Filters
total: 7193
filtered: 4744
displaying 1000 best results Help
Search results for: TOWING AND INSTALLATION OF SPAR PLATFORMS, ANCHORING OF SPAR TYPE PLATFORMS, CALCULATION OF DYNAMIC LOADS IN ANCHOR ROPES
-
Quantitative Active Dynamic Thermal IR-Imaging and Thermal Tomography in Medical Diagnostic
PublicationPrinciples of Active dynamic thermal (ADT) IR-imaging and Thermal Tomography are described in details. Basic medical applications of this new modality are also discussed.
-
Validation of dynamic electrochemical impedance spectrograms using autocorrelation function
PublicationValidation of impedance data is essential for checking the reliability of experimental data. Kramers – Kronig transformation is used to verify data obtained from classical Electrochemical Impedance Spectroscopy (EIS) measurements. Data obtained from Dynamic Electrochemical Impedance Spectroscopy (DEIS) could be validated in the same way, but in this case, there is no information about internal consistency between every single spectrum...
-
Traffic Type Influence on QoS Network Performance of Streaming Traffic Class
PublicationFeasibility study on QoS routing proved that the traffic type influence the network performance. The performance is defined here as a number of packets serviced by the network. In the paper additional element - buffers lengths used in service system was verified in terms of dependencies with routing performance. We present results obtained by simulation for many simulation scenarios. Analysis was done for two different network...
-
Tripping of F-type RCDs for sinusoidal residual current with superimposed smooth DC component
PublicationRecent trends in green energy development make that photovoltaics and electric vehicles are applied on an increasing scale. In both photovoltaic and electric vehicle charging installations, a significant value of DC component of the earth fault current may appear, which is a challenge, in particular, for commonly used residual current devices (RCDs). This paper presents results of the laboratory test on the operation of F-type...
-
Soft-mode enhanced type-I superconductivity in LiPd2Ge
PublicationThe synthesis, crystal structure, and physical properties (magnetization, resistivity, heat capacity) in combination with theoretical calculations of the electronic structure and phonon properties are reported for intermetallic compounds LiPd2X (X = Si, Ge, and Sn). LeBail refinement of powder x-ray diffraction data confirms that all compounds belong to the Heusler family (space group Fm-3m, No. 225). The lattice parameter increases...
-
Analysis of start energy of Stirling engine type alpha
PublicationThe Stirling engine type alpha is composed of two cylinders (expansion space E and compression space C), regenerator that forms the space between the cylinders and the buffer space (under the pistons). Before the start-up and as a result of long-term operation, the average pressure in the working space (above the pistons) and in the buffer space is the same. However, in the initial phase of operation, the average pressure in the...
-
The Influence of Cement Type on Early Properties of Cold In-Place Recycled Mixtures
PublicationCold in-place recycling is a commonly used maintenance treatment in rehabilitation of low and medium volume roads in Poland. Typically, two types of binding agents are used—cement and bituminous emulsion (or foamed bitumen).Due to the harsh Polish climate with many freeze/thaw cycles and frequent occurrence of saturated conditions, the used amounts of cement are higher than those commonly used in warmer parts of Europe. While there...
-
Electrochemical Evaluation of Sustainable Corrosion Inhibitors via Dynamic Electrochemical Impedance Spectroscopy
PublicationFinding suitable measurement methods for the effective management of electrochemical problems is of paramount importance, particularly for improving efficiency in corrosion protection. The need for accurate measurement techniques specific to nonstationary conditions has long been recognized, and promising approaches have emerged. This chapter introduces dynamic electrochemical impedance spectroscopy as a novel advancement in electrochemistry...
-
Experimental determination of dynamic properties of cylindrical steel tank model filled with liquid
PublicationIn technical branches, such as chemical or petroleum industries, cylindrical steel tanks are essential structures used for storage of liquid products. Any failure might have disastrous consequences, therefore their safety and reliability is essential. The aim of the present paper is to show the results of the experimental study which has been conducted on a scaled model of a real tank used in Poland. The investigation was carried...
-
Intermetallic disordered magnet Gd2Pt1.1Ge2.9 and its relation to other AlB2 -type compounds
PublicationThe intermetallic germanide Gd 2 Pt 1.1 Ge 2.9 was synthesized using an arc-melting method. The crystal structure was characterized using powder x-ray diffraction, revealing a disordered ternary AlB 2 -type structure (space group P 6 / m m m , No. 191) with lattice parameters a = 4.2092 ( 1 ) Å and c = 4.0546 ( 2 ) Å . Physical properties were investigated by magnetic susceptibility and heat capacity measurements, which...
-
Effect of starch fillers on the dynamic mechanical properties of rubber biocomposite materials
PublicationIn the paper the results of dynamic mechanical study of the biocomposites containing one of two types of (potato or corn) strach used as fillers in different amount were discussed. The composites were obtained from rubbery mixture containing natural rubber (NR) as a main component. Thermomechanical analyses (by DMA) showed that the used quantity of strach fillers only slightly influence on the glass transition temperature of vulcanizates.
-
Simulation Results of Dynamic Capacity Reallocation in Hierarchical Cell Structure of UMTS Network
PublicationIn the paper simulation results of dynamic capacity reallocation between different layers of hierarchical cell structure of UMTS network has been described. This approach for load management seems to be useful for improving the resource utilization perfmorance.
-
Modified dynamic time warping method applied to handwritten signature authenticity verification
PublicationA signature verification system based on static features and time-domain functions of signals obtained using a tablet has been presented in the paper. The signature verification method, based mainly on dynamic time warping coupled with some signature image features, has been described. The FRR measures reflecting the method’s efficiency have been evaluated for verification attempts performed directly after obtaining model signatures...
-
Comparative Study of the Reinforcement Type Effect on the Thermomechanical Properties and Burning of Epoxy-Based Composites
PublicationAramid (AF), glass (GF), carbon (CF), basalt (BF), and flax (FF) fibers in the form of fabrics were used to produce the composites by hand-lay up method. The use of fabrics of similar grammage for composites’ manufacturing allowed for a comprehensive comparison of the properties of the final products. The most important task was to prepare a complex setup of mechanical and thermomechanical properties, supplemented by fire behavior...
-
DYNAMIC POSITIONING CAPABILITY ASSESSMENT BASED ON OPTIMAL THRUST ALLOCATION
PublicationThe article presents an efficient method of optimal thrust allocation over the actuators in a dynamically positioned ship, according to the DNV-ST-0111 standard, Level 1. The optimisation task is approximated to a convex problem with linear constraints and mathematically formulated as quadratic programming. The case study is being used to illustrate the use of the proposed approach in assessing the DP capability of a rescue ship....
-
Modal analysis of a fish-belly flap type of steel water gate
PublicationABSTRACT: The results of a modal analysis of the fish-belly flap type of steel water gate are presented in the paper. The analysis was conducted for a detailed numerical model of the structure using four-node quadrilateral shell elements. The study was focused on the examination of the influence of positioning of the flap gate and hydrostatic pressure of water on the eigenvalues and eigenmodes of the structure. The results of the study...
-
Generating optimal paths in dynamic environments using RiverFormation Dynamics algorithm
PublicationThe paper presents a comparison of four optimisation algorithms implemented for the purpose of finding the shortest path in static and dynamic environments with obstacles. Two classical graph algorithms –the Dijkstra complete algorithm and A* heuristic algorithm – were compared with metaheuristic River Formation Dynamics swarm algorithm and its newly introduced modified version. Moreover, another swarm algorithm has been compared...
-
Dynamic Electrochemical Impedance Spectroscopy (DEIS) as a Tool for Analyzing Surface Oxidation Processes on Boron-Doped Diamond Electrodes
PublicationSurface oxidation processes play a key role in understanding electrochemical properties of boron-doped diamond (BDD) electrodes. The type of surface termination groups, which create the potential window of electrolytic water stability or hydrophobicity, influences such properties. In this study the kinetics of oxidation process under anodic polarization were studied in situ by means of Dynamic Electrochemical Impedance Spectroscopy...
-
SiC-based T-type modules for multi-pulse inverter with coupled inductors
PublicationThe paper presents SiC-based three-level T-type modules designed for a high-performance 30kVA DC/AC inverter operating at high frequency 85 kHz with low THD of the output voltage. This inverter system consists of two integrated parts. The first part is active and contains three parallelconnected three-phase T-type modules built with fast-switching SiC power transistors. The second, passive part of the system is a set of inductors...
-
Classifying type of vehicles on the basis of data extracted from audio signal characteristics
PublicationThe aim of this study is to find and optimize a feature vector for an automatic recognition of the type of vehicles, extracted form an audio signal. First, the influence of weather-based conditions of road surface on spectral characteristic of the audio signal recorded from a passing vehicle in close proximity to the road is discussed. Next, parameterization of the recorded audio signal is performed. For that purpose, the MIRtoolbox,...
-
Styrene-Butadiene Rubber/Modified Ground Tire Rubber Blends Co-Vulcanization: Effect of Accelerator Type
PublicationGround tire rubber was thermo-mechanically modified with using a co-rotating twin screw extruder. Modification of GTR was conducted in autothermal conditions. Styrene-butadiene rubber and modified ground tire rubber blends were prepared via two-roll milling. Obtained compounds were cured with conventional system (sulfur/vulcanization accelerator ratio was 2:1). During this research three commonly vulcanization accelerators (MBT,...
-
Simulation Tests of Working Press Loads under Pre-tensioned Body Conditions
Publication -
Loads of ship main diesel engine in the aspect of practical assessment of its operation
PublicationW artykule przedstawiono koncepcję metody pozwalającej na ocenę działania silnika pracującego na obciążeniu częściowym. Do określenia istniejącego zapasu parametrów użytkowych silnika oraz związanych z degradacją jego stanu technicznego dodatkowych kosztów ponoszonych przez użytkownika wykorzystane zostało wartościujące (ilościowe) ujęcie działania interpretowanego jako pewna wielkość fizyczna.
-
Sensitivity analysis of buckling loads of bisymmetric I-section columns with bracing elements
PublicationWyznaczono pierwsza wariacje siły krytycznej wyboczenia słupa o przekroju bisymetrycznym otwartym przy wariacji sztywnosci i połozenia stezen. Przyjeto załozenia klasycznej teorii pretów cienkosciennych o nieodkształcalnym przekroju poprzecznym. Analizowano zarówno stezenia boczne jak i stezenia ograniczajacespaczenie oraz skrecenie przekroju poprzecznego. Stezenia modelowano jako podpory sprezyste. W przykładzie numerycznym zbadano...
-
Operational loads of dredge pumps in their basic service states on selected types of dredgers
PublicationArtykuł przedstawia wyniki badań eksploatacyjnych dotyczący jednego z najważniejszych odbiorników energii mechanicznej na pogłębiarkach - pomp gruntowych. Badania eksploatacyjne obejmowały pomiary parametrów charakteryzujących obciążenia pomp gruntowych w dwóch podstawowych stanach ich eksploatacji, a mianowicie podczas załadunku ładowni gruntowej (pogłębiarki lub szalandy) oraz podczas refulowania gruntu na ląd.
-
Measurement of the earth fault loop impedance in a low voltage network with operating loads
PublicationW artykule przedstawiono problematykę dokładności pomiaru impedancji pętli zwarciowej w sieciach z obciążeniami roboczymi. Klasyczne metody pomiarowe i mierniki mogą powodować błędy pomiaru przekraczające dopuszczalną wartość. Z tego powodu może wystąpić ryzyko porażenia prądem elektrycznym, ponieważ przy doziemieniu nie będzie spełniony warunek samoczynnego wyłączenia zasilania. Błędy pomiaru w sieci z obciążeniami roboczymi można...
-
Vibration of the bridge under moving singular loads - theoretical formulation and numerical solution
PublicationThe paper presents the results of the numerical analysis of a simple vehicle passing over a simply supported bridge span. The bridge is modelled by a Euler-Bernoulli beam. The vehicle is modelled as a linear, visco-elastic oscillator, moving at a constant speed. The system is described by a set of differential equations of motion and solved numerically using the Runge-Kutta algorithm. The results are compared with the solution...
-
Spectral criterion of infinite fatigue life of beams under asymmetric random loads
PublicationRozpatrywana jest trwałość zmęczeniowa belek poddanych stałym i zmiennym obciążeniom osiowym, giętnym i skrętnym o znanych gęstościach widmowych mocy. Założono, że materiał posiada granicę zmęczenia i jest zgodny z modelem Kelvina-Voigta, oraz że składowe naprężenia są stacjonarne, stacjonarnie skorelowane i różniczkowalne w sensie średniokwadratowym. Zdefiniowano naprężenie równoważne i sformułowano kryterium nieograniczonej trwałości...
-
Spectral criterion of infinite fatigue life of beams under combined random loads
PublicationRozpatrywana jest trwałość zmęczeniowa belek poddanych zmiennym obciążeniom osiowym, giętnym i skrętnym o znanych gęstościach widmowych mocy i zerowych wartościach średnich. Założono, że materiał posiada granicę zmęczenia i jest zgodny z modelem Kelvina-Voigta, oraz że składowe naprężenia są stacjonarne, stacjonarnie skorelowane i różniczkowalne w sensie średniokwadratowym. Zdefiniowano naprężenie równoważne i sformułowano kryterium...
-
Possibility of defining of the average loads of main propulsion on the basis of ship design parameters.
PublicationZaprezentowano możliwość określania zależności między mocą holowania wybranych typów statków a średnim obciążeniem napędu głównego podczas pływania swobodnego. Przedstawione badania umożliwiają wyznaczenie średnich obciążeń napędu głównego podczas pływania swobodnego przy wykorzystaniu parametrów projektowych statku zawartych w założeniach armatorskich.
-
On numerical analysis of a thin-walled I-beam with warping stiffenes undertorsional loads
PublicationPraca jest streszczeniem referatu wygłoszonego na międzynarodowej konferencji Metody Komputerowe w Mechanice, Wisła, 3-6 czerwca 2003. Przedstawiono problem numerycznej analizy belek cienkościennych ze stężeniami. Omówiono dwa modele jednowymiarowe: jeden bazujący na koncepcji skupionej sztywności bimomentowej, a drugi na zastosowaniu superelementu MES. Otrzymane wyniki porównano z rezultatami analizy MES przy zastosowaniu dyskretyzacji...
-
The large rotations theory of elasto-viscoplastic shells subjected to thedynamic and thermal loads.
PublicationPrzedstawiono problemy sprężysto- lepkoplastycznej analizy geometrycznie nieliniowych płyt i powłok poddanych obciążeniom dynamicznym w różnych temperaturach. W obliczeniach zastosowano teorię ścinania pierwszego rzędu i konstytutywne prawo Chaboche´a w wariantach z uwzględnieniem wpływu temperatury na stałe materiałowe. Do całkowania równań ruchu użyto metody różnic centralnych, a do całkowania równań konstytutywnych regułę...
-
On delamination threshold loads in low velocity impact on glass-carbon/epoxy composites.
PublicationZbadano możliwości zastąpienia badań udarowych o niskiej energii ze spadającą masą badaniami quasi-statycznymi przy analogicznym obciążeniu próbki dla laminatów epoksydowych wzmocnionych włóknami węglowymi i szklanymi oraz węglowymi. Uzyskano dobrą zgodność wyników obu typów badań , co znajduje potwierdzenie w wynikach innych badaczy.
-
Analysis of data fusion algorithms for the vessel with the dynamic positioning system
PublicationThe dynamic positioning (DP) system on the vessel is operated to control the position and heading of the vessel with the use of propellers and thrusters installed on the board. On DP vessels redundant measurement systems of position, heading and the magnitude and direction of environmental forces are required for safety at sea. In this case, a fusion of data is needed from individual measurement devices. The article proposes a...
-
Non-linear static stability of bi-layer carbon nanosheets resting on an elastic matrix under various types of in-plane shearing loads in thermo-elasticity using nonlocal continuum
PublicationIn this research, the shear and thermal buckling of bi-layer rectangular orthotropic carbon nanosheets embedded on an elastic matrix using the nonlocal elasticity theory and non-linear strains of Von-Karman was studied. The bi-layer carbon sheets were modeled as a double-layered plate, and van der Waals forces between layers were considered. The governing equations and boundary conditions were obtained using the first order shear...
-
Superconductivity in a new intermetallic structure type based on endohedral Ta@Ir7Ge4 clusters
PublicationWe report the observation of superconductivity at a temperature near 3.5 K for the previously unreported compound TaIr2Ge2. In addition to being a superconductor, this material displays a new crystal structure type that contains endohedral clusters, as determined by single-crystal x-ray diffraction structure refinement; the structure is more complex than those of the commonly observed tetragonal 122 intermetallic phases. Despite...
-
Export diversification and economic development: a dynamic spatial data analysis
PublicationThis paper contributes to the empirical literature on the relationship between ‘export variety’ (export diversification) and economic development by relaxing the assumption of cross-country independence and allowing for spatial diffusion of shocks in observed and unobserved factors. Export variety is measured for a balanced panel of 114 countries (1992-2012) using very detailed information on their exports (HS 6-digit product...
-
Dynamic characteristics of the proton exchange membrane fuel cell module
PublicationThe paper describes a fuel cell based system and its performance. The system is based on two fuel cell units, DC/DC converter, DC/AC inverter, microprocessor control unit, load unit, bottled hydrogen supply system and a set of measurement instruments. In the study presented in the paper a dynamic response of the proton exchange membrane (PEM) fuel cell system to unit step change load as well as to periodical load changing cycles...
-
Neural modelling of dynamic systems with time delays based on an adjusted NEAT algorithm
PublicationA problem related to the development of an algorithm designed to find an architecture of artificial neural network used for black-box modelling of dynamic systems with time delays has been addressed in this paper. The proposed algorithm is based on a well-known NeuroEvolution of Augmenting Topologies (NEAT) algorithm. The NEAT algorithm has been adjusted by allowing additional connections within an artificial neural network and...
-
Polynomial description of dynamic impedance spectrogram—introduction to a new impedance analysis method
PublicationThis paper presents a polynomial description of spectrograms obtained using Dynamic Electrochemical Impedance Spectroscopy. A method to fit the polynomial degree correctly is discussed. A simple electrical system of a diode connected in parallel with a capacitor was used for testing. Dynamic impedance measurements during potentiodynamic polarization were conducted. This paper presents an alternative analysis method that allows...
-
Synthesis and Spectroscopic Characterization of Selected Phenothiazines and Phenazines Rationalized Based on DFT Calculation
PublicationTwo unique structures were isolated from the phosphorylation reaction of 10H-phenothiazine.The 5,5-dimethyl-2-(10H-phenothiazin-10-yl)-1,3,2-dioxaphosphinane 2-oxide (2a) illustrates theproduct of N-phosphorylation of phenothiazine. Moreover, a potential product of 2a instability,a thiophosphoric acid 2b, was successfully isolated and structurally characterized. Molecule 2a,similarly to sulfoxide derivative...
-
B-podand complexes with sodium ions: the reaction heats and PM5 semiempirical calculation
Publication -
Efficient calculation of the resonant frequencies of a SIW resonator with FDFD-based macromodel algorithm
PublicationW pracy przedstawiono efektywną metodę do analizy struktur ze integrowanym podłożem (SIW). W celu szybkiego obliczenia częstotliwości rezonansowych używany jest algorytm FDFD z zaimplementowanymi makromodelami.
-
A calculation proposal of labour time input when concreting in difficult atmospheric conditions
PublicationThe paper presents a selected proposal of establishing labour input in concreting jobs carried out in difficult atmospheric conditions.
-
THE PROBLEM OF THE CALCULATION OF THE FREQUENCY OF DIAGNOSTIC EXAMINATIONS BASED ON DEVICE’S PROPER OPERATION TIME
PublicationThe paper presents the proposal to apply the normal distribution to solve the problem of the frequency of diagnostic tests. Particular emphasis is placed on simplicity of the method. This method may be useful for the average user technical system. The method reduces the number of assumptions to a minimum. The results do not raise of serious doubts but they require verification of course.
-
Calculation of Vibrational Resonance Raman Spectra of Molecules Using Quantum Chemistry Methods
PublicationThe understanding and interpretation of experimental resonance Raman (RR) spectra can strongly benefit from theoretical simulations. These can be achieved by combining quantum chemistry (QC) methods to calculate the electronic and vibrational molecular properties, together with appropriate models and approximations to compute the Raman intensities. This chapter presents the main and most commonly employed approaches to calculate...
-
Verification of the new viscoelastic method of thermal stress calculation in asphalt layers of pavements
PublicationThe new viscoelastic method of thermal stress calculations in asphalt layers has been developed and published recently by the author. This paper presents verification of this method. The verification is based on the comparison of the results of calculations with results of testing of thermal stresses in Thermal Stress Restrained Specimen Test. The calculations of thermal stresses according to the new method were based on rheological...
-
The results of analyses of deep excavation walls using two different methods of calculation
PublicationPrzedstawiono wyniki obliczeń obudowy głębokiego wykopu dwukrotnie rozpieranej i dwukrotnie kotwionej w gruncie jednorodnym niespoistym. Obliczenia numeryczne wykonano metodą podpór sprężysto-plastycznych i metodą elementów skończonych. Zwrócono uwagę na istotne różnice w wynikach obliczeń. Zaproponowano wyjaśnienie przyczyn zaobserwowanych różnic w wynikach obliczeń otrzymanych z obu metod.
-
Calculation of electron scattering lengths on Ar, Kr, Xe, Rn and Og atoms
PublicationFocusing on the noble gases, we calculate the scattering potential using the Dirac-Coulomb Hamiltonian supplemented with a model polarization potential. We determine the scattering lengths using two methods, namely phase shifts for very small scattering energies and the shape of the wave function for zero scattering energy. We compare our theoretical electron scattering length results on Ar, Kr and Xe atoms with existing experimental...
-
The measurement and calculation of gas temperature inside a switchgear during fault arc period.
PublicationW artykule przedstawiono metodę obliczania temperatury gazu wewnątrz rozdzielnicy szczelnej z izolacją powietrzną podczas zwarć łukowych w oparciu o równanie przewodnictwa cieplnego. Przedstawiono wyniki badań eksperymentalnych temperatury gazów podczas zwarć z łukiem wędrującym. Opisano model do badań, układ probierczy i warunki badań. Wyniki obliczeń porównano z wynikami badań eksperymentalnych.