Search
Search results for: a posteriori error estimator
-
Accurate Computation of IGBT Junction Temperature in PLECS
PublicationIn the article, a new method to improve the accuracy of the insulated-gate bipolar transistor (IGBT) junction temperature computations in the piecewise linear electrical circuit simulation (PLECS) software is proposed and described in detail. This method allows computing the IGBT junction temperature using a nonlinear compact thermal model of this device in PLECS. In the method, a nonlinear compact thermal model of the IGBT is...
-
Measurement method for capacitive sensors for microcontrollers based on a phase shifter
PublicationA complete measurement method dedicated to capacitive sensors has been developed. It includes the development of hardware (an analogue interface circuit for microcontrollers with built-in times/counters and analogue comparators) and software (a measurement procedure and a systematic error calibration (correction) algorithm which is based on a calibration dictionary). The interface circuit consists of a low-pass filter and a phase...
-
Design of synchronous generator two inputs regulator based on hinf control theory.
PublicationThe power system is highly nonlinear system, its dynamics depends on system network configuration, system loading… etc. To overcome the above mentioned difficulties and fulfill the performance requirements the different control methods are considered and tested for design of synchronous generator control system. Application of the H optimization method to synchronous generator regulator based on measurement of generator voltage...
-
Integration Data Model of the Bathymetric Monitoring System for Shallow Waterbodies Using UAV and USV Platforms
PublicationChanges in the seafloor relief are particularly noticeable in shallow waterbodies (at depths up to several metres), where they are of significance for human safety and environmental protection, as well as for which the highest measurement accuracy is required. The aim of this publication is to present the integration data model of the bathymetric monitoring system for shallow waterbodies using Unmanned Aerial Vehicles (UAV) and...
-
Underwater Acoustic Communications in Time-Varying Dispersive Channels
PublicationUnderwater acoustic communication (UAC) system designers tend to transmit as much information as possible, per unit of time, at as low as possible error rate. However, the bit rate achieved in UAC systems is much lower than for wire or radio-communication systems. This is due to disadvantageous properties of the UAC channels, namely the sea and inland waters. Estimation of UAC channel transmission properties is possible within...
-
Analogue GPS repeater
PublicationThis article concerns the problem of difficulty in correct indoor Global Positioning System (GPS) signals reception due to attenuation. Radio signal repeaters are proposed as means to solve this problem. Firstly, the GPS signal characteristics are described, emphasizing their low power in the point of reception. In the second part, various applications of GPS signal repeater, where indoor GPS signals reception is required, are...
-
Ocena dokładności określania osi toru kolejowego na drodze pomiarów satelitarnych
PublicationW 2009 roku na Politechnice Gdańskiej rozpoczęto badania nad wykorzystaniem serwisu pomiarów fazowych NAVGEO aktywnej sieci geodezyjnej ASG-EUPOS dla przeprowadzania ciągłych pomiarów przebiegu trasu kolejowej. Celem kontynuowanych badań jest próba oceny możliwości zastosowania pomiarów fazowych GNSS, realizowanych przez kilka odbiorników, dla projektowania oraz inwentaryzacji toru kolejowego. Do oceny dokładności określenia osi...
-
Product Graph Invariants with Applications in the Theory of Information
PublicationThere are a large number of graph invariants. In the paper, we consider some of them, e.g. the independence and chromatic numbers. It is well know that we cannot efficiently calculate these numbers for arbitrary graphs. In the paper we present relations between these invariants and concepts from the theory of information. Concepts such as source coding and transmission over a noisy channel with zero probability of error are modeled...
-
The accuracy assessment of determining the axis of railway track basing on the satellite surveying
PublicationW 2009 roku na Politechnice Gdańskiej rozpoczęto badania nad wykorzystaniem serwisu pomiarów fazowych NAVGEO aktywnej sieci geodezyjnej ASG-EUPOS dla przeprowadzania ciągłych pomiarów przebiegu trasu kolejowej. Celem kontynuowanych badań jest próba oceny możliwości zastosowania pomiarów fazowych GNSS, realizowanych przez kilka odbiorników, dla projektowania oraz inwentaryzacji toru kolejowego. Do oceny dokładności określenia osi...
-
Computing methods for fast and precise body surface area estimation of selected body parts
PublicationCurrently used body surface area (BSA) formulas give satisfactory results only for individuals with typical physique, while for elderly, obese or anorectic people accurate results cannot be expected. Particularly noteworthy are the results for individuals with severe obesity (body-mass index greater than 35 kg/m2), for which BSA estimation errors reached 80%. The main goal of our study is the development of precise BSA models for...
-
An Empirical System Loss Model for Body Area Networks in a Passenger Ferry Environment
PublicationThis paper presents a general empirical system loss model for estimating propagation loss in Body Area Networks in off-body communications at 2.45 GHz in a passenger ferry environment. The model is based on measurements, which were carried out in dynamic scenarios in the discotheque passenger ferry environment. The model consists of three components: mean system loss, attenuation resulting from the variable antenna position on...
-
An Empirical System Loss Model for Body Area Networks in a Passenger Ferry Environment
PublicationThis paper presents a general empirical system loss model for estimating propagation loss in Body Area Networks in off-body communications at 2.45 GHz in a passenger ferry environment. The model is based on measurements, which were carried out in dynamic scenarios in the discotheque passenger ferry environment. The model consists of three components: mean system loss, attenuation resulting from the variable antenna position on...
-
Identification of nonstationary multivariate autoregressive processes– Comparison of competitive and collaborative strategies for joint selection of estimation bandwidth and model order
PublicationThe problem of identification of multivariate autoregressive processes (systems or signals) with unknown and possibly time-varying model order and time-varying rate of parameter variation is considered and solved using parallel estimation approach. Under this approach, several local estimation algorithms, with different order and bandwidth settings, are run simultaneously and compared based on their predictive performance. First,...
-
A MODEL FOR FORECASTING PM10 LEVELS WITH THE USE OF ARTIFICIAL NEURAL NETWORKS
PublicationThis work presents a method of forecasting the level of PM10 with the use of artificial neural networks. Current level of particulate matter and meteorological data was taken into account in the construction of the model (checked the correlation of each variable and the future level of PM10), and unidirectional networks were used to implement it due to their ease of learning. Then, the configuration of the network (built on the...
-
Modeling the effect of external load variations on single, serie and parallel connected microbial fuel cells
PublicationThis paper presents a microbial fuel cell (MFC) model designed to analyze the effect of the external load on MFC performance. The model takes into account the voltage and the chemical oxygen demand (COD) dependence on the external load. The value of the model parameters were calibrated by means of the voltage relaxation method tests using a controlled load current. Laboratory measurements and MATLAB Simulink model computations...
-
A hierarchical observer for a non-linear uncertain CSTR model of biochemical processes
PublicationThe problem of estimation of unmeasured state variables and unknown reaction kinetic functions for selected biochemical processes modelled as a continuous stirred tank reactor is addressed in this paper. In particular, a new hierarchical (sequential) state observer is derived to generate stable and robust estimates of the state variables and kinetic functions. The developed hierarchical observer uses an adjusted asymptotic observer...
-
Resistant to correlated noise and outliers discrete identification of continuous non-linear non-stationary dynamic objects
PublicationIn this study, dedicated methods of parameter estimation were used to identify the coefficients of continuous models represented by linear and nonlinear differential equations. The necessary discrete-time approximation of the base model is achieved by appropriately tuned FIR linear integral filters. The resulting discrete descriptions, which retain the original continuous parameterization, can then be identified using the classical...
-
Analytical Expression for the Time-Domain Discrete Green's Function of a Plane Wave Propagating in the 2-D FDTD Grid
PublicationIn this letter, a new closed-form expression for the time-domain discrete Green's function (DGF) of a plane wave propagating in the 2-D finite-difference time-domain (FDTD) grid is derived. For the sake of its verification, the time-domain implementation of the analytic field propagator (AFP) technique was developed for the plane wave injection in 2-D total-field/scattered-field (TFSF) FDTD simulations. Such an implementation of...
-
Analytical Expression for the Time-Domain Green's Function of a Discrete Plane Wave Propagating in the 3-D FDTD Grid
PublicationIn this paper, a closed-form expression for the time-domain dyadic Green’s function of a discrete plane wave (DPW) propagating in a 3-D finite-difference time-domain (FDTD) grid is derived. In order to verify our findings, the time-domain implementation of the DPW-injection technique is developed with the use of the derived expression for 3-D total-field/scattered-field (TFSF) FDTD simulations. This implementation requires computations...
-
The performance of ETFs on developed and emerging markets with consideration of regional diversity
PublicationThis study evaluates the performance of Exchange-Traded Funds (ETFs) by using various tracking error calculation approaches. The aim of the paper is, on the one hand, an evaluation of the performance of ETFs relative to their benchmarking indexes and, on the other, an endeavour to specify any relationship between this performance and both geographical location and the degree of market development. The research was conducted on...
-
A Bayesian regularization-backpropagation neural network model for peeling computations
PublicationA Bayesian regularization-backpropagation neural network (BRBPNN) model is employed to predict some aspects of the gecko spatula peeling, viz. the variation of the maximum normal and tangential pull-off forces and the resultant force angle at detachment with the peeling angle. K-fold cross validation is used to improve the effectiveness of the model. The input data is taken from finite element (FE) peeling results. The neural network...
-
Resistant to correlated noise and outliers discrete identification of continuous non-linear non-stationary dynamic objects
PublicationIn this article, specific methods of parameter estimation were used to identify the coefficients of continuous models represented by linear and nonlinear differential equations. The necessary discrete-time approximation of the base model is achieved by appropriately tuned FIR linear integral filters. The resulting discrete descriptions, which retain the original continuous parameterization, can then be identified using the classical...
-
MEMORY EFFECT ANALYSIS USING PIECEWISE CUBIC B-SPLINE OF TIME FRACTIONAL DIFFUSION EQUATION
PublicationThe purpose of this work is to study the memory effect analysis of Caputo–Fabrizio time fractional diffusion equation by means of cubic B-spline functions. The Caputo–Fabrizio interpretation of fractional derivative involves a non-singular kernel that permits to describe some class of material heterogeneities and the effect of memory more effectively. The proposed numerical technique relies on finite difference approach and cubic...
-
An optimal form of the finite element mass matrix in the analysis of longitudinal vibrations of rods
PublicationIn this paper, an attempt is made to find the optimal form of the mass matrix of a rod finite element, which allows one to obtain the smallest errors in the longitudinal frequency determination of natural vibrations of any boundary conditions within the whole range of determined frequencies. It is assumed that the mass matrix can be treated as a linear combination of the consistent and diagonal matrices. Based on analytical considerations,...
-
Novel Interpolation Method of Multi-DFT-Bins for Frequency Estimation of Signal with Parameter Step Change
PublicationThe IpDFT(Interpolation Discrete Fourier Trans-form) method is one of the most commonly used non-parametric methods. However, when a parameter (frequency, amplitude or phase) step changes in the DFT period, the DFT coefficients will be distorted seriously, resulting in the large estimation error of the IpDFT method. Hence, it is a key challenge to find an IpDFT method, which not only can eliminate the effect of the step-changed...
-
A Time Delay Controller Included Terminal Sliding Mode and Fuzzy Gain Tuning for Underwater Vehicle-Manipulator Systems
PublicationAn improved Time Delay Control (TDC) method for an Underwater Vehicle-Manipulator System (UVMS) is proposed. The proposed controller consists of three terms: a time-delay-estimation term that cancels nonlinearities of the UVMS dynamics, a Terminal Sliding Mode (TSM) term that provides a fast response and a PID term that reduces the tracking error. In addition the proposed controller uses fuzzy rules to adaptively tune the gains...
-
System Loss Model for Body Area Networks in Room Scenarios
PublicationThis paper presents an analysis of system loss in Body Area Networks for room scenarios, based on a wideband measurement campaign at 5.8 GHz. The measurements were performed with a fixed antenna transmitting vertically and horizontally polarised signals, while the user wears dualpolarised antennas. The average system losses in co- and crosspolarised channels are 41.4 and 42.6 dB for vertically polarised transmitted signals and...
-
Bridge Ergonomic Design: A Review
PublicationHuman error remains the most common cause of marine incidents and it is worth emphasizing that navigator’s performance is directly affected by ergonomic factors on the bridge. Studies regarding influence of bridge design and work environment on the operator are rare, thus the main purpose of this paper is to fill in this gap. Documents issued by recognized organizations, research publications and additional sources were reviewed...
-
Accuracy assessment of mobile satellite measurements in relation to the geometrical layout of rail tracks
PublicationThe paper presents the campaigns of mobile satellite measurements, carried out in 2009–2015 on the railway and tram lines. The accuracy of the measurement method has been analysed on the basis of the results obtained in both horizontal and vertical planes. The track axis deviation from the defined geometric shape has been analysed in the areas clearly defined in terms of geometry, i.e. on the straight sections and sections with...
-
Frequency Response Functions for Sandvik CoroBore 825 XL boring tool, 733 mm
Open Research DataFrequency Response Functions (FRF) obtained for Sandvik CoroBore® 825 XL mounted at WHN 13-15 TOS VARNSDORF CNC machine at the minimum extension of the spindle adaptor. Tool set to bore a hole with a diameter 733mm
-
Destruction of AFM probes during normal operation
Open Research DataThe quality of the images obtained with the use of an atomic force microscope is determined by the state of the blade interacting with the tested material. Image artifacts can be generated by various reasons, such as oxidation, contamination or an error in blade fabrication, but also appear as a result of the repeated scanning process and inevitable...
-
Broken rotor bar impact on sensorless control of induction machine
PublicationThe aim of the research is analysis of the sensorless control system of induction machine with broken rotor for diagnostic purposes. Increasing popularity of sensorless controlled variable speed drives requires research in area of reliability, range of stable operation, fault symptoms and application of diagnosis methods. T transformation (Cunha et al.,2003) used for conversion of instantaneous rotor currents electrical circuit...
-
At the Limits of Criticality-Based Quantum Metrology: Apparent Super-Heisenberg Scaling Revisited
PublicationWe address the question of whether the super-Heisenberg scaling for quantum estimation is indeed realizable. We unify the results of two approaches. In the first one, the original system is compared with its copy rotated by the parameter-dependent dynamics. If the parameter is coupled to the one-body part of the Hamiltonian, the precision of its estimation is known to scale at most as N−1 (Heisenberg scaling) in terms of the number...
-
Uncertainty Quantification of Additive Manufacturing Post-Fabrication Tuning of Resonator-Based Microwave Sensors
PublicationReconfigurability, especially in terms of the ability of adjusting the operating frequency, has become an important prerequisite in the design of modern microwave components and systems. It is also pertinent to microwave sensors developed for a variety of applications such as characterization of material properties of solids or liquids. This paper discusses uncertainty quantification of additive-manufacturing-based post-fabrication...
-
EVALUATION OF THE SEMIVARIOGRAM SELECTION ON THE KRIGING INTERPOLATION
PublicationThe aim of the paper is to present the possibilities of geostatistical interpolation kriging method using in the process of generating digital terrain models (DTM). The source of data is a direct measurements realized with a precision GNSS positioning kinematic measurement technique RTN. Kriging algorithm was analysed, especially in the meaning of a semivariogram every step. Theoretical semivariogram selection influence on the...
-
Effect of waviness and roughness components on transverse profiles of turned surfaces
PublicationThis paper presents the authors method of simultaneous analysis of roughness and waviness irregularity components, with the aim of better defining the key qualities and characteristics.Periodical surface machining traces may be analyzed spectrally, with the irregularity's peaks and troughs being used to define the wave's amplitude.In this work the standard composition for filtering waviness and roughness components of a surface...
-
Angle Tracking Observer for Filtering Rotor Position Estimates in Sensorless Electric Drives
PublicationSensorless electric drives use measurements of electrical quantities to estimate rotor position and speed. Measurement errors deteriorate the estimation accuracy, thus additional means are necessary to remove high-frequency components from estimated signals. This paper proposes to use an Angle Tracking Observer (ATO) for reducing noise in rotor position estimates, which is related to random errors in the measurements. A simplified,...
-
3D Monitoring - Identification of measurement problems at larger movements of the tracked points
PublicationAuthors identified the problems associated with the determination of the controlled points coordinates by use of automated Total Station placed behind transparent barrier. Important thing in the mentioned analysis was a large change of controlled points position and not stable Total Station’s stand (because of stand’s thermal drift). This two elements, combined with measurement made through glass plate determine the need for impact...
-
Realistic noise-tolerant randomness amplification using finite number of devices
PublicationRandomness is a fundamental concept, with implications from security of modern data systems, to fundamental laws of nature and even the philosophy of science. Randomness is called certified if it describes events that cannot be pre-determined by an external adversary. It is known that weak certified randomness can be amplified to nearly ideal randomness using quantum-mechanical systems. However, so far, it was unclear whether randomness amplification...
-
Application of Maximum Lenght Sequence in Silent Sonar
PublicationSilent sonars are designed to reduce the distance over which their sounding pulses can be detected by intercept sonars. In order to meet this objective, we can use periodical sounding signals that have low power, a very long duration and wide spectrum. If used in the silent sonar's receiver, matched filtration ensures very good detection of motionless or slow moving targets. However, it is more difficult to detect echo signals...
-
Evaluating Asymmetric N-Grams as Spell-Checking Mechanism
PublicationTypical approaches to string comparing marks two strings as either different or equal without taking into account any similarity measures. Being able to judge similarity is however required for spelling error corrections, as we want to find the best match for a given word. In this paper we present a bi2quadro-grams method for spelling errors correction. The method proposed uses different n-grams dimension for the source (checked)...
-
Impact of Shifting Time-Window Post-Processing on the Quality of Face Detection Algorithms
PublicationWe consider binary classification algorithms, which operate on single frames from video sequences. Such a class of algorithms is named OFA (One Frame Analyzed). Two such algorithms for facial detection are compared in terms of their susceptibility to the FSA (Frame Sequence Analysis) method. It introduces a shifting time-window improvement, which includes the temporal context of frames in a post-processing step that improves the...
-
A Spatio-temporal Approach to Intersectoral Labour and Wage Mobility
PublicationThe article presents the spatio-temporal approach for intersectoral labor and wage mobility. Analyses of interindustry mobility were performed with the use of general entropy mobility indices (GEMM). Spatio-temporal approach was obtained thanks to the separate measurement of spatial autocorrelation and regression for each set of sectoral wage and employment structure and was conducted in each year of the research period separately....
-
Dynamical description of quantum computing: generic nonlocality of quantumnoise
PublicationWe develop a dynamical non-Markovian description of quantum computing in the weak-coupling limit, in the lowest-order approximation. We show that the long-range memory of the quantum reservoir (such as the 1/t4 one exhibited by electromagnetic vacuum) produces a strong interrelation between the structure of noise and the quantum algorithm, implying nonlocal attacks of noise. This shows that the implicit assumption of quantum error...
-
Advancing Solar Energy: Machine Learning Approaches for Predicting Photovoltaic Power Output
PublicationThis research is primarily concentrated on predicting the output of photovoitaic power, an essential field in the study of renewable energy. The paper comprehensively reviews various forecasting methodologies, transitioning from conventional physical and statistical methods to advanced machine learning (ML) techniques. A significant shift has been observed from traditional point forecasting to machine learning-based forecasting...
-
Analiza niezawodności człowieka-operatora w kontekście bezpieczeństwa funkcjonalnego.
PublicationArtykuł przedstawia niektóre kwestie analizy warstwowego systemu zabezpieczeń instalacji podwyższonego ryzyka z uwzględnieniem analizy niezawodności człowieka HRA (human reliability analysis). Działania człowieka operatora w odniesieniu do systemu operatorskiego HSI (human system interface), w tym systemu alarmowego i potencjalnych błędów człowieka mogą mieć istotny wpływ na wyniki analiz probabilistycznych w procesie weryfikacji...
-
A spatio-temporal approach to intersectoral labour and wage mobility
PublicationThe article presents the spatio-temporal approach for intersectoral labor and wage mobility. Analyses of interindustry mobility were performed with the use of general entropy mobility indices (GEMM). Spatio- temporal approach was obtained thanks to the separate measurement of spatial autocorrelation and regression for each set of sectoral wage and employment structure and was conducted in each year of the research period separately....
-
On joint order and bandwidth selection for identification of nonstationary autoregressive processes
PublicationWhen identifying a nonstationary autoregressive process, e.g. for the purpose of signal prediction or parametric spectrum estimation, two important decisions must be taken. First, one should choose the appropriate order of the autoregressive model, i.e., the number of autoregressive coefficients that will be estimated. Second, if identification is carried out using the local estimation technique, such as the localized version of...
-
Determination of Odour Interactions of Three-Component Gas Mixtures Using an Electronic Nose
PublicationThe paper presents an application of an electronic nose prototype comprised of six TGS-type sensors and one PID-type sensor to identify odour interaction phenomena in odorous three-component mixtures. The investigation encompassed eight odorous mixtures—toluene-acetone-triethylamine and formaldehyde-butyric acid-pinene — characterized by different odour intensity and hedonic tone. A principal component regression (PCR) calibration...
-
A robust sliding mode observer for non-linear uncertain biochemical systems
PublicationA problem of state estimation for a certain class of non-linear uncertain systems has been addressed in this paper. In particular, a sliding mode observer has been derived to produce robust and stable estimates of the state variables. The stability and robustness of the proposed sliding mode observer have been investigated under parametric and unstructured uncertainty in the system dynamics. In order to ensure an unambiguous non-linear...