Publications
Filters
total: 1509
displaying 1000 best results Help
Catalog Publications
Year 2020
-
Electrophoretic Deposition and Characteristics of Chitosan–Nanosilver Composite Coatings on a Nanotubular TiO2 Layer
PublicationThe surface treatment of titanium implants has been applied mainly to increase surface bioactivity and, more recently, to introduce antibacterial properties. To this end, composite coatings have been investigated, particularly those based on hydroxyapatite. The present research was aimed at the development of another coating type, chitosan–nanosilver, deposited on a Ti13Zr13Nb alloy. The research comprised characterization of the...
-
Electrodeposited Biocoatings, Their Properties and Fabrication Technologies: A Review
PublicationCoatings deposited under an electric field are applied for the surface modification of biomaterials. This review is aimed to characterize the state-of-art in this area with an emphasis on the advantages and disadvantages of used methods, process determinants, and properties of coatings. Over 170 articles, published mainly during the last ten years, were chosen, and reviewed as the most representative. The most recent developments...
-
Effects of Micro-Arc Oxidation Process Parameters on Characteristics of Calcium-Phosphate Containing Oxide Layers on the Selective Laser Melted Ti13Zr13Nb Alloy
PublicationTitania-based films on selective laser melted Ti13Zr13Nb have been formed by micro-arc oxidation (MAO) at different process parameters (voltage, current, processing time) in order to evaluate the impact of MAO process parameters in calcium and phosphate (Ca + P) containing electrolyte on surface characteristic, early-stage bioactivity, nanomechanical properties, and adhesion between the oxide coatings and substrate. The surface...
-
Effects of CO2 and Nd:YAG Laser Remelting of the Ti6Al4V Alloy on the Surface Quality and Residual Stresses
PublicationThe titanium alloys are materials susceptible to tribological wear and the laser treatment can be applied in surface treatment processes to obtain for example higher hardness level. From the other side, it is important to take into consideration, that hardness increase that can be connected with cracks . The aim of this research was to investigate the effects of different lasers and the process parameters on the form and level...
-
Effect of Thermal Treatment of Birch Wood by Saturated Water Vapor on Granulometric Composition of Chips from Sawing and Milling Processes from the Point of View of Its Processing to Composites
PublicationThe goal of this work is to investigate the impact of thermal modification of birch wood with saturated steam on the particle size distribution of the sawing and milling process. Birch wood (Betula pendula Roth) is an excellent source to produce plywood boards. Wastes from mechanical processing of birch wood are suitable to produce composite materials. Granulometric analyses of chips from sawing processes on the PRW 15M frame saw,...
-
Effect of the Drying Method of Pine and Beech Wood on Fracture Toughness and Shear Yield Stress
PublicationThe modern wood converting processes consists of several stages and material drying belongs to the most influencing future performances of products. The procedure of drying wood is usually realized between subsequent sawing operations, affecting significantly cutting conditions and general properties of material. An alternative methodology for determination of mechanical properties (fracture toughness and shear yield stress) based...
-
Effect of sintering temperature on electrochemical performance of porous SrTi1-xFexO3-δ (x = 0.35, 0.5, 0.7) oxygen electrodes for solid oxide cells
PublicationThis work evaluates the effects of the sintering temperature (800 °C, 900 °C, 1000 °C) of SrTi1-xFexO3-δ (x = 0.35, 0.5, 0.7) porous electrodes on their electrochemical performance as potential oxygen electrode materials of solid oxide cells. The materials were prepared by a solid-state reaction method and revealed the expected cubic perovskite structure. After milling, the powders were characterised by a sub-micrometre particle...
-
Effect of pine impregnation and feed speed on sound level and cutting power in wood sawing
PublicationThe sound levels along with the cutting power registered during the sawing process of the impregnated and non-impregnated pine wood at two feed speeds are shown and compared in this paper. Statistically significant differences in the acoustic signals occurred at the lower feed rate. The differences became smaller with an increase in the feed speed. In contrast to the sound signal, the differences...
-
Effect of electrode waterproof coating on quality of underwater wet welded joints
PublicationIn this paper, the effects of different hydrophobic coatings on the surface of covered electrodes on the quality of wet welded carbon steel joints were discussed. Commonly available hydrophobic substances used in industrial applications were selected for the research. The aim of using waterproof coatings was to check the possibility to decreasing the susceptibility of highstrength low-alloy S460N steel to cold cracking. During...
-
Druk 3D części z tworzyw sztucznych na skalę przemysłową w technologii SLS
PublicationFirma EOS, wiodący i światowy dostawca technologii przemysłowego wykorzystania druku 3D dla materiałów metalicznych i polimerowych, zaprezentowała na targach formnext 2017 nowy system EOS P500, przeznaczony do addytywnego wytwarzania modeli. Drukarka 3D adresowana jest dla przedsiębiorstw chcących wytwarzać na skalę przemysłową części i elementy z tworzyw sztucznych o wysokiej jakości.
-
Druk 3D części z tworzyw sztucznych na skalę przemysłową w technologii SLS
PublicationFirma EOS, wiodący i światowy dostawca technologii przemysłowego wykorzystania druku 3D dla materiałów metalicznych i polimerowych, zaprezentowała na targach formnext 2017 nowy system EOS P500, przeznaczony do addytywnego wytwarzania modeli. Drukarka 3D adresowana jest dla przedsiębiorstw chcących wytwarzać na skalę przemysłową części i elementy z tworzyw sztucznych o wysokiej jakości.
-
Dissimilar underwater wet welding of HSLA steels
PublicationThe high-strength low-alloy S460ML and S460N steels were chosen for underwater wet welding of dissimilar T-joints using covered electrodes. For improving the quality of joints, the temper bead welding (TBW) method was used. The application of TBW in pad welding conditions has been investigated earlier but the possibility of usage of this technique in welded joints was not analyzed. The main aim of the study was to check the influence...
-
Degradation of ferritic X10CrAlSi18 stainless steel caused by slurry
PublicationThe slurry erosion tests of ferritic X10CrAlSi18 steel were carried out using a slurry pot device. In order to investigate the erosion process, two series of tests were performed: first one with a constant impact velocity of 5 m/s, 7 m/s and 9 m/s and the second one, during which the impact velocity was changed after every exposure. During each test, an influence of test conditions on volume loss, surface hardness and roughness...
-
Deformation and Surface Color Changes of Beech and Oak Wood Lamellas Resulting from the Drying Process
PublicationThe drying process was examined relative to parameters’ influence on the deformation and surface layer color changes of beech wood (Fagus sylvatica L.) and oak wood (Quercus robur L.). The goal was to analyze the impact of drying process conditions, wood and growth rings types, and load on the deformation and surface color changes of drying thin wooden elements. A further aim was to reduce the time of the lamella drying and minimize...
-
Cutting model parameters from frame sawing of natural and impregnated Scots pine (Pinus sylvestris L.)
PublicationIn this paper, absolute and density normalized cutting model parameters of natural and impregnated Scots pine (Pinus sylvestris L.) are shown and a method for the calculation of their corresponding material properties in the principal material directions of wood is presented. The parameters were determined from measurements of cutting power on a sash gang saw, and are in detail the fracture toughness and the shear yield strength...
-
Comprehensive Evaluation of the Biological Properties of Surface-Modified Titanium Alloy Implants
PublicationAn increasing interest in the fabrication of implants made of titanium and its alloys results from their capacity to be integrated into the bone system. This integration is facilitated by different modifications of the implant surface. Here, we assessed the bioactivity of amorphous titania nanoporous and nanotubular coatings (TNTs), produced by electrochemical oxidation of Ti6Al4V orthopedic implants’ surface. The chemical composition...
-
COLLABORATIVE LEARNING ENVIRONMENT FOR ENGINEERING EDUCATION (COLED)
PublicationCollaborative Learning Environment for Engineering Education is a European project implemented under the Erasmus + program, The main goal of 5 partners from 4 different European countries – Bulgaria, Poland, Portugal and Romania is to develop an innovative collaborative training approach, encompassing curricula related to the introduction of enterprise automation. Project activities are carried out in the period from Dctober 2018...
-
Biological and mechanical properties of bone cement with nanoarticles - in vitro and in vivo research
PublicationDespite antibiotic preventive treatment both before and after implant implementation, the risks of infection are real. These infections develop at the implant surface a few months after inserting them into the body. To prevent the development of bacteria and reduce the risk of infection, implants coated with nanoparticles are used. The Mechanical Department of the Technical University of Gdansk carries out research into using bone...
-
Badania nieniszczące jakości spoin szyn poddźwigowych na nabrzeżu przeładunkowym T1 w DCT w Porcie Północnym
PublicationCelem podstawowym niniejszego opracowania było sprawdzenie za pomocą NDT jakości spoin wykonanych w ramach prac naprawczych w DCT w roku 2017 (styki szyn poddźwigowych typu A120 na nabrzeżu T1 w DCT Port Północny Gdańsk). W ramach opracowania: 1) Ustalono zakres badań - na podstawie potrzeb Kierownictwa Infrastrukury DCT; b) Analizowano wyniki badań nieniszczących wykonanych w sierpniu 2017r.;...
-
Autogenous Fiber Laser Welding of 316L Austenitic and 2304 Lean Duplex Stainless Steels
PublicationThis study presents results of experimental tests on quality of dissimilar welded joints between 316L austenitic and 2304 lean duplex stainless steels, welded without ceramic backing. Fiber laser welded butt joints at a thickness of 8 mm were subjected to non‐destructive testing (visual and penetrant), destructive testing (static tensile test, bending test, and microhardness measurements) and structure observations (macro‐ and...
-
APPLICATION OF APRIORI ALGORITHM IN THE LAMINATION PROCESS IN YACHT PRODUCTION
PublicationThe article specifies the dependence of defects occurring in the lamination process in the production of yachts. Despite great knowledge about their genesis, they cannot be completely eliminated. Authentic data obtained through cooperation with one of the Polish yacht shipyards during the years 2013–2017 were used for the analysis. To perform a simulation, the sample size was observed in 1450 samples, consisting of 6 models of...
-
Application of 3D printing metal powder technology in the manufacture of components with complex geometries
PublicationThe possibilities of using 3D printing powder technologies for making objects with complex geometries were presented. For this purpose, selected examples of elements with different geometries were used, which were built using metal powder methods – DMLS (direct metal laser sintering) / SLM (selective laser melting). Simultaneously, the indicated elements concern those areas of industry where 3D printing technology has been widely...
-
Analysis of flat compensator lapping in an assembly process
PublicationPrzedstawiono sposób analizy docierania kompensatora płaskiego podczas montażu połączenia konstrukcyjnego. Wyznaczono czas główny obróbki i koszty operacji docierania jednotarczowego
-
Analiza ilościowa technologiczności konstrukcji oprzyrządowania obróbkowego - studium przypadku
PublicationOmówiono ilościową metodę oceny technologiczności konstrukcji oprzyrządowania obróbkowego. Przedstawiono przykład oceny technologiczności zaprojektowanych trzech wersji uchwytów wiertarskich w procesie technologicznym części klasy dźwignia
-
ALTERNATIVE, DIRECT SYNTHESIS METHOD OF THE CERAMIC SOLID SOLUTIONS BASED ON BaTiO3 THROUGH A HIGH ENERGY BALL MILLING
PublicationPolycrystalline samples BaTiO3 and the solid solutions Ba0.9Sr0.1TiO3, Ba0.9Sr0.1Ti0.9Sn0.1O3, Ba0.9Sr0.1Ti0.8Sn0.2O3 were obtained by means of a mechanochemical treatment based on the high-energy ball milling technique and next a high temperature solid state reaction method. The influence of synthesis condition on microstructural, dielectric and ferroelectric properties of obtained solid solutions were investigated. The structure...
-
Absolwent Wydziału Mechanicznego Złotym Inżynierem "Przeglądu Technicznego"
PublicationPrzedstawiono sylwetke i dorobek mgr. inż. Janusza Ochocińskiego, tegorocznego laureata plebiscytu czasopima "Przegląd Techniczny", o tytuł Złotego Inżyniera 2019 w kategorii Menedżer. Pan Janusz Ochociński jest absolwentem Wydziału Mechanicznego Technologicznego Politechniki Gdańskiej z roku 1981.
-
A pilot study to assess an in-process inspection method for small diameter holes produced by Direct Metal Laser Sintering
PublicationPurpose The purpose of this research is to evaluate the geometric quality of small diameter holes in parts printed by DMLS technology. An in-process optical inspection method is proposed and assessed during a pilot study. The influence of the theoretical hole diameter assumed in a CAD system and the sample thickness (hole length) on the hole clearance was analysed. Design/methodology/approach The samples made of two different...
-
A Critical Reanalysis of Uncontrollable Washboarding Phenomenon in Metal Band Sawing
PublicationThe article analyzes the cutting process of hard bars. Investigations conducted in industrial conditions demonstrated the presence of surface errors in the machined workpieces in the form of washboard patterns. The purpose of this study was to analyze the results of cutting on band sawing machines with different band saw blades. The cutting processes were conducted on three different horizontal band sawing machine types. Analyzed...
-
45 lat minęło - kolejne spotkanie technologów na Wydziale Mechanicznym
PublicationOmówiono przebieg Jubileuszowego Zjazdu Absolwentów Wydziału Mechanicznego Politechniki Gdańskiej, którzy ukończyli studia wiosną i jesienią w roku 1974.
Year 2019
-
Zastosowanie uchwytów modułowych w operacjach spawalniczych
PublicationW artykule przedstawiono przykłady wykorzystania uchwytów składanych w wybranych operacjach spawalniczych. Analizowano zaprojektowane oprzyrządowanie przedmiotowe w spawaniu trzech półfabrykatów typu korpus lub dźwignia. W konfiguracji tego typu uchwytów modułowych wykorzystano elementy wytwarzane seryjnie przez firmę Siegmund GmbH.
-
Zastosowanie metody sztucznych baz w analizie docierania powierzchni płaskich
PublicationPrzedstawiono wyniki badań zużycia pierścieni prowadzących w układzie kinematycznym standardowej docierarki jednotarczowej. Do analiz wykorzystano metodę sztucznych baz Vickersa.
-
Wytwarzanie powłok hydroksyapatytowych z osłoną biologiczną na stopie tytanu
PublicationObecnie powłoki hydroksyapatytowe wytwarzane na implantach ze stopów tytanu nie w pełni spełniają stawiane im wymagania. Charakteryzują się dużą grubością i słabą adhezją do metalicznego podłoża. Ponadto nie posiadają właściwości antybakteryjnych, a tworzenie biofilmu na powierzchni implantu jest jedną z głównych przyczyn odrzucenia implantu i potrzeby jego rewizji. Celem naukowym pracy było określenie wpływu składu roztworu oraz...
-
Wykorzystanie e-narzędzi w nauczaniu, egzaminacji i certyfikacji Autodesk
PublicationAutoryzowane Centrum Szkolenia Autodesk Politechniki Gdańskiej zostało założone w 1995 roku. Stanowiło odpowiedź na rosnące zainteresowanie zdobywaniem umiejętności obsługi oprogramowania typu CAD wśród studentów i młodych inżynierów. Rosnące zainteresowanie zaowocowało stopniowym wdrażaniem kolejnych narzędzi e-learningowych. Wraz ze zdobyciem statusu Autoryzowanego Akademickiego Partnera Autodesk w 2016 roku pojawiły się nowe...
-
Wpływ wielkości równoważnika węgla na spawalność stali o podwyższonej wytrzymałości w środowisku wodnym
PublicationZ roku na rok coraz większe zastosowanie na konstrukcje offshore znajdują stale o podwyższonej wytrzymałości. Konstrukcje takie, ze względu na środowisko, w którym pracują wymagają częstszych napraw, niż w przypadku konstrukcji lądowych. Ze względów ekonomicznych naprawy odbywają się w warunkach podwodnych, jednakże woda znacząco pogarsza spawalność stali. W pracy przedstawiono wyniki próby spawalności CTS dla stali S460ML i S460N,...
-
Wpływ temperatury przesycania na właściwości złączy spawanych rur ze stali typu Lean Duplex 2101
PublicationW artykule przedstawiono wpływ temperatury przesycania w powiązaniu z technologią spawania wzdłużnego metodą TIG (142) rurek stosowanych w budowie wy-mienników ciepła ze stali Lean Duplex 2101. Przedstawiono wyniki badań wytrzymałości na rozciąganie, prób technologicznych określających właściwości plastyczne, makro- i mikro-skopowe oraz pomiaru zawartości ferrytu delta metodą magnetyczną. Ustalono, że zmiana temperatury przesycania...
-
Wpływ środowiska spawania na własności złączy próbnych Tekken ze stali S355J2C+N
PublicationIstnieją trzy metody spawania pod wodą, sucha, mokra oraz pośrednia między nimi, wykorzystująca lokalną komorę suchą. Ze względu na niskie koszty najszerzej rozpowszechnioną jest metoda mokra z wykorzystaniem elektrod otulonych. Woda jako środowisko spawania znacznie utrudnia przeprowadzenie procesu, którego realizacja niesie ze sobą wiele problemów. Pierwszym z nich jest zła widoczność po-wstającego złącza oraz niestabilność...
-
Wpływ metody trawienia i spiekania na właściwości mechaniczne powłok z nanorurek węglowych osadzonych elektroforetycznie na podłożu Ti13Nb13Zr
PublicationDo eksperymentu użyto stopu tytanu Ti13Zr13Nb, który ze względu na swój skład chemiczny i właściwości mechaniczne stanowi doskonały materiał do zastosowań w inżynierii medycznej. Celem pracy była ocena wpływu przygotowania podłoża (rodzaj zastosowanego odczynnika trawiącego) oraz obróbki końcowej (proces spiekania) powłok z wielościennych nanorurek węglowych na ich właściwości mechaniczne (nanotwardość, moduł Younga). Do wytworzenia...
-
Wpływ intensywności prędkości uderzenia na niszczenie cząstkami stałymi w środowisku wodnym stali X10CrAlSi18
PublicationErozja cząstkami stałymi w środowisku wodnym jest złożonym zjawiskiem ze względu na jednoczesne oddziaływanie wielu czynników, takich jak prędkość i kąt uderzenia, koncentracja cząstek, własności materiału i cząstek stałych, prowadząc do efektu synergicznego. Zmiana jakiegokolwiek parametru procesu erozyjnego prowadzi do zmiany szybkości erozji. Z tego względu istotne jest badanie wpływu poszczególnych czynników na proces niszczenia....
-
Titanium Scaffolds – Hopes and Limitations
PublicationThe state-of-art on titanium scaffolds is briefly reviewed. The real hopes from medicine associated with scaffolds are indicated. The limitations of different scaffolds associated with their mechanical, chemical and biological properties are discussed. The great importance of titanium scaffolds is demonstrated as the materials of high biocompatibility and corrosion resistance, fair mechanical properties and important biological...
-
Titania Nanotubes/Hydroxyapatite Nanocomposites Produced with the Use of the Atomic Layer Deposition Technique: Estimation of Bioactivity and Nanomechanical Properties
PublicationTitanium dioxide nanotubes/hydroxyapatite nanocomposites were produced on a titanium alloy (Ti6Al4V/TNT/HA) and studied as a biocompatible coating for an implant surface modification. As a novel approach for this type of nanocomposite fabrication, the atomic layer deposition (ALD) method with an extremely low number of cycles was used to enrich titania nanotubes (TNT) with a very thin hydroxyapatite coating. X-ray diffraction (XRD)...
-
Titania Nanofiber Scaffolds with Enhanced Biointegration Activity—Preliminary In Vitro Studies
PublicationThe increasing need for novel bone replacement materials has been driving numerous studies on modifying their surface to stimulate osteogenic cells expansion and to accelerate bone tissue regeneration. The goal of the presented study was to optimize the production of titania-based bioactive materials with high porosity and defined nanostructure, which supports the cell viability and growth. We have chosen to our experiments TiO2...
-
Thermal and technological aspects of double face grinding of Al2O3 ceramic materials
PublicationDouble face grinding with planetary kinematics is a process to manufacture workpieces with plan parallel functional surfaces, such as bearing rings or sealing shims. In order to increase the economic efficiency of this process, it has to be advanced permanently. The temperature in the contact zone of most grinding processes has a huge influence on the process efficiency and the workpiece qualities. In contrast to most grinding...
-
The Morphology, Structure, Mechanical Properties and Biocompatibility of Nanotubular Titania Coatings before and after Autoclaving Process
PublicationThe autoclaving process is one of the sterilization procedures of implantable devices. Therefore, it is important to assess the impact of hot steam at high pressure on the morphology, structure, and properties of implants modified by nanocomposite coatings. In our works, we focused on studies on amorphous titania nanotubes produced by titanium alloy (Ti6Al4V) electrochemical oxidation in the potential range 5–60 V. Half of the...
-
The influence of the welding environment on the properties of Tekken joints made from S355J2C+N steel
PublicationThere are three main methods of underwater welding: dry, wet and intermediate between them, by using the local dry chamber. Due to low costs, the most common method is the wet welding with the use of covered electrodes. Water as a welding environment carries out a lot of problems. The first is limited visibility and instability of the welding arc. The biggest problem during underwater welding is high susceptibility to cold cracking,...
-
The influence of the carbon equivalent on the weldability of high-strength low-alloy steel in the water environment
PublicationFrom many years, the high strength low alloy steels are often used for offshore constructions. This constructions, due to the environment in which they work, require more frequent repairs than the constructions from the land. For economic reasons, repairs take place in the underwater conditions, however water significantly decreases the weldability of steel. The paper presents the results of the CTS weldability test for S460ML...
-
The influence of solution annealing temperature on the properties of Lean Duplex 2101 welded joints in tubes
PublicationThe article presents a technology of TIG longitudinal welding without filler material (142) of heat exchanger tubes made of Lean Duplex 2101. The results of studies on the effect of heat treatment (solution annealing) on tensile strength, plasticity, delta ferrite and the structure of smooth tubes are shown. It was found, that the change in solution annealing temperature across the tested range has an impact on mechanical properties...
-
The Influence of Laser Alloying of Ti13Nb13Zr on Surface Topography and Properties
PublicationThe laser alloying is a continually developing surface treatment because of its significant and specific structuration of a surface. In particular, it is applied for Ti alloys, being now the most essential biomaterials` group for load-bearing implants. The present research was performed on the Ti13Nb13Zr alloy subject to laser modification in order to determine the treatment effects on surface topography and its some mechanical...
-
The Influence of Iron Doping on Performance of SrTi1-XFexO3-δ Perovskite Oxygen Electrode for SOFC
PublicationSolid Oxide Fuel Cells (SOFC) are based on electrolytes and mixed ionic and electronic conductivity (MIEC) materials. The need to reduce costs causes an increase in interest of new compounds suitable for operating temperatures between 600 °C and 800 °C. The SrTi1-xFexO3 (STF) perovskite material is a perspective material that could be used for the oxygen electrodes. In this work STF materials with different content of iron (x =...
-
The impact of drying and steaming processes on surface color changes of tension ad normal beech wood
PublicationThe aim of the article is to present the influence of high temperature to selected properties of beech wood (Fagus sylvatica L.). The properties such as moisture content, color changes and longitudinal warping were analyzed. The quality of beech wood is determined based on structure and properties of wood, frequency of defects in wood material. The tension wood is considered as an important wood defect causing negative alterations...
-
THE EFFECT OF WOOD DRYING METHOD ON THE GRANULARITY OF SAWDUST OBTAINED DURING THE SAWING PROCESS USING THE FRAME SAWING MACHINE
PublicationThe experimental results of the study focused on the effect of drying processes of warm air drying at the temperature of 6580°C and warm air-steam mixture drying at the temperature of 105°C of pine and beech wood to the size of sawdust grains created by cutting using RPW 15M frame saw is presented in the paper. Particle size analysis of dry sawdust was performed using two methods - screening method and optical method based on...
-
The Effect of Surface Modification of Ti13Zr13Nb Alloy on Adhesion of Antibiotic and Nanosilver-Loaded Bone Cement Coatings Dedicated for Application as Spacers
PublicationSpacers, in terms of instruments used in revision surgery for the local treatment of postoperative infection, are usually made of metal rod covered by antibiotic-loaded bone cement. One of the main limitations of this temporary implant is the debonding effect of metal–bone cement interface, leading to aseptic loosening. Material selection, as well as surface treatment, should be evaluated in order to minimize the risk of fraction...
-
The effect of laser on metal surfaces for multidisciplinary usage in material and thermal engineering
PublicationThe subject of heat transfer and cooling systems is still a matter of contention in many different fields of science and industry. Infrigidation is much more difficult than warming, and so, much more needed in more and more different devices, starting from massive industrial machinery and air conditioning in commercial buildings, up to micro and nano-surgery tools. In fact, the size of many cooling systems is still a problem. It...
-
The effect of an active force while slide diamond burnishing of wooden shafts upon process quality
PublicationThe quality of the surface of wooden elements that have been turned and burnished has got a crucial meaning in the whole production process flow, since the obtained effects affect the quality of the wooden surface after finishing (coating, painting). In the paper, selected results of the investigation of the effect of the burnishing process on the surface quality of the elements after turning are presented. Research experiments...
-
Tests for lapping of flat surfaces of ceramic elements with forced dosing of abrasive slurry
PublicationPrzedstawiono zagadnienia dotyczące systemu wymuszonego dawkowania zawiesiny ściernej w docieraniu jednotarczowym powierzchni płaskich. Opisano zalety takiego systemu dozowania płynnej zawiesiny ściernej. Omówiono wybrane wyniki badań docierania elementów z ceramiki technicznej. Analizowano wpływ podstawowych warunków dawkowania zawiesiny na ubytek liniowy próbek.
-
Śladami wybitnego inżyniera - Ernest Malinowski
PublicationPrzedstawiono życie i działalność wybitnego polskiego inżyniera kolejnictwa Ernesta Malinowskiego i peruwiańskiego patrioty. Omówiono obchody jubileuszowe związane z jego 200. rocznicą urodzin i 120. rocznicą śmierci, mające miejsce zarówno w Polsce, jak i w Peru.
-
Śladami wybitnego absolwenta - Edward Kajdański
PublicationPrzedstawiono sylwetkę i dokonania twórcze Edwarda Kajdańskiego, dziennikarza, pisarza, malarza i dyplomaty, absolwenta Wydziału Technologii Maszyn Politechniki Gdańskiej z roku 1960.
-
Surgical Site Infection after Breast Surgery: A Retrospective Analysis of 5-Year Postoperative Data from a Single Center in Poland
PublicationBackground and Objectives: Surgical site infection (SSI) is a significant complication of non-reconstructive and reconstructive breast surgery. This study aimed to assess SSI after breast surgery over five years in a single center in Poland. The microorganisms responsible for SSI and their antibiotic susceptibilities were determined. Materials and Methods: Data from 2129 patients acquired over five years postoperatively by the...
-
Surface Texture Analysis of Hardened Shafts after Ceramic Ball Burnishing
PublicationThis article represents the results of testing the surface condition of shafts manufactured by the burnishing process. The shafts with a hardness of approximately 62 HRC (Rockwell C). were burnished with a ceramic ball (Si3N4), where the force range was controlled by the means of a hydraulic system. The machining process consisted of hard turning shafts with cubic boron nitride (CBN) inserts, followed by burnishing with the use...
-
Sulfate‐reducing bacteria‐assisted hydrogen‐induced stress cracking of 2205 duplex stainless steels
PublicationThe paper presents the results of a laboratory investigation of the microbiologically assisted hydrogen‐induced stress cracking (HISC) of 2,205 duplex stainless steel (DSS). The testing of susceptibility toward HISC was performed with two different methods. Precharged in sulfate‐reducing bacteria (SRB), inoculated medium samples were subjected to slow strain‐rate testing in artificial seawater. In situ constant load tests were...
-
Role of bead sequence in underwater welding
PublicationThis paper presents examinations of the role of the bead sequence in underwater welding. Two specimens of wet welded layers made by covered electrodes with the use of normalized S355G10+N steel were welded by a reasonable bead sequence. For each specimen, metallographic macro- and micro-scopic tests were done. Then, Vickers HV10 hardness measurements were conducted for each pad weld in the welded layer. The results show that welding...
-
Quality increase for single-welded joints of thin-walled structures by means of simulation modelling
PublicationThe Simulation calculation module and the SolidWorks software package have helped to define the optimal shape and dimensions of single-welded joints which may serve the basis for calculating the process parameters of welding. Having compared the models with different weld cross-sections the authors have defined that the weld height and width do not significantly affect the stress concentration, and the stress concentration and...
-
Qualification of brazing procedure for furnace brazing of austenitic steel according to requirements of the ASME BPVC section IX
PublicationThe article presents the procedure for qualifying brazing technology in a vacuum furnace on the example of stainless steel elements joined with copper filler material from the F-No group. 105, in accordance with the ASME Sec. IX, part QB (ASME Boiler and Pressure Vessel Code. Qualification Standard for Welding, Brazing and Fusing; Procedures; Welders; Brazers; and Welding, Brazing and Fusing Operators). The essential variables...
-
Properties of Nanohydroxyapatite Coatings Doped with Nanocopper, Obtained by Electrophoretic Deposition on Ti13Zr13Nb Alloy
PublicationNowadays, hydroxyapatite coatings are the most common surface modification of long-term implants. These coatings are characterized by high thickness and poor adhesion to the metallic substrate. The present research is aimed at characterizing the properties of nanohydroxyapatite (nanoHAp) with the addition of copper nanoparticle (nanoCu) coatings deposited on the Ti13Zr13Nb alloy by an electrophoresis process. The deposition of...
-
Projekt aCiret odpowiedzią na wyzwania przemysłu 4.0
PublicationDruga dekada XXI w. jest początkiem nowej rewolucji przemysłowej, określanej jako przemysł 4.0. Coraz powszechniejsze systemy cyberfizyczne, internet rzeczy, obliczenia i procesy sterowane w chmurze wymagają wysoko wykwalifikowanych pracowników, uzbrojonych w ogólną i specjalistyczną wiedzę oraz doświadczenie, wykazujących się przedsiębiorczością i inicjatywą. Problem braku odpowiedniej kadry dotyka firmy z sektora przemysłowego,...
-
Process layout planning and optimised product range selection in manufacture of wooden construction sets
PublicationThis paper introduces a systematic deterministic framework for planning and the analysis of facility layouts aimed at manufacturing a variety of parts, as components of specific end products. The essence of the proposed approach lies in the decomposition of a traditional job-shop into layout modules of generic material flow patterns, that inherently yields improved efficiency of the entire system. It entails the use of a relevant...
-
Problems of Flaking in Strengthening Shaft Burnishing
PublicationThe article presents the results of testing the surface condition of shafts manufactured by a strengthening rolling burnishing process. The shafts with a hardness about 220 HB were burnished with a roller with different force. Researches were carried out with particular attention to the structure of the outflowing material in the tool zone during burnishing process. The article presents the results of the examinations of burnished...
-
Powder metallurgy of the porous Ti-13Nb-13Zr alloy of different powder grain size
PublicationThe objective of the present project was to determine the effects of powder granulation (fraction of grain size) for the Ti-13Nb-13Zr alloy, produced by powder metallurgy, on its porosity, grain cohesion, compressive strength, and Young`s modulus. Two powder fractions, 45–105 µm, and 106–250 µm were applied. The 50 mass pct of NH4HCO3 was added as a space holder. The specimens were in compaction stage uniaxially pressed at pressure...
-
Poroelastic Material for Urban Roads Wearing Courses
PublicationConventional road materials used for producing wearing courses of roads are based on mineral aggregate and bituminous or Portland cement binders. The road materials must be optimized for different properties, including skid resistance, durability, rolling resistance and tire/road noise. Unfortunately, it seems that within classic technologies it is very difficult to achieve further reduction of tire/road noise. Innovative porous...
-
Pomiary i analiza wielkości mikroziaren ściernych.
PublicationOmówiono skomputeryzowana analizę wielkości i kształtu mikroziaren ściernych. W badaniach mikroziaren węglika boru, czarnego i zielonego weglika krzemu oraz elektrokorundu zwykłego i szlachetnego stosowano mikroskopię optyczną oraz oprogramowanie MultiScan.
-
Piezoresponse force microscopy and dielectric spectroscopy study of Ba0.6Sr0.4TiO3 thin films
PublicationResearch on synthesis, characterization and determination of processing – structure – property relationships of commercially important ferroelectric thin films has been performed. The sol-gel-type solution deposition technique was applied to produce good quality thin films of Ba0.6Sr0.4TiO3 (BST60/40) chemical composition on the stainless steel substrates. The thin films were characterized in terms of their microstructure, crystal...
-
pH-dependent composite coatings for controlled drug delivery system - Review
PublicationNowadays in case of long-term implants, the most common postoperative complications are bacterial infections, which in consequence may provoke loos- ening of the implants in the primary phase of stabilization. Bacterial infections are currently the most frequent cause of revision surgery of the implants such as hip joint endoprosthesis, knee joint endoprosthesis and dental implants. In order to provide the local and long-term antibacterial...
-
Parametry kinematyczne docierarek tarczowych
PublicationOmówiono analizę kinematyki docierania powierzchni płaskich w układach jedno- i dwutarczowych. Przedstawiono opracowane modele standardowych układów kinematycznych. Wyznaczono zakresy zmienności prędkości docierania i wartości przyspieszeń w analizowanych układach kinematycznych
-
Opracowanie ekspertyzy dotyczącej przyczyn pękania łopatek wirnika SP turbiny PG1 typu 13UP55
PublicationZakres badań i analiz dotyczył ustalenia przyczyn pękania elementów łopatek wirnika SPA5 turbiny TG1 typu 13UP55 obejmował: 1. wykonanie badań składu chemicznego stali, z której wykonano łopatki dostarczone przez Zleceniodawcę dwoma metodami, 2. badania mikroobszarów zniszczenia łopatek na mikroskopie elektronowym skaningowym z mikroanalizatorem EDS, 3. badania metalograficzne makroskopowe i mikroskopowe fragmentów...
-
Operational harmfulness of surface contamination with abrasive after the technological lapping process = Szkodliwość eksploatacyjna skażenia powierzchni ścierniwem po procesie docierania technologicznego.
PublicationPrzestawiono metodykę i wyniki jakościowych i ilościowych badań skażenia powierzchni mikroziarnami ściernymi oraz wpływ warunków docierania na intensywność zjawiska. W badaniach wykorzystano mikroskopie skaningową i mikroanalizę rentgenowską.
-
NUMERICAL SIMULATIONS OF HONING PROCESS OF THIN WALL CYLINDER LINERS, WITH CONSTANT AND WITH VARIABLE THICKNESS OF WALL OF HONED PARTS
PublicationNumerical simulations of honing process of thin-wall cylinder liners, with constant and with variable thickness of the wall of honed workpieces can improve and can help to conduct the experimental research of honing process and can improve the honing process. A very valuable research assumption, before performing the numerical analysis of computer simulation of honing process, is the measurement of the real geometry of the honing...
-
Non-conventional approach in single-sided lapping process: kinematic analysis and parameters optimization
PublicationThe lapping process is strongly affected by a number of input parameters. One of the fundamental mechanical processes in lapping is the abrasive effect of particles. In order to examine the influence of the kinematic parameters on the lapping uniformity of unconventional single-sided machine, numerical simulations of particles sliding trajectories are performed. Changing the kinematic parameters, e.g., rotational velocities or...
-
Low temperature broad band dielectric spectroscopy of multiferroic Bi6Fe2Ti3O18 ceramics
PublicationIn the present research the tool of broadband dielectric spectroscopy was utilized to characterize dielectric behavior of Bi6Fe2Ti3O18 (BFTO) Aurivillius-type multiferroic ceramics. Dielectric response of BFTO ceramics was studied in the frequency domain (Δν=0.1Hz – 10MHz) within the temperature range ΔT=-100°C – 200°C. The Kramers-Kronig data validation test was employed to validate the impedance data measurements and it was found...
-
Low Noise Poroelastic Road Pavements Based On Bituminous Binder
PublicationTire/road noise is the dominant source of traffic noise. It depends both on the tire design and on the characteristics of road pavements as well as on the vehicles’ operating conditions. Due to the fact that conventional (pneumatic) car tires have almost reached the limits of their ability to further reduce their noisiness, it is widely believed that the additional reduction of tire noise will be possible mainly through modifications...
-
Laserowa modyfikacja treści i nanonieporozumienia drukowane w 3D
PublicationW obliczu wielkich wyzwań naukowych zapomina się czasem o drobnych niedopowiedzeniach, które mogą zaważyć na wyniku całego badania. Szeroka współpraca, zwłaszcza interdyscyplinarna, jest niezbędna do osiągnięcia sukcesu, ale bywa również przyczyną powstawania nieporozumień i formułowania błędnych założeń technicznych. Nadużywanie modnych słów kluczowych może doprowadzić do szeregu nieporozumień i wyciągania fałszywych wniosków...
-
Lapping flat surfaces with forced dosing of abrasive suspension
PublicationPrzedstawiono zbudowane stanowisko do badań wymuszonego dawkowania zawiesiny ściernej w procesie jednostronnego docierania powierzchni płaskich. Podano przyjęty program badań oraz sposób opracowania wyników realizowanych eksperymentów.
-
Lapping flat surfaces with forced dosing of abrasive suspension
PublicationPrzedstawiono zbudowane stanowisko badawcze umożliwiające wymuszone dozowanie zawiesiny ściernej w operacji docierania jednotarczowego powierzchni płaskich. Podano program badań własnych oraz sposób opracowania otrzymanych wyników realizowanych eksperymentów.
-
Kwalifikowanie technologii lutowania twardego próżniowego stali austenitycznej zgodnie z wymaganiami przepisów ASME BPVC, sekcja IX
PublicationW artykule przedstawiono procedurę kwalifikowania technologii lutowania twardego w piecu próżniowym na przykładzie elementów ze stali wysokostopowej nierdzewnej austenitycznej łączonych lutem miedzianym z grupy F-No. 105, zgodnie z przepisami ASME Sec. IX, part QB (ASME Boiler and Pressure Vessel Code. Qualification Standard for Welding, Brazing and Fusing; Procedures; Welders; Brazers; and Welding, Brazing and Fusing Operators)....
-
Kształtowanie właściwości warstwy wierzchniej podczas szlifowania
PublicationW artykule scharakteryzowano szlifowanie powierzchni płaskich połączone ze zmianami właściwości warstwy wierzchniej, zwłaszcza poprzez jej zahartowanie. Omówiono problemy związane z tzw. technologią grind-hardening. Dodatkowo przedstawiono badania, w których po procesie szlifowania uzyskano lepsze właściwości elementu obrabianego wskutek odkształcenia plastycznego.
-
Kształtowanie jakości powierzchni powłok Cr2O3 przez docieranie
PublicationOmówiono wyniki badań technologicznego docierania powłok ceramicznych Cr2O3, które wykazały przydatność tego procesu w uzyskaniu wysokiej jakości powierzchni, charakteryzującej się niską wartością parametru chropowatości Ra.
-
Konstrukcyjno-technologiczne aspekty stosowania uchwytów modułowych i specjalnych w operacjach obróbkowych
PublicationPrzedstawiono konstrukcje zaprojektowanych uchwytów modułowych i specjalnych. Wyznaczono, wariantowo, koszty uchwytów dla tych samych typów elementów. Zastosowana analiza może być między innymi wykorzystana w procesie kształcenia inżynierskiego mechaników technologów.
-
Kinematyka docierarek tarczowych
PublicationPrzeanalizowano kinematykę docierania powierzchni płaskich w układach jedno- i dwutarczowych. Przedstawiono opracowane modele standardowych układów kinematycznych. Wyznaczono zakresy zmienności prędkości docierania i wartości przyspieszeń w analizowanych układach wykonawczych docierarek.
-
IV Światowy Zjazd Inżynierów Polskich i XXVI Kongres Techników Polskich w Krakowie
PublicationOmówiono przebieg i przesłanie IV Światowego Zjazdu Inżynierów Polskich i XXVI Kongresu Techników Polskich, który odbył sie w dniach13 - 15 czerwca 2019 roku w Krakowie. Hasłem przewodnim obrad był "Inżynier Przyszłości".
-
Innowacyjne metody obróbki powierzchni płaskich na docierarkach
PublicationPrzedstawiono charakterystykę innowacyjnej technologii obróbki powierzchni płaskich i płasko-równoległych na docierarkach jedno- i dwutarczowych. Zamieszczono studium przypadku obejmującego obróbkę elementów ceramicznych i wykonanych z węglików spiekanych, analizując jakość szlifowanych powierzchni i czasochłonność operacji oraz koszty obróbki elementów płaskich w układzie dwutarczowym.
-
Influence of Parameters of Laser Beam Welding on Structure of 2205 Duplex Stainless Steel
PublicationLaser welding is used in modern industry, having many advantages comparing to traditional welding technologies. Nowadays, industry sectors such as shipbuilding, automotive and aviation can’t be imagined without laser processing technologies. Possibility of increase of welded joint properties, autogenous welding and high level of process automation makes the technology of laser welding perspective part of the industry. Physical...
-
Influence of High Temperature Oxidation on Hydrogen Absorption and Degradation of Zircaloy-2 and Zr 700 Alloys
PublicationThe present research was aimed at determining the effects of the oxide layers on hydrogen absorption, microstructure and mechanical properties of the Zircaloy- 2 and Zr 702 alloys. The oxidation was made at 350 °C, 700 °C and 900 °C for 10 to 30 min in laboratory air, followed by hydrogen cathodic charging for 72 h and annealing at 400 °C for 4 h. The slow strain rate tests were carried out on oxidized, charged and annealed specimens. The...
-
Impact of high temperature drying process on beech wood containing tension wood
PublicationThe technology of high temperature drying has a great inuence on dimensional and selected physical changes in tension wood. Article is focused on the measurement properties such as moisture content, color changes and longitudinal warping. The quality of beech wood is determined based on structure and properties of wood, frequency of defects in wood material. The tension wood is considered as an important wood defect causing negative...
-
Fabrication methods of smart composite coatings - review
PublicationPostoperative bacterial infections are one of the main reasons for unsuccessful implantation of long-term implants. The development of bacterial infection requires antibiotic therapy, in extreme cases a reimplantation procedure is necessary. In order to provide materials for implants with antibacterial properties, they are subjected to modifications to create a coating that will release the drug substance, when the inflammation...
-
Erozja Kawitacyjna Austenitycznej Stali Nierdzewnej 1.4541
PublicationProces erozji kawitacyjnej powoduje niszczenie materiału, na który składają się: odkształcenie plastyczne, ubytki masy, zmiany fazowe, fragmentacja ziaren, zmiany mikrogeometrii i makrogeometrii powierzchni. Różnorodność czynników mająca wpływ na proces niszczenia materiału sprawia, iż trudno jest przewidzieć postęp procesu niszczenia ciała stałego wskutek kawitacji. Z tego względu...
-
Electrochemical properties of porous Sr0.86Ti0.65Fe0.35O3 oxygen electrodes in solid oxide cells: Impedance study of symmetrical electrodes
PublicationThis work evaluates porous Sr0.86Ti0.65Fe0.35O3 (STF35) as a possible oxygen electrode material for Solid Oxide Cells. The powder synthesis was performed by solid state method. Characterization included DC electrical conductivity study of sintered bulk samples and impedance spectroscopy study of symmetrical electrodes deposited on gadolinium doped ceria substrates. Measurements were carried out in atmospheres with different pO2...
-
Effects of electrophoretic deposition times and nanotubular oxide surfaces on properties of the nanohydroxyapatite/nanocopper coating on the Ti13Zr13Nb alloy
PublicationLoad-bearing implants are developed with a particular emphasis placed on an application of ceramic hydroxyapatite coatings in order, to enhance the bioactivity of titanium implants and to shorten the healing time. Therefore, thin, fully crystalline coatings that are, highly adhesive, hydrophilic and demonstrating antibacterial properties are ly looked for. The aim of this research was to develop and characterize the properties...
-
Effect of the welding environment and storage time of electrodes on the diffusible hydrogen content in deposited metal
PublicationIn the study the glycerin displacement method was used for determination of diffusible hydrogen content in deposited metal. Specimens were welded in the air and in the water with covered rutile electrodes. The first part of the specimens was made immediately after opening the package of the electrodes. The electrodes were then stored in opened packages in laboratory conditions that allowed for contact with the air for three years....
-
Effect of Storage Conditions of Rutile Flux Cored Welding Wires on Properties of Welds
PublicationThe influence of storage locations of two grades of rutile flux cored welding wires on their surface condition and the strength of the welds made with them were studied. Wires were stored in real urban conditions (Gdańsk and Katowice) for 1 month, simultaneously recording changes in conditions: temperature and relative humidity of the environment. Visual tests of wires in the delivered and stored condition as well as visual and...
-
Effect of selective laser treatment on initiation of fatigue crack in the main part of an undercarriage drag strut
PublicationThis paper presents the results of material characterization and a fatigue test conducted for a laser-re-melted drag strut used in an aircraft landing gear. The drag strut was re-melted with a CO2 laser beam. Eight re-melted paths were made in the form of spiral lines along the axis of the drag strut. Next, the drag strut was subjected to variable loads on a testing machine simulating loads occurring when an aircraft lands. The...
-
Effect of aeration of antibiotic-loaded bone cement on its properties and bactericidal effectiveness
PublicationBACKGROUND: Antibiotic-loaded bone cements are now widely used in medicine. They are able to locally deliver antibiotic particles and they allow treat or protect against infection. It is assumed that the bactericidal effectiveness of bioactive bone cements depend on the parameters of its production. Hence, the aim of this study was to check the effect of aeration of bone cement before mixing the components on its properties as...
-
Determination of moisture resistance of covered electrodes according to PN-EN ISO 14372
PublicationMoisture present in the electrode covering is one of the sources of diffusible hydrogen in welded joints. In order to study the diffusible hydrogen content in deposited metal, a stand for moisturizing covered electrodes, in accordance with the PN-EN ISO 14372 standard, was built. After the stand was completed, a test of moisturizing the electrodes was carried out and measurements of the diffusible hydrogen content in deposited...