Filters
total: 2345
filtered: 2009
-
Catalog
Chosen catalog filters
displaying 1000 best results Help
Search results for: THERMAL CRACKING PROBABILITY
-
Advanced Bayesian study on inland navigational risk of remotely controlled autonomous ship
PublicationThe arise of autonomous ships has necessitated the development of new risk assessment techniques and methods. This study proposes a new framework for navigational risk assessment of remotely controlled Maritime Autonomous Surface Ships (MASS). This framework establishes a set of risk influencing factors affecting safety of navigation of a remotely-controlled MASS. Next, model parameters are defined based on the risk factors, and...
-
Wpływ zbrojenia polimerowymi włóknami rozproszonymi na wybrane właściwości mieszanek mineralno-asfaltowych
PublicationW artykule przedstawiono wybrane wyniki badań mieszanek mineralno-asfaltowych zbrojonych polimerowymi włóknami rozproszonymi. Ocenie poddano mieszankę włókien zbrojących aramidowo-poliolifenowych pod kątem wpływu ich zastosowania na właściwości niskotemperaturowe i odporności na deformacje trwałe mieszanek mineralno-asfaltowych. Właściwości niskotemperaturowe oceniano na podstawie testu zginania próbek belkowych oraz na podstawie...
-
The effect of macro polymer fibres length and content on the fibre reinforced concrete
PublicationThe paper presents studies of a ready-mix concrete containing polymer fibres of three different lengths: 24, 38 and 54 mm. The performed tests allowed to determine the effect of fibre volume fraction and length on the concrete strength. The basic parameters of concrete mixture (consistency, air content and bulk density) were identified. Fibre reinforced concrete belongs to a group of composite materials. The polymer fibres are...
-
THE POSSIBILITY OF USE OF LASER-MODIFIED Ti6Al4V ALLOY IN FRICTION PAIRS IN ENDOPROSTHESES
PublicationThe purpose of this paper is to show results of laser treatment at cryogenic conditions of the Ti6Al4V alloy used for orthopedic applications. That modification process ought to bring beneficial changes of microstructure and residual stresses in the surface layer. The paper presents the abrasive wear of the base and laser remelted material in association with ceramics Al2O3. Despite the surface cracking after laser treatment the...
-
On the differential effect of temperature on the Nusselt-Rayleigh relationship in free convection
PublicationThe aim of and inspiration behind this paper was to explain the reasons, also observed by other researchers, of the discrepancy in the results of experimental free convection, which for small Rayleigh and Nusselt numbers in the initial phase of research can sometimes reach several hundred percent. These discrepancies decrease with increasing heating power and plate surface temperature, in proportion to the increase in Ra and Nu,...
-
Weldability of high strength steel in underwater environment
PublicationThe article describes the problems with weldability of high-strength steels in the aquatic environment. The tendency of steel S355J2G3 and S500M to form cold cracks when welded in wet welding conditions has been experimentally evaluated. It was found that the tested steels have a high propensity to cracking. An experiment has been proposed and tested to evaluate the usefulness of the tempering bead technique as a method of improving...
-
Damage Detection Strategies in Structural Health Monitoring of Overhead Power Transmission System
PublicationOverhead power transmission lines, their supporting towers, insulators and other elements create a highly distributed system that is vulnerable to damage. Typical damage scenarios cover cracking of foundation, breakage of insulators, loosening of rivets, as well as cracking and breakage of lines. Such scenarios may result from various factors: groundings, lightning strikes, floods, earthquakes, aeolian vibrations, conductors galloping,...
-
Oxidation and hydrogen behavior in Zr-2Mn alloy
PublicationThe purpose of the present research was to determine the oxidation and hydrogenation behavior in the new Zr-2Mn alloy. The oxidation of alloy was performed at temperatures between 350°C and 900°C for 30 minutes. The hydrogen charging was made for 72 h at a current density 80 mA/cm2. The charged samples were heat treated at 400°C for 4 h to obtain a uniform hydrogen profile content across the sample. The oxidation resulted in an...
-
Damage of a post-tensioned concrete bridge – Unwanted cracks of the girders
PublicationThe cracking of a post-tensioned T-beam superstructure, which was built using the incremental launching method, is analyzed in the paper. The problem is studied in detail, as specific damage was observed in the form of longitudinal cracks, especially in the mid-height zone of the girder at the interface of two assembly sections. The paper is a case study. A detailed inspection is done and non-destructive testing results of the...
-
Effects of CO2 and Nd:YAG Laser Remelting of the Ti6Al4V Alloy on the Surface Quality and Residual Stresses
PublicationThe titanium alloys are materials susceptible to tribological wear and the laser treatment can be applied in surface treatment processes to obtain for example higher hardness level. From the other side, it is important to take into consideration, that hardness increase that can be connected with cracks . The aim of this research was to investigate the effects of different lasers and the process parameters on the form and level...
-
Exergy and Energy Analyses of Microwave Dryer for Cantaloupe Slice and Prediction of Thermodynamic Parameters Using ANN and ANFIS Algorithms
PublicationThe study targeted towards drying of cantaloupe slices with various thicknesses in a microwave dryer. The experiments were carried out at three microwave powers of 180, 360, and 540 W and three thicknesses of 2, 4, and 6 mm for cantaloupe drying, and the weight variations were determined. Artificial neural networks (ANN) and adaptive neuro-fuzzy inference systems (ANFIS) were exploited to investigate energy and exergy indices of...
-
On the Hat Problem on the Cycle C7
PublicationThe topic is the hat problem in which each of n players is randomly fitted with a blue or red hat. Then everybody can try to guess simultaneously his own hat color by looking at the hat colors of the other players. The team wins if at least one player guesses his hat color correctly, and no one guesses his hat color wrong; otherwise the team loses. The aim is to maximize the probability of a win. In this version every player can...
-
UKŁADY KONSTRUKCYJNE LEKKIEJ OBUDOWY
PublicationW artykule przedstawiono rozwiązania konstrukcyjne przegród zewnętrznych lekkiej obudowy jednowarstwowych (nieizolowanych termicznie), wielowarstwowych (izolowanych termicznie) oraz szklano-metalowych. Omówiono procesy modyfikacji konstrukcji ścian. Podano przykładowe rozwiązania.
-
Quadratic stochastic operators on Banach lattices
PublicationWe study the convergence of iterates of quadratic stochastic operators that are mean monotonic. They are defined on the convex set of probability measures concentrated on a weakly compact order interval S = [0, f] of a fixed Banach lattice F. We study their regularity and identify the limits of trajectories either as the “infimum” or “supremum” of the support of initial distributions.
-
Modelling of laminated glass PVB walls of buildings exposed to vehicle impact with different speeds
PublicationThis paper presents an analytical model, developed for laminated glass subjected to a low-velocity impact. It has the ability to capture glass cracks as well as large non-linear deformations. It is based mathematically on the firstorder deformation concept, which considers the effect of membrane and transverse shear as well as bending. This theory uses damage mechanics to capture the glass cracking. For this purpose, several experiments...
-
Usage of Memi-Markov Process in Operation Evaluation of Diesel Engine
PublicationIn paper, the proposition of quantitative evaluation of operation using semi-Markov processes theories has been presented. Basic assumptions, essential for creating mathematical model on example of diesel engine were shown. Special attention was given to practical aspects of using established mathematical model. Example of characteristic of analysed process - temporary distribution of probability was assigned.
-
Application of Game Theory to Conflict Management in a Construction Contract
PublicationInterest has recently grown in the application of game theory (GT) to solve a number of diverse problems in the field of construction. The use of GT by a general contractor (GC) of construction works to indicate the best strategy leading to winning court proceedings in a situation of conflict with investor (IN), has not been investigated until now. Thus the aim of this paper is to indicate the optimal strategy from the GC viewpoint...
-
Novel Investigation of Higher Order Spectral Technologies for Fault Diagnosis of Motor-Based Rotating Machinery
PublicationIn the last decade, research centered around the fault diagnosis of rotating machinery using non-contact techniques has been significantly on the rise. For the first time worldwide, innovative techniques for the diagnosis of rotating machinery, based on electrical motors, including generic, nonlinear, higher-order cross-correlations of spectral moduli of the third and fourth order (CCSM3 and CCSM4, respectively), have been comprehensively...
-
Effect of wet Hydrogen Sulfide on Carbon Steels Degradation in Refinery Based on Case Study
PublicationMaterial degradation caused by wet hydrogen sulfide (Wet H2S) is one of the major issues in refineries. Carbon steel is the main construction material used in refineries and is subjected not only to thickness loss but the hydrogen is the major concern. H2S leads to high atomic hydrogen penetration in steel which causes degradation in the form of blistering and/or cracking (HIC/SOHIC) and stress cracking in the area of welds and...
-
Advanced fatigue and rutting characterisation of Polish asphalt mixtures based on the VECD model and viscoplastic shift model
PublicationThe advanced asphalt mixture performance-related specifications (AM-PRS) recently developed in USA can allow an optimisation of the design process of asphalt pavements thanks to the possibility to fully take into account the intrinsic material properties. In this study, four typical Polish mixtures, i.e. a Stone Mastic Asphalt (SMA) for wearing course, two mixtures for binder course with neat bitumen or Polymer modified Bitumen...
-
Wyrażanie niepewności za pomocą przedziałów
PublicationZ perspektywy dwóch różnych interpretacji prawdopodobieństwa - klasycznej (częstościowej) i subiektywnej (bayesowskiej) oraz propozycji nowego przewodnika ustalającego zasady obliczania i wyrażania niepewności pomiaru (GUM), porównano sposoby komunikowania niepewności za pomocą przedziałów: ufności, bayesowskiego, objęcia, rozszerzenia.
-
Active Dynamic Thermography in Medical Diagnostics
PublicationThis is an overview of active thermal imaging methods in medical diagnostics using external thermal stimulation. In this chapter, several clinical cases diagnosed using the active dynamic thermography method, ADT, are presented. Features of this technology are discussed and main advantages underlined. Applications in skin burn diagnostics and quantitative evaluation leading to modern classification of burned patients for further...
-
Numerical investigations on early indicators of fracture in concrete at meso-scale.
PublicationFracture is a major reason of the global failure of concretes. The understanding of fracture is important to ensure the safety of structures and to optimize the material behaviour. In particular an early prediction possibility of fracture in concretes is of major importance. In this paper, concrete fracture under bending was numerically analysed using the Discrete Element Method (DEM). The real mesoscopic structure of a concrete...
-
Four-state stochastic model of changes in the reliability states of a motor vehicle
PublicationThe properties of semi-Markov processes have been generally characterized and the applicability of the theory of such processes to the determining of the reliability of motor cars and other road vehicles has been explained. A formal description of the process of changes in the motor vehicle technical states considered as reliability states and a model of this process in the form of a one-dimensional stochastic process have been...
-
IEEE 802.15.4a Impulse Radio Spectrum Shaping by Changes in Pulse Sequence
PublicationThis paper presents one of possible techniques of IEEE 802.15.4a ultra-wideband signal spectrum control, based on changes in sequences of transmitted pulses with very short duration time. This technique can reduce probability of mutual interferences between new ultra-wideband and existing narrowband devices, which may be helpful in further studies on allowing UWB transmission in wider range of spectrum in theEuropean Union.
-
Interference aware bluetooth scatternet (re)configuration algorithm IBLUERA
PublicationThis paper presents a new algorithm IBLUEREA, which enables reconfiguration of Bluetooth scatternet to reduce interference. IBLUEREA makes use of the complex model comparing ISM environment efficiency. The mechanism envisages the use of the assessment of the probability of successful (unsuccessful) frame transmission in order to take a decision concerning co-existence of technologies which make use of the same ISM band (here Bluetooth...
-
An improved method for flow boiling heat transfer with account of the reduced pressure effect
PublicationIn the paper are presented the results using the authors own model to predict heat transfer coefficient during flow boiling. The model has been tested against a large selection of experimental data to investigate the sensitivity of the in-house developed model. In the work are presented the results of calculations obtained using the semi-empirical model on selected experimental flow boiling data of the refrigerants: R134a, R1234yf,...
-
Application of stereology for two-phase flow structure validation in fluidized bed reactors
Publication -
Using adsorption chillers for utilising waste heat from power plants
Publication -
An adaptive neuro-fuzzy model of a re-heat two-stage adsorption chiller
Publication -
Termooksydacyjna i fotooksydacyjna degradacja pianek poliuretanowych
PublicationPrzeprowadzono ocenę efektywności działania wybranych środków przeciwstarzeniowych w sztywnych piankach poliuretanowych, otrzymywanych na drodze syntezy jednoetapowej. Ocenę tę oparto na pomia-rach zmian barwy oraz wytrzymałości mechanicznej zsyntezowanych materiałów. Na podstawie analizy uzyskanych wyników stwierdzono, iż dodatek 3% mieszaniny I rzędowego antyutleniacza fenolowego oraz benzotriazolowego absorbera UV znacząco zmniejsza...
-
Zagrożenia korozyjne stali nierdzewnych w przemyśle spozywczym
PublicationPrzedstawiono przyczyny występowania zagrożeń korozyjnych stali nierdzewnych w przemyśle spożywczym. Szczegółowo omówiono mechanizm oraz sposób zapobiegania korozji wżerowej, szczelinowej oraz pękania korozyjnego. Zaprezentowano dokumentację fotograficzną omówionych typów korozji. Wskazano podstawowe problemy związane z doborem materiałów konstrukcyjnych do budowy instalacji w przemyśle spożywczym.
-
The application of neural networks in forecasting the influence of traffic-induced vibrations on residential buildings
PublicationTraffic-induced vibrations may cause the cracking of plaster, damage to structural elements and, in extreme cases, may even lead to the structural collapse of residential buildings. The aim of this article is to analyse the effectiveness of a method of forecasting the impact of vibrations on residential buildings using the concept of artificial intelligence. The article presents several alternative forecasting systems for which...
-
Experimental study of the post tensioned prestressed concrete corbels
PublicationThe results of experimental investigation of 6 symmetrical double prestressed corbels of variable shear span to depth ratio and variable location of prestressing bars are presented in the paper. The post ten- sioned corbels were prestressed with Macalloy 1030 bars of 25 mm in diameter. The results of the tests were compared with the cracking and load carrying capacity of corbels reinforced with passive reinforce- ment. As a result...
-
Integration of thermographic data with the 3D object model
PublicationThe aim of the paper is to present new method for merging the 3D model data of the measured object with thermograms. Our technique is based on the combination of visual 3D imaging technique and thermal imaging technique, which maps the 2D thermograms on to 3D anatomical mesh model. The combination of these imaging modalities allows the generation of combined 3D and thermal data from which thermal signatures can be verified and...
-
Review and evaluation of cold recycling with bitumen emulsion and cement for rehabilitation of old pavements
PublicationThe article presents Polish experience with cold recycling of asphalt pavements with theusage of bituminous emulsion and cement. In the 1990s numerous roads in Polandrequired immediate reinforcement due to their significant degradation. Implementation ofthe cold recycling technology was one of the solutions to this problem. Cold recycledmixtures containebeside the recycled asphalt pavement and aggregateetwo differenttypes of binding...
-
Tools for Automatic Wound Healing Evaluation
PublicationFinal results of the research project devoted to development of a new objective and quantitative method of post cardiosurgery wound healing diagnostics, already preliminary discussed at the QIRT 2014 Conference, is presented. We assumed that thermal processes should be effective in subtle description of temporal changes of tissue thermal properties after surgical interventions. To prove this assumption more than 400 patients after...
-
Numerical modeling of the combustion in a lab-scale pulverized-coal fired combustion chamber
PublicationThis work presents results of numerical modeling of the combustion process inside a lab-scale drop-tube chamber, designed to investigate the slagging properties of the flue ashes, created through the solid fuel firing. Interaction between turbulence and chemistry is accounted by use of probability density function (PDF). FLUENT inputs for non-premixed combustion chemistry modeling are defined. A discrete second phase of the coal...
-
Numerical modeling of the combustion in a lab-scale pulverized-coal fired combustion chamber
PublicationThis work presents results of numerical modeling of the combustion process inside a lab-scale drop-tube chamber, designed to investigate the slagging properties of the flue ashes, created through the solid fuel firing. Interaction between turbulence and chemistry is accounted by use of probability density function (PDF). FLUENT inputs for non-premixed combustion chemistry modeling are defined. A discrete second phase of the coal...
-
Experimental Study of Dapped-End Beams Subjected to Inclined Load
PublicationThis paper presents the results of an experimental investigation of the reinforced concrete (RC) dapped-end beams loaded with inclined forces, compared to identical ones loaded with vertical forces only. Such a load may occur in, for example, Gerber's joints or in dapped-end beams supported on corbels, where the vertical gravitation force is additionally completed with horizontal forces caused by temperature differences, shrinking,...
-
Wet H2S corrosion and degradation of pipeline in amine regeneration system
PublicationThe paper presents the results of NDT examinations, metallographic tests and risk assessment of degradation related to corrosion of amine regeneration unit in a desulphurisation system. Intensive corrosion resulting from acid gases environment upon water condensation causes perforation of the pipeline. Detailed analysis reveals cracking related to the mechanism of wet H2S. Hydrogen penetration, resulting from the wet H2S process,...
-
Development of fragility curves in adjacent steel moment-resisting frames considering pounding effects through improved wavelet-based refined damage-sensitive feature
PublicationFragility curves present useful information related to earthquake-induced probability assessment of steel moment-resisting frames (MRFs) and determine the probability of the damage exceedance at different floor levels of MRFs. The review of the literature shows that most of the previous studies dealing with the fragility curves were based on conventional measures, such as spectral acceleration at the first mode period, peak...
-
Improved energy management technique in pipe-embedded wall heating/cooling system in residential buildings
PublicationEffective and environmentally responsive techniques of energy management in residential buildings are desirable for the resulting reduction of energy costs and consumption. In this paper, an improved and efficient technique of energy management in pipe-embedded wall heating/cooling systems, called the Thermal Barrier, is described. Specifically, the Thermal Barrier is a technique focused on the management and control of heat...
-
Improved energy management technique in pipe-embedded wall heating/cooling system in residential buildings
PublicationEffective and environmentally responsive techniques of energy management in residential buildings are desirable for the resulting reduction of energy costs and consumption. In this paper, an improved and efficient technique of energy management in pipe-embedded wall heating/cooling systems, called the Thermal Barrier, is described. Specifically, the Thermal Barrier is a technique focused on the management and control of heat supply...
-
AN OVERVIEW OF HEAT TRANSFER ENHANCEMENT BASED UPON NANOPARTICLES INFLUENCED BY INDUCED MAGNETIC FIELD WITH SLIP CONDITION VIA FINITE ELEMENT STRATEGY
PublicationThe mathematical model of heat generation and dissipation during thermal energy transmission employing nanoparticles in a Newtonian medium is investigated. Dimensionless boundary layer equations with correlations for titanium dioxide, copper oxide, and aluminium oxide are solved by the finite element method. Parameters are varied to analyze their impact on the flow fields. Various numerical experiments are performed consecutively...
-
The Impact of Spatiotemporal Changes in Land Development (1984–2019) on the Increase in the Runoff Coefficient in Erbil, Kurdistan Region of Iraq
PublicationNowadays, geospatial techniques are a popular approach for estimating urban flash floods by considering spatiotemporal changes in urban development. In this study, we investigated the impact of Land Use/Land Cover (LULC) changes on the hydrological response of the Erbil basin in the Kurdistan Region of Iraq (KRI). In the studied area, the LULC changes were calculated for 1984, 1994, 2004, 2014 and 2019 using the Digital Elevation...
-
Wykorzystanie sztucznych sieci neuronowych do szacowania wpływu drgań na budynki jednorodzinne
PublicationW artykule przedstawiono metodę prognozowania wpływu drgań na budynki mieszkalne z wykorzystaniem sztucznych sieci neuronowych. Drgania komunikacyjne mogą doprowadzić do uszkodzenia elementów konstrukcyjnych, a nawet do awarii budynku. Najczęstszym efektem są jednak rysy, pękanie tynku i wypraw. Metody oparte na sztucznej inteligencji są przybliżone, ale stanowią wystarczająco dokładną i ekonomiczną alternatywę dla tradycyjnych...
-
Donor-substituted SrTi1+xO3−δ anodes for SOFC
PublicationNonstoichiometric Nb-substituted SrTiO3 compounds were investigated in order to discuss the influence of nonstoichiometry at the sample properties in the light of recent results reported in the literature. Structural and electrical properties of samples were characterized. Investigated compounds were also applied as anodes for Solid Oxide Fuel Cells and their reactivity with YSZ electrolyte was examined. The defect chemistry explaining...
-
Influence of external climate on natural ventilation performance in buildings
PublicationNatural ventilation is driven by either buoyancy forces or wind pressure forces or their combinations that inherit stochastic variation into ventilation rates [ CITATION Hun99 \l 1045 ]. We now that these factors have influence on air flow speed and thermal comfort inside building. This work examines the relationship between external climate and natural ventilation including thermal comfort. The work tries in the first instance...
-
Rigid polyurethane foams modified with selected flame retardants
PublicationThe flame retardants: expandable graphite, triethylphosphatehas been used in rigid polyurethane foams (PUFs). The influence of fillers amounts on processing parameters, physical-mechanical properties (compression strength, density, water absorption, brittleness)and thermal properties (thermal stability) of such foams has been analyzed.The gel, cram and rise time for PUFs modified with flame retardant has been observed during synthesis...