Filters
total: 2515
filtered: 1593
displaying 1000 best results Help
Search results for: PREFABRICATED WALL COMPONENTS
-
Wideband Modeling of DC-DC Buck Converter with GaN Transistors
PublicationThe general wideband modeling method of the power converter is presented on the example of DC-DC buck converter with GaN High Electron Mobility Transistors (HEMT). The models of all basic and parasitic components are briefly described. The two methods of Printed Circuit Board (PCB) layout parameter extraction are presented. The results of simulation in Saber@Sketch simulation software and measurements are compared. Next, the model...
-
Situational Awareness Network for the Electric Power System: the Architecture and Testing Metrics
PublicationThe contemporary electric power system is highly dependent on Information and Communication Technologies which results in its exposure to new types of threats, such as Advanced Persistent Threats (APT) or Distributed-Denial-of-Service (DDoS) attacks. The most exposed components are Industrial Control Systems in substations and Distributed Control Systems in power plants. Therefore, it is necessary to ensure the cyber security of...
-
Analyzing the Geometry of the Turnouts and Their Adjustment Basing on the Tacheometer Measurements
PublicationThe article presents the results of tacheometric measurements of a station throat, as well as the method of data preparation and analysis. The calculations covered the verification of the geometry and the location of railway turnouts and crossings. The analyses were performed for the selected parameters of the turnout geometry, including their lengths and track gauge in main sections. In addition, the data were analyzed to confirm...
-
The effect of high pressure and sub-zero temperature on total antioxidant capacity and the content of vitamin C, fatty acids and secondary products of lipid oxidation in human milk
PublicationThe objective of this study was to compare of the effects of high pressure of 193 MPa at - 20°C and Low Temperature Long Time pasteurization (LTLT or holder pasteurization, 62,5°C; 30 min) on the content and composition of fatty acids (FAs), concentrations of secondary products of lipid oxidation (TBARS), the total antioxidant capacity (TAC), total vitamin C and ascorbic acid (AsA) content in human milk. It was shown that no significant...
-
APPLICATION OF CHEMOMETRIC ANALYSIS TO THE STUDY OF SNOW AT THE SUDETY MOUNTAINS, POLAND
PublicationSnow samples were collected during winter 2011/2012 in three posts in the Western Sudety Mountains (Poland) in 3 consecutive phases of snow cover development, i.e. stabilisation (Feb 1st), growth (Mar 15th) and its ablation (Mar 27th). To maintain a fixed number of samples, each snow profile has been divided into six layers, but hydrochemical indications were made for each 10 cm section of core. The complete data set was subjected...
-
Computationally Efficient Design Optimization of Compact Microwave and Antenna Structures
PublicationMiniaturization is one of the important concerns of contemporary wireless communication systems, especially regarding their passive microwave components, such as filters, couplers, power dividers, etc., as well as antennas. It is also very challenging, because adequate performance evaluation of such components requires full-wave electromagnetic (EM) simulation, which is computationally expensive. Although high-fidelity EM analysis...
-
Randomness Amplification under Minimal Fundamental Assumptions on the Devices
PublicationRecently, the physically realistic protocol amplifying the randomness of Santha-Vazirani sources producing cryptographically secure random bits was proposed; however, for reasons of practical relevance, the crucial question remained open regarding whether this can be accomplished under the minimal conditions necessary for the task. Namely, is it possible to achieve randomness amplification using only two no-signaling components...
-
Impact of high-pressure processing on the bioactive compounds of milk - A comprehensive review
PublicationHigh-pressure processing (HPP) is a promising alternative to thermal pasteurization. Recent studies highlighted the effectivity of HPP (400–600 MPa and exposure times of 1–5 min) in reducing pathogenic microflora for up to 5 logs. Analysis of modern scientific sources has shown that pressure affects the main components of milk including fat globules, lactose, casein micelles. The behavior of whey proteins under HPP is very important...
-
A Low-Cost System for Far-Field Non-Anechoic Measurements of Antenna Performance Figures
PublicationPrototype measurements are the key step in the development of antenna structures. Typically, their far-field characteristics are validated in expensive, dedicated facilities such as open range sites, or anechoic chambers. Despite being necessary for obtaining high-precision data (e.g., for device qualification), the use of costly infrastructure might not be fully justified when the main goal of measurements includes demonstration...
-
Influence of the low ambient temperature on the start-up process of hydraulic pumps
PublicationStarting hydraulic pumps in low ambient temperatures may cause: decreased hydraulic-mechanical efficiency, larger vibration of hydraulic installation, faster wear and more frequent damage to the elements of pumps, change of material properties of elements, increase of pressure drop. As a result of pressure drop in the suction pipe, large underpressure may be experienced, causing incomplete filling of pump working chambers with...
-
An analytical four-layer horizontal electric current dipole model for analysing underwater electric potential in shallow seawater
PublicationThe paper presents a new analytical four‑layer (air–water–bottom–non‑conductive layer) horizontal electric dipole model which allows an accurate approximation of ship’s Underwater Electric Potential (UEP) from a sufficient depth in shallow coastal marine waters. The numerical methods, usually Finite Element Method (FEM) or Boundary Elements Method (BEM), are typically used to estimate the electric field and the distribution of...
-
Tolerance-Aware Optimization of Microwave Circuits by Means of Principal Directions and Domain-Restricted Metamodels
PublicationPractical microwave design is most often carried out in the nominal sense. Yet, in some cases, performance degradation due to uncertainties may lead to the system failing to meet the prescribed specifications. Reliable uncertainty quantification (UQ) is therefore important yet intricate from numerical standpoint, especially when the circuit at hand is to be evaluated using electromagnetic (EM) simulation tools. Tolerance-aware...
-
Constrained multi-objective optimization of compact microwave circuits by design triangulation and pareto front interpolation
PublicationDevelopment of microwave components is an inherently multi-objective task. This is especially pertinent to the design closure stage, i.e., final adjustment of geometry and/or material parameters carried out to improve the electrical performance of the system. The design goals are often conflicting so that the improvement of one normally leads to a degradation of others. Compact microwave passives constitute a representative case:...
-
New Carvone-Based Deep Eutectic Solvents for Siloxanes Capture from Biogas
PublicationDuring biogas combustion, siloxanes form deposits of SiO2 on engine components, thus shortening the lifespan of the installation. Therefore, the development of new methods for the purification of biogas is receiving increasing attention. One of the most effective methods is physical absorption with the use of appropriate solvents. According to the principles of green engineering, solvents should be biodegradable, non-toxic, and...
-
Reduced-Cost Design Optimization of High-Frequency Structures Using Adaptive Jacobian Updates
PublicationElectromagnetic (EM) analysis is the primary tool utilized in the design of high-frequency structures. In vast majority of cases, simpler models (e.g., equivalent networks or analytical ones) are either not available or lack accuracy: they can only be used to yield initial designs that need to be further tuned. Consequently, EM-driven adjustment of geometry and/or material parameters of microwave and antenna components is a necessary...
-
On Computationally-Efficient Reference Design Acquisition for Reduced-Cost Constrained Modeling and Re-Design of Compact Microwave Passives
PublicationFull-wave electromagnetic (EM) analysis has been playing a major role in the design of microwave components for the last few decades. In particular, EM tools allow for accurate evaluation of electrical performance of miniaturized structures where strong cross-coupling effects cannot be adequately quantified using equivalent network models. However, EM-based design procedures (parametric optimization, statistical analysis) generate...
-
NUMERYCZNY MODEL OBLICZENIOWY OBIEGU TURBINY KLASY 300 MW
PublicationNiniejszy artykuł stanowi opis modelu obiegu cieplnego turbiny o mocy 360MW, utworzonego w preprocesorze numerycznego programu obliczeniowego onazwie DIAGAR. Zadaniem opisywanego modelu jest odtwarzanie zjawisk fizycznych zachodzących w poszczególnych urządzeniach składowych obiegu, zarówno podczas poprawnej (sprawnej) pracy bloku energetycznego, jak i w przypadku pojawienia się niesprawności. Utworzony...
-
Zdolności dynamiczne do budowania chmury wartości w modelach biznesów
PublicationObserwacja współczesnych metod tworzenia wartości daje podstawy do wyłonienia nowej logiki ich generowania. Analiza modeli wytwarzania wartości przez przedsiębiorstwa np. sieciowe wykazała, że formułują one chmury wartości. Struktury tych chmur są różnorodne, niejednolite, kłębiaste. Przeprowadzone prace pozwoliły na sformułowanie obrazów wartości generowanych przez twarde komponenty modeli biznesów. Osiągnięcie tych wyników pozwoliło...
-
High-Precision FIR-Model-Based Dynamic Weighing System
PublicationConveyor belt-type checkweighers are increasingly popular components of modern production lines. They are used to assess the weight of the produced items in motion, i.e., without stopping them on the weighing platform. The main challenge one faces when designing a dynamic weighing system is providing high measurement accuracy, especially at high conveyor belt speeds. The approach proposed in this paper can be characterized as a...
-
Evaluation of Open Source SIEM for Situation Awareness Platform in the Smart Grid Environment
PublicationThe smart grid as a large-scale system of systems has an exceptionally large surface exposed to cyber-attacks, including highly evolved and sophisticated threats such as Advanced Persistent Threats (APT) or Botnets. When addressing this situation the usual cyber security technologies are prerequisite, but not sufficient. The smart grid requires developing and deploying an extensive ICT infrastructure that supports significantly...
-
Effect of adopted rules of inference and methods of defuzzification on the final result of the evaluation of reliability made using the fuzzy logic methods
PublicationThe object of interest is to solve the problem of risk management of marine systems. But the main trouble is a lack of numerous and sure data on the reliability of the components of such systems. The methods based on the fuzzy logic seem to be helpful here. The goal of the article is to check the effect of using different fuzzy inference rules and methods of defuzzification on the final result of reliability assessment. The three...
-
Energy Security of Polish Consumers in 2004-2021
PublicationTheoretical background: Energy security is one of the most important components of economic security. It is influenced not only by access to energy sources and the economic situation of the state and the individual consumer. The authors adopted the definition of energy security of an individual consumer as included in the UN report. It states that energy security of an individual consumer is guaranteed when the average consumer...
-
Spectral Methods for Modelling of Wave Propagation in Structures in Terms of Damage Detection—A Review
PublicationModern methods of detection and identification of structural damage direct the activities of scientific groups towards the improvement of diagnostic methods using for example the phenomenon of mechanical wave propagation. Damage detection methods that use mechanical wave propagation in structural components are extremely effective. Many different numerical approaches are used to model this phenomenon, but, due to their universal...
-
Methods of estimating the cost of traffic safety equipment’s life cycle
Publicationn the article, the authors discuss the preliminary information necessary to determine the scope and direction of further research conducted within the project called “The influence of time and operating conditions on the durability and functionality of road safety elements”. The main objective of the project is to develop the concept of a method for optimizing the life cycle costs of road safety devices. The authors draw attention...
-
The impact of environmentally friendly refrigerants on heat pump efficiency
PublicationThis paper discusses the issue of heat pump simulation. Lower operating costs can be achieved through good equipment design and appropriate operation. Detailed technical and economic analysis inform the selection of system components with the highest possible efficiency and lower energy demand. The use of systems based on environmentally friendly refrigerants can deliver long product life, which is associated with a shorter payback...
-
Resonant DC link inverters for AC motor drive systems – critical evaluation
PublicationIn this survey paper, resonant and quasiresonant DC link inverters are reexamined for AC motor drive applications. Critical evaluation of representative topologies is based on simulation and waveform analysis to characterize current/voltage stress of components, control timing constraints and feasibility. A special concern over inverter common-mode voltage and voltage gradient du/dt limitation capacity is discussed for motor bearing...
-
The dimensions of national competitiveness: the empirical analysis based on The World Economic Forum’s data
PublicationThe aim of this research is to determine the minimum number of uncorrelated dimensions which can describe national competitiveness (NC). NC is thought of as the ability of a nation to provide a conducive environment for its firms to prosper. It is shown that the environment affects national productivity catalytically through the interactions with the production factors while itself remaining unchanged. Selected World Economic...
-
New Alternative Passive Networks to Improve the Range Output Voltage Regulation of the PWM Inverters
PublicationThis paper presents different topologies of buck-boost converters with passive input networks that have alternative topologies; this is known in the literature as a Z-source inverter. Alternative passive networks were named by the authors as T-inverters; these improve output voltage regulation of the PWM inverters. T-inverter has fewer reactive components in comparison to conventional Z-source inverter. The most significant advantage...
-
Deterioration and Protection of Concrete Elements Embedded in Contaminated Soil: A Review
PublicationCoating materials are considered one of the most antique materials of human civilization; they have been used for decoration and the protection of surfaces for millennia. Concrete structures—due to their permanent exposure to different types of environments and contaminants—require the use of coatings that contribute to its preservation by reducing the corrosion of its components (steel and aggregates). This article intends to...
-
Pool boiling of nanofluids on rough and porous coated tubes: experimental and correlation
PublicationThe paper deals with pool boiling of water-Al2O3 and water- Cu nanofluids on rough and porous coated horizontal tubes. Commercially available stainless steel tubes having 10 mm outside diameter and 0.6 mm wall thickness were used to fabricate the test heater. The tube surface was roughed with emery paper 360 or polished with abrasive compound. Aluminium porous coatings of 0.15 mm thick with porosity of about 40% were produced by...
-
Toward Mechanosynthesis of Diamondoid Structures: X. Commercial Capped CNT SPM Tip as Nowadays Available C2 Dimer Placement Tool for Tip-Based Nanofabrication
PublicationAccording to Drexler, advanced mechanosynthesis will employ advanced nano-machines, but advanced nano-machines will themselves be products of advanced mechanosynthesis. This circular relationship must be broken via TBN technology development. In this article, the possibility of using easily available commercial CNT tips to assemble carbon-based intermediate generations of nano-devices is considered. Mechanosynthesis of a target...
-
Effect of irradiation intensity and initial pollutant concentration on gas phase photocatalytic activity of TiO2 nanotube arrays
PublicationWell-organized TiO2 nanotube arrays were fabricated via one-step anodization process. The as-prepared TiO2 nanotubes were characterized by X-ray powder diffractometry (XRD), X-ray photoelectron spectroscopy (XPS), diffuse reflectance spectroscopy (DRS) and scanning electron microscopy (SEM). Photocatalytic activity of obtained photocatalyst was studied in reaction of toluene degradation in the gas phase using low powered and low...
-
An investigation of microstructural basis for corrosion behavior of Al-CNT composites fabricated by SPS
PublicationIn this research effect of the addition of multi-wall carbon nanotubes (MWCNTs) as additive powder on microstructure and corrosion behavior of fabricated Al-CNT composites was studied. The aluminum powder and CNTs were mixed with high energy planetary ball-mill. It is observed that by increasing milling time, the uniformity of CNTs on aluminum matrix and consequently corrosion resistance of Al-CNT composite is increased. On the...
-
Optimization of the distance between the vertical plates in the convective air heat exchanger
PublicationThis paper examines the influence of the distance between vertical plates on the intensity of free convective heat transfer along with the optimization of this distance. Experimental tests were carried out for one model channel of such an heat exchanger with widths , 0.085 and 0.18 m. This channel, open at the top and sides, was formed by two isothermal symmetrically heated parallel vertical plates of dimensions m and m. The influence...
-
Multi-objective optimization of the cavitation generation unit structure of an advanced rotational hydrodynamic cavitation reactor
PublicationHydrodynamic cavitation (HC) has been widely considered a promising technique for industrial-scale process intensifications. The effectiveness of HC is determined by the performance of hydrodynamic cavitation reactors (HCRs). The advanced rotational HCRs (ARHCRs) proposed recently have shown superior performance in various applications, while the research on the structural optimization is still absent. The present study, for the...
-
Nonlinear material identification of heterogeneous isogeometric Kirchhoff–Love shells
PublicationThis work presents a Finite Element Model Updating inverse methodology for reconstructing heterogeneous materialdistributions based on an efficient isogeometric shell formulation. It uses nonlinear hyperelastic material models suitable fordescribing incompressible material behavior as well as initially curved shells. The material distribution is discretized by bilinearelements such that the nodal values...
-
TiO 2 Co x O y composite nanotube arrays via one step electrochemical anodization for visible light–induced photocatalytic reaction
PublicationTiO2CoxOy (x = 1, y = 1 or x = 3, y = 4) composite photocatalysts have been synthesized via one step anodic anodization of TiCo alloys. The effects of the cobalt content in the alloy (5, 10 and 15 wt%), water content (2, 5 and 10%) in the electrolyte solution, and applied voltage (30, 40 and 50 V) during the anodization process on the morphology and surface properties. Additionally, the dependence of cobalt content in the nanotubes...
-
Cross-talk Between the Heart and Arteries in Older 65+ Adults
PublicationRegulatory synchronization between the heart and the arterial walls is essential for optimal blood delivery to tissues. We investigated functional coherence between heart rhythm and aortic wall compliance in 30 volunteers aged 65 – 74. ECG and carotid and iliac pulse-wave were recorded and digitized at 2 kHz. Carotid-femoral pulse-wave transit time (cfTT) which reflex aortic compliance was assessed using the intersecting tangent...
-
Thermal and economic investigation of straight and U-bend double tube heat exchanger with coiled wire turbulator
PublicationExperimental research has been carried out for four individual heat exchanger constructions, i.e., plain double tube, turbulized double tube, plain U-bend and U-bend with turbulator. Tests were made for the water-water system. The study covered a wide measuring range, i.e., Re = 800–9000 – on the shell side, for a constant cold water temperature of 9 ◦C and hot water of 50 ◦C. The heat exchangers were made from copper tubes with...
-
Visual Dimensions of Modeling Languages in Interdisciplinary Perspective
PublicationUżyteczność języków modelowania wizualnego zależy od notacji. Notacja może być postrzegana jako zestaw wizualnych komponentów, które w określony sposób oddziałują na ludzkie oko i ludzki mózg. Referat przedstawia analizę interdyscyplinarną wykonaną w celu lepszego zrozumienia wizualnych wymiarów języków modelowania. Wizualne wymiary pochodzą z teorii opisujących percepcję wzrokową, wizualizację danych oraz reprezentacje poznawcze....
-
Pomiar naprężeń własnych metodą Barkhausena za pomocą sondy z wirującym polem magnetycznym
PublicationW pracy przedstawiono nowy sposób pomiaru naprężeń własnych w elementach konstrukcji z wykorzystaniem polowego efektu Barkhausena. Informację o stanie naprężeń uzyskano z analizy rozkładu kątowego natężenia efektu Barkhausena zmierzonego w sposób automatyczny poprzez sondę z wirującym polem magnetycznym. Przedstawiono zasadę działania i opis układu pomiarowego oraz przykłady wykorzystania tej metody w ocenie stanu naprężenia w...
-
Performance Analysis of the "Intelligent" Kirchhoff- Law - Johnson-Noise Secure Key Exchange
PublicationThe Kirchhoff-law - Johnson-noise (KLJN) secure key distribution system provides a way of exchanging theoretically secure keys by measuring random voltage and current through the wire connecting two different resistors at Alice’s and Bob’s ends. Recently new advanced protocols for the KLJN method have been proposed with enhanced performance. In this paper, we analyze the KLJN system and compare with the „intelligent” KLJN (iKLJN)...
-
Electrochemical investigations on the corrosion behaviour of reinforcing steel in diatomite- and zeolite-containing concrete exposed to sulphuric acid
PublicationCorrosion is a major concern for most structural applications. Its detrimental effect significantly reduces the life of metallic components. This paper presents the results of an experimental investigation of corrosion in the steel reinforcement of concrete samples having three different substituents: 20% diatomite, 20% zeolite, and a reference without zeolite or diatomite. All concrete specimens were subjected to a solution of...
-
Risk criteria for sea-going ships arising from the operation of the main engines' crankshaft - conecting rod - piston systems
PublicationIn the article the risk criterion for sea-going ships arising from the operation of the main engines' crankshaft - connecting rod - piston systems is proposed. These criterion is based on the procedures recommended in the Formal Safety Assessment method developed under the auspices of International Maritime Organization (IMO). First of all the collective risk criterion for ship has been proposed. In the next step, the share of...
-
Modern Platform for Parallel Algorithms Testing: Java on Intel Xeon Phi
PublicationParallel algorithms are popular method of increasing system performance. Apart from showing their properties using asymptotic analysis, proof-of-concept implementation and practical experiments are often required. In order to speed up the development and provide simple and easily accessible testing environment that enables execution of reliable experiments, the paper proposes a platform with multi-core computational accelerator:...
-
Foundations of Grid Processing Architecture for the Comcute System
PublicationFundamental system algorithms and structures implemented in the Comcute system are described and analysed in detail. Layered architecture of the system model is highlighted. System tasks of the layers are elaborated, presented and described. Operational details of communication interfaces among layers are worked out and examined. The focus is put onto implemented system components with regard to their operability and efficiency....
-
Non-Nutritive Bioactive Compounds in Food of Plant Origin
PublicationThe increasing knowledge on the health benefits of certain food ingredients, in particular, those of plant origin, opened the discussion of the possibility of using edible plants or their active components in the prevention of non-communicable diseases. The health-promoting properties of plant foods are related to the presence of non-nutritive compounds, mainly plant secondary metabolites, which can affect many biological mechanisms...
-
An Innovative Floating System with a Savonius Rotor as a Horizontal-Axis Wind Turbine
PublicationIn this project, an innovative wind turbine was designed for a floating plant. A large Savonius rotor was replaced with a double-rotor wind turbine implemented as a horizontal-axis turbine. This double rotor was positioned on the tip of a thrust plate and fixed to the deck of a catamaran. Simple 2D numerical simulations were performed to confirm the effectiveness of the concept. An analysis of the floating system configuration...
-
THE COMPOSITION MODULATION EFFECT IN GaInPAs SOLID SOLUTIONS AS A MANIFESTATION OF ENERGY RESONANCE AFTER MATERIAL'S SPINODAL DECOMPOSITION
PublicationThe Cahn-Hilliard model concepts are extended to describe the spinodal decomposition of Ga$_x$In$_{1-x}$P$_y$As$_{1-y}$ solid solutions grown on the InP substrate. The energy of elastic deformation of the thin layer of a solid solution was calculated on the assumption of its coherent conjugation with the massive InP substrate. The excess energy of component mixing in the solid phase was modeled in accordance with the simple solution...
-
A Note on Fractional Curl Operator
PublicationIn this letter, we demonstrate that the fractional curl operator, widely used in electromagnetics since 1998, is essentially a rotation operation of components of the complex Riemann–Silberstein vector representing the electromagnetic field. It occurs that after the wave decomposition into circular polarisations, the standard duality rotation with the angle depending on the fractional order is applied to the left-handed basis vector...