Wyniki wyszukiwania dla: dimensionless slip-length
-
NUMERICAL SIMULATION OF CRATER CREATING PROCESS IN DYNAMIC REPLACEMENT METHOD BY SMOOTH PARTICLE HYDRODYNAMICS
PublikacjaA theoretical base of SPH method, including the governing equations, discussion of importance of the smoothing function length, contact formulation, boundary treatment and finally utilization in hydrocode simulations are presented. An application of SPH to a real case of large penetrations (crater creating) into the soil caused by falling mass in Dynamic Replacement Method is discussed. An influence of particles spacing on method...
-
A walk Around Gdańsk for Physicists
PublikacjaI provide a guide to Gdańsk (Danzig) and some of its suburbs, focusing on sites of particular interest to physicists. These include the Town Hall with the old Gdańsk standards of length at its entrance, the solar dial of 1588 on its corner, and its bell tower; the Naturalists Society; the medieval harbor crane; the medieval astronomical clock in St. Mary's Church; the late nineteenth-century lighthouse and time ball; and sites...
-
Diffusible hydrogen management in underwater wet self-shielded flux cored arc welding
PublikacjaThis article reports the effect of underwater wet welding parameters and conditions on the diffusible hydrogen content in deposited metal for welding with a self-shielded flux cored wire. The diffusible hydrogen content in deposited metal was determined using the glycerin method according to the Plackett-Burman design determining the significance of the effect of the stick out length, welding current, arc voltage, travel speed...
-
Pylon foundation of a cable stayed bridge at the motorway ring road of Wrocław
PublikacjaThe largest bridge of the motorway ring road of Wroclaw is a cable stayed bridge over the Odra river near Rędzin. Due to hydrogeological conditions of the ground it was not convenient to use standard bored piles of high length. Instead shorter piles were applied with additional improvement by cement injections at the pile toes. This decision was possible by extending ground investigation program and application of numerical modeling...
-
Stress analysis of a strip under tension with a circular hole
PublikacjaThe paper addresses stress analysis of a strip with a circular hole under uniform uniaxial tension based oncircumferential stress expressionρπ. Stresses are analyzed in the infinite-length strips under tension with holes, the ratioof the hole radiusa to the strip half-widthb is either equal to:κ =a/b = 0.1 orκ = 0.5. Circumferential stresses aredetermined in selected cross-sections of the strip. The stress diagrams display local...
-
Finite-window RLS algorithms
PublikacjaTwo recursive least-squares (RLS) adaptive filtering algorithms are most often used in practice, the exponential and sliding (rectangular) window RLS algorithms. This popularity is mainly due to existence of low-complexity versions of these algorithms. However, these two windows are not always the best choice for identification of fast time-varying systems, when the identification performance is most important. In this paper, we...
-
OCENA WŁAŚCIWOŚCI ROZLEGŁYCH SYSTEMÓW UZIEMIEŃ PRACUJĄCYCH W UKŁADACH OCHRONY ODGROMOWEJ
PublikacjaW wyniku połączenia wszystkich elementów uziemionych w obiekcie budowlanym do szyny ekwipotencjalnej powstaje często bardzo rozległy system uziemień. Ocena tak rozległego systemu za pomocą metod wykorzystujących przebiegi wolnozmienne prowadzi do zbyt optymistycznych wniosków odnośnie do ich właściwości podczas odprowadzania prądów wyładowań atmosferycznych. Pomiary z zastosowaniem metody wykorzystującej przebiegi impulsowe pomiaru...
-
ASPEKTY BEZPIECZEŃSTWA W OCENIE WYNIKÓW POMIARÓW UZIEMIEŃ ODGROMOWYCH
PublikacjaOcena rozległego systemu za pomocą metod wykorzystujących przebiegi wolnozmienne prowadzi do zbyt optymistycznych wniosków odnośnie ich właściwości podczas odprowadzania prądów wyładowań atmosferycznych. Bardziej bezpieczne wnioski powstają w wyniku pomiarów z zastosowaniem metody wykorzystującej przebiegi impulsowe, ponieważ wtedy jest uwzględniana tylko ta część nawet bardzo rozległego systemu uziemień, która bierze udział w...
-
Adenocarcinoma, metastatic, NOS - Female, 76 - Tissue image [408073001064341]
Dane BadawczeThis is the histopathological image of STOMACH tissue sample obtained in Medical University Gdańsk and deposited in ZMDL-GUMED. The sample image was taken using: VS200 Olympus slide scanner (20x magnification) and saved to DICOM format.
-
Ichtiofauna seasonal changes in Redłowo area
Dane BadawczeSallow water areas of the Baltic Sea are very important feeding, spawning, and nursery grounds for many fish species. The dataset includes data from fish mass analysis and detailed analysis. The mass analysis includes total abundance and a total weight of fish species caught during sampling. Detailed analysis includes individual fish total length, weight,...
-
Complex modulus of Cement Bitumen Treated Material Mixture C3E4 laboratory mixed/laboratory compacted (7-365 days of curing at 20C)
Dane BadawczeDataset presents data of complex modulus determined for cold recycled mixture – cement bitumen treated material mixture with following binding agents: 3% cement, 4% emulsion (C3E4). Mixture was designed according to Polish requirements for the base course of pavement. Mixture was mixed in laboratory conditions on the basis of materials obtained from...
-
Complex modulus of Cement Bitumen Treated Material Mixture C3E4 field mixed/laboratory compacted (7-365 days of curing at 20C)
Dane BadawczeDataset presents data of complex modulus determined for cold recycled mixture – cement bitumen treated material mixture with following binding agents: 3% cement, 4% emulsion (C3E4). Mixture was designed according to Polish requirements for the base course of pavement. Mixture was mixed in the field conditions and later compacted in laboratory. Mixture...
-
Wave propagation signals for ultrasonic tomography of concrete during splitting
Dane BadawczeThe DataSet contains the results of the mechanical behaviour of a concrete cube with dimensions 70 x 70 x 70 cm3under the splitting test. Three cubes were tested: cube 1 (concrete with polymer fibres), cube 2 (concrete with steel fibres) and cube 3 (plain concrete).
-
Environmental aspects of shale gas recovery in Baltic Basin
PublikacjaFactors limiting shale gas exploration and exploitation in Pomorskie Voivodeship are presented. In particular, ground and surface water availability and land/community impact is discussed. Production from unconventional reservoirs requires proper well completion through hydraulic fracturing, hence voluminous streams of water are needed – in total 8000 to 20000 m3 per 1000 m of borehole length. 17 major groundwater basins were characterized....
-
Fiber optic low-coherence Fabry-Pérot interferometer with ZnO layers in transmission and reflective mode: comparative study
PublikacjaA construction of a low-coherence fiber-optic Fabry-Pérot interferometer using a thin ZnO layer as a reflective surfaces was proposed and examined. In the investigated setup, the ZnO layer of thickness 200 nm were deposited on the face of the standard telecommunication single-mode optical fiber (SMF-28). Measurements of interference signal were performed for the interferometer working in the transmission and reflective mode, as...
-
Reconstruction of 3D structure of positive corona streamer by local methods
PublikacjaThe computer algorithms were used for reconstruction of streamer 3D structure. We propose the 3D tree structure model of corona discharge streamer composed with nodes and edges between chosen couples of nodes, which enables easy computation of some important parameters ofstreamers. The 3D model can be derived directly from two projection images by global methods like evolutionary searching or particle simulations. In this paper...
-
A ROLE PLAYING GAME NAME GENERATOR LEARNING ITS CREATIVITY FROM ARKADIA MUD PLAYERS
PublikacjaThe paper proposes an approach to creative generation of new names for the purposes of Role Playing Games in fantasy realms. The generator based on an existing database of na mes is able to propose a set of new names with regard to demanded attributes, such as: length of the name, sex and race of the character, a given p hrase as the origin for the generated name as well as subjective evaluations from former users. The software...
-
Rigid finite elements and multibody modelling used in estimation and reduction of rod vibrations
PublikacjaIn the paper, a mechanical set composed of a robot (manipulator) and of an elastic beam is considered. The beam is fixed to the top of the robot structure. In most of the similar cases, undesired vibrations can be excited in the beam. They are especially significant, when dynamics in the robot braking period is examined. In the paper, estimation and modification of length of the braking period is proposed, in order to reduce the...
-
Ontologies vs. Rules — Comparison of Methods of Knowledge Representation Based on the Example of IT Services Management
PublikacjaThis text provides a brief overview of selected structures aimed at knowledge representation in the form of ontologies based on description logic and aims at comparing them with their counterparts based on the rule-based approach. Due to the limitations on the length of the article, only elements associated with the representation of concepts could be shown, without including roles. The formalisms of the OWL language were used...
-
Chemical Vapor Transport Route toward Black Phosphorus Nanobelts and Nanoribbons
PublikacjaChemical vapor transport (CVT) method is widely used for bulk black phosphorus (BP) fabrication. In this work, we demonstrate that CVT provides a route for the fabrication of BP nanoribbons and nanobelts. This method consists of a two-step procedure, including initial BP column growth using the CVT technique, followed by ultrasonic treatment and centrifugation. The obtained nanostructures preserve BP column dimensions, forming...
-
Efficiency of service recovery in scale-free optical networks under multiple node failures
PublikacjaIn this paper we examine the properties of scale-free networks in case of simultaneous failures of two networknodes. Survivability assumptions are as follows: end-to-end path protection with two node-disjoint backup pathsfor each working path. We investigate three models of scale-free networks generation: IG, PFP and BA.Simulations were to measure the lengths of active and backup paths and the values of service recovery time.We...
-
Construction of phylogenetic trees with topological constraints
PublikacjaThis paper proposes a method of reconstruction of phylogenetic trees based on heuristic search with topological constraints. Using topological constraints it is possible to reduce the set of solutions as well as to enforce that the result is consistent with a given hypothesis about the evolution process within some group of species. Along with this work a number of algorithms used for phylogenetic analysis were implemented. Those...
-
Novel topology of compact coplanar waveguide resonant cell low-pass filter
PublikacjaIn this study, a novel pseudoelliptic function low-pass filter (LPF) constituted by a compact coplanar waveguide resonant cell has been designed and manufactured. The lumped-element seven-pole prototype has been adequately realized by using complementary perturbations located both in signal line and ground plane metallization. The fabricated uniplanar LPF offers a compact size of 5.6 x 9.8 mm2, return loss better than 26 dB over...
-
Elastic wave propapagation in diagnostics of self-drilling system of grouted anchors
PublikacjaThe paper presents an experimental investigation of elastic wave propagation in a self-drilling hollow bar system, which is commonly used in geotechnical industry as the element of grouted ground anchors and soil nails. The single self-drilling hollow bar and self-drilling system of two bars connected by a coupler were considered. Longitudinal waves were excited at one end of the bar and registered at both ends, by means of PZT...
-
Studies on Aminoanthraquinone-Modified Glassy Carbon Electrode: Synthesis and Electrochemical Performance toward Oxygen Reduction
PublikacjaIn this paper, 9,10-anthraquinone (AQ) derivative-modified glassy carbon (GC) electrodes were studied towards the electrochemical reduction of oxygen in aqueous and non-aqueous solutions. The reaction of 1-chloro-9,10-anthraquinone with aliphatic diamines was applied for the synthesis of amino-9,10-anthraquinone derivatives. The obtained AQ derivatives were grafted onto the surface of glassy carbon electrodes by electropolymerisation...
-
Chemical Vapor Transport Route toward Black Phosphorus Nanobelts and Nanoribbons
PublikacjaChemical vapor transport (CVT) method is widely used for bulk black phosphorus (BP) fabrication. In this work, we demonstrate that CVT provides a route for the fabrication of BP nanoribbons and nanobelts. This method consists of a two-step procedure, including initial BP column growth using the CVT technique, followed by ultrasonic treatment and centrifugation. The obtained nanostructures preserve BP column dimensions, forming...
-
On the Usefulness of the Generalised Additive Model for Mean Path Loss Estimation in Body Area Networks
PublikacjaIn this article, the usefulness of the Generalised Additive Model for mean path loss estimation in Body Area Networks is investigated. The research concerns a narrow-band indoor off-body network operating at 2.45 GHz, being based on measurements performed with four different users. The mean path loss is modelled as a sum of four components that depend on path length, antenna orientation angle, absolute difference between transmitting...
-
Real-Time Basic Principles Nuclear Reactor Simulator Based on Client-Server Network Architecture with WebBrowser as User Interface
PublikacjaThe real-time simulator of nuclear reactor basic processes (neutron kinetics, heat generation and its exchange, poisoning and burn- ing up fuel) build in a network environment is presented in this paper. The client-server architecture was introduced, where the server is a pow- erful computing unit and the web browser application is a client for user interface purposes. The challenge was to develop an application running under the...
-
Hybrid Processing by Turning and Burnishing of Machine Components
PublikacjaThe paper presents a method of hybrid manufacturing process of long 5 shafts and deep holes by simultaneous turning and burnishing method. The tech- 6 nological results of the research focus on the influence of the basic technological 7 parameters of this process on the surface roughness of piston rods of hydraulic 8 cylinders. Research results are presented in the graphs as well as mathematical 9 formula. Set of samples were made...
-
PCR-RFLP assays for species-specific identification of fungi belonging to Scopulariopsis and related genera
PublikacjaFungi of the Scopulariopsis genus, commonly found in the environment, are opportunistic pathogens that can cause various types of human infections. So far, no efficient molecular method has been developed for species differentiation among Scopulariopsis and related genera. In order to advance this field, we have evaluated performance of polymerase chain reaction restriction fragment length polymorphism (PCR-RFLP) assays, based...
-
Projektowanie układów geometrycznych toru z zastosowaniem optymalizacji wielokryterialnej
PublikacjaW pracy przedstawiono metodę projektowania odcinków trasy kolejowej położonych w łuku, dostosowaną do techniki mobilnych pomiarów satelitarnych. Rozwiązanie problemu projektowego wykorzystuje zapis matematyczny i polega na wyznaczeniu uniwersalnych równań opisujących całość układu geometrycznego. Odbywa się to sekwencyjnie, obejmując kolejne fragmenty tegoż układu. Procedura projektowania ma charakter uniwersalny, gdyż w ogólnym...
-
Characterization of single-stranded DNA-binding proteins from the psychrophilic bacteria Desulfotalea psychrophila, Flavobacterium psychrophilum, Psychrobacter arcticus, Psychrobacter cryohalolentis, Psychromonas ingrahamii, Psychroflexus torquis, and Photobacterium profundum
PublikacjaBackground: Single-stranded DNA-binding proteins (SSBs) play essential roles in DNA replication, recombination and repair in Bacteria, Archaea and Eukarya. In recent years, there has been an increasing interest in SSBs, since they find numerous applications in diverse molecular biology and analytical methods. Results: We report the characterization of single-stranded DNA-binding proteins from the psychrophilic bacteria Desulfotalea...
-
Influence of bush wear in water lubricated marine stern tube bearings with shaft misalignment
PublikacjaWater lubricated propeller shaft bearings are frequently employed on modern ships due to their advantages such as durability, simplicity and low price. Specific working conditions on ships cause shaft misalignment which often results in rapid wearing of bush and shaft. Shaft misalignment could be an effect of manufacturing or assembly faults but sometimes it appears due to hull or shaft deformation. The wearing process has influence...
-
Phytoextraction and recovery of rare earth elements using willow (Salix spp.)
PublikacjaSoil and water contaminations are caused by rare earth elements (REEs) due to mining and industrial activities, that threaten the ecosystem and human health. Therefore, phytoremediation methods need to be developed to overcome this problem. To date, little research has been conducted concerning the phytoremediation potential of Salix for REEs. In this study, two Salix species (Salix myrsinifolia and Salix schwerinii) and two Salix...
-
Experimental and theoretical investigation of the reactivity of [(BDI*)Ti(Cl){η2-P(SiMe3)-PiPr2}] towards selected ketones
PublikacjaIn this work, we report a new type of reactivity of [(BDI*)Ti(Cl){η2-P(SiMe3)-PiPr2}] (1) towards ketones (BDI* = 2,6-diisopropylphenyl-β-methyldiketiminate ligand). In the reaction of 1 with acetone, cyclopentanone or cyclohexanone, a ketone moiety is inserted into Ti–Pphosphanyl or Ti–Pphosphido bonds to form complexes with a new C–P–P moiety, providing [(BDI*)Ti(Cl){η2-P(SiMe3)-PiPr2-C(Me)2O}] (2a), [(BDI*)Ti(Cl){η2-OC(Me)2P(SiMe3)-PiPr2}]...
-
Preliminary safety assessment of Polish interchanges
PublikacjaInterchanges are a key and the most complex element of a road infrastructure. The safety and functionality of interchanges determine the traffic conditions and safety of the entire road network. This applies particularly to motorways and express-ways, for which they are the only way to access and exchange traffic. A big problem in Poland is the lack of comprehensive tools for designers at individual stages of the design process....
-
Ultrasonic wave propagation and digital image correlation measurements of steel bars under 3-point bending
Dane BadawczeThe DataSet contains the results of the mechanical behaviour of a bar under a 3-point bending test. The bar was made of steel and had a cross-section of 5.96 × 5.96 mm2 and a length of 200 mm. The three-point bending test was performed using a Zwick/Roell Z10 universal testing machine (UTM), with a distance between supports of 12 cm. The parameters...
-
Photocatalytic activity of nitrogen doped TiO2 nanotubes prepared by anodic oxidation: The effect of applied voltage, anodization time and amount of nitrogen dopant
PublikacjaNitrogen doped TiO2 nanotube arrays were prepared by anodizing Ti foils in an organic electrolyte containing specified amounts of urea as nitrogen precursor. The photocatalytic activity of the samples was evaluated by analyzing the degradation kinetics of phenol in water. The influence of tubes’ length, tubes’ surface morphology and amount of nitrogen in the TiO2 lattice on hydroxyl radical formation efficiency, photocatalytic...
-
Fiber optic displacement sensor with signal analysis in spectral domain
PublikacjaIn this paper, a study of a low-coherence fiber optic displacement sensor is presented. The sensor consisted of a broadband source whose central wavelength was either at 1310 nm or 1550 nm, a sensing Fabry-Pérot interferometer operating in reflective mode and an optical spectrum analyzer acting as the detection setup. All these components were connected by a single-mode fiber coupler. Metrological parameters of the sensor were...
-
The analytical design method of railway route’s main directions intersection area
PublikacjaThe paper presents a design method related to railway track sections situated in a bend. In the method advantage is taken of an analytical form of description by using appropriate mathematical formulae. This may becomeparticularly usefulwhen the investigations are based on the data obtained from mobile satellite measurements. In the paper attention is concentrated on an universal approach creating an opportunity to diversify the...
-
Apparent Molar Volumes and Expansivities of Ionic Liquids Based on N-Alkyl-N-methylmorpholinium Cations in Acetonitrile
PublikacjaDensities of some acetonitrile solutions of ionic liquids based on N-alkyl-N-methyl-morpholinium cations, N-ethyl-N-methylmorpholinium bis(trifluoromethanesulfonyl)imide, N-butyl-N-methylmorpholinium bis(trifluoromethanesulfonyl)imide, N-methyl-N-octylmorpholinium bis(trifluoromethanesulfonyl)imide and N-decyl-N-methylmorpholinium bis(trifluoromethanesulfonyl)imide were measured at T = (298.15− 318.15) K and at atmospheric pressure....
-
Analysis of balancing of four stroke V6 engines
PublikacjaAnalysis of balance of V6 engines with a common-pin crankshaft depending on a cylinder bank angle and the crank radius to connecting rod length ratios , based on the relations derived, is presented in the paper. The bank angles providing the lowest moment of inertia forces in reciprocating motion, for selected values, were determined. The position of the plane of the main counterweights in order to maximum balance of the moment...
-
Studies on Aminoanthraquinone-Modified Glassy Carbon Electrode: Synthesis and Electrochemical Performance toward Oxygen Reduction
PublikacjaIn this paper, 9,10-anthraquinone (AQ) derivative-modified glassy carbon (GC) electrodes werestudied towards the electrochemical reduction of oxygen in aqueous and non-aqueous solutions. The reaction of 1-chloro-9,10-anthraquinone with aliphatic diamines was applied for the synthesis of amino-9,10-anthraquinone derivatives. The obtained AQ derivatives were grafted onto the surface of glassy carbon electrodes by electropolymerisation...
-
Formation and Growth of the Crack in Bonded Joints Under Mode I Fracture: Substrate Deflection at Crack Vicinity
PublikacjaAdhesive bonding is now commonly used in aircraft, cars, boats, etc. In these applications, thin panels are often bonded. In such thin structures, heterogeneous mechanical loading along the bondline edge (or potential crack front), is likely to arise due to 3D structural effects. The crack front and its vicinity is a special region, in that it is where structural properties of the adherend material meet those of the adhesive (discontinuity)....
-
Zespół wypalenia zawodowego i zmęczenie w kontekście pracy zmianowej i stresu zawodowego wśród pielęgniarek chirurgicznych
PublikacjaTwo aspects of work-related consequences among surgery nurses are discussed: burnout syndrome and fatigue, having an impact on the quality of medical care and safety of patients. Siegrist's effort-reward imbalance model has been adopted as a concept of occupational stress. The organization of working time, i.e. the length of shifts and their rotation, was considered. Nurses on twelve-hour shifts worked much harder, were more tired...
-
High Temperature Drying Process of Beech Wood (Fagus sylvatica L.) with Different Zones of Sapwood and Red False Heartwood
PublikacjaThis study examined the changes in the properties of beech wood (Fagus sylvatica L.) after intense drying. Beech wood with false red heartwood was selected as the test specimen. The test samples had dimensions of 50 mm thickness, 180 mm width, and 350 mm length. The specimens were divided into two groups, false red heartwood and sapwood. These specimens were selected with different angles of the growth rings (radial and tangential)....
-
Classification of Sea Going Vessels Properties Using SAR Satellite Images
PublikacjaThe aim of the project was to analyze the possibility of using machine learning and computer vision to identify (indicate the location) of all sea-going vessels located in the selected area of the open sea and to classify the main attributes of the vessel. The key elements of the project were to download data from the Sentinel-1 satellite [1], download data on the sea vessels [2], then automatically tag data and develop a detection...
-
What is in a name: Defining “high entropy” oxides
PublikacjaABSTRACT High entropy oxides are emerging as an exciting new avenue to design highly tailored functional behaviors that have no traditional counterparts. Study and application of these materials are bringing together scientists and engineers from physics, chemistry, and materials science. The diversity of each of these disciplines comes with perspectives and jargon that may be confusing to those outside of the individual fields,...
-
Shape Memory Materials from Rubbers
PublikacjaSmart materials are much discussed in the current research scenario. The shape memory effect is one of the most fascinating occurrences in smart materials, both in terms of the phenomenon and its applications. Many metal alloys and polymers exhibit the shape memory effect (SME). Shape memory properties of elastomers, such as rubbers, polyurethanes, and other elastomers, are discussed in depth in this paper. The theory, factors...
-
Detection of petroleum products using optical coherence tomography
PublikacjaIn this work, we present a novel method developed for the analysis of the properties of thin layers for detecting petroleum products on a water surface using a commercially available optical coherence tomography (OCT) system. The spectral density analysis of the signal from a spectroscopic OCT (S-OCT) enables us to perform the precision calculation of the thin layer thickness and other properties like homogeneity, and dispersion,...