displaying 1000 best results Help
Search results for: LOW TEMPERATURE CRACKING
-
Dynamic mass measurement in checkweighers using a discrete time-variant low-pass filter
PublicationConveyor belt type checkweighers are complex mechanical systems consisting of a weighing sensor (strain gauge load cell, electrodynamically compensated load cell), packages (of different shapes, made of different materials) and a transport system (motors, gears, rollers). Disturbances generated by the vibrating parts of such a system are reflected in the signal power spectra in a form of strong spectral peaks, located usually in...
-
The use of thermal imaging camera to estimate velocity profiles based on temperature distribution in a free convection boundary layer
PublicationThis work describes an attempt to assess whether the temperature field from a thermal imaging camera can be converted into a velocity field with an accuracy sufficient for qualitative conducting or describing the phenomenon, i.e. when the Navier-Stokes, Fourier-Kirchhoff and continuity equations are mutually coupled. The consequence of this link between temperature fields and velocity is the possibility to formulate the hypothesis...
-
EXHAUST GAS TEMPERATURE MEASUREMENTS IN DIAGNOSTICS OF TURBOCHARGED MARINE INTERNAL COMBUSTION ENGINES PART II DYNAMIC MEASUREMENTS
PublicationThe second part of the article describes the technology of marine engine diagnostics making use of dynamic measurements of the exhaust gas temperature. Little-known achievements of Prof. S. Rutkowski of the Naval College in Gdynia (now: Polish Naval Academy) in this area are presented. A novel approach is proposed which consists in the use of the measured exhaust gas temperature dynamics for qualitative and quantitative assessment...
-
Measurement of complex refractive index of human blood by low-coherence interferometry
PublicationIn this article, the usefulness of the optical technique for measurements of blood complex refractive index has been examined. Measurement of optical properties of human blood is difficult to perform because of its nonuniform nature. However, results of my investigation have shown the usefulness of low-coherencei nterferometry for measurement complex refractive index of human blood. Furthermore, mathematical analysis of spectrum...
-
Mechanism of Reduced Sintering Temperature of Al2O3–ZrO2 Nanocomposites Obtained by Microwave Hydrothermal Synthesis
PublicationA novel method to obtain Al2O3–ZrO2 nanocomposites is presented. It consists of the co-precipitation step of boehmite (AlO(OH)) and ZrO2, followed by microwave hydrothermal treatment at 270 ◦ C and 60 MPa, and by calcination at 600 ◦ C. Using this method, we obtained two nanocomposites: Al2O3–20 wt % ZrO2 and Al2O3–40 wt % ZrO2. Nanocomposites were characterized by Fourier transformed infrared spectroscopy, Raman spectroscopy,...
-
High-Temperature Tensile Behaviour of GTAW Joints of P92 Steel and Alloy 617 for Two Different Fillers
PublicationThis study explores the high-temperature (HT) tensile rupture characteristics of a dissimilar gas-tungsten-arc-welded (GTAW) joint between P92 steel and Alloy 617, fabricated using ER62SB9 and ERNiCrCoMo-1 fillers. The high-temperature tensile tests were performed at elevated temperatures of 550 ◦C and 650 ◦C. An optical microscope (OM) and a field emission scanning electron microscope (FESEM) were utilized to characterize the...
-
3D PCB package for GaN inverter leg with low EMC feature
PublicationThis paper presents the adaptation of a 3D integration concept previously used with vertical devices to lateral GaN devices. This 3D integration allows to reduce loop inductance, to ensure more symmetrical design with especially limited Common Mode emission, thanks to a low middle point stray capacitance. This reduction has been achieved by both working on the power layout and including a specific shield between the devices and...
-
Liking low-status? Contextual and individual differences in attributional biases of low-status outgroup members
Publication -
Potential reduction of traffic noise by the means of increased fleet of electric vehicles using a combination of low-noise tyres and low-noise road surfaces
PublicationIn the future, the number of zero-emission vehicles like electric and plug-in hybrid vehicles (in electric mode) is expected to be a substantial part of the vehicle fleet. In Norway, such vehicles already account for approximately 20 % of all new cars sold. Since these vehicles emit negligible noise related to the power-train, the tyre/road noise is the dominating noise source. In the LEO project, tyres designed for such cars have...
-
The measurement of input power of power supply in network disturbed by low frequency distortions
PublicationIn the paper authors present results of observation of input power changes versus harmonics amplitude in supply voltage of low-power power supply device. In the study, the electrical measurements supported with thermal imaging were used. The input circuit elements of studied device responsible for input power increase are pointed
-
On the tendency of temperature and electric field dependences of interface recombination in P3HT:PCBM organic bulk heterojunction solar cells
PublicationWe demonstrate theoretical explanation of the temperature and electric field dependences of recombination coefficients in an organic P3HT:PCBM bulk heterojunction solar cell. Based onthe model of interface recombination, two analytical formulas describing the relative ratio of the interface (γI ) to the Langevin (γL) recombination coefficients have been derived. Our analysis indicates that the sign of parameters φT and φF determines...
-
Design analysis of Tesla micro-turbine operating on a low-boiling medium
PublicationThis paper presents results of the design analysis of a Tesla bladeless turbine intended for a co-generating micro-power plantof heat capacity 20 kW, which operates in an organic Rankine cycle on a low-boiling medium. Numerical calculations of flowin several Tesla turbine models were performed for a range of design parameters. Results of investigations exhibit interestingfeatures in the distribution of flow parameters within the...
-
TRAVELLING WAVES FOR LOW–GRADE GLIOMA GROWTH AND RESPONSE TO A CHEMOTHERAPY MODEL
PublicationLow-grade gliomas (LGGs) are primary brain tumours which evolve very slowly in time, but inevitably cause patient death. In this paper, we consider a PDE version of the previously proposed ODE model that describes the changes in the densities of functionally alive LGGs cells and cells that are irreversibly damaged by chemotherapy treatment. Besides the basic mathematical properties of the model, we study the possibility of the...
-
PROCESSING, MECHANICAL AND THERMAL PROPERTIES OF RECYCLED LOW-DENSITY POLYETHYLENE STREAMS
PublicationThe recycling of plastics is currently one of the most significant industrial challenges. Due to the enormous amounts of plastic wastes generated by various industry branches, it is essential to look for the potential methods of their utilization. Nevertheless, for the efficient application of recycled materials it is crucial to analyze their performance. Therefore, in presented paper we investigated the processing (melt flow index),...
-
High temperature monoclinic-to-tetragonal phase transition in magnesium doped lanthanum ortho-niobate
PublicationMagnesium doped lanthanum ortho-niobate (La0.98Mg0.02NbO4) was prepared by the molten salt synthesis method. X-ray diffraction and dilatometry methods were used to study high temperature behavior of the ceramic material. Special attention was paid to the phase transition between the monoclinic and tetragonal phases. The values of spontaneous strain on the basis of unit cell parameter, obtained by Rietveld refinement, have been...
-
The effects of offshoring to low-wage countries on domestic wages: a worldwide industrial analysis
PublicationThis paper extends the literature on the implications of offshoring for labour markets by investigating its effect on the wages of different skill groups in a broad global context. The analysis draws on input–output data from the WIOD project, and in the panel analysed (13 manufacturing industries, 40 countries, 1995–2009) we account for up to 96 % of the international trade in manufacturing inputs. Being particularly interested...
-
Research on the effect of low-sulphur marine fuels on the dynamic characteristics of a CI engine
PublicationThe implementation of low-sulphur, so-called modified marine fuels into operation requires prior labora- tory engine tests to assess the energy, emission and structural effects of their usage. This type of research are carried out on the test bed of a diesel engine as a small-scale physical model that reproduces the adequate design and process (parametric) features of a full-size marine engine. Their key stage is to determine the energy...
-
Maciej Wierzbowski dr inż.
People -
Jamming and jamming mitigation for selected 5G military scenarios
PublicationThis paper presents jamming and jamming mitigation techniques, which can be used in relation to emerging military systems based on fifth-generation (5G) technology. Nowadays, 5G technology provides incremental improvements over Long Term Evolution (LTE) networks resulting in the enhancement of civilian communications. Considering enormous possible applications of this new technology, it is feasible to use them in military utilities....
-
A low complexity double-talk detector based on the signal envelope
PublicationA new algorithm for double-talk detection, intended for use in the acoustic echo canceller for voice communication applications, is proposed. The communication system developed by the authors required the use of a double-talk detection algorithm with low complexity and good accuracy. The authors propose an approach to doubletalk detection based on the signal envelopes. For each of three signals: the far-end speech, the microphone...
-
Interaction of low energy electrons with formic acid monomer, dimer and trimer
PublicationConfigurations of the formic acid monomer, dimer and trimer are presented. We have calculated the total energies for these structures. We have considered also the negatively charged clusters and discussed the possible pathways of interaction of low energy electrons with monomers and clusters. Calculations have been executed using 6-311G** and 6-311++G** basis sets. The electron affinities of monomer and clusters are presented....
-
The hydration of selected biologically relevant molecules – the temperature effect on apparent molar volume and compression
PublicationThe densities and sound velocities at T = (288.15, 293.15, 298.15, 303.15 and 308.15) K were measured for aqueous solutions of glycine, trimethylamine-N-oxide, taurine and N-methylacetamide. From these data, the apparent molar volumes, V the apparent molar isentropic compressions, KS,, and the Passynski hydration numbers of solutes were determined. The concentration dependencies of the calculated quantities, their limiting values...
-
Diagnostic tolerances' evaluation method of the start-up exhaust temperature of a naval gas turbine
PublicationThe conducted investigations aimed to elaborate the method of marking diagnostic tolerances of the exhaust temperature of a gas turbine observed during engine's start-up process. The diagnostic tolerances were determined by means of statistical inference by creating the hypothesis about a normal distribution of the start-up exhaust temperature's dispersion in the initial operation moment, which was subsequently verified applying...
-
Chemical analysis of low carbon content coals and their applications as dye adsorbent
PublicationCoal is primarily a fuel material but lately it has been utilized as an adsorbent for removing toxic metal ions. However, its usage for removing organic pollutants is not well studied. We report here a systematic study on the use of coal samples of varying carbon contents as adsorbents for removing Basic Blue 41 as a model cationic dye. The coal samples were collected from coal mines and were thoroughly characterized. The concentrations...
-
Performance of the PEM fuel cell module. Part 2. Effect of excess ratio and stack temperature
PublicationThe paper describes a fuel cell based system performance under different thermal conditions. The system could be fed with bottled hydrogen or with very high purity hydrogen obtained from reforming of methanol. The system is based on two fuel cell units (1.2 kW each, produced by Ballard Power Systems Inc. and called Nexa), DC/DC converter, DC/AC inverter, microprocessor control unit, load unit, bottled hydrogen supply system and...
-
Measurement of temperature-dependent viscosity and thermal conductivity of alumina and titania thermal oil nanofluids
PublicationThe results of simultaneous measurements of dynamic viscosity, thermal conductivity, electrical conductivity and pH of two nanofluids, i.e. thermal oil/Al2O3 and thermal oil/TiO2 are presented. Thermal oil was selected as a base liquid because of possible application in ORC systems as an intermediate heating agent. Nanoparticles were tested at the concentration of 0.1%, 1% and 5% by weight within temperature range from 20°C to...
-
Miniaturization of ESPAR Antenna Using Low-Cost 3D Printing Process
PublicationIn this paper, the miniaturized electronically steerable parasitic array radiator (ESPAR) antenna is presented. The size reduction was obtained by embedding its active and passive elements in polylactic acid (PLA) plastic material commonly used in low-cost 3D printing. The influence of 3D printing process imperfections on the ESPAR antenna design is investigated and a simple yet effective method to compensate them has been proposed....
-
Low-Profile ESPAR Antenna for RSS-Based DoA Estimation in IoT Applications
PublicationIn this paper, we have introduced a low-profile electronically steerable parasitic array radiator (ESPAR) antenna that can successfully be used to estimate the direction-of-arrival (DoA) of incoming signals in wireless sensor network (WSN) applications, in which the height of the complete antenna has to be low. The proposed antenna is over three times lower than high-profile ESPAR antenna designs currently available in the literature...
-
High precision and accuracy using low cost GNSS receivers and supporting technologies
PublicationThis chapter focuses on methods and techniques of positioning, based on the highly accurate and precise Global Navigation Satellite System (GNSS), which are available at a relatively low price. In this context, a comparison of different positioning methods provided by the free and open source software (FOSS) package called RTKLIB is given. Other aspects related to price reduction are also considered, including availability and...
-
MEASUREMENT OF TEMPERATURE-DEPENDENT VISCOSITY AND THERMAL CONDUCTIVITY OF ALUMINA AND TITANIA THERMAL OIL NANOFLUIDS
PublicationIn this study results of simultaneous measurements of dynamic viscosity, thermal conductivity, electrical conductivity and pH of two nanofluids, i.e. thermal oil/Al2O3 and thermal oil/TiO2 are presented. Thermal oil is selected as a base liquid because of possible application in ORC systems as an intermediate heating agent. Nanoparticles were tested at the concentration of 0.1%, 1% and 5% by weight within temperature range from...
-
Interfacial adhesion evaluation in (low-density polyethylene)/elastomer blends
PublicationLow-density polyethylene (LDPE) with different elastomers at a ratio of 50/50 wt% blends was prepared by using a co-rotating twin-screw extruder. Three kinds of elastomers were used: ground tire rubber (GTR), partially crosslinked butyl rubber (KalarVR ), and styrenebutadiene- rubber block copolymer (SBS; KratonVR ). For better characterization of interaction between polyethylene and elastomer, influence of the type of elastomer on...
-
On low-fidelity models for variable-fidelity simulation-driven design optimization of compact wideband antennas
PublicationThe paper addresses simulation-driven design optimization of compact antennas involving variable-fidelity electromagnetic (EM) simulation models. Comprehensive investigations are carried out concerning selection of the coarse model discretization density. The effects of the low-fidelity model setup on the reliability and computational complexity of the optimization process are determined using a benchmark set of three ultra-wideband...
-
Low-Cost Flight Simulator with Possibility of Modeling of Flight Controls Failures
PublicationThe goal of this paper is to present a development of a low cost flight simulator, that allows to simulate flight controls failures. Cessna 172 has been chosen as an example of a general aviation aircraft and the flight model has been implemented in Simulink. The model allows for easy integration of an experimental autopilot, using various strategies. Aerodynamic coefficients have been calculated using software called DATCOM. Such...
-
Ladder-Based Synthesis and Design of Low-Frequency Buffer-Based CMOS Filters
PublicationBuffer-based CMOS filters are maximally simplified circuits containing as few transistors as possible. Their applications, among others, include nano to micro watt biomedical sensors that process physiological signals of frequencies from 0.01 Hz to about 3 kHz. The order of a buffer-based filter is not greater than two. Hence, to obtain higher-order filters, a cascade of second-order filters is constructed. In this paper, a more...
-
Low-Voltage LDO Regulator Based on Native MOS Transistor with Improved PSR and Fast Response
PublicationIn this paper, a low-voltage low-dropout analog regulator (ALDO) based on a native n-channel MOS transistor is proposed. Application of the native transistor with the threshold voltage close to zero allows elimination of the charge pump in low-voltage regulators using the pass element in a common drain configuration. Such a native pass transistor configuration allows simplification of regulator design and improved performance,...
-
Exhaust gas temperature measurements in diagnostic examination of naval gas turbine engines. Part I: Steady-state processes
PublicationThe article presents a possible method of detecting failures in the flow section and supply system of a naval gas turbine engine based on the exhaust gas temperature measured behind the gas generator. This temperature is a basic diagnostic parameter use for evaluating the technical state of the turbine engine in operation, and is monitored during engine start-ups, accelerations and decelerations of rotor units, and steady-load...
-
Marine propeller shaft bearings under low-speed conditions: water vs. oil lubrication
PublicationThe bearings used in shipbuilding, hydropower, and water pumps have undergone a metamorphosis in recent decades. Because of environmental regulations, lubrication with grease or mineral oil is prohibited. Thus, the standard solutions include water-lubricated bearings with polymer bushings or sealed systems lubricated with oil. When properly designed, assembled, and operated, bearings can operate reliably for years. However, specific...
-
Temperature evolution of the luminescence decay of Sr0.33Ba0.67Nb2O6: Pr3+
Publication -
Advanced Electromagnetic Metamaterials for Temperature Sensing Applications
Publication -
Temperature measurements in monitoring of large thrust bearings
PublicationW pracy przedstwiono krytyczną analizę aktualnych metod diagnostyki dużych hydrodnamicznych łożysk wzdłużnych hydrozespołów elektrowni wodnych. Wykazano niedostatki i zagrożenia płynące ze stosowania diagnostyki opartej na jednopunktowym pomiarze temperatury. Zaprezentowano wstępna koncepcję nowej metody diagnostycznej opartej na odwrotnym zagadnieniu przepływu ciepła (IPHC).
-
Room-Temperature Ferromagnetism in InSb-Mn Nanowires
Publication -
Temperature distribution in laser-clad multi-layers
Publication -
Temperature Measurements in Monitoring of Large Thrust Bearings
PublicationW pracy przedstawiono krytyczną ocenę popularnego systemu diagnostyki dużych łożysk wzdłużnych (np. łożysk nośnych hydrogeneratorów), w którym stosowany jest jednopunktowy pomiar temperatury w klockach łożyskowych. Stwierdzono, że taki układ pomiarowy nie pozwala na bezpieczną eksploatację łożysk, ponieważ posiada bardzo duże opóźnienie czasowe, nie daje informacji o lokalnych zagrożeniach, nie pozwala racjonalnie ustalić poziomów...
-
Temperature measurements in monitoring of large thrust bearings
PublicationW pracy przedstwiono krytyczną analizę aktualnych metod diagnostyki dużych hydrodnamicznych łożysk wzdłużnych hydrozespołów elektrowni wodnych. Wykazano niedostatki i zagrożenia płynące ze stosowania diagnostyki opartej na jednopunktowym pomiarze temperatury. Zaprezentowano wstępna koncepcję nowej metody diagnostycznej opartej na odwrotnym zagadnieniu przepływu ciepła.
-
Temperature distribution in laser-clad multi-layers
PublicationW pracy przedstawiono porownanie rezultatów numerycznej symulacji rozkładu temperatur w warstwach nakładanych laserowo z wynikami pomiarów doświadczalnych. Otrzymano bardzo dobrą zgodność wyników co pozwala wnioskować, że przedstawiony model numeryczny może służyć jako efektywne narzędzie wstępnego doboru parametrów procesu laserowego nakładania warstw.
-
Creep failure prediction of pipelines in elevated temperature
PublicationW pracy omówiono zastoswanie modelu konstytutytwnego pełzania pozwalającego na analizę trwałości metalowych ruruciągów pracujących w wysokich temperaturach. Zaprezentowano wyniki obliczeń opartych na metodzie elementów skończonych (MES) wykonanych z wykorzystaniem procedur użytkownika w komercyjnym programie MES. Porównano wyniki dla dwóch typów 4-węzłowych elementów powłokowych.
-
Universal velocity and temperature profiles in bubbly flows.
PublicationW pracy przedstawiono model przepływu pęcherzykowego oparty na sumowaniu energii dysypacji pochodzącej od przepływu ścinającego bez pęcherzyków oraz dysypacji pochodzącej od obecności pęcherzyków. Rozwiązania równań różniczkowych opisujących model dają w wyniku uniwersalne profile prędkości i temperatur, które są bardzo przydatne w praktyce inżynierskiej.
-
Parameters’ Identification of Perzyna and Chaboche Viscoplastic Models for Aluminum Alloy at Temperature of 120◦C
PublicationThe main purpose of this paper is the parameters identification of the Perzyna and the Chaboche models for the aluminum alloy at elevated temperature. The additional purpose is comparison of the results for these viscoplastic models. The results have been verified by the numerical simulation of the laboratory tests. The material parameters have been calculated on the basis of the uniaxial tension test. The determination of the...
-
Exhaust gas temperature measurements in diagnostic examination of naval gas turbine engines. Part II. Unsteady processes
PublicationThe second part of the article presents the results of operating diagnostic tests of a two- and three-shaft engine with a separate power turbine during the start-up and acceleration of the rotor units. Attention was paid to key importance of the correctness of operation of the automatic engine load control system, the input for which, among other signals, is the rate of increase of the exhaust gas flow temperature. The article...
-
Voltage variations and their reduction in a rural low-voltage network with PV sources of energy
PublicationRenewable sources of energy (RES), especially photovoltaic (PV) micro-sources, are very popular in many countries. This way of clean power production is applied on a wide scale in Poland as well. The Polish legal regulations and tariffs specify that every prosumer in a low-voltage network may feed this network with a power not higher than the maximum declared consumed power. In power networks with RES, the voltage level changes...