since they can easily penetrate the human body through inhalation and cause various diseases. In the present study, the contribution of ultrafine particles to airborne particulate matter emitted from car brake materials was investigated under different friction conditions....
-
Nanotubular Oxide Layer Formed on Helix Surfaces of Dental Screw Implants
PublicationSurface modification is used to extend the life of implants. To increase the corrosion resistance and improve the biocompatibility of metal implant materials, oxidation of the Ti-13Nb- 13Zr titanium alloy was used. The samples used for the research had the shape of a helix with a metric thread, with their geometry imitating a dental implant. The oxide layer was produced by a standard electrochemical method in an environment of...
-
Non-invasive blood glucose monitoring with Raman spectroscopy: prospects for device miniaturization
PublicationThe number of patients with diabetes has reached over 350 million, and still continues to increase. The need for regular blood glucose monitoring sparks the interest in the development of modern detection technologies. One of those methods, which allows for noninvasive measurements, is Raman spectroscopy. The ability of infrared light to penetrate deep into tissues allows for obtaining measurements through the skin without its...
-
CONTROL OF THE WAVES IN A TOWING TANK WITH THE USE OF A BLACK-BOX MODEL
PublicationThe paper describes an adaptive control system of the waves, implemented in the Ship Design and Research Centre, CTO S.A. The purpose of generating the waves in the towing tank is the modelling of the environmental conditions during hydrodynamic model tests. The tests are performed on scale models of towed or free running ships, anchored structures like oil rigs or bottommounted structures, e.g. wind turbines. In the towing tank...
-
Non-linear behaviour of base-isolated building supported on flexible soil under damaging earthquakes
PublicationSeismic isolation is a strategy to reduce damage of structures exposed to devastating earthquake excitations. Isolation systems, applied at the base of buildings, lower the fundamental frequency of the structure below the range of dominant frequencies of the ground motion as well as allow to dissipate more energy during structural vibrations. The effectiveness of the base-isolated buildings in damage reduction has been confirmed...
-
Numerical study on seismic response of a base-isolated building modelled with shell elements
PublicationSeismic isolation is counted among the most popular and effective means of protecting structures against earthquake forces. Base isolators, like Lead-Rubber Bearings (LRB), High-Damping Rubber Bearings (HDB) or Friction Pendulum Systems (FPS) are extensively used in practice in many earthquake-prone regions of the world. The present paper reports the results obtained from the numerical study on seismic response of a base-isolated...
-
Properties of Thermally Dewetted Thin Au Films on ITO-Coated Glass for Biosensing Applications
PublicationNoble metal nanostructures are object of great interest due to their unique optical and electronic properties exploited in nanotechnology, medicine, biochemistry, and surface-enhanced spectroscopies. In this work, the Au nanoparticle (NP) structures for application in biosensing obtained by dewetting are investigated in dependence on their preparation conditions. Structures are produced from thin Au films (5–30 nm) sputtered onto...
-
Application of Structural Control Systems for the Cables of Cable-Stayed Bridges: State-of-the-Art and State-of-the-Practice
PublicationStay cables are one of the key elements of cable-stayed bridges and are characterized by lightweight, low inherent damping, and high flexibility. They are continuously subjected to small-to large-amplitude vibrations due to various types of dynamic loads that may, in the long term, cause fatigue and fracture problems for the cable system, and may eventually compromise the safety of cable-stayed bridges. Thus, several countermeasures...
-
Identification of ship’s hull mathematical model with numerical methods
PublicationThe modern maritime industry is moving toward the development of technology that will allow for full or partial autonomy of ship operation. This innovation places high demands on ship performance prediction techniques at the design stage. The researchwork presented in the article is related to the design stage of the ship and concerns methods for prognosis and evaluation of the specific operational condition of the ship, namely...
-
On the Dynamics of a Visco–Piezo–Flexoelectric Nanobeam
PublicationThe fundamental motivation of this research is to investigate the effect of flexoelectricity on a piezoelectric nanobeam for the first time involving internal viscoelasticity. To date, the effect of flexoelectricity on the mechanical behavior of nanobeams has been investigated extensively under various physical and environmental conditions. However, this effect as an internal property of materials has not been studied when the...
-
A dynamic vehicle-bridge model based on the modal identification results of an existing EN57 train and bridge spans with non-ballasted tracks
PublicationThis paper addresses the methodology of the bridge-vehicle dynamic model definition based on the free response measurements of an existing train and existing bridge spans. In the case of the railway vehicle, the methodology uses the impulse excitations of a single car by means of the wedge method. In the case of the bridge spans, free responses are collected after the passages of trains. The global modal parameters (frequencies...
-
Study on applicability of two modal identification techniques in irrelevant cases
PublicationStudy on applicability of two modal identification techniques in irrelevant cases is made in this paper. The following techniques are considered: Peak Picking based on correlation analysis (PP-CA), dedicated for ambient vibrations and Eigensystem Realization Algorithm (ERA), formulated for free decay vibrations investigation. Irrelevant cases are found when analyzed signals are different than recommended to a given technique. The...
-
Effective Gap Size Index for Determination of Optimum Separation Distance Preventing Pounding between Buildings during Earthquakes
PublicationSeismic excitations may lead to collisions between adjacent civil engineering structures causing major damage. In this paper, an effective equation for calculating the gap size index is proposed so as to provide the optimum separation distance preventing structural pounding during different earthquakes. Evaluation of the best prediction of the required separation distance between two adjacent buildings was carried out by using...
-
Channel Blockage and Flow Maldistribution during Unsteady Flow in a Model Microchannel Plate heat Exchanger
PublicationThis paper describes the problem of channel blockage as a result of flow maldistribution between the channels of a model mini channel plate heat exchanger consisting of one pass on each leg. Each leg of the heat exchanger contains 51 parallel and rectangular minichannels of four hydraulic diameters namely 461 μm, 571 μm, 750 μm and 823 μm. In addition, a more complex geometry has been investigated where for the sake of breaking...
-
The influence of the fuel spray nozzle geometry on the exhaust gas composition from the marine 4-stroke diesel engine
PublicationThe paper presents experimental research on a 4-stroke, 3-cylinder, turbocharged AL25/30 Diesel engine. Research consisted in investigating the effect of the geometry of the fuel injectors on the exhaust gas composition from the engine. During measurements, the engine was operated with a regulator characteristic of a load range from 40 kW to 280 kW, made by electric water resistance. The engine was mechanically coupled to the electric...
-
Pressure drop related to flow maldistribution in a model minichannel plate heat exchanger
PublicationThe paper describes the issues related to the pressure drop that accompanies the phenomenon of maldistribution of working fluid between the channels of a model minichannel plate heat exchanger. The research concerns a single exchanger's plate containing 51 (in every geometry) parallel rectangular minichannels of hydraulic diameters 461 µm, 571 µm, 750 µm and 823 µm. In addition, the more complex geometry has been investigated,...
-
Discouraging Traffic Remapping Attacks in Local Ad Hoc Networks
PublicationQuality of Service (QoS) is usually provided in ad hoc networks using a class-based approach which, without dedicated security measures in place, paves the way to various abuses by selfish stations. Such actions include traffic remapping attacks (TRAs), which consist in claiming a higher traffic priority, i.e., false designation of the intrinsic traffic class so that it can be mapped onto a higher-priority class. In practice, TRAs...
-
Processes of enhancing the intelligence of Learning Organizations on the basis of Competence Centers
PublicationThe process of organizational learning and proper knowledge management became today one of the major challenges for the organization acting in the knowledge-based economy. According to the observations of the authors of this paper the demand for formalization of knowledge management processes and organizational learning is particularly evident in research institutions, established either by the universities, or the companies. The...
-
On topology optimization of large deformation contact-aided shape morphing compliant mechanisms
PublicationA topology optimization approach for designing large deformation contact-aided shape morphing compliant mechanisms is presented. Such mechanisms can be used in varying operating conditions. Design domains are described by regular hexagonal elements. Negative circular masks are employed to perform dual task, i.e., to decide material states of each element and also, to generate rigid contact surfaces. Each mask is characterized by...
-
Stabilizing forces in trapezoidal sheeting used as a part of the bracing system
PublicationIn the analysis of bracing systems imperfections of the restrained elements should be considered. According to EC3 this effect can be calculated by means of the equivalent stabilizing force, which replaces (in simplified way) initial bow imperfection of the braced element. However, alternative suggestions of the equivalent stabilizing force calculations can be also found in the literature. In this paper segment of the pitched roof...
-
Stabilizing forces in trapezoidal sheeting used as a part of the bracing system
PublicationIn the analysis of bracing systems imperfections of the restrained elements should be considered. According to EC3 this effect can be calculated by means of the equivalent stabilizing force, which replaces (in simplified way) initial bow imperfection of the braced element. However, alternative suggestions of the equivalent stabilizing force calculations can be also found in the literature. In this paper segment of the pitched roof...
-
Solid state versus fiber picosecond infrared lasers applied to two-photon vision tests
PublicationDevelopment of new microperimetric tools dedicated for imaging of early functional changes in the retina may help in the monitoring of various ocular diseases progression e.g. Age-Related Macular Degeneration. Recently described two-photon vision may be applied to microperimetric devices. Many subjects with well-known disease history could be investigated with newly developed instrumentation that tests ability of human eye to perceive...