Filters
total: 199
filtered: 186
Search results for: propeller ventilation
-
Analiza możliwości zastosowania środowiska SCILAB do wspomagania projektowania podsystemów energetycznych statków = Analysis of capability of using SCILAB for adding design of power ship subsystems
PublicationW artykule przedstawiono koncepcję wykorzystania środowiska symulacyjnego Scilab, modeli matematycznych oraz badań symulacyjnych przy projektowaniu podsystemów energetycznych statku. Zredagowano przykładową strukturę zawierającą model wysokoprężnego silnika oraz model śruby okrętowej. Przedstawione procedury oraz modele matematyczne zostaną włączone do systemu ekspertowego wspomagającego projektowanie statków. This paper deals...
-
Manoeuvring forces on azimuthing podded propulsor model
PublicationThis paper presents the preliminary part of comprehensive manoeuvring open- water tests of a gas carrier model. The paper focuses on open water experiments with an azimuthing podded propulsor. The test program was carried out in the cavitation tunnel and the large towing tank of Ship Hydromechanics Division, Ship Design and Research Centre, Gdańsk. The pod was tested as a pushing unit with a 161.3 mm diameter propeller. Steering...
-
On the Possibility of Increasing Ship Energy Efficiency Through Improved Propulsion Control System
PublicationThis paper summarizes the analyses conducted to assess the impact of the ship's propulsion control system on energy efficiency in calm, manoeuvre, and sea wave conditions, where the goal of the investigation is to develop new strategies for controlling the ship's motion while considering the interactions between the hull, engine, and propeller.
-
Features of load and wear of main propulsion devices on sea-going ships with piston combustion engines and their impact on changes in technical states of the systems
PublicationThe paper presents the specificity of operation of propulsion systems of seagoing ships which causes the need to control the load on them, especially on their engines called main engines. The characteristics of the load on the propulsion systems, especially on the main engines as well as on the shaft lines and propellers driven by the engines, along with the process of wear in tribological joints (sliding tribological systems)...
-
Influence of external walls' thermal capacitance on indoor thermal comfort
PublicationThe doctoral thesis presents the results of numerical investigations on the influence of walls’ thermal capacitance on indoor thermal comfort. A proper set of thermal parameters of a building structure can considerably limit the heating / cooling demand, and passively increase the indoor thermal comfort. However the effect of building thermal capacitance on indoor conditions is complex and not always beneficial. Among a great number...
-
PHYSICAL MODEL OF ENERGY-RELATED PROCESSES IN A ROTATING MECHANICAL SYSTEM FOR THE PURPOSES OF DIAGNOSIS OF TRANSMISSION SHAFTS
PublicationIn the present article, selected problems connected with identification of slowly changing energy-related processes accompanying high cyclic fatigue of construction materials of simple mechanical systems, with special consideration of transmission shafts, are mentioned for diagnostic purposes. The article also presents physical models of object and processes that in a simplified way reflect mechanical energy transmission from transmission...
-
Investigating Fuel Injection Strategies to Enhance Ship Energy Efficiency in Wave Conditions
PublicationThe prediction of fuel consumption and resulting transportation costs is a crucial stage in ship design, particularly for conditions involving motion in waves. This study investigates the real-time fuel consumption of a container ship when sailing in waves. The overall ship performance is evaluated using a novel non-linear coupled hull-engine-propeller interaction model. A series of towing tank experiments for hull resistance in...
-
Coupling between Blood Pressure and Subarachnoid Space Width Oscillations during Slow Breathing
PublicationThe precise mechanisms connecting the cardiovascular system and the cerebrospinal fluid (CSF) are not well understood in detail. This paper investigates the couplings between the cardiac and respiratory components, as extracted from blood pressure (BP) signals and oscillations of the subarachnoid space width (SAS), collected during slow ventilation and ventilation against inspiration resistance. The experiment was performed on...
-
The application of magnetic fluids in sealing nodes designed for operation in difficult conditions and in machines used in sea environment
PublicationPresented in article MF seals are being researched for sea technology purposes due to their excellenttightness and low resistance of motion. These features are most valuable for ring propellers and ship'smain propeller shaft. There are more reasons why technologists payf significant attention for various MFseals applications in their difficult operating conditions. For instance, an advanced pumping systemsare designed with contactless...
-
The application of magnetic fluids in sealing nodes designed for operation in difficult conditions and in machines used in sea environment
PublicationPresented in article MF seals are being researched for sea technology purposes due to their excellent tightness and low resistance of motion. These features are most valuable for ring propellers and ship's main propeller shaft. There are more reasons why technologists payf significant attention for various MFseals applications in their difficult operating conditions. For instance, an advanced pumping systems are designed with contactless...
-
Air flow phenomena in the model of the blind drift
PublicationIn the presented paper, Particle Image Velocimetry (PIV) has been used to investigate flow pattern and turbulent structure in the model of blind drift. The presented model exist in mining, and has been analyzed to resolve ventilation issues. Blind region is particularly susceptible to unsafe methane accumulation. The measurement system allows us to evaluate all components of the velocity vector in channel cross-section simultaneously....
-
Efficiency of Biomass Energy used for Heating Purposes in a Residential Building in Comparison with other Energy Sources
PublicationThis paper discusses the results of analyses investigating the energy efficiency of biomass in comparison with other popular energy carriers used for heating, ventilation and water heating in residential buildings. The compared energy sources were lignite, natural gas, heating oil and electricity produced by conventional and integrated power generation plants. The most efficient variant relying on biomass and the least efficient...
-
A framework for Air Quality Management Zones - Useful GIS-based tool for urban planning: Case studies in Antwerp and Gdańsk
PublicationThere is a growing recognition of the importance of proper urban design in the improvement of air flow and pollution dispersion and in reducing human exposure to air pollution. However, a limited number of studies have been published so far focusing on the development of standard procedures which could be applied by urban planners to effectively evaluate urban conditions with respect to air quality. To fill this gap, a new approach...
-
Rational Use of Primary Energy in Single-Family Residential Houses
PublicationThis work presents results of the primary energy use for heating residential single-family house. Analysis includes domestic hot water system (DHW) and heating, ventilation and air condition system (HVAC). During researches the conventional and alternative energy sources (natural gas, biomass, fuel oil, bituminous coal, lignite or electric energy obtained from electric power system – EPS) were used in DHW and HVAC systems. Furthermore...
-
Turbomachinery - Background
PublicationThe "Turbomachinery - Background" is the first part of a series of monographs devoted to different aspects of rotating machines. The book presents the main fundamentals which are necessary for the different problems of steam, gas, wind and water turbines as well as pumps, compressors and propellers which will discussed in detail in the subsequent parts of the series.
-
Comparison of selected parametric methods for prediction of inland waterways ship hull resistance in towing tank test
PublicationIn the paper selected approximate methods for calculation of inland waterways ship resistance and their verification by towing tests, compared on the example of a small urban ferry, are presented. The test results are made for both the bare hull and the hull with appendages (skeg, azimuthal propeller). Significant differences between results of the theoretical methods and experimental ones, especially in the case of the model with...
-
Reducing Air Pollutant Emissions from the Residential Sector by Switching to Alternative Energy Sources in Single-Family Homes
PublicationThe paper discusses a scenario for adapting residential buildings to the requirements of the EU climate and energy package. It analyzes the option of reducing pollutant emissions to ambient air by switching to alternative energy sources in a typical single-family residential building. The most common sources of energy in central heating and ventilation systems and water heating systems were compared, and the analyzed energy carriers...
-
Model obliczania kosztu cyklu życia obiektu na przykładzie budynku mieszkalnego jednorodzinnego
PublicationW artykule przedstawiono model obliczania kosztu cyklu życia budynku mieszkalnego jednorodzinnego oraz wskazano możliwości ograniczenia wydatków związanych z jego użytkowaniem w okresie trzydziestu lat. Celem prezentowanej analizy rachunku kosztu cyklu życia jest porównanie i ocena kosztów nabycia i użytkowania domu realizowanego według alternatywnych technologii z uwzględnieniem przyjętych rozwiązań w zakresie pozyskania energii,...
-
Equivalent standard manoeuvres for pod-driven ships
PublicationProcedures for carrying out the manoeuvring tests presented in International Maritime Organisation (IMO) resolution MSC.137(76) are based on the capabilities of ships with conventional steering-propulsion systems. Therefore they do not correspond to ships with other steering-propulsion devices, like pod drives. IMO is aware of this shortcoming and for ships with non-conventional steering and propulsion system may permit the use...
-
Computational Fluid Dynamic study on the wind characteristics of a multifunctional building system model in developed coastal cities
PublicationThis paper presents an approach for providing innovative technology by applying fluid mechanics to the field of architectural design. The aim is to make a building’s shape profitable and strengthen environmental protection by using the wind force to create an integrated wind absorption definition for a multifunctional building system model. Furthermore, taking control of the wind flow over an object can have an impact on not only...
-
Towards a reliable method for extrapolation of propulsion performance for vessels with twin-crp-pod system
PublicationThe study presents power performance prediction of an Ultra Large Container Ship (ULCS) with hybrid twin-crp-pod propulsion system. Twin crp-pod propulsion system is a combination of three concepts: twin screw, contra-rotating propellers (crp) and conventional shaft propellers with pod propulsors behind. The presented study shows the current extrapolation method for crp propulsion systems and tries to point out its weaknesses....
-
Spatial aspects of urban air quality management: Estimating the impact of micro-scale urban form on pollution dispersion
PublicationUrban planning and design solutions affect urban ventilation conditions, thus mitigating the effects of atmospheric pollution. However, these findings are not being implemented in the planning practice to a sufficient extent, partly due to the lack of specific guidelines. Moreover, many urban air quality monitoring (AQM) sites have low represnentativeness and thus do not provide comprehensive data for effective urban air pollution control...
-
Tubular House - Form Follows Technology, Concrete Shell Structure with Inner Thermal Insulation
PublicationThe aim of this paper is the theoretical analysis of the possibilities and limitations of using an unconventional technology and the original architectural form stemming from it – the building with external construction and internal insulation. In Central European climatic conditions, the traditional solution for the walls of heated buildings relies on using external thermal insulation. This stems from building physics: it prevents...
-
HEAT TRANSFER CHARACTERISTICS OF ENHANCED SHELL AND COIL HEAT EXCHANGER
PublicationIn the paper authors presented their own constructions of shell and tube heat exchangers with intensified heat transfer. The shell and coils heat exchangers are in common use in heat ventilations and air conditioning systems. Those types of recuperators are quite simple constructions, the low value of pressure drops and good conditions of heat transfer. The present study shows an experimental investigation of the heat transfer...
-
Experimental research on water lubricated marine stern tube bearings in conditions of improper lubrication and cooling causing rapid bush wear
PublicationWater lubricated bearings are popular in sliding bearings of marine propeller shafts, turbines and pump shafts. Such popularity is partly due to their simple construction which also means a relatively affordable price. In practical experience one may also observe cases of rapid wear or even malfunctions of this bearings, some of which may be caused by insufficient flow of lubricant leading to overheating. The conducted...
-
Low-Cost Flight Simulator with Possibility of Modeling of Flight Controls Failures
PublicationThe goal of this paper is to present a development of a low cost flight simulator, that allows to simulate flight controls failures. Cessna 172 has been chosen as an example of a general aviation aircraft and the flight model has been implemented in Simulink. The model allows for easy integration of an experimental autopilot, using various strategies. Aerodynamic coefficients have been calculated using software called DATCOM. Such...
-
Indoor air quality in public utility environments-a review
PublicationIndoor air quality has been the object of interest for scientists and specialists from the fields of science such as chemistry, medicine and ventilation system design. This results from a considerable number of potential factors, which may influence the quality of the broadly understood indoor air in a negative way. Poor quality of indoor air in various types of public utility buildings may significantly affect an increase in the...
-
Three-dimensional printed trachea helps to design tailored treatment for tracheobronchomalacia
PublicationTracheobronchomalacia is a rare respiratory disease that is manifesting by impaired ventilation with expiratory collapse of the tracheal wall due to softening of the supporting cartilage and hypotonia of myoelastic elements [1]. Surgery is the mainstay of treatment. We report the case of 39 -year old man with exacerbation of chronic respiratory distress. The membranous wall of the trachea and the large bronchi was stretched to...
-
Experimental tests for the determination of mechanical properties of PVC foil
PublicationThe paper presents an application of the PVC film in civil engineering. Mechanical behaviour of the PVC film applied for suspended ceilings, in the form of a stretch ceiling is investigated under uniaxial and biaxial tensile tests. The study is focused on the determination of mechanical properties from experimental data (uniaxial and biaxial tensile tests). The uniaxial cyclic tests are performed in order to observe a variation...
-
Multi-source-supplied parallel hybrid propulsion of the inland passenger ship STA.H. Research work on energy efficiency of a hybrid propulsion system operating in the electric motor drive mode
PublicationIn the Faculty of Ocean Engineering and Ship Technology, Gdansk University of Technology, design has recently been developed of a small inland ship with hybrid propulsion and supply system. The ship will be propelled by a specially designed so called parallel hybrid propulsion system. The work was aimed at carrying out the energy efficiency analysis of a hybrid propulsion system operating in the electric motor drive mode and at...
-
HYDROACOUSTIC NOISE MEASUREMENTS
PublicationThe paper deals mainly with investigation of underwater noise that propagation is in shallow water. In this paper has been presented the experimental investigation results concerning the distribution of the sound field pressure generated by moving ships in the shallow water at the small distance from the ship. The main acoustical characteristics describing features of the field are spectrograms in pseudo 3D system – distance and frequency...
-
An application for a new type of pneumatic engine concept
PublicationHeavy trucks are often equipped with loading and unloading systems like dock levellers with swing lip or telescopic lip. Most of these devices require hydro-electrical energy supply systems (eg. the pump that presses the working substance to the actuators must be propelled by electric engine.) The space taken by pump with electric engine can be reduced on condition that a new type of pneumatic drive will be considered. It is possible...
-
Synergistic effects of a swirl generator and MXene/ water nanofluids used in a heat exchanger pipe of a negative CO2 emission gas power plant
Publicationfocus on optimizing heat exchangers contributes to improved temperature control mechanisms, ensuring the sustainable operation of innovative power plants working towards negative CO2 emissions. In the realm of oxy-combustion within Negative CO2 Emission Power Plants (nCO2PP), the temperature of combustion products surpasses 3000 (K). Addressing this challenge, the imperative arises to reduce these elevated temperatures to a manageable...
-
Importance of model tests in design and operation of watercraft for example CTO
PublicationShip Hydromechanics Division is a specialized research and development department of Ship Design and Research Centre conducting tests and research in the field of hydromechanics, connected with design and operation of ships and other floating structures, in scope of: predictions, numerical analyses, designs of - hull shape optimized with respect to the ship’s functions with the application of modern design tools, screw propellers...
-
Dynamic Positioning Capability Assessment for Ship Design Purposes
PublicationThe article focuses on solving a problem of optimal thrust distribution over the actuators in a ship Dynamic Positioning, according to DNV-ST-0111 standard, Level 1. The classic Quadratic Programming approach is combined with the numerical solusion used to handle the propeller with the rudder constraints in the optimization task and the influence between thrusters and skeg. It is presented as an efficient method of minimizing the...
-
Experimental study on the selected aspects of bow thruster generated flow field at ship zero-speed conditions
PublicationThe paper presents the results of experimental study on the interaction between the bow thrusters understood as the flow field changes generated by bow tunnel thruster in deep water conditions operated as a single and twin units. The research was limited to zero-speed case for the ship dead in the water. The influence of the hull form and jet spread between the neighbouring thrusters for several combinations of the applied bow...
-
Experimental research on marine oil-lubricated stern tube bearing
PublicationBearings of propeller shafts are very crucial elements of the propulsion system of each of the ships. The safety of shipping depends on their durability and reliability. The new legal restrictions mean that today we are looking for environmentally friendly solutions. That is why water-lubricated bearings are becoming more and more popular. So, will oil-lubricated shaft bearings belong to the past? The bearing with a white metal...
-
Agricultural products' storage control system
PublicationThe paper discusses the idea and the design of a remote control system for storage management of agricultural products which temperature may rise as the result of biological processes during the storage. An actual potatoes storehouse is discussed as an application for the proposed automation system. Because of existing buildings and infrastructure at the farm, wireless data transfer system has been proposed for communication between...
-
COMBINING FUNCTIONAL AND AESTHETIC ASPECTS OF DAYLIGHTING IN SUSTAINABLE ARCHITECTURE WITH THE USE OF DIGITAL DESIGN METHODS
PublicationThe aesthetics of modern architecture should relate to its origins and goals - the environment, function, sustainability and its users. One of the conditions that meet the criteria is the presence of daylight and the use of its potential. The contemporary digital tools that support the design process allow to controlling the use of difficult and capricious materials, such as daylight. They also combine daylighting aspects with...
-
Sposoby zagospodarowania ciepła odpadowego z silników napędowych jednostek pływających Cześć 1. Wykorzystanie ciepła do napędu urządzeń chłodniczych
PublicationEnergia chemiczna paliwa jest w wielu przypadkach zaledwie w połowie wykorzystana jako energia napędowa silnika. Pozostała część jako ciepło odpadowe przekazywana jest do otoczenia. Dzięki odpowiednim układom przetwarzania ciepło ze spalin można wykorzystać do wytwarzania chłodu lub jako ciepło użytkowe, w systemach HVAC (ang. heating, ventilation, air conditioning – ogrzewanie, wentylacja, klimatyzacja). Tym samym koszty pracy...
-
Gdansk Bay sea bed sounding and classification of its results
PublicationThe main goal of this paper is to describe the results of sounding the Gdansk Bay sea bed by using a SES-2000 Standard parametric sub-bottom profiler. Quality of data obtained during trials depends inter alia on a proper location of transducer array to reduce influence of pitch, roll and heave motions as well as ship self noise (resulting from bubbles due to propeller and flow around hull, vibration generated by main engine and...
-
NEW DESIGNS OF CENTRIFUGAL MAGNETIC FLUID SEALS FOR ROTATING SHAFTS IN MARINE TECHNOLOGY
PublicationThe centrifugal magnetic fluid seals have important advantage over the conventional centrifugal seals. They maintain very good sealing capacity at static, medium and high speeds of shaft rotation, with the increased seal lifetime, and minimum torque and static friction. These seals are particularly useful in cases when the angular shaft velocity varies and sometimes decreases to nearly or exactly zero, such as in flywheel applications,...
-
Wind Conditions at Pedestrian Level in Different Types of Residential Urban Development for a High Degree of Land Use Efficiency
PublicationThe paper concerns wind conditions around urban building development at the pedestrian level. The article aims to identify aerodynamic phenomena around three types of multi-family housing developmentswith different forms and the same urban parameters of building development intensity (high intensity was taken into account). The aim of the research was mainly to achieve qualitative results that would lead to understanding fundamental...
-
Application of TMS320c67xx signal processors for SONIC-self-optimizing narrowband interference canceler
PublicationThe paper presents a laboratory system for testing active control algorithms of acoustics noise in ducts. An applied algorithm - self-optimizing narrowband interference canceller (SONIC), allows one to remove narrowband disturbances of constant or slowly time-varying frequencies. Example experimental results of using the laboratory system for supression of sinusoidal disturbance are described. An electronic part of the system was...
-
Effect of microstructure on mechanical properties of BA1055 bronze castings
PublicationThe article presents research results performed on aluminum bronze CuAl10Fe5Ni5 (BA1032) castings used for marine propellers. Metallographic studies were made on light microscope and a scanning electron microscope to assess quantitatively and qualitatively the alloy microstructure. It has been shown that the shape, size and distribution of the iron-rich phase precipitates in bronze microstructure significantly affect its mechanical...
-
Application of Shape Memory Alloys in Pipeline Couplings for Shipbuilding
PublicationThe aim of the study is to analyse shape memory alloy (SMA) pipeline joints in limited space applications for all kinds of ships. Generally, the space available in various areas on ships is strictly limited and service works usually meet many obstacles. If we consider a pipeline, the flange joints always require a larger free space around the pipe than the pipe alone. A simultaneous problem can occur with the propeller shaft line...
-
Numerical analysis of the container vessel's self-propulsion at different rudder deflection angles
PublicationNowadays, CFD becomes one of the most commonly used research method in ship hydrodynamics, limited to the analyses of hull resistance in calm water. With continuously improving computing power and increasingly more accurate numerical methods it is possible to simulate more complex cases. State of the art CFD tools also enable development of new ways of assessing ship maneuvering performance. This paper presents an attempt on...
-
Numerical analysis of the container vessel's self-propulsion at different rudder deflection angles
PublicationNowadays, CFD becomes one of the most commonly used research method in ship hydrodynamics, limited to the analyses of hull resistance in calm water. With continuously improving computing power and increasingly more accurate numerical methods it is possible to simulate more complex cases. State of the art CFD tools also enable development of new ways of assessing ship maneuvering performance. This paper presents an attempt on using...
-
Areas of Fan Research—A Review of the Literature in Terms of Improving Operating Efficiency and Reducing Noise Emissions
PublicationFans as industrial devices are among the most significant single recipients of driving energy. Therefore, they represent an important area of energy savings to reduce CO2 emissions. The ubiquity of fans and their operation under conditions different from the optimum provides an opportunity for more significant global reductions in the energy used to drive them. The second important aspect, besides energy efficiency, related to...
-
Will NILM Technology Replace Multi-Meter Telemetry Systems for Monitoring Electricity Consumption?
PublicationThe estimation of electric power utilization, its baseload, and its heating, light, ventilation, and air-conditioning (HVAC) power component, which represents a very large portion of electricity usage in commercial facilities, are important for energy consumption controls and planning. Non-intrusive load monitoring (NILM) is the analytical method used to monitor the energy and disaggregate total electrical usage into appliance-related...