Filters
total: 2745
displaying 1000 best results Help
Search results for: GINI COEFFICIENT
-
Optimising approach to designing kernel PCA model for diagnosis purposes with and without a priori known data reflecting faulty states
PublicationFault detection plays an important role in advanced control of complex dynamic systems since precise information about system condition enables efficient control. Data driven methods of fault detection give the chance to monitor the plant state purely based on gathered measurements. However, they especially nonlinear, still suffer from a lack of efficient and effective learning methods. In this paper we propose the two stages learning...
-
Hybrid battery based on arylated carbon nanotubes and laccase
PublicationSingle-walled carbon nanotubes (SWCNT) were covalently modified with anthracene and anthraquinone and used for the construction of cathodes for biocatalytic reduction of dioxygen. The nanotubes with aromatic groups casted onto the electrode increased the working surface of the electrode and enabled efficient direct electron transfer (DET) between the enzyme and the electrode. The aryl groups enter the hydrophobic pocket of the...
-
On DoA estimation for rotating arrays using stochastic maximum likelihood approach
PublicationThe flexibility needed to construct DoA estimators that can be used with rotating arrays subject to rapid variations of the signal frequency is offered by the stochastic maximum likelihood approach. Using a combination of analytic methods and Monte Carlo simulations, we show that for low and moderate source correlations the stochastic maximum likelihood estimator that assumes noncorrelated sources has accuracy comparable to the...
-
Probability distribution of flicker noise in AuNPdecorated graphene–Si Schottky barrier diode
PublicationWe present results of the probability distribution analysis of flicker noise generated in Au nanoparticle (AuNP) decorated graphene–Si Schottky barrier diodes with and without yellow light illumination (592 nm), close to the localized surface plasmon resonance in the AuNPs (586 nm). The AuNPs occupy imperfections in the single-layer graphene and reduce the flicker noise intensity generated in the graphene layer. The estimated probability...
-
System Loss Model for Body-to-Body Networks in Indoor and Outdoor Environments
PublicationA system loss model for body-to-body networks in indoor and outdoor environments is proposed in this paper, based on measurements taken at 2.45 GHz. The influence of the type of environment, antenna visibility and user mobility on model parameters has been investigated. A significant impact of mutual antennas’ placement and their visibility is shown. The proposed model fits well to empirical data, with the average root mean square...
-
Experimental investigation of forced convection of water/EGAl2O3 nanofluids inside horizontal tube
PublicationIn this paper, forced convection of water/EG-Al2O3 nanofluids inside horizontal stainless steel tube is studied experimentally. As base fluid served water/EG mixture of two ratios (60:50 and 50:50). Nanoparticle mass concentrations was 0.1% or and 1%. Transition and turbulent flow regimes were tested. Average heat transfer coefficient and pressure drop values were determined for nanofluids and compared to base fluids. Deterioration...
-
Numerical investigation on the performance of a small counter-rotating wind turbine
PublicationThe article presents the results of the investigation on the performance of a small counter-rotating wind turbine. The wind turbine has been simulated using Computational Fluid Dynamics methods. Actuator Line Model has been successfully used to represent rotors in the computational domain. A parametric study has been carried out, taking into account changes in the tip speed ratio of the rotors while maintaining a constant distance...
-
Short-range order structure and free volume distribution in liquid bismuth: X-ray diffraction and computer simulations studies
PublicationThe structure of liquid bismuth was studied by X-ray diffraction and computer simulation methods. The contraction of the atomic structure within the first coordination sphere in the temperature interval of 575- 1225 K is reported. The temperature dependencies of the coordination numbers and of the free volume are analysed. On the basis of the temperature dependencies of the free volume, the temperature dependencies of viscosity...
-
Label‐free optical detection of cyclosporine in biological fluids
PublicationIn this paper, a spectroscopic method for determination of cyclosporine concentrations in biological fluids is presented. Blood plasma and hemoglobin solutions are chosen for the experiment. For various cyclosporine concentrations in blood plasma and hemoglobin, absorbance measurements in spectra range from 600 to 1100 nm are performed. The measurement results are analyzed by the use of a dedicated algorithm. The obtained data...
-
Magnetic properties of ferromagnetic Pu2Pt3Si5
PublicationThe structural, magnetic, and thermodynamic properties of a new plutonium based compound, Pu2Pt3Si5, are reported. Single crystals produced by a Sn-flux technique have been analyzed showing a ferromagnetic behavior at 58 K. Pu2Pt3Si5 crystallizes in the U2Co3Si5-type orthorhombic Iabm structure (s.g. 72) with atomic parameters a = 9.9226(2) Å, b = 11.4436(2) Å and c = 6.0148(1) Å. The effective (leff 0.74 lB/Pu) and saturated (rsat...
-
Automated detection of sleep apnea and hypopnea events based on robust airflow envelope tracking
PublicationThe paper presents a new approach to detection of apnea/hypopnea events, in the presence of artifacts and breathing irregularities, from a single-channel airflow record. The proposed algorithm identifies segments of signal affected by a high amplitude modulation corresponding to apnea/hypopnea events. It is shown that a robust airflow envelope—free of breathing artifacts—improves effectiveness of the diagnostic process and allows...
-
HEAT TRANSFER CHARACTERISTICS OF ENHANCED SHELL AND COIL HEAT EXCHANGER
PublicationIn the paper authors presented their own constructions of shell and tube heat exchangers with intensified heat transfer. The shell and coils heat exchangers are in common use in heat ventilations and air conditioning systems. Those types of recuperators are quite simple constructions, the low value of pressure drops and good conditions of heat transfer. The present study shows an experimental investigation of the heat transfer...
-
Numerical analysis of crack propagation in silicone nitride
PublicationThe properties of ceramics, specifically low density, high hardness, high temperature capability and low coefficient of thermal expansion are of most interest to rolling element manufacturers. The influence of ring crack size on rolling contact fatigue failure has been studied using numerical fracture analysis. Such cracks are very often found on ceramic bearing balls and decrease fatigue life rapidly. The numerical calculation...
-
Modification of Selected Propagation Models in Terms of Path Loss Estimation in Container Terminal
PublicationIt is particularly important to look for any propagation model that could be useful for designing mobile radio networks in container terminal environment. Selected propagation models have been investigated. Firstly - basing on measurements results - they have been evaluated in this scope and the analysis has shown, that the adjustment is needed. This modification improved significantly the accuracy of path loss modelling. For the...
-
Metody analizy nośności słupów żelbetowych z uwzględnieniem pełzania betonu
PublicationZgodnie z Eurokodem 2 nośność smukłych słupów żelbetowych można obliczać stosując uproszczone metody uwzględniania efektów II rzędu. W obliczeniach tych słupów istotną rolę odgrywa pełzanie, którego wpływ jest najmniej rozpoznany. W pracy zaproponowano dwa modele numeryczne uwzględniania wpływu pełzania. W pierwszym wpływ pełzania uwzględniono przez modyfikację charakterystyki materiałowej betonu, w drugim zastosowano prawo pełzania...
-
Crystal growth and properties of a binary intermetallic ZrBi2 compound
PublicationSingle crystals of ZrBi2 were grown by a self-flux method. The material adopts TiAs2 structure type with lattice parameters: a = 10.233(4) Å, b = 15.581(2) Å, c = 3.994(5) Å. Crystals of ZrBi2 were studied by means of magnetic susceptiblity, specific heat and resistivity measurements. The compound reveals a metallic-like behavior (RRR = 30). The Sommerfeld coefficient equals γ = 1.59(16) mJ mol-1 K-2 and Debye temperature ΘD =...
-
Harmonic Analysis
Open Research DataWe construct a decomposition of the identity operator on a Riemannian manifold M as a sum of smooth orthogonal projections subordinate to an open cover of M. This extends a decomposition on the real line by smooth orthogonal projection due to Coifman and Meyer (C. R. Acad. Sci. Paris, Sér. I Math., 312(3), 259–261 1991) and Auscher, Weiss, Wickerhauser...
-
Simulation of the switched reluctance drive system
PublicationSwitched reluctance motors (SRM), unlike other types of motors, for their application require a control system and the supply from a power electronic converter. A method of modelling and mathematical model of an SRM in a switched reluctance drive (SRD) system is presented in the paper. Modelling is based on Lagrange's energy method. Coefficients of the Lagrange's equation have been calculated using the finite element method (FEM)....
-
Propagation in the Open Cylindrical Guide of Arbitrary Cross Section With the Use of Field Matching Method
PublicationA simple solution to propagation problem in open waveguides and dielectric fibers of arbitrary convex cross section is presented. The idea of the analysis is based on the direct field matching technique involving the usage of the field projection at the boundary on a fixed set of orthogonal basis functions. A complex root tracing algorithm is utilized to find the propagation coefficients of the investigated guides. Different convex...
-
Sample Rate Conversion Based on Frequency Response Masking Filter
PublicationThe sample rate conversion with high resampling ratios requires low-pass digital filters with very narrow transition band which results in high computational complexity and makes filter design problematic. Therefore in this work we propose to use the FRM method, which breaks the filter with a narrow transition band into a group of filters with reduced design requirements. These decreases the number of non-zero coefficients and...
-
A body position influence on ECG derived respiration
PublicationAn influence of a human body position on ECG derived respiration (EDR) signal is presented in the paper. Examinations were performed during deep, suspended and normal breathing for eight people in four different body positions. EDR and thoracic impedance signals were compared using correlation and standard deviation coefficients. Obtained results have shown that it is possible to monitor breath activity of people being in different...
-
Wybrane elementy projektowania budynków wielofunkcyjnych stanowiących miejskie centra logistyczne
PublicationCelem artykułu jest przedstawienie wybranych aspektów dotyczących projektowania budynków wielofunkcyjnych stanowiących miejskie centra logistyczne. Centrum logistyczne lokalizowane w obszarze zurbanizowanym jest formalnie obiektem, który ma na celu zaspokojenie wielu potrzeb funkcjonalnych względem potencjalnych użytkowników. Miejskie centrum logistyczne stanowi swego rodzaju system, którego podstawą jest sprawna obsługa procesów...
-
Analysis of Position Calculating Methods in Indoor Environment
PublicationIn the paper a modified gradient method has been proposed for position calculation on basis of distance measurement in indoor environment. It is shown that the well-known Chan method of position calculation is inefficient in indoor circumstances. Author presents Chan and modified gradient methods and achieved results for each one for real measurements.
-
Karolina Lademann mgr
PeopleCurriculum vitae
-
Numerical simulation of cold flow and combustion in a swirl stabilized combustor
PublicationA numerical simulation model was developed to investigate the cold flow and combustion using Ansys FLUENT 2021R1. The governing equations were solved using the pressure-based method, and pressure–velocity coupling was performed using the SIMPLE method. To model the turbulent process, the RSM model was used. Non-premixed model is chosen to solve the chemical kinetics between fuel and oxigen. Radiation heat transfer was calculated...
-
INFLUENCE OF THE HULL SHAPE ON THE ENERGY DEMAND OF A SMALL INLAND VESSEL WITH HYBRID PROPULSION
PublicationRecently, there has been a significant development of ecological propulsion systems, which is in line with the general trend of environmentally friendly “green shipping”. The main aim is to build a safe, low-energy passenger ship with a highly efficient, emission-free propulsion system. This can be achieved in a variety of ways. The article presents the main problems encountered by designers and constructors already at the stage...
-
Novel Adaptive Method for Data Streams Allocation Based on the Estimate of Radio Channel Parameters in Heterogeneous WBAN Network
PublicationThe new adaptive method for data streams allocation in heterogeneous Wireless Body Area Networks and meas-urement equipment is presented. The results obtained using the developed method compared with the selected algorithms likely to be used in those networks. The pro-posed adaptive data streams allocation method based on radio channel parameters makes it even twice as efficient to use in terms of resources usage in a WBAN heterogeneous...
-
Analysis of the image force effects on the recombination at the donor-acceptor interface in organic bulk heterojunction solar cells
PublicationWe consider the influence of image force effects on the recombination at the donor-acceptor interface in organic bulk heterojunction solar cells. The conclusion is that the charge carriers of one sign located in the material with lower permittivity recombine at the boundary between donor and acceptor phases. This process competes with the recombination of opposite sign charge carriers, leading to the reduction of the Langevin-type...
-
Speech Intelligibility Measurements in Auditorium
PublicationSpeech intelligibility was measured in Auditorium Novum on Technical University of Gdansk (seating capacity 408, volume 3300 m3). Articulation tests were conducted; STI and Early Decay Time EDT coefficients were measured. Negative noise contribution to speech intelligibility was taken into account. Subjective measurements and objective tests reveal high speech intelligibility at most seats in auditorium. Correlation was found between...
-
Similarity Measures for Face Images: An Experimental Study
PublicationThis work describes experiments aimed at finding a straightforward but effective way of comparing face images.We discuss properties of the basic concepts, such as the Euclidean, cosine and correlation metrics, test the simplest version of elastic templates, and compare these solutions with distances based on texture descriptors (Local Ternary Patterns). The influence of selected image processing methods (e.g. bilateral ltering)...
-
Optimization of clamping stiffness during milling of high-dimensional structures with the use of techniques of experiment – aided virtual prototyping
PublicationThe subject of this paper is a method of searching for conditions of minimizing the vibration level of a tool-high dimensional flexible workpiece, at unchangeable technological parameters of the machining process. It depends on repeatable change of the values of the stiffness coefficients as soon as an optimal vibration state of the workpiece approaches. There are assessed the values of dominant ”peaks” in the frequency spectra...
-
Experimental and theoretical study of flow boiling and dryout phenomenon of ethanol in vertical minitubes
PublicationW ramach przeprowadzonych prac zaadoptowano istniejące stanowisko do badań laminarnej konwekcji wymuszonej, wrzenia w przepływie oraz wysychania filmu cieczy na ściance kanału wykorzystując etanol jako płyn roboczy. Przeprowadzono systematyczne badania wrzenia w przepływie dla dwóch średnic rur, tj. 1.15mm i 2.3mm. W badaniach wykorzystano najnowsze osiągnięcia z zakresu technik termowizyjnych celem znalezienia dokładnej lokalizacji...
-
Underdiagnosis of Major Depressive Episodes in Hemodialysis Patients: The Need for Screening and Patient Education.
PublicationThis article aims to identify the reasons why patients with major depressive episode (MDE) do not seek treatment for their mental disorder. 89 out of 208 persons screened were diagnosed with major depressive episode using the Mini-International Neuropsychiatric Interview. 85 individuals with untreated depression filled out the following questionnaires: Beck Depression Inventory, List of Explanations of Well-Being (LEWB), Brief...
-
Thermal and Hydrodynamic Phenomena in the Stagnation Zone — Impact of the Inlet Turbulence Characteristics on the Numerical Analyses
PublicationOne of the methods of heat transfer enhancement is utilization of the turbulent impinging jets, which were recently applied, for example, in the heat exchangers. Their positive impact on the heat transfer performance was proven, but many questions related to the origin of this impact are still unanswered. In general, the wall-jet interaction and the near-wall turbulence are supposed to be its main reason, but their accurate numerical...
-
Development of a new generation of unmanned surface and underwater vehicles using the advanced technologies and achievements towards the application of control systems by the artificial intelligence AI.
PublicationThe operation of offshore structures at sea requires implementation of the advanced systems of permanent monitoring of work of such the installations. Novel solutions concerning such the systems should be associated with application of unmanned maritime surface and underwater platforms. The unmanned maritime platforms are and will be based on application of the newest achievements of some important technologies. Between these technologies...
-
Bitumen Aging—Laboratory Simulation Methods Used in Practice and Selected Directions of Research on New Methods
PublicationChanges in the properties of bitumen binders that occur as a result of aging have a huge impact on the durability of products produced from them. In particular, asphalt pavements, which constitute the most common use of petroleum bitumen, are susceptible to damage resulting from the increasing stiffness of the bitumen during its life cycle. Increased stiffness of asphalt pavements reduces the pavement resistance to low-temperature...
-
Analiza porównawcza sposobów wyznaczania obciążeń wiatrem na podstawie norm projektowych i analizy przepływu CFD
PublicationW pracy poruszono tematykę wykorzystania analizy przepływu CFD do wyznaczania obciążeń wiatru na konstrukcje. Przedstawiono analizę trzech modeli budynków o dachu dwuspadowym o różnych kątach nachylenia, dla których dokonano porównania wielkości współczynników parcia z wynikami dostępnymi w literaurze. Obliczenia analityczne wykonano zgodnie z normą z PN-EN 1991-1-4, natomiast obliczenia numeryczne wykonano w programie R-Wind Simulation....
-
An improvement of body surface area formulas using the 3D scanning technique
PublicationObjectives: Body surface area (BSA) is one of the major parameters used in several medical fields. However, there are concerns raised about its usefulness, mostly due to the ambiguity of its estimation. Material and Methods: Authors have conducted a voluntary study to investigate BSA distribution and estimation in a group of 179 adult people of various sex, age, and physique. Here, there is provided an extended analysis of the...
-
Improving the CPX method by specifying reference tyres and including corrections for rubber hardnes and temperature
PublicationRecently completed work in the EU project ROSANNE and in working group ISO/TC43/SC1/WG33 has allowed substantial improvements to measurements made by the Close-Proximity (CPX) method, intended for measurement of noise properties of road surfaces.The paper summarizes the experimental work and describes the conclusions and implementation in ISO/FDIS 11819-2 (CPX method) and in the supporting ISO (draft) Technical Specifications 11819-3...
-
Miniaturization of ESPAR Antenna Using Low-Cost 3D Printing Process
PublicationIn this paper, the miniaturized electronically steerable parasitic array radiator (ESPAR) antenna is presented. The size reduction was obtained by embedding its active and passive elements in polylactic acid (PLA) plastic material commonly used in low-cost 3D printing. The influence of 3D printing process imperfections on the ESPAR antenna design is investigated and a simple yet effective method to compensate them has been proposed....
-
The Impact Of The Selected Parameters Of Fdm Manufacturing Technology On Tribological Performance Of Abs–Steel Pair Under Dry Friction
PublicationThe paper presents the result of tribological test of ABS and steel samples sliding under dry friction. Polymeric samples were manufactured of ABS material using FDM technology. Testing was carried out in unidirectional sliding in a ring-on-flat contact in a PT-3 tribometer. The scope of tested parameters included volumetric and mass wear, the friction coefficient, and polymeric specimen temperature. Polymeric specimens used in...
-
Defining the thermal conductivity of thermally heterogeneous hollow wall bricks used as elements for increasing the comfort of buildings
PublicationThe article presents numerical calculation analysis in the scope of determining thermal conductivity coefficientλeq[W/(m·K)] of thermally heterogeneous hollow bricks of thermally heterogeneous structure (a combinationof structural material with thermal insulation material). Numerical calculations were conducted by means ofprofessional software TRISCO-KOBRU 86, serving thermal circulation analysis in a 2D field in stationary approach.The...
-
Calculation method for flow boiling and flow condensation of R134a and R1234yf in conventional and small diameter channels
PublicationThe paper presents the results of calculations performed using the authors’ model to predict the heat transfer coefficient during flow boiling for two refrigerants R134a and R1234yf. The experimental data from various past studies have been collected and the calculations have been conducted for the full range of quality variation and a wide range of mass velocity. The aim of the study was to test the sensitivity of the in-house...
-
Optical-Spectrometry-Based Method for Immunosuppressant Medicine Level Detection in Aqueous Solutions
PublicationIn this paper, an investigation into detecting immunosuppressive medicine in aqueous solutions using a spectrometry-based technique is described. Using optical transmissive spectrometry, absorbance measurements in the spectra range from 250 nm to 1000 nm were carried out for different cyclosporine A (CsA) concentrations in aqueous solutions. The experiment was conducted for samples both with and without interferent substances—glucose...
-
An improved method for flow boiling heat transfer with account of the reduced pressure effect
PublicationIn the paper are presented the results using the authors own model to predict heat transfer coefficient during flow boiling. The model has been tested against a large selection of experimental data to investigate the sensitivity of the in-house developed model. In the work are presented the results of calculations obtained using the semi-empirical model on selected experimental flow boiling data of the refrigerants: R134a, R1234yf,...
-
Examining the Impact of Distance Between VSL Road Signs on Vehicle Speed Variance
PublicationVariable speed limit (VSL) is an intelligent transportation system (ITS) solution for traffic management. The speed limits can be changed dynamically to adapt to traffic conditions such as visibility and traffic volume, curvature, and grip coefficient of the road surface. The VSL traffic sign location problem and attempts to solve it using computer simulation are presented in this paper. Experiments on a selected road segment,...
-
Errors in the analysis of series resonant inverter/converter assuming sinusoidal waveforms of voltage and current
PublicationIn this paper the theory and simulation results of the series resonant inverter / converter are presented. In this work the authors carried out a detailed comparative analysis of results obtained using the method of AC analysis in the steady state for the first harmonic with the results of computer simulation. The AC analysis under certain conditions can lead to errors disqualifying this method. In particular, these errors appear...
-
Temperature Fiber-Optic Sensor with ZnO ALD Coating
PublicationThis study presents a microsphere-based fiber-optic sensor with a ZnO Atomic Layer Deposition (ALD) coating thickness of 100 nm for temperature measurements. Metrological properties of the sensor were investigated over the temperature range of 100 °C to 300 °C, with a 10 °C step. An interferometric signal is used to control whether the microstructure is whole. Spectrum shift of a reflected signal is used to ascertain changes in...
-
Structural properties of hypothetical CeBa2Cu3O7 compound from LSDA+DMFT calculations
PublicationThe hypothetical stoichiometric CeBa2Cu3O7 (Ce123) compound, which has not been synthesized as a single phase yet, was studied by the density functional theory (DFT). We utilized a method which merges the local spin density approximation (LSDA) with the dynamical mean-field theory (DMFT) to account for the electronic correlations. The LSDA+DMFT calculations were performed in the high-temperature range. The particular emphasis was...
-
INVESTIGATION OF JOURNAL SLIDE BEARINGS UNDER THE ANGLE OF THEIR FUNCTIONING
PublicationPaper presents the structure and principle of operation of a stand for measurements of influence of the lubrication method and process on functioning of journal slide bearings in their various technical states. Measurements performed on the stand make it possible to take advantage of the new method of evaluating the influence of physical and chemical properties of lubricating oil on the coefficient of friction in the mixed friction...