Filtry
wszystkich: 1814
wybranych: 1496
-
Katalog
Filtry wybranego katalogu
wyświetlamy 1000 najlepszych wyników Pomoc
Wyniki wyszukiwania dla: STEEL-CONCRETE SPECIMEN
-
Effect of Pin Shape on Thermal History of Aluminum-Steel Friction Stir Welded Joint: Computational Fluid Dynamic Modeling and Validation
PublikacjaThis article studied the effects of pin angle on heat generation and temperature distribution during friction stir welding (FSW) of AA1100 aluminum alloy and St-14 low carbon steel. A validated computational fluid dynamics (CFD) model was implemented to simulate the FSW process. Scanning electron microscopy (SEM) was employed in order to investigate internal materials’ flow. Simulation results revealed that the mechanical work...
-
Storage of High-Strength Steel Flux-Cored Welding Wires in Urbanized Areas
PublikacjaThe condition of the consumables is a key factor determining the waste reduction in the welding processes and the quality of the welded joint. The paper presents the results of tests of four types of fux-cored wires dedicated for welding high-strength steels, stored for 1 month and 6 months in Poland in two urbanized areas: in a large seaside city (Gdańsk) and in Warsaw, located in the center of the country. The wires were subjected...
-
Study of microstress state of P91 steel using complementary mechanical Barkhausen, magnetoacoustic emission, and X-ray diffraction techniques
PublikacjaThe paper deals with assessment of microstress state of martensite P91 steel using three complementary techniques: mechanical Barkhausen emission, magnetoacoustic emission (MAE), and X-ray diffraction (XRD) profile analysis. Magnetic coercivity Hc and microstructure were investigated with inductive magnetometry and magnetic force microscopy (MFM), respectively. Internal stress level of P91 steel was modified by heat treatment....
-
Results of acoustic emission tests of corrosion protection degree of ship steel tanks covered by means of protective coatings (Phase I)
PublikacjaThis paper presents methods and results of the 1st series of tests of acoustic emission (AE) signals, aimed at assessing degree of corrosion protection of a tank made of hull structural steel, protected by means of a protective coating combined from polyurethane layer and concrete filler. The tests were carried outin compliance with a method specially elaborated for application to the work in question. In the method were used requirements...
-
The influence of the welding environment on the properties of Tekken joints made from S355J2C+N steel
PublikacjaThere are three main methods of underwater welding: dry, wet and intermediate between them, by using the local dry chamber. Due to low costs, the most common method is the wet welding with the use of covered electrodes. Water as a welding environment carries out a lot of problems. The first is limited visibility and instability of the welding arc. The biggest problem during underwater welding is high susceptibility to cold cracking,...
-
SFEM Analysis of Beams with Scaled Lengths including Spatially Varying and Cross-Correlated Concrete Properties
PublikacjaThis paper presents the results obtained for plain concrete beams under four-point bending with spatially varying material properties. Beams of increasing length but constant depth were analyzed using the stochastic finite element method. Spatial fluctuation of a uniaxial tensile strength, fracture energy and elastic modulus was defined within cross-correlated random fields. The symmetrical Gauss probability distribution function...
-
Physicochemical properties of Mn1.45Co1.45Cu0.1O4 spinel coating deposited on the Crofer 22 H ferritic steel and exposed to high-temperature oxidation under thermal cycling conditions
PublikacjaThe Crofer 22 H ferritic steel substrate was coated with an Mn1.45Co1.45Cu0.1O4 spinel by means of electrophoresis. After high-temperature oxidation under thermal cycling conditions, the physicochemical properties of the obtained system were evaluated. During 48-h cycles that involved heating the samples up to temperatures of either 750 or 800 °C, the oxidation kinetics of both coated and unmodified steel approximately obeyed...
-
Monitoring the fracture process of concrete during splitting using integrated ultrasonic coda wave interferometry, digital image correlation and X-ray micro-computed tomography
PublikacjaThe paper deals with the continuous-time monitoring of mechanical degradation in concrete cubes under splitting. A series of experiments performed with integrated coda wave interferometry (CWI) and digital image correlation (DIC), supported with X-ray micro-computed tomography (micro-CT) is reported. DIC and micro-CT techniques were used to characterize the fracture process in detail. CWI method was proved to be effective in the...
-
Effect of Some Sulphur Additives on The Degradation of 9Cr-1Mo Steel After Its 10 Years Service in The CCR Platforming Unit
PublikacjaThe work shows the results of the tests of 9Cr-1Mo steel, which was for 10 years operated in the CCR platforming unit in Group Lotos SA in Gdańsk, and then in the laboratory was sulphidised during 166 h at a temperature of 600 °C. Sulphidation was performed in a mixture of H2-H2S gases at the vapour pressure of sulphur 4.1·10-14 atm, so the order of magnitude of vapour pressure was less than that of the dissociation pressure of...
-
Diagnosis of Damage in a Steel Tank with Self-Supported Roof through Numerical Analysis
PublikacjaThe safety of civil engineering structures is one of the most important issues of building industry. That is why the assessment of the damage-involved structural response has recently become of major concern to engineers. Among a number of different approaches to diagnosis of damage, the method of measuring the changes in natural frequencies is considered to be one of the most effective indicators of global damage. From the practical...
-
Multivariate analysis of impedance data obtained for coating systems of varying thickness applied on steel
PublikacjaElectrochemical impedance spectroscopy (EIS) has proven to be a valuable test method for the electrochemical characterization of protective coatings on metals. The common way of analysis in impedance spectroscopy is to model the impedance spectrum by means of an equivalent circuit and to extract the quantity of interest using optimization techniques. A model, corresponding to the behavior of the sample under testing, is important...
-
The effect of pre-hydrogen charging on corrosion behaviour of superduplex stainless steel welded joints
PublikacjaThe paper presents results of research undertaken to determine the influence of hydrogen on passivity and corrosion resistance of 2507 super duplex stainless steel welded joints. Butt welded joints were made with low heat input using flux corded arc welding (FCAW) method. Coupons of 5.0 x 5.0 mm were cut from the welded joints containing weld metal (WM), heat affected zone (HAZ) and parent metal (PM). Hydrogen was introduced...
-
Numerical modelling and analysis of steel specimens subjected to marine immersed corrosion and tensile load
PublikacjaThe present study develops numerical models to analyse the behaviour of steel specimens subjected to marine immersed corrosion degradation and tensile load. The finite element method with the use of the explicit dynamic solver LS-DYNA, satisfying the quasi-static conditions, is employed. Two numerical models are developed, where in the first one, the scans of surfaces gathered from corroded plate specimens are implemented directly...
-
Finite element method simulations of various cases of crash tests with N2/W4/A steel road barrier
PublikacjaThe subject of this study is performance of N2/W4/A steel road safety barrier investigated in numerical simulations. System was checked under several types of initial conditions, which were assumed basing on the TB11 and TB32 normative crash tests. The main goal of present study is to investigate the relationship between initial conditions (angle and velocity) of the impact and the severity indices (associated to the vehicle occupant) during...
-
Influence of soil–structure interaction on seismic pounding between steel frame buildings considering the effect of infill panels
PublikacjaThe present research aims to study the influence of the soil-structure interaction (SSI) and existence or absence of masonry infill panels in steel frame structures on the earthquake-induced pounding-involved response of adjacent buildings. The study was further extended to compare the pounding-involved behavior versus the independent behavior of structures without collisions, focusing much on dynamic behavior of single frames....
-
Enhancing seismic performance of steel buildings having semi-rigid connection with infill masonry walls considering soil type effects
PublikacjaUnpreventable constructional defects are the main issues in the case of steel Moment-Resisting Frames (MRFs) that mostly occur in the rigidities of beam-to-column connections. The present article aims to investigate the effects of different rigidities of structures and to propose Infill Masonry Walls (IMWs) as retrofitting strategy for the steel damaged buildings. A fault or failure to meet a certain consideration of the soil type...
-
Tubular House - Form Follows Technology, Concrete Shell Structure with Inner Thermal Insulation
PublikacjaThe aim of this paper is the theoretical analysis of the possibilities and limitations of using an unconventional technology and the original architectural form stemming from it – the building with external construction and internal insulation. In Central European climatic conditions, the traditional solution for the walls of heated buildings relies on using external thermal insulation. This stems from building physics: it prevents...
-
Experimental study on the behaviour of steel columns under seismic-induced axial impact load
PublikacjaIt has been observed during major earthquakes that the so called soft-storey failure of an upper floor of a structure results in large impact load acting on structural members of the lower storeys. It may further lead to progressive collapse of the whole structure substantially intensifying human and material losses. Therefore, the aim of this paper is to investigate experimentally the behaviour of columns under bending (observed...
-
Influence of plastic deformation on stray magnetic field distribution of soft magnetic steel sample
PublikacjaThe effect of various combinations of conditions, i.e., presence of the Earth’s magnetic field during and after deformation on the distribution of stray magnetic field of S355 steel sample, which is locally deformed, was investigated. Some of the stages of the experiment were carried out in zero magnetic field. Compensation of the Earth’s magnetic field was obtained by the application of a pair of Helmholtz coils. These coils are...
-
The effect of external load on ultrasonic wave attenuation in steel bars under bending stresses
PublikacjaThe stress state in deformed solids has a significant impact on the attenuation of an ultrasonic wave propagating through the medium. Measuring a signal with certain attenuation characteristics can therefore provide useful diagnostic information about the stress state in the structure. In this work, basic principles behind a novel attenuation-based diagnostic framework are introduced. An experimental study on steel bars under three-point...
-
The use of a two-phase Monte Carlo material model to reflect the dispersion of asphalt concrete fracture parameters
PublikacjaThe work covers comprehensive laboratory tests of semi-circular bending (SCB) of asphalt concrete samples. The results of two test series, including four and 32 SCB specimens, indicate a substantial scatter of force–deflection (F-d) histories. The numerical analysis is aimed to reflect the maximum breaking load and fracture energy of the samples, pointing out their random character. The original simulation-based fictitious Monte...
-
Instantaneous Impedance Analysis of Non-Stationary Corrosion Process: a Case Study of Carbon Steel in 1M HCl
PublikacjaThe paper concerns the problem of evaluation of stationarity of carbon steel corrosion in 1M HCl. Comparison of corrosion rate with addition of corrosion inhibitor to the reference measurement is the most often used way of evaluating inhibitor efficiency. Such an approach is valid only if corrosion rate is a stationary process. Two complementary techniques were used simultaneously: volumetric analysis of evolved hydrogen and instantaneous...
-
Effect of bending-torsion on fracture and fatigue life for 18Ni300 steel specimens produced by SLM
PublikacjaIn this study, different fracture surfaces caused by fatigue failure were generated from 18Ni300 steel produced by selective laser melting (SLM). Hollow round bars with a transverse hole were tested under bending-torsion to investigate the crack initiation mechanisms and fatigue life. Next, the post-failure fracture surfaces were examined by optical profilometer and scanning electron microscope. The focus is placed on the relationship...
-
Orientation effects on the fracture behaviour of additively manufactured stainless steel 316L subjected to high cyclic fatigue
PublikacjaIn this paper, stainless steel 316L (SS316L) bars were additively manufactured (AM) in three orientations (Z – vertical, XY – horizontal, ZX45 – midway between vertical and horizontal) by using the Laser Powder Bed Fusion Melting (LPBF-M) method. The AM specimens were subjected to load control fatigue testing under full tension and compression (R = -1) at stress amplitudes ±350, ±400 and ±450 MPa. The XY and ZX45 printing orientations...
-
"Raport z wstępnych badań własności stali trudnościeralnej 460HB",. ang "Report on preliminary tests of the properties of wear-resistant steel 460HB"
PublikacjaMikrostrukturę badanej stali trudnościeralnej 460HB stanowi drobnoziarnisty martenzyt odpuszczony, który jest właściwy dla stali konstrukcyjnych niskowęglowych, niskostopowych ulepszonych cieplnie. W przypadku blach grubych, do których zalicza się badana stal, struktura może ulec zaburzeniu, jeżeli w hutniczym procesie wytwórczym wystąpiła niejednorodność odkształcenia plastycznego i w konsekwencji tworzenie się pasm segregacyjnych,...
-
Impact of steel grade on a ship colliding with an offshore wind turbine monopile supporting structure
PublikacjaOffshore wind power is experiencing rapid development around the world. The number of installations and their size is growing. Thousands of monopile support structures with diameters of 10 m and weights of 2000 tons will be installed in the coming years. Offshore wind power installations, often located close to the shore and shipping routes, pose a new challenge to ship safety. The study analyses the damages from an accidental...
-
Evaluation of pounding effects between reinforced concrete frames subjected to far-field earthquakes in terms of damage index
PublikacjaIn this paper, three different damage indexes were used to detect nonlinear damages in two adjacent Reinforced Concrete (RC) structures considering pounding effects. 2-, 4- and 8-story benchmark RC Moment Resisting Frames (MRFs) were selected for this purpose with 60%, 75%, and 100% of minimum separation distance and also without any in-between separation gap. These structures were analyzed using the incremental dynamic analysis...
-
Hydrogen charging of nitrided steel in acid solution
PublikacjaKonstrukcyjną stal, azotowaną w wyładowaniu jarzeniowym w mieszaninie gazów o różnej zawartości N2, H2 i Ar, poddawano katodowemu nawodorowaniu w kwaśnym roztworze, imitującym przepracowany olej maszynowy. W pomiarach szybkości przenikania wodoru i ekstrakcji próżniowej określano wpływ azotowanych warstw, odpowiednio, na transport wodoru i na jego nieodwracalne pułapkowanie. W obecności niezdefektowanej warstwy kompaktowych azotków...
-
Pitting corrosion in steel and electrochemical noise intensity
PublikacjaPrzedstawiono analizę szumu elektrochemicznego, rejestrowanego w obecności korozji wżerowej. Stwierdzono korelację pomiędzy intensywnością szumu a ubytkiem mas elektrod stalowych. Rejestry szumowe rozłożone zostały na składowe częstotliwościowe za pomocą przekształcenia falkowego. Dla pewnych składowych stwierdzono silniejszą korelację z ubytkiem mas korodujących elektrod. Pasmo częstotliwościowe powyższych składowych odpowiada...
-
Pitting corrosion in steel and electrochemical noise intensity
Publikacja -
Study on the strength of laminated polyurethane-steel joints
Publikacja -
The Laser Surface Remelting of Austenitic Stainless Steel
Publikacja -
Fatigue Behaviour of Sintered Duplex Stainless Steel
Publikacja -
Grease effect on fretting wear of mild steel
PublikacjaNa stanowisku laboratoryjnym przeprowadzono badania zużycia frettingowego miękkiej stali smarowanej mineralnymi i syntetycznymi smarami zawierającymi także różne dodatki: grafit dwusiarczek molibdenu ZDDP i ditiocarbamat molibdenu, w różnych stężeniach.Badania wykazały istotny wpływ konsystencji smaru i jego właściwości smarnych na zużycie frettingowe miękkiej stali oraz zróżnicowany wpływ testowanych dodatków. Obecność smaru...
-
Protective coatings for stainless steel for SOFC applications
PublikacjaW pracy przedstawiono badania związane z warstwami antykorozyjnymi stali nierdzewnych stosowanych w tlenkowych ogniwach paliwowych. Warstwy przygotowana z użyciem prekursorów polimerowych na bazie Y i Co. Użyta stal to Crofer 22 APU.
-
Fatigue life of steel, laser welded panels
PublikacjaW publikacji przedstawiono zagadnienia dotyczące możliwości analizy trwałości zmęczeniowej stalowyxh paneli spawanych laserowo typu sandwich. Przedstawiono wyniki badań laboratoryjnych w skali naturalnej a także krzywe projektowe uzyskane na podstawie systematycznych badań połączeń elementarnych spawanych laserowo. Na podstawie przedstawionych i uogólnionych wyników pokazano propozycję metodyki szacowania trwałości zmęczeniowej...
-
Analysis of wave propagation in a bolted steel joint
PublikacjaThe paper presents results of numerical and experimental investigations of elastic wave propagation in a bolted single-lap joint. The research was carried out for both symmetric and antisymmetric Lamb wave modes. In experimental studies the PZT transducers were used to excite and register wave propagation signals. The controlled value of the torque during measurements was ensured by the use of high precision torque wrenches. Numerical...
-
Buckling analysis of cold formed steel column
PublikacjaW pracy przedstawiono analizę słupa zimnogiętego o przekroju otwartym. Przeprowadzono analizy statyczne liniowe i nieliniowe. Analizowano wpływ podłoża sprężystego oraz sztywność połączenia dwóch sąsiednich słupów.
-
Influence of PWHT Parameters on the Mechanical Properties and Microstructural Behavior of Multi-Pass GTAW Joints of P92 Steel
PublikacjaThe 9% Cr steels were developed for ultra-supercritical (USC) power plants to meet the requirements of high operating temperature and pressure. These steels are produced to operate at high temperatures where impact toughness is not a concern; however, it becomes important for the welded joints to have good impact toughness at room temperature for manufacturing. The present work investigates the effect of the post-weld heat treatment...
-
Parameter estimation of a discrete model of a reinforced concrete slab
Publikacja -
The influence of polypropylene fibres on the properties of fresh and hardened concrete
Publikacja -
Experimental investigations of concrete dowels in composite floor system
PublikacjaOpisano nowy system stropow zespolonych umozliwiajacych montaz instalacji klimatyzacyjnych, wentylacyjnych i grzewczych w przestrzeni pomiedzy dwoma plytami betonowymi konstrukcji stropu: gorna i dolna. Obie plyty polaczone sa wzajemnie srodnikami stalowymi z wycieciami u gory i na dole w ksztalcie 'puzzle', ktore we wspolpracy z plyta betonowa tworza tzw. dyble betonowe. Wykonano badania laboratoryjne typu 'Push-out' tych polaczen...
-
Mathematical Description of Sorption Isotherms of Autoclaved Aerated Concrete
Publikacja -
Experimental study of the post tensioned prestressed concrete corbels
PublikacjaThe results of experimental investigation of 6 symmetrical double prestressed corbels of variable shear span to depth ratio and variable location of prestressing bars are presented in the paper. The post ten- sioned corbels were prestressed with Macalloy 1030 bars of 25 mm in diameter. The results of the tests were compared with the cracking and load carrying capacity of corbels reinforced with passive reinforce- ment. As a result...
-
Numerical mesoscopic analysis of fracture in fine-grained concrete
PublikacjaArtykuł omawia wyniki analizy mezoskopowej procesu pękania w betonie podczas zginania. Obliczenia wykonano na poziomie mezo wykorzystując model degradacji sztywności z nielokalnym osłabieniem. Zbadano wpływ właściwości kruszywa, stref przejściowych, nacięcia oraz długości charakterystycznej mikrostruktury na zachowanie sie betonu.
-
3D DEM simulations of fracture in reinforced concrete beams
PublikacjaArtykuł dotyczy zachowania się belki żelbetowej bez zbrojenia pionowego przy trzypunktowym zginaniu. Belka uległa zniszczeniu wskutek ścinania z powodu obecności nadmiernego zbrojenia podłużnego. Eksperymenty przeprowadzono w skali laboratoryjnej z wykorzystaniem systemu mikro-CT, a następnie odtworzono je w analizach numerycznych stosując metodą elementów dyskretnych 3D (DEM). Zastosowano 4-fazowy model betonu z mezostrukturą,...
-
Modelling of concrete behaviour in uniaxial compression and tension with DEM.
PublikacjaW artykule omowiono wyniki modelowania betonu podczas jednoosiowego sciskania i rozciagania stosujac metode elementów dyskretnych. Beton zostal opisany jako material 3-fazowy (kruszywo, zaprawa cementowa i strefy kontaktu). Szczegolna uwage zwrocono na zjawiska mikro-strukturalne na poziomie kruszywa (lancuchy sil, wiry, obroty ziaren). Wyniki numeryczne zostaly porownano z wynikami badan doswiadczalnych.
-
Modelling of concrete using lattice and discrete element method
PublikacjaModelowanie betonu przy zastosowaniu metody siatkowej i metody elementów dyskretnych.
-
Cyclic deformation and fracture behaviour of additive manufactured maraging steel under variable-amplitude loading
PublikacjaThe cyclic deformation and fracture behaviour of 18Ni300 maraging steel produced by laser beam powder bed fusion is studied under variable-amplitude loading. The tests were conducted under fully-reversed strain-controlled conditions with a loading sequence comprising three ascending cycles and three descending cycles repeated sequentially until failure. After the tests, fracture surfaces were examined using height and volume surface...
-
On the Possibility of Improving the Oxidation Resistance of High-Chromium Ferritic Stainless Steel Using Reactive Element Oxide Nanoparticles
PublikacjaHigh-chromium ferritic steels are current the only viable candidates for cheap interconnect materials for application in high-temperature solid oxide fuel and electrolyzer cells (HT-SOFCs/SOECs). The durability and operating characteristics of interconnects manufactured using these materials may be improved significantly by applying a protective-conducting MoCo2O4 coating and depositing an intermediate layer consisting of nanoparticles...
-
Influence of metallic porous microlayer on pressure drop and heat transfer of stainless steel plate heat exchanger
PublikacjaThe experimental analysis of passive heat transfer intensification in the case of plate heat exchanger has been carried out. On the heat transfer surface of heat exchanger the metallic porous layer was created. The experiment was accomplished in two stages. In the first stage the commercial stainless steel gasketed plate heat exchanger was investigated, while in the second one – the identical heat exchanger but with the modified...
-
Effect of plasma sprayed and laser re-melted Al2O3 coatings on hardness and wear properties of stainless steel
PublikacjaCommercially available austenic stainless steel substrate was coated with commercially available, raw Al2O3 powder applied by means of plasma spraying method and then re-melted with CO2 laser beam of various parameters. Tribological and mechanical properties of the 120 J/mm and 160 J/mm laser re-melted coatings were compared with the tribological and mechanical properties of the “as-sprayed” coating. The influence of the laser...
-
Simulations of high-pressure fluid flow in a pre-cracked rock specimen composed of densely packed bonded spheres using a 3D CFD model and simplified 2D coupled CFD-DEM approach
PublikacjaW artykule zastosowano dwa różne podejścia do opisu jednofazowego przepływu płynu w wstępnie spękanej próbce skały o niskiej porowatości pod wysokim ciśnieniem. Głównym celem pracy było bezpośrednie porównanie rozkładu ciśnień, gęstości i prędkości płynów we wstępnie pękniętej próbce. Zachowanie próbki imitującej skałę zostało opisane przez gęsto upakowane połączone kohezją kulki z nakładającymi się na siebie elementami. Pierwsze...
-
Induction Assisted Hybrid Friction Stir Welding of Dissimilar Materials AA5052 Aluminium Alloy and X12Cr13 Stainless Steel
PublikacjaThis research aimed to study the induction in-situ heated hybrid friction stir welding (IAFSW) method to join AA5052 aluminium alloy with X12Cr13 stainless steel (SS) to enhance joint strength. The potency of this method on the mechanical properties and microstructural characterizations were also investigated. The results show that the transverse tensile strength gained was 94% of the AA5052 base metal that is 229.5 MPa. This superior...
-
A constitutive model for concrete based on continuum theory with non-local softening coupled with eXtended Finite Element Method. Computational Modelling of Concrete Structures,
PublikacjaArtykuł omawia model połączony ciągły-nieciągły do modelowania stref lokalizacji i rys w betonie niezbrojonym. Obliczenia wykonano stosując rozszerzoną metodę elementów skończonych. Wyniki numeryczne porównano z doświadczeniami.
-
Influence of metallic porous microlayer on pressure drop and heat transfer of stainless steel plate heat exchanger
PublikacjaThe experimental analysis of passive heat transfer intensification in the case of plate heat exchanger has been carried out. The metallic porous layer was created on the heat transfer surface of analyzed unit. The experiment was accomplished in two stages. In the first stage the commercial stainless steel gasketed plate heat exchanger was investigated, while in the second one – the identical heat exchanger but with the modified...
-
Badania eksperymentalne modelu zbiornika stalowego na stole sejsmicznym = Experimental study on steel tank model using shaking table
PublikacjaCylindrical steel tanks are very popular structures used for storage of products of chemical and petroleum industries. Their safety and reliability is really crucial because any failure may have serious consequences. Earthquakes are the most dangerous and also the most unpredictable dynamic loads acting on such structures. On the other hand, rockburst-induced ground motions are usually considered to be less severe due to lower...
-
Experimental and analytical thermal study of PTFE composite sliding against high carbon steel as a function of the surface roughness, sliding velocity and applied load
PublikacjaThis study investigates the contact temperatures caused by frictional heating of sliding parallel pairs. In this case the materials studied are a PTFE composite in contact with a high carbon steel plate. These materials are commonly used for industrial applications, in particular as the main contacting components within a scroll expander system. The expected contact temperature values are important to be quantified in order to...
-
Stability of cylindrical steel silos composed of corrugated sheets and columns based on FE analyses versus Eurocode 3 approach
PublikacjaComprehensive static and dynamic 3D stability finite element analyses of a cylindrical steel silo composed of corrugated sheets and open thin-walled vertical stiffener profiles were carried out by taking the geometric and material non-linearity into account. The silowas subjected to axisymmetric and non-axisymmetric loads imposed by a bulk solid following Eurocode 1. Theoretical and measured initial geometric imperfections were...
-
Qualification of brazing procedure for furnace brazing of austenitic steel according to requirements of the ASME BPVC section IX
PublikacjaThe article presents the procedure for qualifying brazing technology in a vacuum furnace on the example of stainless steel elements joined with copper filler material from the F-No group. 105, in accordance with the ASME Sec. IX, part QB (ASME Boiler and Pressure Vessel Code. Qualification Standard for Welding, Brazing and Fusing; Procedures; Welders; Brazers; and Welding, Brazing and Fusing Operators). The essential variables...
-
Performance of Vector-valued Intensity Measures for Estimating Residual Drift of Steel MRFs with Viscous Dampers
PublikacjaViscous Dampers (VDs) are widely used as passive energy dissipation system for improving seismic performance levels especially in retrofitting of buildings. Residual Inter-story Drift Ratio (R-IDR) is another important factor that specifies the condition of building after earthquake. The values of R-IDR illustrates the possibility of retrofitting and repairing of a building. Therefore, this study aims to explore the vector-valued...
-
The abrasive wear resistance of coatings manufactured on high-strength low-alloy (HSLA) offshore steel in wet welding conditions
PublikacjaSome marine and offshore structure elements exploited in the water cannot be brought to the surface of the water as this will generate high costs, and for this reason, they require in-situ repairs. One of the repair techniques used in underwater pad welding conditions is a wet welding method. This paper presents an investigation of the abrasive wear resistance of coatings made in wet welding conditions with the use of two grades...
-
Electrical mapping of AISI 304 stainless steel subjected to intergranular corrosion performed by means of AFM-LIS in the contact mode
PublikacjaThe paper presents results of the AFM-based approach to local impedance spectroscopy (LIS) measurements performed in a 20 20 lm grid within an austenite grain–grain boundary region for sensitized AISI 304 stainless steel (SS). Maps of electrical parameters obtained on the basis of localized impedance spectra were demonstrated, presenting their changes and correlation with the sample topography. Performed research revealed significant...
-
Study of a Multicriterion Decision-Making Approach to the MQL Turning of AISI 304 Steel Using Hybrid Nanocutting Fluid
PublikacjaThe enormous use of cutting fluid in machining leads to an increase in machining costs, along with different health hazards. Cutting fluid can be used efficiently using the MQL (minimum quantity lubrication) method, which aids in improving the machining performance. This paper contains multiple responses, namely, force, surface roughness, and temperature, so there arises a need for a multicriteria optimization technique. Therefore,...
-
Modification of cement-ash composites with steel fibre addition
PublikacjaPraca zawiera wyniki badań kompozytów cementowo-popiołowych, w których popiół zastosowano jako częściowy zamiennik cementu. Do kompozytów dodano niewielkie ilości dwóch rodzajów włókien stalowych. Zbadano właściwości techniczne kompozytów. Wytrzymałości kompozytów cementowo-popiołowych z włóknami stalowymi w stosunku do wytrzymałości kompozytów bez włókien po wszystkich okresach wiązania i twardnienia były wyższe od kilku do kilkudziesięciu...
-
Fatigue properties of laser welded steel sandwich panel.
PublikacjaPrzedstawiono wyniki badań laboratoryjnych paneli SANDWICH, prowadzonych w Kat. TOiOO Wydz. OiO na konstrukcjach w skali rzeczywistej. Przedstawiono program badań, omówiono założenia procedur badawczych i konstrukcję stanowisk testowych. Dokonano porównania uzyskanych rezultatów z wynikami prezentowanymi w literaturze. Przedstawiono propozycję algorytmu szacowania trwałości zmęczeniowej konstrukcji spawanych laserowo.
-
The effect of the concentration of steel fibres on the properties of industrial floors
Publikacja -
Evaluation of 316L porous stainless steel for SOFC support
PublikacjaW pracy przedstawiono wyniki badań stali typu 316L związanych z zastosowaniem w tlenowych ogniwach paliwowych.
-
The influence of dimensional accuracy on steel structures cost calculation
PublikacjaW referacie przedstawiono zależność pomiędzy wartością tolerancji a kosztami wytwarzania budowlanych konstrukcji stalowych. Opisano zasady klasyfikacji tolerancji prętowych konstrukcji stalowych z uwagi na porawny montaż konstrukcji wyrażony równaiem pętli montażowej. Przedstawiono podstawy analizy i syntezy tolerancji oraz zaproponowano nową formułę optymalizacji kosztów wytwarzania. Wskazano metody rozwiązania zadania optymalizacyjnego.
-
Selected problems on application of steel sandwich panels to marine
PublikacjaW pracy przedstawiono wybrane problemy stosowania stalowych laserowo spawanych paneli w konstrukcji statku. Problemy te wynikają ze specyfiki cienkiej, spawanej laserowo konstrukcji stalowej i obejmują szerokie spektrum zagadnień począwszy od własności wytrzymałościowychy elementarnego połączenia teowego spawanego laserowo poprzez łączenie paneli ze sobą a skończywszy na integracji paneli z konstrukcją tradycyjną.
-
Practical Application of the Industry 4.0 Concept in a Steel Company
Publikacja -
Heat tint colours on stainless steel and welded joints
PublikacjaSurface layer condition of stainless steels and welded joints influences strongly their corrosion resistance. This problem seems to be underestimated. This current study explains the phenomenon of heat tint forming on welds, the methods of its removal, inspection procedures after heat tint removing and post weld finishing
-
Simultaneous impedance and volumetric studies and additionally potentiodynamic polarization measurements of molasses as a carbon steel corrosion inhibitor in 1M hydrochloric acid solution
PublikacjaThe inhibition effect of molasses on the corrosion of low carbon steel in 1M hydrochloric acid solution was investigated by volumetric and electrochemical measurements. Potentiodynamic polarization and dynamic electrochemical impedance spectroscopy (DEIS) results were obtained and compared with to those, obtained with the hydrogen evolution technique. All results indicate that molasses functioned as a good inhibitor in 1M hydrochloric...
-
Fibres from recycled post-consumer tyres for concrete reinforcement
PublikacjaW pracy przedstawiono aktualną sytuację dot. wykorzystania drutu stalowego z recyklingu opon samochodowych. Przedstawiono wyniki badań przeprowadzonych w laboratorium Katedry Konstrukcji Betonowych i Technologii Betonu nad zastosowaniem włókien stalowych z recyklingu do zbrojenia betonu. Otrzymane wyniki porównano z próbkami fibrobetonu uzyskanego na bazie przemysłowo produkowanych włókien stalowych.
-
Static and dynamic concrete calculations: Breakable aggregates in DEM model
PublikacjaThe paper deals with the calculations of a 3-point bending beam under static and dynamic loads. The real microstructure was obtained from laboratory tests using micro-tomography images. The quasi-static results were compared directly with experimental data at both macro and micro levels. Subsequently, higher strain rates were applied to investigate dynamic effects. The study focused on the influence of dynamic loading on the macroscopic...
-
An efficient and robust method for predicting asphalt concrete dynamic modulus
Publikacja -
Concrete corrosion against penetration of mineral oil application of impregnants
PublikacjaOleje stanowią związki organiczne, w skład których wchodzą kwasy tłuszczowe nasycone i nienasycone oraz gliceryny różnego rodzaju. W zależności od rodzaju i właściwości olejów agresywność ich w stosunku do betonu jest różna. Olej izoluje dostęp wody do składników betonu, dlatego nie następuje dalsza hydratacja i przyrost wytrzymałości. Przesycenie betonu olejami powoduje wskutek obniżenia tarcia wewnętrznego tworzywa obniżenie...
-
Computational modelling of concrete behaviour under static and dynamic conditions
Publikacja -
Properties of Composite Modified with Limestone Powder for 3D Concrete Printing
Publikacja -
Environmentally friendly material solutions in the technology of autoclaved aerated concrete
Publikacja -
Effect of perlite waste addition on the properties of autoclaved aerated concrete
Publikacja -
Simulations of fracture in concrete elements using continuous and discontinuous models
PublikacjaArtykuł przedstawia wyniki symulacji MES w elementach betonowych przy zastosowaniu modeli ciągłych i nieciągłych. Stosując modele ciągłe symulowano proces lokalizacji odkształceń. Stosując modele nieciągłe symulowano proces zarysowania. Obliczenia wykonano dla różnych typów obciążeń.
-
Stress strain relations and modulus of elascity of two stage concrete.
PublikacjaOmówiono badania doświadczalne przeprowadzone dla betonu dwuetapowego. Beton wykonano z trzech różnych kruszyw przy zastosowaniu trzech różnych proporcji w/c i c/p. Wyznaczono związki pomiędzy naprężeniami i odkształceniami. Na drodze statystycznej opracowano wzory umożliwiające wstępne szacowanie wartości siecznego modułu Younga. Ponieważ metoda dwuetapowa pozwala na zachowanie kontaktu pomiędzy poszczególnymi elementami kamiennego...
-
A 3D lattice model to describe fracture process in fibrous concrete
PublikacjaArtykuł omawia wyniki modelowania procesu zarysowania w elementach betonowych zawierające stalowe włókna przy zastosowaniu dyskretnego modelu kratownicowego. Beton był modelowany na poziomie mezoskali z uwzględnieniem 5 faz: kruszywa, zaczynu cementowego, włókien i obu stref kontaktu. Obliczenia trójwymiarowe wykonano dla jednoosiowego rozciągania.
-
FE analysis of reinforced concrete corbels with enhanced continuum models
PublikacjaW artykule pokazano wyniki MES symulacji wsporników żelbetowych. Zachowanie wsporników modelowano przy zastosowaniu 3 różnych modeli betonu: sprężysto-plastycznego, degradacji sprężystej i rozmytych rys. Modele rozszerzono o długość mikrostruktury przy zastosowaniu teorii nielokalnej. Wyniki numeryczne porównano z doświadczeniami z literatury.
-
Computational modelling of concrete behavior under static and dynamic conditions
PublikacjaW artykule zaproponowano wyniki obliczeń MES dla betonu podczas dynamicznego obciążenia. Przyjęto model sprężysto-plastyczno-lepki z nielokalnym osłabieniem. Obliczenia MES dla elementów betonowych pod obciążeniem dynamicznym o różnej prędkości obciążenia porównano bezpośrednio z doświadczeniami.
-
Modelling of fracture process in concrete using a novel lattice model.
PublikacjaArtykuł omawia wyniki modelowania procesu zarysowania w elementach betonowych przy zastosowaniu dyskretnego modelu kratownicowego. Beton był modelowany na poziomie mezoskali z uwzględnieniem 3 faz: kruszywa, zaczynu cementowego i stref kontaktu. Obliczenia wykonano dla rozciągania i ścinania połączonego z rozciąganiem.
-
DEM ANALYSIS OF EFFECT OF INTERFACIAL TRANSITIONAL ZONES ON FRACTURE IN CONCRETE.
PublikacjaArtykuł omawia wyniki numeryczne dotyczące pękania betonu uzyskane stosując metodę elementów dyskretnych. Trójwymiarowe obliczenia wykonano dla próbek betonowych podczas zginania. Beton został opisany jako model 4-fazowy. Mikrostrukturę betonu przyjęto na podstawie 3D zdjęć mikro-tomograficznych. Zbadano wpływ stref przejściowych na wytrzymałość i proces pękania. Wyniki numeryczne zostały porównane z wynikami doświadczalnymi. Uzyskano...
-
Study of fracture process in concrete using a discrete lattice model.
PublikacjaW artykule omówiono wyniki numeryczne z zastosowaniem dyskretnego modelu rusztowego złożonego z belek do symulacji procesu zarysowania w elementach betonowych. Obliczenia wykonano dla różnych procesów obciążeniowych. Wyniki porównano jakościowo z wynikami doświadczeń.
-
Modelling of concrete behaviour with a non-local continuum damage approach
PublikacjaW artykule przedstawiono wyniki numerycznej dla różnych problemów brzegowych związanych z powstawaniem rys w betonie. Obliczenia wykonano przy zastosowaniu modelu zniszczeniowego (z uwzględnieniem degradacji sztywności). Do opisu rys, model rozszerzono o nielokalność.
-
Non-Destructive Testing of the Longest Span Soil-Steel Bridge in Europe—Field Measurements and FEM Calculations
PublikacjaThe article describes interdisciplinary and comprehensive non-destructive diagnostic tests of final bridge inspection and acceptance proposed for a soil-steel bridge made of corrugated sheets, being the European span length record holder (25.74 m). As an effect of an original concept a detailed and precise information about the structure short-term response was collected. Periodic diagnostics of bridge deformations was done one...
-
Fracture Surface Topography Parameters for S235JR Steel Adhesive Joints After Fatigue Shear Testing
PublikacjaThis paper presents the experimental results of a study investigating the effect of holes and notches made on the overlap ends on the strength of adhesive joints. Single-lap joints made of S235JR steel sheets bonded with Araldite 2024-2 epoxy adhesive were tested. For comparative reasons, static shear strength tests and high-cycle fatigue strength tests were performed. Adhesive-filled joints having three holes, each with a diameter...
-
A coupled constitutive model for fracture in plain concrete based on continuum theory with non-local softening and eXtended Finite Element Method
PublikacjaThe paper presents a constitutive model for concrete which combines a continuous and discontinuous fracture description. In a continuum regime, two different constitutive laws were used. First, a plasticity model with a Rankine failure criterion and an associated fl ow rule was used. Second, a constitutive law based on isotropic damage mechanics was formulated. In order to capture the width of a localized zone and to obtain mesh-independent...
-
Microstructure and corrosion behaviour of carbon steel and ferritic and austenitic stainless steels in NaCl solutions and the effect of p-nitrophenyl phosphate disodium salt
PublikacjaThe microstructure and corrosion behavior of carbon steel (CSA516) and ferritic (SS410) and austenitic (SS304L) stainless steels were studied and compared. Corrosion tests were carried out in 0.5 M NaCl solutions. Rates of corrosion were monitored based on weight loss, Tafel extrapolation and linear polarization resistance (LPR) methods. Rates of corrosion were ranked following the order: CSA516 >> SS410 > SS304L. The impact of...
-
Studies of the mechanism of metal metal dusting of 10CrMo9-10 steel after 10 years of operation in trhe semi-regenerative catalytic reformer
PublikacjaThe study showed that metal dusting mechanism of 10CrMo9-10 steel operated in industrial environment differs from models developed in laboratories. Significant differences lie in the fact that the models developed in laboratories only assume the formation of metastable carbide M3C, while studies have shown that the formation of M3C carbides is associated with the transformation of primary carbides and in the next stage is preceded...
-
Analysis of the possibility of creep damage detection in T24 heat resistant steel with the help of magnetic nondestestructive testing methods
PublikacjaThe paper presents the result of an analysis of applicability of various electromagnetic methods of nondestructive evaluation for creep damage detection in a novel heat resistant steel - T24 grade. Two sample sets, cut out from membrane wall tubes, were investigated – the as-delivered one and another exploited for 36,000 h in a power plant. There are described results of magnetic hysteresis loops B(H), Barkhausen noise (BN) and...
-
Damage imaging algorithm for non-destructive inspection of CFRP/steel adhesive joints based on ultrasonic guided wave propagation
PublikacjaThe paper concerns assessing the quality of the adhesive connection between a steel plate and the reinforcing CFRP laminate. A three-stage algorithm for non-destructive damage imaging was developed. As the first step, an initial study involving dispersion curves of joint components was executed to determine the material parameters and the appropriate excitation frequency. During the second step, damage identification in three-layer...
-
A brief note on entire fracture surface topography parameters for 18Ni300 maraging steel produced by LB-PBF after LCF
PublikacjaThe concept of entire fracture surface investigation is helpful in explaining fatigue phenomena. In this paper, this method has been applied for 18Ni300 maraging steel using a 3D measurement system. Before post-mortem analysis, the specimens produced by laser beam powder bed fusion (LB-PBF) were tested under low-cycle fatigue (LCF) for eight strain amplitudes in the interval 0.3% to 1.0%. The attention was placed on the relationship...
-
Tribological Properties of Thermoplastic Materials Formed by 3D Printing by FDM Process
PublikacjaThe dataset entitled 3D printed ABS thermoplastic vs. steel. Dry sliding wear test in constant load & velocity ring on flat configuration. Test parameters: print layer thickness and orientation. Test symbol: 019_h_4 contains: the time base (expressed in seconds and minutes), the friction torque for sliding friction, rotational velocity of the counter – specimen (velocity of sliding), friction coefficient, load in the friction contact...
-
6.2, Engineering structures. [Chapter] 6.2.1, Assessment of the technical condition and repairs to cylindrical tank : 6.2.2, Assessment and repair of underground arterial pipelines : 6.2.4, Assessment and repair of steel chimneys
PublikacjaJerzy Ziółko opracował następujące fragmenty książki: w rozdziale 6.2. Engineering structures (Obiekty inżynierskie), pkt. 6.2.1 Assessment of the technical condition and repairs to cylindrical tank (Diagnostyka stanu technicznego i naprawy zbiorników walcowych), pkt. 6.2.2 Assessment and repair of underground arterial pipelines (Diagnostyka i naprawy podziemnych rurociągów magistralnych, pkt. 6.2.4 Assessment and repair of steel...