Search
Filters
total: 2251
filtered: 1736
displaying 1000 best results Help
Search results for: TRECE%20ELEMENTS
-
Simulation of large thrust-bearing performance at transient states, warm and cold start-up
PublicationThe start-up of a large hydrodynamic thrust bearing of a vertical hydrogenerator is one of the most critical situations during the lifetime of a bearing. Hydrodynamic load capacity is low due to low speed and higher thermal deformations of the pad. A new approach to the simulation of a hydrodynamic bearing is shown in this article. A combination of finite elements method and computational fluid dynamics is used to perform the transient...
-
The conducted EMI in DC-DC converters
PublicationThis book presents the phenomena of conducted electromagnetic interference (EMI) generation in DC-DC converters. The measurement and simulation are used to analyze the impact of the most important parameters on the character, level and propagation path of interference. In this book, the analysis of the interference generation and propagation is presented on the example of three basic converters. The wide banded behavior of all...
-
Process zone in the Single Cantilever Beam under transverse loading. - Part I: Theoretical analysis
PublicationSingle Cantilever Beam (SCB) specimen loaded with a transverse force parallel to the crack front is proposed for the analysis of crack propagation phenomena under mixed mode conditions. The stress redistribution in the adhesive layer in the vicinity of the crack front so as the beam deformation are estimated using a Timoshenko beam on elastic foundation model. This model emphasizes the Mode II contribution due to flexural beam...
-
Imaging of Increasing Damage in Steel Plates Using Lamb Waves and Ultrasound Computed Tomography
PublicationThis paper concerns inspection of steel plates, with particular emphasis on the assessment of in-creasing damage. Non-destructive tests were performed on four plates, one of which was un-damaged, while the remaining three had a defects in the form of circular holes with a diameter of 2, 5, and 10 cm. Guided Lamb waves were used in the research, and the image reconstruction was performed using ultrasound computed tomography. The...
-
Fracture prediction in flat PMMA notched specimens under tension - effectiveness of the equivalent material concept and fictitious material concept
PublicationThe fracture of notched elements under mode I loading (tension) remains an inexhaustible research topic, especially when it comes to the fracture of thermoplastic materials such as polymethylmethacrylate (PMMA), which experience considerable plastic strains under tension. The paper points out that traditional brittle fracture criteria such as mean stress (MS) or maximum tangential stress (MTS) criteria used to predict this phenomenon do...
-
Improvement of the load capacity of the road overpass as a result of repairs after breakage caused by vehicle impacts
PublicationDamage of spans of the overpass caused by impact of underpassing vehicles are a frequent case. Objects that use prefabricated load-bearing elements that are not designed for such impacts are particularly exposed. After impact, such parts suffer extensive damage that need repair. Taking advantages of this recovery actions it is worth to perform strengthening that will protect object against possible future impacts. In this study...
-
Miniaturization of ESPAR Antenna Using Low-Cost 3D Printing Process
PublicationIn this paper, the miniaturized electronically steerable parasitic array radiator (ESPAR) antenna is presented. The size reduction was obtained by embedding its active and passive elements in polylactic acid (PLA) plastic material commonly used in low-cost 3D printing. The influence of 3D printing process imperfections on the ESPAR antenna design is investigated and a simple yet effective method to compensate them has been proposed....
-
Influence of Dielectric Overlay Permittivity on Size and Performance of Miniaturized ESPAR Antenna
PublicationIn this paper, influence of dielectric overlay permittivity on miniaturized ESPAR antenna parameters is presented. ESPAR antenna is a low-cost and energy-efficient way to implement beam steering capability to a node and improve network performance. The antenna size reduction is obtained by embedding its active and passive elements in ABS based materials of relative permittivity equal to 4, 5.5 and 7.5 in order to achieve network...
-
Special Issue: “Non-Destructive Testing of Structures”
PublicationThe Special Issue “Non-Destructive Testing of Structures” has been proposed to present recent developments in the field of diagnostics of structural materials and components in civil and mechanical engineering. The papers highlighted in this editorial concern various aspects of non-invasive diagnostics, including such topics as condition assessments of civil and mechanical structures and connections of structural elements, the...
-
Increasing the Efficiency of Ontology Alignment by Tracking Changes in Ontology Evolution
PublicationIn this paper we present a development of our ontology alignment framework based on varying semantics of attributes. Emphasising the analysis of explicitly given descriptions of how attributes change meanings they entail while being included within different concepts have been proved useful. Moreover, we claim that it is consistent with the intuitive way how people see the real world and how they find similarities and correspondences...
-
Research on Tool Temperature Dependence on Lapping Grains Size
PublicationCommonly used as a finishing operation, lapping has been used for achieving ultra-high finishes and close tolerances between mating pieces. Its carried out by applying loose abrasive grains between work and lap surfaces, and causing a relative motion between them resulting in a finish of multi-directional lay. The grains activity (sliding and rolling) in the working gap causes not only the material removal but also the temperature...
-
Computationally Efficient Surrogate-Assisted Design of Pyramidal-Shaped 3D Reflectarray Antennas
PublicationReflectarrays (RAs) have been attracting considerable interest in the recent years due to their appealing features, in particular, a possibility of realizing pencil-beam radiation patterns, as in the phased arrays, but without the necessity of incorporating the feeding networks. These characteristics make them attractive solutions, among others, for satellite communications or mobile radar antennas. Notwithstanding, available microstrip...
-
New generation of the satellite hydraulic pumps
PublicationHydraulic satellite machines are known and produced in many versions, recognizable by the number of humps on their inner rotor and external gear, and therefore by the number of cooperating gears (satellites). All known shapes were however designed on the base of preliminary assumption that rotor’s and external gear’s pitch lines are formed by merging arcs, tangent to each other in the. This assumption makes calculations easier,...
-
Dyskretno-ciągła metoda modelowania układów dynamicznych
PublicationW artykule przedstawiono oryginalną metodę modelowania układów dyskretno-ciągłych. Metoda polega na dyskretyzowaniu układu trójwymiarowego jedynie w dwóch wybranych kierunkach. W trzecim z kierunków układ pozostaje ciągły. Otrzymany w ten sposób model jest modelem dyskretno-ciągłym. Opisany jest za pomocą równań różniczkowych cząstkowych. Ogólne równania różnicowe układu dyskretnego otrzymano, wykorzystując metodę sztywnych elementów...
-
Błędy dotyczące kotwienia w budownictwie
PublicationW artykule zwrócono uwagę na typowe błędy w projektowaniu oraz wykonawstwie systemów kotwienia w budownictwie. Omówiono normowe zalecenia dotyczące obliczeń nietypowych elementów. Przedstawiono kilka przykładów błędnego wykonania kotwienia z rzeczywistej realizacji. Skomentowano rodzaj błędów i ich przyczynę.
-
Intra-operative biopsy in chronic sinusitis detects pathogenic Escherichia coli that carry fimG/H, fyuA and agn43 genes coding biofilm formation
PublicationThe aim of this study was to investigate whether or not surgical biopsy of sinus tissue in chronic sinusitis, not responsive to treatment, would detect E. coli. We intended to evaluate E. coli virulence genes, therefore dispute the causal role of such an unusual microorganism in chronic sinusitis, as well as consider effective pathogen-targeted therapy. Patients with E. coli isolated by intra-operative puncture biopsy were included...
-
The effect of road restraint systems on the level of road safety - Polish experience
PublicationRoadside accidents happen when a vehicle runs off the road. The majority of these accidents are very severe because leaving the road is usually followed by hitting a solid obstacle (tree, pole, support, culvert front wall, barrier). Roadsides are some of the most important issues of road safety. They have been studied for years to identify roadside hazards and the effectiveness of road safety measures such as restraint systems....
-
Intelligent Decision Forest Models for Customer Churn Prediction
PublicationCustomer churn is a critical issue impacting enterprises and organizations, particularly in the emerging and highly competitive telecommunications industry. It is important to researchers and industry analysts interested in projecting customer behavior to separate churn from non‐churn consumers. The fundamental incentive is a firm’s intent desire to keep current consumers, along with the exorbitant expense of gaining new ones....
-
Review of Recent Advancement on Nature/Bio-inspired Antenna Designs
PublicationThis article presents an extensive examination of antennas rooted in nature and biology, showcasing their remarkable performance across a wide spectrum of frequencies—from microwave to terahertz. The limitations of traditional antenna design have become increasingly evident in the face of burgeoning demands for novel communication technologies. Conventional analytical-equation-based approaches struggle to deliver the combined performance...
-
Lignocellulosic waste biosorbents infused with deep eutectic solvents for biogas desulfurization
PublicationThis paper introduces an innovative method for treating biogas streams, employing lignocellulosic biosorbents infused with environmentally friendly solvents known as deep eutectic solvents (DES). The primary focus of this study was the elimination of volatile organosulfur compounds (VSCs) from model biogas. Biosorbents, including energetic poplar wood, antipka tree, corncobs, and beech wood, were used, each with varying levels...
-
O zbieżności rozwiązań w nieliniowym mikropolarnym ośrodku sprężysto-plastycznym - zastosowanie elementów skończonych wyższego rzędu.
PublicationEfekty lokalizacji w nieliniowym geometrycznie sprężysto-plastycznym mikropolarnym ośrodku z osłabieniem materiału. Hipotezy Hubera-Misesa-Hencky’ego i Druckera-Pragera. Rozwiązanie równań sprężysto-plastycznych przy użyciu algorytmu powrotnego. Opis zastosowanych elementów skończonych. Przykłady numeryczne obliczeń w geotechnice.
-
Traffic Modeling in IMS-based NGN Networks
PublicationIn the modern world the need for accurate and quickly delivered information is becoming more and more essential. In order to fulfill these requirements, next generation telecommunication networks should be fast introduced and correctly dimensioned. For this reason proper traffic models must be identified, which is the subject of this paper. In the paper standardization of IMS (IP Multimedia Subsystem) concept and IMS-based NGN...
-
The effect of package type on selected parameters of nutritional quality of the chilled stored red sauerkraut
PublicationThe key elements responsible for the quality of food are the technologies used toprocess raw materials and preserve obtained products. The aim of this paper wasto investigate the effect of package type (bags made from low density polyethylene[PE-LD] and the metallized polyethylene terephthalate [PET met/PE foil]) onselected quality parameters of the chilled stored red sauerkraut. Vegetables wereanalyzed before packaging and after...
-
The influence of applying supplementary web plates on structural joint moment resistance and rotational stiffness
PublicationContinual trend to simplify structural elements and find less time-consuming solutions on construction site as well as inevitable increase in labour costs determine for instance elimination of those technological steps that are difficult to automation. Welding additional reinforcements and web stiffeners is a great example of such a step. The method presented in EN 1993-1-8 [8] is a result of long-term studies focused on calculating...
-
NUMERICAL MODELLING AND EXPERIMENTATION OF HISTORICAL CARPENTRY CORNER LOG JOINTS
PublicationThe main purpose of this research is to determine the stress distributions on the contact surfaces between the logs of the historical carpentry corner joints. The additional purpose is to compare the stress distribution for four different boundary conditions in the case of dry and wet pine wood. The paper presents the results of numerical analysis of the shortcorner dovetail connection and the saddle notch corner joint, which are...
-
Finite element modeling of plastic hinges based on ductility demand-capacity method using nonlinear material for dynamic analysis
PublicationThe article discusses modeling plastic hinges in reinforced concrete interme-diate supports using finite elements methods. The ductility demand-capacitymethod was used to determine the geometrical parameters of cross-section plas-ticization zones, their ability to move and rotate, as well as their ductility. Dueto the varied geometry and stiffness of the supports and their nonlinear behav-ior under dynamic load, this method was...
-
Compressible gas density measurement by means of Fourier analysis of interferograms
PublicationThis paper describes a method for nonintrusive compressible gas density measurement by means of automated analysis of interferograms using FFT (Fast Fourier Transform), and its implementation using DFT (Discrete Fourier Transform), that does make this measurement technique a fairly valuable and accessible experimental method. The presented approach makes it possible to use the finite fringe setting of the interferometer, thus reducing...
-
Harmonic Vibrations of Nanosized Magnetoelectric Bodies with Coupled Surface and Interphase Effects: Mathematical Models and Finite Element Approaches
PublicationThe harmonic problems for piezomagnetoelectric nanosized bodies with taking into account the coupled damping and surface effects are considered on the base of the generalized Gurtin-Murdoch model. In the development of previous investigations, the coupled mechanical, electric and magnetic surface effects with surface inertial terms are introduced into the model. For a homogeneous model, the composite material is considered as homogeneous...
-
Stress analysis of a strip under tension with a circular hole
PublicationThe paper addresses stress analysis of a strip with a circular hole under uniform uniaxial tension based oncircumferential stress expressionρπ. Stresses are analyzed in the infinite-length strips under tension with holes, the ratioof the hole radiusa to the strip half-widthb is either equal to:κ =a/b = 0.1 orκ = 0.5. Circumferential stresses aredetermined in selected cross-sections of the strip. The stress diagrams display local...
-
A material model of asphalt mixtures based on Monte Carlo simulations
PublicationThe paper aims to numerically reflect mineral-asphalt mixture structure by a standard FEM software. Laboratory test results are presented due to bending tests of circular notched elements. The result scatter is relatively high. An attempt was made to form a random aggregate distribution in order to obtain various results corresponding to laboratory tests. The material structure calibration, its homogenization and finite element...
-
Hybrid Modulation for Modular Voltage Source Inverters with Coupled Reactors
PublicationThis paper proposes and discusses a concept of a hybrid modulation for the control of modular voltage source inverters with coupled reactors. The use of coupled reactors as the integrating elements leads to significant reduction in the size and weight of the circuit. The proposed modulation combines novel coarsely quantized pulse amplitude modulation (CQ-PAM) and innovative space-vector pulse width modulation (SVPWM). The former...
-
Stanowisko wizualizacji zdarzeń w systemie STRADAR – realizacja i funkcje dla operatora
PublicationIt is crucial for the Border Guard to be equipped with a communication-teleinformatic infrastructure designed to support them in efficient realization of their operational tasks. STRADAR – a system which results are presented in this paper – is such an infrastructure. It is a distributed solution for the maritime division of the border guard. The system, with the use of a network of sensors located in both stationary and mobile...
-
Implementation of constant component filter in measurements of random telegraph signal noise
PublicationNoise is generated in all semiconductor devices. The intensity of these fluctuations depends on used elements, manufacturing process, operating conditions and device type. The result noise is a superposition of different kinds of fluctuations like thermal noise, generation-recombination noise, 1/f noise, shot noise and Random Telegraph Signal (RTS) noise. The last one, RTS noise is observed as nonstationary impulse fluctuations....
-
Revision of Biological Methods for Determination of EDC Presence and Their Endocrine Potential
PublicationEndocrine-disrupting compounds (EDC) are chemicals responsible for disturbances in the hormonal balance of organisms. This group of chemicals includes both egzogenic and endogenic substances or their mixtures that impact functioning of natural hormones in organisms. In the available literature one can find information on the application of chromatographic and related techniques in the analysis of environmental samples for detection,...
-
Wybrane aspekty modelowania matematycznego kolejowego odbieraka prądu
PublicationNieprawidłowa współpraca odbieraka z siecią jezdną, w niekorzystnych warunkach lokalnych, prowadzi do uszkodzeń sieci lub odbieraka. Może być to spowodowane niewłaściwym wykonaniem lub utrzymaniem tych istotnych elementów układu zasilania. Tego typu sytuacje awaryjne powodują duże opóźnienia w ruchu pociągów i generują olbrzymie koszty. Wskazuje to na duże znaczenie odpowiednich rozwiązań konstrukcyjnych sieci i odbieraków oraz...
-
Modeling and analysis of the effectiveness of the guard systemswith dynamic graphs
PublicationIn the following paper it will be presented a new model for analysis (in polynomial time) of the effectiveness of the guard systems. Therewill be presented its practical applications in problems such as searching for the weakest points of the system, planning guards' paths or cameras deployment, switching image from multiple cameras on several monitors, or interception of the intruder. This model is based on describing the guarded...
-
Water uptake and energetics of the formation of barium zirconate based multicomponent oxides
PublicationA group of multi-component oxides based on BaZrO3 have been prepared using a solid-state reaction method and examined in terms of their water uptake and thermodynamics of formation. Depending on the type and amount of acceptor substitution, the synthesized compounds exhibit various proton defect concentrations, reaching up to 0.2 mol/mol for a compound containing 10 different elements in the B-sublattice, where 50% of them are...
-
HYDROACOUSTIC NOISE MEASUREMENTS
PublicationThe paper deals mainly with investigation of underwater noise that propagation is in shallow water. In this paper has been presented the experimental investigation results concerning the distribution of the sound field pressure generated by moving ships in the shallow water at the small distance from the ship. The main acoustical characteristics describing features of the field are spectrograms in pseudo 3D system – distance and frequency...
-
2015. Motion analysis of a kitesurfer employing a vision-based measurement system
PublicationAbstract. Kitesurfing is a relatively new phenomenon with rising popularity worldwide – a recently developed extreme watersport considered a high-risk injury sport. It combines elements of several other sports, in particular, sailing, surfing, windsurfing, wakeboarding, and snowboarding. The main purpose of authors’ research in the present paper is to use a vision-based system for measuring a kitesurfer’s body movements in order...
-
Preliminary experimental research on stability of truss' joint with positive eccentricity
PublicationRecently, a very large interest in lightweight steel structures made from cold-formed sections has been noticeable. In the design practice, a large emphasis is put on rational shaping of both the thin-walled elements and constructions designed on them. The aim of this paper is to present the methodology for preparation of experimental research that model the behaviour of members in trusses made of cold-formed sections with positive...
-
EXPERIMENTAL AND NUMERICAL STUDY ON COLLISIONS BETWEEN STEEL STRUCTURES UNDER EARTHQUAKE EXCITATION
PublicationIn the time of high urbanization, the need to build closely-spaced structures forces the designers to take into account earthquake-induced collisions between adjacent buildings and their effects on the response of structures. Past and recent investigations confirmed that interactions between adjacent buildings during earthquakes may cause serious damages to the structural elements and may even lead to total collapse of the structure....
-
Distribution of the displacement sequence of an orientation preserving circle homeomorphism
PublicationIn some applications not only the knowledge of the behaviour of trajectories of a map is important, but also their displacements. We describe in detail the distribution of elements of the displacement sequence along a trajectory of an orientation preserving circle homeomorphism ϕ with irrational rotation number ϱ(ϕ). The values of displacement are dense in a set which depends on the map γ (semi-)conjugating ϕ with the rotation...
-
Study of Noise Propagation for Small Vessels
PublicationThe paper presents the results of the noise propagation analysis in ship structures tested in a number of AHTS (Anchor Handling Tug Supply) vessels. Statistical Energy Analysis (SEA) based on numerical model developed specially for the purpose of this numerical investigation were conducted. This numerical model enabled the analysis of both the structural elements and the acoustic spaces. For the detailed studies 47 points fixed...
-
THE INFLUENCE OF GESTALT THEORY ON ERNST CASSIRER’S PHENOMENOLOGY OF SYMBOLIC FORMS
PublicationIn the opinion of many scholars the notion of symbolic pregnancy is one of the key concepts in Ernst Cassirer’s philosophy of symbolic forms. Without a proper under-standing of its conceptual frame Cassirer’s philosophy lacks a consistent foundation. The notion symbolic pregnancy offers the mechanism of distinction of symbolic forms. The newest investigations (also in unpublished or less known, neglected writings of the philosopher)...
-
Acceleration of the DGF-FDTD method on GPU using the CUDA technology
PublicationWe present a parallel implementation of the discrete Green's function formulation of the finite-difference time-domain (DGF-FDTD) method on a graphics processing unit (GPU). The compute unified device architecture (CUDA) parallel computing platform is applied in the developed implementation. For the sake of example, arrays of Yagi-Uda antennas were simulated with the use of DGF-FDTD on GPU. The efficiency of parallel computations...
-
Influence of pitting corrosion on fatigue and corrosion fatigue of ship and offshore structures. Part II: Load - pit crack interaction
PublicationIn the paper has been discussed influence of stresses on general corrosion rate and corrosion pit nucleation and growth rate, whose presence has been questioned by some authors but accepted by most of them. Influence of pit walls roughness on fatigue life of a plate suffering pit corrosion and presence of so called "non damaging" pits which never lead to initiation of fatigue crack, has been presented. Possibility of prediction...
-
Numerical Analysis of TB32 Crash Tests for 4-cable Guardrail Barrier System Installed on the Horizontal Convex Curves of Road
PublicationHorizontal curves are one of the elements of road infrastructure where statistically a relatively high number of accidents have been reported. In the last ten years in Poland approx. 10% of all road accidents happened on horizontal curves of roads and was responsible for approx. 14% of all fatalities on Polish roads. Thus, this issue is important and requires extensive research and proper road safety treatments. One possible measure...
-
The Effects of Roadside Hazards on Road Accident Severity
PublicationThe risk of becoming involved in an accident emerges when elements of the transport system do not operate properly (man – vehicle – road – roadside). The road, its traffic layout andsafety equipment have a critical impact on road user safety. This gives infrastructural work a priority in road safety strategies and programmes. Run-off-road accidents continue to be one of the biggest problems of road safety with consequences including...
-
Property revenues (PRs) and expenditures of local government units (LGUs) in Poland
PublicationPRs are new category of local government revenues, which was introduced by changing the law on public finances at the end of 2006 and which took effect in 2007. By principle, these revenues should be converted into property expenditures. Their formalisation did not only allow assessing their absolute size but also a comparison with the longer existing property expenditures. Both categories were subject of analysis in this article....
-
Ontologies vs. Rules — Comparison of Methods of Knowledge Representation Based on the Example of IT Services Management
PublicationThis text provides a brief overview of selected structures aimed at knowledge representation in the form of ontologies based on description logic and aims at comparing them with their counterparts based on the rule-based approach. Due to the limitations on the length of the article, only elements associated with the representation of concepts could be shown, without including roles. The formalisms of the OWL language were used...