Filters
total: 2186
filtered: 1834
displaying 1000 best results Help
Search results for: SELFISH BEHAVIOR
-
Influence of stirrups in a concrete shell on strengthening reinforced concrete column
PublicationTwelve concrete columns, with a 150x150mm square section and three columns with a circular section (d=200mm), are tested to investigate the effect of strengthening by RC jacket. Based on a confined concrete model for axial static loading, an analytical methods, reported in the literature are proposed to predict the behavior of columns with RC jacket. The results support the conception that the effect of strengthening depends...
-
A first-principles study of electron attachment to the fully hydrated bromonucleobases
PublicationDegradation mechanism of four brominated nucleobases (BrX), potential DNA radiosensitizers, is studied in explicit water solution, using ab initio molecular dynamics. Several fs long dynamics is needed to localize an electron on the nucleobase. Produced by electron attachment BrX anion radical degrades through the bromide anion abstraction, barrier-free (purines) or with low barrier (pyrimidines), to a reactive nucleobase radical....
-
The smoothness test for a density function
PublicationThe problem of testing hypothesis that a density function has no more than μ derivatives versus it has more than μ derivatives is considered. For a solution, the L2 norms of wavelet orthogonal projections on some orthogonal ‘‘differences’’ of spaces from a multiresolution analysis is used. For the construction of the smoothness test an asymptotic distribution of a smoothness estimator is used. To analyze that asymptotic distribution,...
-
Dynamic Tests and Technical Monitoring of a Novel Sandwich Footbridge
PublicationA novel sandwich composite footbridge is described in this paper, for the first time after it has been put into operation over the Radunia River in the Pruszcz Gdański municipality. This paper presents results of dynamic tests and describes technical monitoring of the footbridge. The dynamic tests were conducted to estimate pedestrian comfort and were compared with the ones from numerical simulations made in the environment of...
-
Mieszanie w klasie niejednorodnych łańcuchów Markowa i kwadratowych operatorów stochastycznych
PublicationRozprawa doktorska poświęcona jest zagadnieniu asymptotycznych własności w klasie nieskończenie wymiarowych niejednorodnych łańcuchów Markowa z czasem dyskretnym oraz w klasie kwadratowych operatorów stochastycznych. W pierwszej kolejności definiowane są różne rodzaje asymptotycznego zachowania (mieszania) niejednorodnych łańcuchów Markowa odpowiadające zbieżności w normowej i mocnej topologii operatorowej oraz omówione są relacje...
-
Example of tension fabric structure analysis
PublicationThe aim of the work is to examine two variants of non-linear strain-stress relations accepted to description of architectural fabric. Discussion on the fundamental equations of the dense net model, used in description of coated woven fabric behaviour is presented. An analysis of tensile fabric structures subjected to the dead load and initial pretension is described.
-
Degradation of stiffness of building columns exposed to bending and impact load during ground motions
PublicationThe safety of civil engineering structures under external loads, including ground motions, is one of the issues related to the idea of sustainable society. The earthquake-induced soft-storey failure is a typical type of damage observed in buildings due to seismic excitation. The failure of an intermediate soft storey of a structure results in large vertical impact loading acting on the lower floors due to the fall of the upper...
-
REVISING ENTREPRENEURIAL ORIENTATION (EO) IN SOCIAL ENTREPRENEURSHIP, QUALITATIVE EVIDENCE FROM WORK INTEGRATION SOCIAL ENTERPRISES (WISES) FROM POLAND
PublicationEntrepreneurial behaviour and entrepreneurial orientation (EO) of (commercial) entrepreneurship. have received significant scholarly attention in entrepreneurship and management research However, there are insufficient attempts discussing such behaviour and EO in non-profit, and particularly social entrepreneurship context, arguing that EO is higher in such contexts, or remains the same, some new EO dimensions are proposed, existing...
-
Simulating Malware with MAlSim
PublicationThis paper describes MAlSim - Mobile Agent Malware Simulator - a mobile agent framework developed to address one of the most important problems related to the simulation of attacks against information systems i.e. the lack of adequate tools for reproducing behaviour of malicious software (malware). The framework can be deployed over the network of an arbitrary information system and it aims at simulating behaviour of each instance...
-
Simulating malware with MAlSim
PublicationThis paper describes MAlSim - Mobile Agent Malware Simulator - a mobile agent framework developed to address one of the most important problems related to the simulation of attacks against information systems, i.e. the lack of adequate tools for reproducing behaviour of malicious software (malware). The framework can be deployed over the network of an arbitrary information system and it aims at simulating behaviour of each instance...
-
Surface and interfacial anti-plane waves in micropolar solids with surface energy
PublicationIn this work, the propagation behaviour of a surface wave in a micropolar elastic half-space with surface strain and kinetic energies localized at the surface and the propagation behaviour of an interfacial anti-plane wave between two micropolar elastic half-spaces with interfacial strain and kinetic energies localized at the interface have been studied. The Gurtin–Murdoch model has been adopted for surface and interfacial elasticity....
-
ZNACZENIE ŹRÓDEŁ POCZUCIA SAMOSKUTECZNOŚCI U POCZĄTKUJĄCYCH PRZEDSIĘBIORCÓW – RAPORT Z BADAŃ
PublicationPoczucie samoskuteczności w sposób istotny wpływa na zachowanie ludzi sprawiając, że stają się oni bardziej wytrwali w działaniu i stawiają sobie ambitne cele. Poczucie samoskuteczności powstaje pod wpływem doświadczeń jednostki, a jego poziom jest możliwy do kształtowania. Zdaniem Bandury (1997) istnieją cztery źródła poczucia samoskuteczności, czyli poprzednie doświadczenie, pobudzenie fizjologiczne, obserwacja innych oraz perswazja....
-
GTR/Thermoplastics Blends: How Do Interfacial Interactions Govern Processing and Physico-Mechanical Properties?
PublicationIn this work, GTR/thermoplastics blends (in ratio 50/50 and 75/25 wt.%) were prepared by melt-compounding in an internal mixer. During research, trans-polyoctenamer rubber (TOR), ethylene-vinyl acetate copolymer (EVA), ethylene-octene copolymer (EOC), and linear low-density polyethylene (LLDPE), were used in their thermoplastic phase. Microstructure and processing-performance property interrelationships of the studied materials...
-
CERTIFICATION SYSTEM AS A TOOL FOR IMPROVING THE SAFETY AND SUSTAINABILITY OF SCHOOL-RELATED TRAVELS
PublicationDespite the well-established physical, social, emotional, cognitive, and spatial benefits of active and autonomous school commuting of children and adolescents', many are driven by car. Pilot surveys and field research held in 2019 in 10 Gdansk primary schools confirmed this trend. The article presents a certification system for schools, commissioned by the City of Gdańsk, which is an element of a systemic solution shaping patterns...
-
Thermal degradation of polylactic acid (PLA)/polyhydroxybutyrate (PHB) blends: A systematic review
PublicationPolylactic acid (PLA) and polyhydroxybutyrate (PHB) are two biopolyesters obtained from renewable resources like corn or sugar under bacterial fermentation. PLA is the most widely used biopolymer in diverse applications. Addition of PHB to PLA can improves the crystallinity of PLA, and thereby its mechanical strength. However, both PLA and PHB suffer from poor thermal stability, which limits their potential industrial application....
-
Stiffness of cold-recycled mixtures under variable deformation conditions in the IT-CY test
PublicationStiffness modulus belongs to the most important properties describing the cold-recycled mixtures (CRM) in terms of their usability in road pavement structures. Previous research proved that this property is strongly dependent on the scheme and conditions of the test (temperature and time of loading) and the time that has passed since the compaction of the specimen or pavement layer. It is a result of the influence of two different...
-
Evaluation and rationale of the performance of several elastomeric composites incorporating devulcanized EPDM
Publicationthylene Propylene Diene rubber (EPDM), is present in many applications. However, its crosslinked structure makes difficult its recycling. The use of devulcanized EPDM, (dEPDM) as a component of elastomeric composites, is a real possibility to reuse EPDM scraps. In this study, three matrices (natural rubber (NR), styrene butadiene rubber (SBR) and EPDM rubber) have been tested including devulcanized EPDM as a recycled component....
-
Linear viscoelastic transversely isotropic model based on the spectral decomposition of elasticity tensors
PublicationThe linear viscoelasticity is still a useful model in the engineering for studying the behavior of materials loaded with different loading rates (frequencies). Certain types of materials reveal also an anisotropic behavior: fiber reinforced composites, asphalt concrete mixtures, or wood, to name a few. In general, researchers try to identify experimentally the dependence of engineering constants like: directional Young’s moduli...
-
Wielkopowierzchniowe obiekty handlowe - zwykłe generatory ruchu czy źródła problemów transportowych?
PublicationW artykule zaprezentowano dane na temat funkcjonowania dużych centrów handlowych w miastach, uzyskane z polskich i obcojęzycznych źródeł literatury oraz badań realizowanych w Polsce i za granicą. Przedstawione zagadnienia pozwalają na zapoznanie się z podstawową wiedzą na temat zachowań klientów oraz poznanie uwarunkowań określania oferty parkingowej wielkopowierzchniowych obiektów handlowych. Przedstawiono także charakterystyki...
-
Titanium Scaffolds – Hopes and Limitations
PublicationThe state-of-art on titanium scaffolds is briefly reviewed. The real hopes from medicine associated with scaffolds are indicated. The limitations of different scaffolds associated with their mechanical, chemical and biological properties are discussed. The great importance of titanium scaffolds is demonstrated as the materials of high biocompatibility and corrosion resistance, fair mechanical properties and important biological...
-
Effect of initial imperfection on buckling of thin-walled I columns
PublicationEffects of initial geometrical imperfections on critical buckling loads of thin-walled I columns are investigated. Torsional and flexural buckling are taken into account. The column behaviour is described in accord to the theory of thin-walled beams with nondeformable cross-section. Some numerical examples and conclusions related to effects of imperfections on properties of the critical loads are presented.
-
Effect of illumination on noise of silicon solar cells
PublicationTransport and noise properties of silicon solar cells in darkness and under illumination have been studied. The measurements were carried out for both reverse and forward bias of the device. The changes in the sample behaviour are due to the variation of PN junction dynamic resistance and, also, the occurence of both 1/f and generation-recombination noise components
-
Prevalence Problem in the Set of Quadratic Stochastic Operators Acting on L1
PublicationThis paper is devoted to the study of the problem of prevalence in the class of quadratic stochastic operators acting on the L1 space for the uniform topology. We obtain that the set of norm quasi-mixing quadratic stochastic operators is a dense and open set in the topology induced by a very natural metric. This shows the typical long-term behaviour of iterates of quadratic stochastic operators.
-
Using Different Information Channels for Affect-Aware Video Games - A Case Study
PublicationThis paper presents the problem of creating affect-aware video games that use different information channels, such as image, video, physiological signals, input devices, and player’s behaviour, for emotion recognition. Presented case studies of three affect-aware games show certain conditions and limitations for using specific signals to recognize emotions and lead to interesting conclusions.
-
A method for counting people attending large public events
PublicationThe algorithm for people counting in crowded scenes, based on the idea of virtual gate which uses optical flow method is presented. The concept and practical application of the developed algorithm under real conditions is depicted. The aim of the work is to estimate the number of people passing through entrances of a large sport hall. The most challenging problem was the unpredicted behavior of people while entering the building....
-
Electrical and structural properties of Nb-doped SrTiO3
PublicationNiobium-doped strontium titanate synthesized via conventional solid-state reaction has been studied. Influence of niobium content on the lattice parameters and electrical conductivity has been reported. Various reduction conditions have been investigated. For samples reduced in hydrogen at 1400°C, a transition from thermally activated to metallic behavior has been observed. Maximum electrical conductivity (ca. 55 Scm−1 at 650°C)...
-
Reference FEM model for SHM system of cable-stayed bridge in Rzeszów
PublicationThe paper presents the references model for structural health monitoring system (SHM) of cable-stayed bridge recently constructed in Rzeszów over Wisłok River. The SHM system is design to provide on-line information on the structure state and facilitate its maintenance procedures. The main feature of the SHM system is permanent observation of the dynamic behavior of the bridge with focus on cable vibrations. The paper discusses...
-
A novel sandwich footbridge - Practical application of laminated composites in bridge design and in situ measurements of static response
PublicationA novel sandwich composite footbridge is presented in the paper, as an example of practical application of laminated composites in civil engineering. The in situ static load tests of the footbridge before its acceptation for exploitation are shown and discussed. The results are compared with the corresponding ones from a numerical equivalent single layer model of the sandwich structure created within the framework of finite element...
-
Application of virtual gate for counting people participating in large public events
PublicationThe concept and practical application of the developed algorithm forpeople counting in crowded scene is presented. The aim of the work is to estimatethe number of people passing towards entrances of a large sport hall. Thedetails of implemented the Virtual Gate algorithm are presented. The video signalfrom the camera installed in the building constituted the input for the algorithm.The most challenging problem was the unpredicted...
-
From flow to jamming: Lattice Gas Automaton simulations in granular materials
PublicationWe introduce the first extension of a Lattice Gas Automaton (LGA) model to accurately replicate observed emergent phenomena in granular materials with a special focus on previously unexplored jamming transitions by incorporating gravitational effects, energy dissipation in particle collisions, and wall friction. We successfully reproduce flow rate evolution, density wave formation, and jamming transition observed in experiments....
-
Theoretical analysis of the cable-stayed bridge over brda river in Bydgoszcz
PublicationThe topic of this article is the numerical analysis carried out for the cable-stayed tram (road) bridge over Brda river in Bydgoszcz. The goal of numerical studies was the verification of project assumptions and construction solutions elaborated by the autonomous team. The bridge calculations were conducted on three independent FEM models The internal forces and the elements effort under different loading schemes were examined....
-
FE analysis of support-specimen interaction of compressive experimental test
PublicationThe objective of this work is to investigate the support-specimen interaction during the compressive experimental testing of stiffened plates. The interaction is analyzed employing the nonlinear Finite Element Method using the commercial software ANSYS. The connection between the stiffened plate and testing supports is modelled with the use of contact elements, where several possible interaction scenarios are investigated, and...
-
MaliciousIDE – software development environment that evokes emotions
PublicationEmotions affect every aspect of human live, including work. Numerous studies in software engineering have shown that negative emotions can lower the productivity of programmers. Unlike traditional approaches to managing software development, modern methods, such as Agile and Lean, take into account human aspects of programming. To thoroughly investigate the impact of negative emotions on the work of programmers, a malicious integrated...
-
Typologia aktywności online konsumenta w zakresie marki
PublicationWeb 2.0 daje konsumentom nieograniczone możliwości wchodzenia w interakcje, wypowiadania się, udostępniania oraz kreowania treści dotyczących produktów i marek. Tego typu aktywność konsumentów, która ma miejsce w Internecie (tzw. COBRA), stanowi wielką wartość dla firm. Niniejszy artykuł stanowi pierwszą próbę przedstawienia pełnej klasyfikacji tego typu zachowań w trzech głównych kategoriach (konsumpcji, kontrybucji i kreacji),...
-
THE ROLE OF THE POLISH UNIVERSITIES IN SHAPING A NEW MOBILITY CULTURE - ASSUMPTIONS, CONDITIONS, EXPERIENCE. CASE STUDY OF GDANSK UNIVERSITY OF TECHNOLOGY, CRACOW UNIVERSITY OF TECHNOLOGY AND SILESIAN UNIVERSITY OF TECHNOLOGY
PublicationThe article expresses an idea of the privileged role of universities in the process of shaping the new culture for urban mobility. Mobility management of the academic community is adopted in order to indirectly influence a wider group of the population. The aim of the study was to investigate the situation at the Polish universities and the willingness of their authorities to implement integrated tools to manage the transportation...
-
Pounding between Inelastic Three-Storey Buildings under Seismic Excitations
PublicationStructural interactions between adjacent, insufficiently separated buildings have been repeatedly observed during damaging ground motions. This phenomenon, known as the structural pounding, may result in substantial damage or even total collapse of structures. The aim of the present paper is to show the results of the nonlinear numerical analysis focused on pounding between inelastic three-storey buildings under seismic excitations....
-
Experimental determination of basic mechanical properties of elastomeric polymer
PublicationThere are a lot of different methods of repairing and reinforcing damaged structures, but when it comes to historical buildings and other cultural heritage objects, it is as much about mechanical safety as the aesthetical aspects. Recently, a new and innovative method of repairing damaged structures by filling the cracks with a specially prepared polymer mass has been proposed. This new and innovative technique, known as the Flexible...
-
Shear band evolution phenomena in direct shear test modelled with DEM.
PublicationA direct shear test is widely used in the geotechnical engineering field. It is an easy and quick test to measure the shear properties of soil. This test often replaces more expensive and difficult tri-axial shear test. Despite that the direct shear test is known and used for a long time, it is still not well investigated at the grain scale. This paper deals with the micro behaviour of the cohesionless sand inside the direct shear...
-
Experimental and numerical investigations of ultimate strength of imperfect stiffened plates of different slenderness
PublicationThe objective of this study is to analyse the behaviour of compressed stiffened plates of different slenderness using experimental and numerical methods. The presented results are part of a long-term project to investigate the ultimate strength of geometrically imperfect structures subjected to different degradation phenomena, including corrosion degradation and locked cracks. Several specimens were subjected to a uniaxial compressive...
-
DETERMINATION OF ADDITIONAL TENSION IN TOWED STREAMER CABLE TRIGGERED BY COLLISION WITH UNDERWATER MOVING OBJECT
PublicationThe paper deals with issues connected with the behaviour of a streamer cable towed by a survey seismic vessel when the cable undergoes a strike triggered by collision with an underwater moving object. The consequences of such collisions may be both threat to the life of marine animals or damage to underwater units and large economic losses suffered by vessel owners. The risk of such collisions has increased over the last years...
-
Modelling reinforced concrete beams under mixed shear-tension failure with different continuous FE approaches
PublicationThe paper presents quasi-static numerical simulations of the behaviour of short reinforced concrete beams without shear reinforcement under mixed shear-tension failure using the FEM and four various constitutive continuum models for concrete. First, an isotropic elasto-plastic model with a Drucker-Prager criterion defined in compression and with a Rankine criterion defined in tension was used. Next, an anisotropic smeared crack...
-
Simulations of hydro-fracking in rock mass at meso-scale using fully coupled DEM/CFD approach
PublicationThe paper deals with two-dimensional (2D) numerical modelling of hydro-fracking (hydraulic fracturing) in rocks at the meso-scale. A numerical model was developed to characterize the properties of fluid-driven fractures in rocks by combining the discrete element method (DEM) with computational fluid dynamics (CFD). The mechanical behaviour of the rock matrix was simulated with DEM and the behaviour of the fracturing fluid flow...
-
Discrete Modelling of Micro-structural Phenomena in Granular Shear Zones
PublicationThe micro-structure evolution in shear zones in cohesionless sand for quasi-static problems was analyzed with a discrete element method (DEM). The passive sand failure for a very rought retaining wall undergoing horizontal translation towards the sand backfill was discussed. To simulate the behaviour of sand, the spherical discrete element model was used with elements in the form of rigid spheres with contacts moments.
-
Sensitivity analysis of simple random beam models by means of Monte Carlo Methods using Variance Reductions Techniques
PublicationA probabilistic sensitivity analysis of two nonlinear bar structures is presented. The analysis is carried out on the basis of the Monte Carlo method. The imperfections of the structures and the applied loads are adapted as random variables. Based on all of the generated input variables, an output response of the system is sought. Afterwards, a coefficient responsible for the structure failure is calculated and the limit state...
-
Simple gait parameterization and 3D animation for anonymous visual monitoring based on augmented reality
PublicationThe article presents a method for video anonymization and replacing real human silhouettes with virtual 3D figures rendered on a screen. Video stream is processed to detect and to track objects, whereas anonymization stage employs animating avatars accordingly to behavior of detected persons. Location, movement speed, direction, and person height are taken into account during animation and rendering phases. This approach requires...
-
Low-energy positron scattering from gas-phase uracil
PublicationQuantum scattering calculations are presented for the interaction of low energy positrons with the uracil molecule, an important component of biological systems. The rotational elastic and inelastic cross sections and vibrational inelastic cross sections are reported and compared with existing experiments, indicating a general trend of the cross sections different from the experimental findings and in line with what should be expected...
-
Failure of cold-formed beam: How does residual stress affect stability?
PublicationIn machine industry, stresses are often calculated using simple linear FEM analysis. Occasional failures of elements designed in such a way require recomputation by means of more sophisticated methods, eg. including plasticity and non-linear effects. It usually leads to investigation of failure causes and improvement of an element in order to prevent its unwanted behavior in the future. The study presents the case where both linear...
-
Mechanical characterization of a gravel column in a calibration chamber operating as a triaxial cell
PublicationA series of tests considering the behavior of gravel columns was performed. A segment of column with a height of 1 m and a diameter of 0.53 m was modelled in a calibration chamber used as a triaxial cell at three different lateral stress applied. The vertical load transferred on the column head was simulated with steady increase of water pressures in the upper and lower membranes. During the loading the volumetric changes in the...
-
High temperature monoclinic-to-tetragonal phase transition in magnesium doped lanthanum ortho-niobate
PublicationMagnesium doped lanthanum ortho-niobate (La0.98Mg0.02NbO4) was prepared by the molten salt synthesis method. X-ray diffraction and dilatometry methods were used to study high temperature behavior of the ceramic material. Special attention was paid to the phase transition between the monoclinic and tetragonal phases. The values of spontaneous strain on the basis of unit cell parameter, obtained by Rietveld refinement, have been...
-
Characterization of Bi6Fe2Ti3O18 Ceramics with Impedance Spectroscopy
PublicationIn the present research the tool of impedance spectroscopy was utilized to characterize dielectric behavior of Aurivillius-type ceramics of Bi6Fe2Ti3O18 composition fabricated by hot pressing method from the stoichiometric mixture of oxides Bi2O3, TiO2 and Fe2O3. Impedance spectroscopy was applied to characterize dielectric response of bulk, grain boundary, and material/electrode interfaces of the fabricated polycrystalline ceramic...