Search
Filters
total: 639
filtered: 588
Search results for: fermentation · recycling · waste-water · waste treatment and waste minimisation · evaporation · ozonation
-
Environmental impacts of food waste management technologies: A critical review of life cycle assessment (LCA) studies
PublicationFood waste is a serious global problem. Therefore, it is essential to reduce food waste and adopt recycling strategies to minimize its environmental impacts. However, conventional waste disposal methods emit harmful gases such as dioxin, CH4, N2O, and NH3, which contaminate the air and water resources. This work reviews the environmental consequences of food waste based on lifecycle assessment (LCA) techniques using methods such...
-
Comparison of Ozonation and Evaporation as Treatment Methods of Recycled Water for Bioethanol Fermentation Process
PublicationThe paper compared the performance of the ethanol yield after alcoholic fermentation with samples of rejected (RW) and permeate water (PW), RW and PW treated by oxidation with ozone (O3) (5 and 15 min) and evaporation, aiming the recirculation back to the bioethanol process. RW and PW were collected after an anaerobic bioreactor (AnBR) used for stillage treatment. Nine types of fermentations were made, where one used 100% tap...
-
Biowodór, „paliwo przyszłości”, dotychczasowe metody otrzymywania , porównanie metod otrzymywania
PublicationWodór jest ważnym pierwiastkiem w przemyśle chemicznym. Biowodór wydaje się być użytecznym odnawialnym nośnikiem energii, który mógłby zastąpić paliwa kopalne. Największym problemem wodoru jest jego rzadkie występowanie w czystej formie molekularnej H 2 . Dlatego otrzymanie biowodoru w objętościach opłacalnych ja ko surowiec czy biopaliwo wiedzie przez bioodpady „przesycone” wodorem. Każdy związek...
-
Microwave treatment in waste rubber recycling – recent advances and limitations
PublicationEnvironmentally-friendly microwave heating is increasingly used in polymer chemistry and technology. The selectivity and highly efficiency in the heat transfer present a huge advantage in systems based on recycling, improving their productivity and economic competitiveness. In case of the industrial recycling of waste rubbers, especially end-of-life tires, microwave-induced devulcanization and pyrolysis are nowadays considered...
-
Stabilizing lactate production through repeated batch fermentation of food waste and waste activated sludge
PublicationBio-valorization of organic waste streams, such as food waste and waste activated sludge, to lactic acid (LA) has recently drawn much attention. It offers an opportunity for resource recovery, alleviates environmental issues and potentially turns a profit. In this study, both stable and high LA yield (0.72 ± 0.15 g/g total chemical oxygen demand) and productivity rate (0.53 g/L•h) were obtained through repeated batch fermentation....
-
Recycling of Waste Rubber by Thermo-Mechanical Treatment in a Twin-Screw Extruder
PublicationRecycling of waste tires is a significant issue considering both environmental and economic aspects. One of the leading recycling routes is the shredding of tires resulting in the generation of ground tire rubber. This material can be easily introduced into various polymer matrices as a filler, reducing the use of conventionally applied petroleum-based materials. In such cases, it is essential to ensure sufficient interfacial compatibility,...
-
Special Issue on “Advanced Liquid Waste and Gas Waste Treatment Processes”
PublicationThe editorial contains a short review of the content of the Special Issue on waste gas and liquid streams treatment strategies.
-
A modern solid waste management strategy – the generation of new by-products
PublicationTo benefit the environment and society, EU legislation has introduced a ‘zero waste’ strategy, in which waste material should be converted to resources. Such legislation is supported by the solid waste hierarchy concept, which is a set of priorities in waste management. Under this concept, municipal solid waste plants (MSWPs) should be equipped with sorting and recycling facilities, composting/incineration units and landfill prisms...
-
Deep learning-based waste detection in natural and urban environments
PublicationWaste pollution is one of the most significant environmental issues in the modern world. The importance of recycling is well known, both for economic and ecological reasons, and the industry demands high efficiency. Current studies towards automatic waste detection are hardly comparable due to the lack of benchmarks and widely accepted standards regarding the used metrics and data. Those problems are addressed in this article by...
-
Recycling of waste tires in the light of binding law in Poland
PublicationA risings of large quantities of used rubber products, especially used tires has been increasing every year in Poland, in 2006 it was 160 thousand. The waste management and recycling of used tires become a major environmental problem. Well known methods of utilization of used tires are presented in this article. The main problem is ignorance of the law by tyre manufactures and users. In Poland first act on waste introduces ban...
-
Waste tire rubber devulcanization technologies: State-of-the-art, limitations and future perspectives
PublicationWaste tires management is a serious and global environmental problem. Therefore, searching for low-cost and industrial-scale applicable tire recycling methods is gaining more and more attention. Waste tire rubber is valuable source of secondary raw materials for the circular economy and current trends indicate that application of waste rubbers during manufacturing value-added products should increase in near future. Sustainable...
-
Surface Treatment of Rubber Waste
PublicationThis chapter deals with the study of different approaches to improve the compatibility of waste rubber with polymeric matrixes of high density polyethylene (HDPE) by using surface treatments to increase adhesion. Different surface treatments such as etching with sulphuric and nitric acids, the use of a silane as a coupling agent and chlorination with trichloroisocyanuric acid (TCI) have been applied. The modification of waste rubber...
-
Hydrogen production from wood waste by mean of dark fermentation
PublicationThe utilization of wood wastes in clean and green chemistry method like by mean of dark fermentation, is a highly desired solution of waste management. In the article model for the estimation hydrogen potential of wood waste is given. The model has been used to calculate the potential theoretical hydrogen mass that can be produced from wood wastes in Pomerania and Silesia: pine, spruce, fir, beech and oak. In the introduction,...
-
From polymer waste to potential main industrial products: Actual state of recycling and recovering
Publicationlastics have become widely used materials in everyday life due to their special properties such as durability, easy processing, light-weight and low-cost of production. However, because of their stable and non-biodegradable nature, postconsumer plastics become an issue to the environment. The growing amounts of waste are generated, as plastic products are commonly used only once before disposal. The alternatives of practical techniques...
-
Pre-treatment of bio fraction waste prior to fermentation processes
PublicationCurrent efforts are taken to increase resource efficiency, close material loops, and improve sustainable waste and by-products management. Thus, networking agro-food by-products and converting them into valuable products completely exhausting the potential of the raw material becomes significant. Model lignocellulosic and starch based biomass were subjected to pre-treatment with the application of acidic compounds, i.e. sulphuric...
-
Phosphorus concentration and availability in raw organic waste and post fermentation products
PublicationThe aim of the study was to determine the mobility of phosphorus forms in raw organic waste and from the solid and liquid fractions of digestate. To achieve the purpose of this study, the components (including livestock manure, agricultural waste, food waste, sewage sludge) and their post fermentation products were considered. Subsequently, the effect of the fermentation process on the mobility of phosphorus forms in post-fermentation fractions...
-
Pilot- scale plant for material recycling of whole waste tires
PublicationContinously growing demad for all kinds of vehicles and general tendency to regular exchange of tires are causing growth of scrap tires which need management. A risings of large quantities of used rubber products, especially used tires has been increasing every year in Poland, in 2006 it was 160 thousand. The waste management and recycling of used tires become a major environmental problem. It is worth noticing that tires which...
-
Influence of alkaline and oxidative pre-treatment of waste corn cobs on biohydrogen generation efficiency via dark fermentation
PublicationStages of waste corn cobs processing leading to the production of biohydrogen via dark fermentation are presented and discussed in this paper. Firstly, the effects of pretreatment conditions i.e. alkaline, alkaline-oxidizing and Fenton oxidizing pre-treatment of lignocellulosic biomass on the removal of lignin were examined. The solid residue obtained in the first stage was subjected to saccharification by means of enzymatic hydrolysis....
-
Fate and significance of phthalates and bisphenol A in liquid by-products generated during municipal solid waste mechanical-biological pre-treatment and disposal
PublicationSamples of liquid by-products generated by municipal solid waste plants (MSWPs) were tested for the presence of phthalates (PAEs) and bisphenol A (BPA). The results indicated that the wastewater generated during mechanical (sorting unit - SU) and biological (composting unit - CU) pre-treatment (MBT) of residual (mixed) solid waste is a significant source of these compounds. The concentrations of PAEs (up to 32222 lg/L) and BPA...
-
Waste tire rubber as low-cost and environmentally-friendly modifier in thermoset polymers – a review
PublicationNowadays, waste tire rubber (WTR) management is a growing and serious problem. Therefore, research works focused on the development of cost-effective and environmentally-friendly methods of WTR recycling are fully justified. Incorporation of WTR into polymer matrices and composite materials attracts much attention, because this approach allows sustainable development of industrially applicable waste tires recycling technologies....
-
Pyrolysis Process of Whole Waste Tires as a Biomass Energy Recycling
PublicationThe article is devoted to the description of material recycling of whole waste tires, including a new method of pyrolysis process, resulting in the final products: technically oil fractions (rubber plasticizer of rubber compounds) or diesel fuels (light, medium and heavy), activated carbon, gas fuel and steel scrap. Operational and performance tests of the first version of the pilot plant, consisting of three contributions cooperating...
-
Valorization of Bioplastic Waste: A Review on Effective Recycling Routes for the Most Widely Used Biopolymers
PublicationPlastics-based materials have a high carbon footprint, and their disposal is a considerable problem for the environment. Biodegradable bioplastics represent an alternative on which most countries have focused their attention to replace of conventional plastics in various sectors, among which food packaging is the most significant one. The evaluation of the optimal end-of-life process for bioplastic waste is of great importance...
-
Proposal of a mobile medical waste incinerator with automatic waste feeder and heat recovery system
PublicationThe paper presents and discusses the issue of medical waste (including hazardous ones) and their proper management. Inappropriate handling of infectious medical waste directly endangers the human being health and the environment. Infectious waste must therefore be properly disposed of – one of the most commonly used methods is the thermal treatment in the incinerators tailored for this purpose. During designing an incinerator unit,...
-
The Influence of Co-Fermentation of Agri-Food Waste with Primary Sludge on Biogas Production and Composition of the Liquid Fraction of Digestate
PublicationEnergy self-sufficiency is a current trend in wastewater treatment plants. This effect can be achieved by increasing the production of electricity from biogas and by reducing energy consumption for technological processes. One idea, in line with the circular economy concept, is the use of waste rich in organic matter as co-substrates for the fermentation process. The aim of this study was to determine the effect of waste co-fermentation...
-
Bioconversion of waste materials to hydrogen via dark fermentation using Enterobacter aerogenes
PublicationHydrogen can be obtained via dark fermentation with the use of anaerobic Enterobacter aerogenes. The efficiency of hydrogen production by fermentation techniques is strongly dependent on the con-ditions used i.e. the pH range, temperature, composition of fermentation broths, oxygen content, or even the presence of substances with potentially inhibitory effects on the microbiological culture [1-4]. The paper describes the study...
-
Particle size analysis of suspensions in removing of organic matter and phosphorus from waste water and surface water
PublicationIn this paper the particle size of suspended solids in the removing of organic matter and phosphorus compounds from lake- and waste- water treated in the Ecological Treatment Systems (ETS) was analyzed.The invesigated materials were taken from two ETS located in Pomerania Region/Poland. Object in Swarzewo is 3rd stage of biological treatment of municipal waste water, while object in Kartuzy has task to remove a phosphorus from...
-
Proposal of a Mobile Medical Waste Incinerator with Application of Automatic Waste Feeder and Heat Recovery System as a Novelty in Poland
PublicationThe paper presents and discusses the issues of medical waste (including hazardous ones) and the problems regarding their proper management in Poland. Inappropriate handling of infectious medical waste directly endangers human health and the environment. Infectious waste must be properly disposed of—in practice, the only method of their disposal available in Poland is a thermal treatment in the incinerators tailored for this purpose....
-
The Influence of Low-Temperature Disintegration on the Co-Fermentation Process of Distillation Residue and Waste-Activated Sludge
Publication: Innovative low-temperature disintegration (process temperature 55 ◦C and oxygen concentration 0.2 mg/dm3 ) can be an economically rational technology to intensifying energy production from renewable sources. The proposed process can achieve a degree of disintegration—under optimal conditions—of about 50%, which is excellent when compared with other methods of feed pre-treatment. The low-temperature disintegration of distillation...
-
Recycling of Waste Rubber by the Manufacturing of Foamed Polyurethane-Based Composites—Current State and Perspectives
PublicationWorn car tires are disruptive waste, and the issue of their management is crucial for the natural environment. In many countries, the primary method of end-of-life tires utilization is energy recovery. However, more effective and beneficial for the environment is material recycling. Using them for the production of polymer-rubber composites seems to be an auspicious direction of research. Incorporation of ground tire rubber into...
-
Waste Rubber Pyrolysis: Product Yields and Limonene Concentration
PublicationTires, conveyor belts, floor mats, and shoe soles form a main-stream of rubber waste. The amount of these used materials continuously increases due to development of the rubber market. Therefore, pro-ecological utilization (i.e., energy recycling instead of burning) and recovering valuable and recyclable materials becomes an urgent necessity. In this regard, this work was devoted to the chemical recycling of selected used rubber...
-
Waste Tyres Pyrolysis for Obtaining Limonene
PublicationThis review deals with the technologies of limonene production from waste tyre pyrolysis. Thermal decomposition is attractive for tackling the waste tyre disposal problem, as it enables both: energy to be recovered and limonene to be obtained. This material management recycling of tyres is environmentally more beneficial than the burning of all valuable products, including limonene. Given this recoverability of materials from waste...
-
Pre-Treatment of Furniture Waste for Smokeless Charcoal Production
PublicationThe aim of this study was to assess the possibility of using furniture waste for smokeless fuel production using the pyrolysis process. Four types of wood-based wastes were used in the pyrolysis process: pine sawdust (PS), chipboard (CB), medium-density fiberboard (MDF), and oriented strand board (OSB). Additionally, the slow and fast types of pyrolysis were compared, where the heating rates were 15 C/min and 100 C/min, respectively....
-
MINERAL MATTER IN MUNICIPAL SOLID WASTE
PublicationMunicipal solid waste (MSW) contains mineral materials which are seldom considered as a potential resource. Currently, the waste management sector pays attention to recyclable parts, biodegradable material, waste-to-energy fraction, and residues after waste reuse and recycle. In contrast, this study focus as on the mineral matter in MSW. The aim was to analyze and discuss the sources of mineral matter in MSW, the impact which the...
-
Vegetable derived-oil facilitating carbon black migration from waste tire rubbers and its reinforcement effect
PublicationThree dimensional chemically cross-linked polymer networks present a great challenge for recycling and reutilization of waste tire rubber. In this work, the covalently cross-linked networks of ground tire rubber (GTR) were degraded heterogeneously under 150 °C due to the synergistic effects of the soybean oil and controlled oxidation. The degradation mechanism was discussed using Horikx theory and Fourier transformation infrared...
-
The influence of different glycerine purities on chemical recycling process of polyurethane waste and resulting semi‐products
PublicationChemical recycling is the most favourable recycling method due to the possibility of polyol recovery. This work is dedicatedto the utilisation of crude glycerine and polyurethane waste. It aims at determining the impact of the use of glycerine fromthe production of biodiesel with various degrees of purity as a cleavage agent on the decomposition process of polyurethanefoam. The influence of glycerine purit y on the chemical structure...
-
Salinity enhances high optically active L-lactate production from co-fermentation of food waste and waste activated sludge: Unveiling the response of microbial community shift and functional profiling
PublicationLactic acid (LA), a versatile platform molecule, can be fermented from organic wastes, such as food waste and waste activated sludge. In this study, an efficient approach using salt, a component of food waste as an additive, was proposed to increase LA production. The LA productivity was increased at 10 g NaCl/L and optical pure L-lactate was obtained at 30 g NaCl/L. The enhancement of LA was in accordance with the increased solubilization...
-
Polyurethane-wood composites (PU-WC) as a method of wood waste management
PublicationIn recent years, due to the progressive environmental degradation and increase of environmental awareness, the sustainability of production systems in wood processing, the wood industry, and wood waste management is a crucial issue for European industry and society. Consequently, the problem of generating wood-like waste and the associated risks has become an increasingly noticeable challenge for science. Although various methods...
-
Recycling of Industrial Waste as Soil Binding Additives—Effects on Soil Mechanical and Hydraulic Properties during Its Stabilisation before Road Construction
PublicationTo improve the in situ soil stabilization, different chemical additives are used (ion exchange compounds, additives based on H2SO4 or vinyl polymers, and organic additives using lignosul- fonates). One interesting alternative is the production of additives from various waste materials. The extensive testing of waste-based blends with soil was performed; the mechanical (unconfined compressive strength (UCS)) and hydraulic (capillary...
-
A review on gasification and pyrolysis of waste plastics
PublicationGasification and pyrolysis are thermal processes for converting carbonaceous substances into tar, ash, coke, char, and gas. Pyrolysis produces products such as char, tar, and gas, while gasification transforms carbon-containing products (e.g., the products from pyrolysis) into a primarily gaseous product. The composition of the products and their relative quantities are highly dependent on the configuration of the overall process...
-
Ground Tire Rubber Filled Flexible Polyurethane Foam—Effect of Waste Rubber Treatment on Composite Performance
PublicationThe application range of flexible polyurethane (PU) foams is comprehensive because of their versatility and flexibility in adjusting structure and performance. In addition to the investigations associated with further broadening of their potential properties, researchers are looking for new raw materials, beneficially originated from renewable resources or recycling. A great example of such a material is ground tire rubber (GTR)—the...
-
Digestate Quality Originating from Kitchen Waste
PublicationThis paper examines the influence of biomass directed to anaerobic digestion on the quality of digestate, specifically focusing on the presence of undesirable substances, such as plastics, including biodegradable ones. It analyses the susceptibility of selected bioplastics to degradation and addresses the problem of reliable identification of microplastics in both feedstock—directed to anaerobic digestion—and produced digestate....
-
Sustainable utilization of copper post-flotation waste in cement composites
PublicationThe current way of managing the copper ore flotation waste is by placing it in waste neutralization facilities. However, flotation waste has great potential in application in cement composites. The article presents the detailed characteristics of post-flotation waste (PFW) and three types of cements: CEM I, CEM II/B-V, and CEM III/A, 42.5 MPa class. The post-flotation waste added for 20% of the cement mass increase the water demand...
-
Waste printer ink as modifier for natural rubber/carbon black composites: No haste, use waste
PublicationFrom a sustainability perspective, achieving a greener future with a minimal carbon footprint requires maximizing waste materials' reuse. The four pillars of satisfying customer demands are processing, price, properties, and performance. Along with such a global policy, this work seeks to utilize waste printer ink (WPI) as a source of carbon in combination with low- and high-surface carbon black (LCB and HCB, respectively) additives...
-
Waste materials assessment for phosphorus adsorption toward sustainable application in circular economy
PublicationPhosphorus is the main determinant of nutrient enrichment in the water bodies. Many resources including nutrients may be shortly exhausted, assuming current consumption. This scenario leads to growing interest in resources recovery and/or reuse, which together with sustainable energy consumption and waste reduction are the main courses of the circular economy. Usage of coagulants in wastewater treatment plants (WWTP) does not allow...
-
Application of industrial waste as a carbon source for biosurfactants production
PublicationBiosurfactants are natural surfactants produced by variety of microorganisms. They are very prospective product due to good biodegradability, low toxicity, good physicochemical properties and high efficiency in many applications. Moreover, they are efficient in wide range of pH, temperatures and salinity. However, the production of biosurfactants is very expensive due to high purification cost. This cost can be minimized by application...
-
Deep learning-based waste detection in natural and urban environments
Publication -
Ammonia amendment promotes high rate lactate production and recovery from semi-continuous food waste fermentation
PublicationIn this study, a reliable approach using ammonia nitrogen was proposed to increase lactate production during semi-continuous food waste (FW) fermentation under mesophilic conditions. Both free ammonia nitrogen (FAN) and ammonium ion (NH4+-N) were present in mesophilic reactors, with a wide FAN/NH4+-N ratio variation due to the intermittent pH control. The investigation of responsible mechanisms revealed that the increased production...
-
The impact of thermomechanical and chemical treatment of waste Brewers’ spent grain and soil biodegradation of sustainable Mater-Bi-Based biocomposites
PublicationDue to the massive plastic pollution, development of sustainable and biodegradable polymer materials is crucial to reduce environmental burdens and support climate neutrality. Application of lignocellulosic wastes as fillers for polymer composites was broadly reported, but analysis of biodegradation behavior of resulting biocomposites was rarely examined. Herein, sustainable Mater-Bi-based biocomposites filled with thermomechanically-...
-
Sustainable Waste Management for Implementation of a Circular Economy Model in a Port
PublicationThe manuscript presents the management of waste from marine vessels and cargo handling companies in a selected European Union port. The main objective of the paper is to analyse and evaluate the existing waste management model in the port of Szczecin in the context of circular economy. The expert research carried out is aimed, inter alia, at identifying which of the solutions currently in use need to be improved from an environmental...
-
Waste management in the mining industry of metals ores, coal, oil and natural gas - A review
PublicationWaste generated due to mining activity poses a serious issue due to the large amounts generated, even up to 65 billion tons per year, and is often associated with the risk posed by its storage and environmental management. This work aims to review waste management in the mining industry of metals ores, coal, oil and natural gas. It includes an analysis and discussion on the possibilities for reuse of certain types of wastes generated...
-
From polystyrene waste to porous carbon flake and potential application in supercapacitor
Publication -
The effect of agro-waste co-digestion and sludge disposal on carbon footprint in municipal wastewater treatment plants
PublicationThe study presents analysis of the carbon footprint (CF) in 6 wastewater treatment plants in northern Poland with a special focus on the effect of co digestion of sewage sludge and food waste. Although co-digestion increases the on-site energy production, but it has a negative effect on the total CF. To overcome the negative effect, several sludge disposal scenarios were analysed and their effect on the CF reduction was determined....
-
Exergy analysis of the Szewalski cycle with a waste heat recovery system
PublicationThe conversion of a waste heat energy to electricity is now becoming one of the key points to improve the energy efficiency in a process engineering. However, large losses of a low-temperature thermal energy are also present in power engineering. One of such sources of waste heat in power plants are exhaust gases at the outlet of boilers. Through usage of a waste heat regeneration system it is possible to attain a heat rate of approximately...
-
Environmentally friendly polymer-rubber composites obtained from waste tyres: A review
PublicationThe paper is transdisciplinary. The complex overview on changes in policy and approach to waste tyres that leads to both solving environmental problem of post consumer tyres and creating environmentally friendlier novel materials are presented. It is shown that in the world, the amount of polymer wastes increases every year. Most of them are in the form of post-consumer tyres. Recycling and recovery of such tyres is a serious environmental...
-
Recent Advances in Development of Waste-Based Polymer Materials: A Review
PublicationLimited petroleum sources, suitable law regulations, and higher awareness within society has caused sustainable development of manufacturing and recycling of polymer blends and composites to be gaining increasing attention. This work aims to report recent advances in the manufacturing of environmentally friendly and low-cost polymer materials based on post-production and postconsumer wastes. Sustainable development of three groups...
-
CURRENT TRENDS IN RECYCLING OF PHOTOVOLTAIC SOLAR CELLS AND MODULES WASTE
PublicationIn comparison to other energy producing techniques, photovoltaics (PV) is one of the most promising options: no emission of any matter into the environment during operation; extremely long operation period (estimated average: 25 years), minimum maintenance, robust technique, aesthetic aspects. The use of photovoltaics is rapidly increasing, and the respective market is developing accordingly. Although PV manufacturing equipment...
-
Thermoplastic polyurethanes with glycolysate intermediates from polyurethane waste recycling
PublicationThe polyol is a major component in polyurethane formulations and therefore introducing to the formulation recycled polyol (obtained during decomposition process) allows decreasing the usage of pure petrochemical components. In this work, thermoplastic polyurethanes were prepared using various mixtures of a petrochemical macrodiol poly(ethylene-butylene adipate)diol (PEBA) and a recycled glycolysate intermediate, called glycolysate...
-
Polypropylene structure alterations after 5 years of natural degradation in a waste landfill
PublicationUp to 25% of plastic waste in Europe is still disposed of in landfills, despite recycling efforts. The plastic waste in the landfill plot may be exposed both to abiotic and biotic degradation processes, although it is thought that most of the plastic materials tend to be resistant to biodegradation or biodeterioration even after a long time. To verify if polypropylene (PP) can undergo the process of short-term biodegradation and...
-
The Influence of the Chemical Composition of Selected Waste Materials from the Production of Copper on the Final Environmental Assessment
PublicationThis article presents qualitative and quantitative analysis of the waste produced by KGHM Polska Miedź. The waste has been analyzed according to its chemical composition and balanced in order to be reused and recycled. Special attention has been paid to mining industries producing the biggest amount of waste and ore enrichment businesses generating waste, which isn’t reused nowadays. Laboratory reseach has been conducted on floatation...
-
Expermental investigation on adsorption of methylene blue dye from waste water using corncob cellulose-based hydrogel
PublicationHydrogel from corncob cellulose was synthesized in this investigation. The synthesized Hydrogel was characterized by SEM, XRD, and FTIR instruments. As the results indicate the synthesized hydrogel has required and important features, these suggest the suitability of hydrogel for the adsorption of methylene blue dye (MBD). Three important process variables (dosage, contact time, and initial concentration) with three levels were...
-
Pyrolysis Combined with the Dry Reforming of Waste Plastics as a Potential Method for Resource Recovery—A Review of Process Parameters and Catalysts
Publication: Emissions of greenhouse gases and growing amounts of waste plastic are serious environmental threats that need urgent attention. The current methods dedicated to waste plastic recycling are still insufficient and it is necessary to search for new technologies for waste plastic management. The pyrolysis-catalytic dry reforming (PCDR) of waste plastic is a promising pro-environmental way employed for the reduction of both CO2 and...
-
Occupational exposure to anaerobic bacteria in a waste sorting plant
Publication -
Management of ground tire rubber waste by incorporation into polyurethane-based composite foams
PublicationRapid economic growth implicated the developing multiple industry sectors, including the automotive branch, increasing waste generation since recycling and utilization methods have not been established simultaneously. A very severe threat is the generation of enormous amounts of post-consumer tires considered burdensome waste, e.g., due to the substantial emissions of volatile organic compounds (VOCs). Therefore, it is essential...
-
Overcoming carboxylic acid inhibition by granular consortia in high-load liquefied food waste fermentation for efficient lactate accumulation
PublicationGranular sludge, a self-aggregating spherical biofilm, possesses better stability compared to flocculent sludge under extreme conditions. This study compared the ability of anaerobic granular sludge (AnGS) and flocculent waste activated sludge (WAS) to convert food waste (FW) into highly-valuable optically active lactic acid (LA), a central and versatile intermediate platform molecule. Different loadings (30–60 g volatile suspended...
-
Thermogravimetric analysis/ pyrolysis of used tyres and waste rubber
PublicationThe process of pyrolysis is investigated in this paper. The pyrolysis results of two samples: waste tyres and rubber at different heating rates (10, 20, 50 K/min), were compared. In other experiments the degradation of two pyrolysis products, char and oil was examined. The kinetic study using the thermogravimetry equipment (TG) was done, which allowed determination of the kinetic mechanism of the process. The elemental analysis...
-
Waste tire rubber as low-cost and environmentally-friendly modifier in thermoset polymers – A review
Publication -
A mixture of cellulose production waste with municipal sewage as new material for an ecological management of wastes
PublicationChemical contaminants present in cellulose production waste and municipal sewage sludge condition the necessity to treat these wastes before they are introduced into the environment. Environmental use of the these wastes appears to be justified owing to the content of organic substances as well as the considerable fertilising value. The aim of the study was to assess chemical composition and ecotoxicity of cellulose production...
-
The Air and Sewage Pollutants from Biological Waste Treatment
Publication -
Pyrolysis of Waste Biomass: Technical and Process Achievements, and Future Development-A Review
PublicationPyrolysis has been applied in the human economy for many years, and it has become a significant alternative to the production of chemical compounds, including biofuels. The article fo-cuses mostly on recent achievements in the technical and processing aspects of pyrolysis. The aim of the review is to present the latest research on the process of waste biomass pyrolysis to fuel production. The paper describes the mechanisms of...
-
Mater-Bi/Brewers’ Spent Grain Biocomposites—Novel Approach to Plant-Based Waste Filler Treatment by Highly Efficient Thermomechanical and Chemical Methods
PublicationThermoplastic starch (TPS) is a homogenous material prepared from native starch and water or other plasticizers subjected to mixing at a temperature exceeding starch gelatinization temperature. It shows major drawbacks like high moisture sensitivity, poor mechanical properties, and thermal stability. To overcome these drawbacks without significant cost increase, TPS could be blended with bio-based or biodegradable polymers and...
-
Study on some of the strength properties of soft clay stabilized with plastic waste strips
PublicationIt is well known that if plastic wastes are not well managed, it has a negative impact on the environment as well as on human health. In this study, recycling plastic waste in form of strips for stabilizing weak subgrade soil is proposed. For this purpose, a weak clay soil sample was mixed with 0.2%, 0.3%, and 0.4% of plastic strips by weight of soil, and the experimental results were compared to the control soil sample with 0%...
-
Efficiency and proportions of waste tyre pyrolysis products depending on the reactor type—A review
PublicationThis article discusses the current use of different pyrolytic reactors, their constructions and operating principles regarding the yields of main products of waste tyre pyrolytic recycling. Whether one makes a larger or smaller profit, or even a loss due to a surcharge being levied on waste tyre recycling, depends on the sale of the pyrolysis products (gas, char, oil), the proportions and market prices of which differ. The cheapest...
-
Determining the Mechanical Properties of Solid Plates Obtained from the Recycling of Cable Waste
Publication -
Removal of BTEX Compounds From Waste Gases; Destruction and Recovery Techniques
PublicationThe tendency for BTEX compounds (benzene, toluene, ethylbenzene, xylenes) to spread into all compartments of the environment together with their influence on both ecosystem and human health means that the emission of thesecompounds into the air is becoming the matter of worldwide concern. The legal regulations introduced by the European Union governing the assessment and management of air quality obliges member states to systematically...
-
Mechanical Behavior of Plastic Strips-Reinforced Expansive Soils Stabilized with Waste Marble Dust
PublicationExpansive soil needs to undergo treatment to be used as safe foundation soil for roads and buildings. From environmental conservation and economical point of view, the usage of agricultural and industrial wastes is the best option. In this study, the effects of utilizing plastic waste and marble waste dust on the engineering properties of expansive soils were examined. Various laboratory tests were carried out on sampled expansive...
-
Mechanical Behavior of Plastic Strips-Reinforced Expansive Soils Stabilized with Waste Marble Dust
PublicationExpansive soil needs to undergo treatment to be used as safe foundation soil for roads and buildings. From an environmental conservation and economical point of view, the usage of agricultural and industrial wastes is the best option. In this study, the effects of utilizing plastic waste and marble waste dust on the engineering properties of expansive soils were examined. Various laboratory tests were carried out on sampled expansive...
-
Template-based textural modifications of polymeric graphitic carbon nitrides towards waste water treatment
Publication -
Modification of thermal and rheological characteristics of bitumen by waste PET/GTR blends
PublicationWaste poly(ethylene terephthalate) (wPET)/ground tire rubber (GTR) blends with variable compositions were applied as low-cost modifiers into bitumen and their performance has been evaluated via morphological, thermal and rheological analyses. Depending on the weight ratio of wPET/GTR, dispersion of single/composite domains of waste polymers in the bitumen has promoted the interaction between bitumen and blend components. Fourier...
-
Utilization of Gaseous Carbon Dioxide and Industrial Ca-rich Waste for Calcium Carbonate Precipitation: A Review
PublicationTechnologies for the management of various types of waste and the production of useful products from them are currently widely studied. Both carbon dioxide and calcium-rich waste from various production processes are problematic wastes that can be used to produce calcium carbonate. Therefore, the purpose of this paper is to provide an overview about the state of the development of processes that use these two wastes...
-
Analysis of possibility and purposefulness of application of waste-heat boilers to trailing suction hopper dredgers
PublicationThis paper presents an analysis of possibility and purposefulness of application of waste-heat boilers to trailing suction hopper dredgers. Using results of own operational research on dredgers this author determined thermal power demand for six hypothetical trailing suction hopper dredgers of various size, at accounting for a type of power system and kind of fuel combusted by dredger's power plant. By means of basic indices of...
-
Harmful biological agents in municipal waste thermal treatment plants
Publication -
Utilisation of waste heat from the power plant by use of the ORC aided with bleed steam and extra source of heat
PublicationUtilization of waste heat recovered from the exhaust gases of the power generation unit by means of ORC (organic Rankine cycles) installation is considered. The waste heat is available in the form of a stream of hot water having temperature of 90 stC in the amount of 200 MWt. To increase evaporation temperaturę of ORC working fluid the heat of steam from the extraction points from the low-pressure part of steam turbine is used....
-
Sustainable recycling of waste polystyrene into hierarchical porous carbon nanosheets with potential applications in supercapacitors
Publication -
Chemical recycling of plastic waste as a mean to implement the circular economy model in the European Union
Publication -
Recycling of Polyurethanes Containing Flame-Retardants and Polymer Waste Transformed into Flame-Retarded Polyurethanes
PublicationThe growing number of polyurethanes (PUs) produced every year has developed methods for their mechanical and chemical recycling which yield valuable products like substitutes for commercial polyols or flame-retardants. PUs can be produced in different shapes and forms (i.e., elastomers, flexible or rigid foams, coatings, etc.) using several different components (i.e., di- or polyisocyanates, ester- or ether-based polyols, low-molecular...
-
Design and experimental investigations of a cylindrical microjet heat exchanger for waste heat recovery systems
PublicationCompact heat exchangers have more and more applications in many areas, including the HVAC, food and petrochemical industry. This paper describes the development of heat exchanger technology for waste heat recovery (WHR) from a range of processes. Case-study testing shows that the proposed heat exchanger can successfully enhance heat transfer and recover waste heat in a range of applications making them economically, environmentally and...
-
Structural Assessment of Reinforced Concrete Beams Incorporating Waste Plastic Straws
PublicationThe behavior of reinforced concrete beams containing fibers made of waste plastic straws (WPSs) under the three point bending test is examined. The effect of WPS fiber addition on the compressive and split tensile strength is reported. Four concrete mixes were prepared. The control mix PS-0 had a proportion of 1 cement: 1 sand: 2 coarse aggregate and a water cement ratio of 0.4. In the other three mixes PS-0.5, PS-1.5 and PS-3,...
-
Applications of permeability, oedometer and direct shear tests to the sand mixed with waste tire crumb
PublicationThe amount of the used waste rubbers in the world has been increasing every year, and their utilization, become a major environmental problem worldwide. The present experimental work has been performed to investigate the influence of rubber inclusion on the behavior of a sand. Geotechnical properties of the sand, and sand with tire crumb at various ratios mixtures (0%, 2.5%, 7.5%, and 15%) were investigated through a series of...
-
Chemical pollution and toxicity of water samples from stream receiving leachate from controlled municipal solid waste (MSW) landfill
PublicationThe present study was aimed to determine the impact of municipal waste landfill on the pollution level of surface waters, and to investigate whether the choice and number of physical and chemical parameters monitored are sufficient for determining the actual risk related to bioavailability and mobility of contaminants. In 2007–2012, water samples were collected from the stream flowing through the site at two sampling locations,...
-
Conversion of waste biomass to designed and tailored activated chars with valuable properties for adsorption and electrochemical applications
PublicationWaste biomass, a renewable energy source, is inexpensive material that has great potential in sorp-tion and electrochemical application. The selected waste materials (corncobs, coconut shells, wal-nuts, and pistachio husks) allow to close the production cycle and enable material recycling, which are important aspects in the hierarchy of waste management. The proposed methodology for pro-duction and activation of biochars can be...
-
Mobility and biodegradability of an imidazolium based ionic liquid in soil and soil amended with waste sewage sludge
PublicationSorption on solids and biodegradation are main phenomena that can mitigate the pollution of soil and water by ionic liquids (ILs). ILs sorbed on soil particles become immobilized (temporarily or permanently) which prevents them from spreading into deeper layers of soil or groundwater but which also makes them less bioavailable. In this study we attempt to examine if amendment of soil with waste sludge has a potential to mitigate...
-
Valorization of waste cabbage leaves by postharvest photochemical treatments monitored with a non-destructive fluorescence-based sensor
PublicationThe biosynthesis of polyphenolic compounds in cabbage waste, outer green leaves of white head cabbage (Brassica oleracea L. var. capitata subvar. alba), was stimulated by postharvest irradiation with UVB lamps or sunlight. Both treatments boosted the content of kaempferol and quercetin glycosides, especially in the basal leaf zone, as determined by the HPLC analysis of leaf extracts and by a non-destructive optical sensor. The...
-
Mass production of hierarchically porous carbon nanosheets by carbonizing “real-world” mixed waste plastics toward excellent-performance supercapacitors
Publication -
The effectiveness of the mechanical treatment of municipal waste using the example of a selected installation
Publication -
Coffee Silverskin as a Multifunctional Waste Filler for High-Density Polyethylene Green Composites
PublicationThis work aims to describe the coffee silverskin effect as a lignocellulosic waste filler for high-density polyethylene (HDPE) composites development. The main task was to determine various modification effects resulting from the complex chemical composition of coffee silverskin containing compounds with potential antioxidative properties, including caffeine, polyphenols, tannins, or melanoidins. The processing, thermal, physicochemical,...
-
Production of fuel briquette from solid waste biomass using natural resin as a binder
PublicationBackground: This research aimed to evaluate the use of natural resin as a binder for the production of fuel briquette from solid waste biomass.Methods: Proximate analyses were made for fuel briquette prepared from solid waste biomass using natural resin as a binder in comparison with using starch as a binder.Results: The results for density, percent content of moisture, percent content of volatile matter, percent...
-
Production of fuel briquette from solid waste biomass using natural resin as a binder
PublicationAbstract Background: This research aimed to evaluate the use of natural resin as a binder for the production of fuel briquette from solid waste biomass. Methods: Proximate analyses were made for fuel briquette prepared from solid waste biomass using natural resin as a binder in comparison with using starch as a binder. Results: The results for density, percent content of moisture, percent content of volatile matter, percent content...
-
Utilization of waste chloroorganic compounds
Publication -
Pyrolysis as an alternative for combustion of waste
PublicationProces pirolizy polega na rozkładzie materii organicznej w podwyższonej temperaturze w warunkach beztlenowych, dlatego może być on stosowany jako alternatywa lub uzupełnienie dla procesu spalania. Piroliza pozwala na uzyskanie substancji chemicznych z polimerów naturalnych i syntetycznych. W umiarkowanej temperaturze (300 - 500 ° C), można uzyskać wysokiej wydajności frakcji ciekłej, natomiast wysokie temperatury sprzyjają powstawaniu...
-
Ammonium Enhances Food Waste Fermentation to High-Value Optically Active l-Lactic acid
Publication