Filters
total: 472
Search results for: FE ANALYSIS
-
TEM data of (Cr,Fe,Mn,Co,Ni)3O4 High-entropy spinel oxide thin films deposited on amorphous SiO2 substrate by spray pyrolysis techniqe
Open Research DataThis Dataset include presentation of summarized TEM investigation of (Mn,Co,Fe,Ni,Cr)3O4 high-entropy spinel oxide prepared in the form of a ~ 500 nm thin film utilising a facile spray pyrolysis technique. The structural and electrical properties of the layers were characterised after exposure to temperatures in the range of 400–900 ◦C. The as-deposited...
-
Homoleptic mono-, di-, and tetra-iron complexes featuring phosphido ligands: a synthetic, structural, and spectroscopic study
PublicationWe report the first series of homoleptic phosphido iron complexes synthesized by treating either the β-diketiminato complex [(Dippnacnac)FeCl2Li(dme)2] (Dippnacnac = HC[(CMe)N(C6H3-2,6-iPr2)]2) or [FeBr2(thf )2] with an excess of phosphides R2PLi (R = tBu, tBuPh, Cy, iPr). Reaction outcomes depend strongly on the bulkiness of the phosphido ligands. The use of tBu2PLi precursor led to an anionic diiron complex 1 encompassing a planar...
-
Development and validation of lumbar spine finite element model
PublicationThe functional biomechanics of the lumbar spine have been better understood by finite element method (FEM) simulations. However, there are still areas where the behavior of soft tissues can be better modeled or described in a different way. The purpose of this research is to develop and validate a lumbar spine section intended for biomechanical research. A FE model of the 50th percentile adult male (AM) Total Human Model for Safety...
-
Warstwy tlenkowe TiO2 oraz MoO3 jako fotoanody aktywne w świetle widzialnym
PublicationNiniejsza rozprawa doktorska poświęcona jest opracowaniu metod otrzymywania i charakterystyki warstw elektrodowych dwóch półprzewodników tlenkowych a) TiO2 i b) MoO3, jako potencjalnych fotoanod aktywnych w świetle widzialnym. Zakres pracy doktorskiej obejmuje: a) opracowanie metody wytwarzania nanorurek ditlenku tytanu (TiO2NT) oraz ich modyfikację prowadzącą do zwiększenia fotoaktywności i pojemności elektrycznej, a także charakterystykę...
-
Surface activation by cyclic polarization in 1M HCl and its effects on the electrochemical response of CB-PLA 3D printed electrodes
Open Research DataThe dataset contains the electrochemical studies performed for surface activation of the CB-PLA 3D printed electrodes by electrolysis in 1M HCl solution. The studies were performed after treatment at different polarization ranges, as labeled in subfolder names. For each electrode the consecutive studies describe different samples, as labeled in subfolders:...
-
Elemental composition of deposited sediments at the tram-route junction
Open Research DataThis data set contains the elemental composition results of deposited sediments collected at the tram-route junction in Gdańsk. Sample collection began in July 2022, when the tram lines were completed and before the rails were scrubbed (27/07/2022). The second sample round was carried out following rail scrubbing in October 2022 (7/10/2022). Since February...
-
Tensile test of part of CuNiFeR pipeline
Open Research DataCopper and nickel alloys called cunifers (Cu, Ni, Fe and R – rest of alloy elements) have found wide application in the production of ship pipeline components in contact with sea water, such as, for example, the main engine cooling system. These alloys are characterized by a very high corrosion resistance, which is ensured by appropriately carried out...
-
Total electrical conductivity data of (Cr,Fe,Mn,Co,Ni)3O4 High-entropy spinel oxide thin films deposited on amorphous SiO2 substrate by spray pyrolysis techniqe
Open Research DataThis dataset includes electrical conductivity measurements results measured by van der pauw technique up to 900oC.
-
Effect of microstructure on mechanical properties of BA1055 bronze castings
PublicationThe article presents research results performed on aluminum bronze CuAl10Fe5Ni5 (BA1032) castings used for marine propellers. Metallographic studies were made on light microscope and a scanning electron microscope to assess quantitatively and qualitatively the alloy microstructure. It has been shown that the shape, size and distribution of the iron-rich phase precipitates in bronze microstructure significantly affect its mechanical...
-
Defected Ag/Cu-MOF as a modifier of polyethersulfone membranes for enhancing permeability, antifouling properties and heavy metal and dye pollutant removal
PublicationIn this study, a novel bimetallic metal-organic framework (MOF) i.e. Ag/Cu-MOF was synthesized using a solvothermal method and later incorporated at different concentrations (0.1–2 wt%) using a phase inversion method for modification and antifouling property improvement of polyethersulfone (PES) membranes. The resulting Ag/Cu-MOF characteristics were investigated using different techniques, such as FTIR, XRD, FE-SEM and EDX. The...
-
Frakcje fosforu w osadach dennych i ich biodostępność podczas doczyszczania ścieków w systemach ekologicznych
PublicationCelem niniejszej pracy było scharakteryzowanie rodzaju i udziału frakcji fosforu w profilu pionowym osadów dennych oraz określenie wpływu zmiany warunków środowiskowych na ich transformację w ekologicznych systemach oczyszczających (w jęz. ang. Ecological Treatment Systems - ETS). W pracy poddano analizie ścieki przepływające przez systemy ekologiczne oraz powstające w procesie oczyszczania osady denne. Badania prowadzono w dwóch...
-
The influence of phosphorus fractions in bottom sediments on phosphate removal in semi-natural systems as the 3rd stage of biological wastewater treatment
PublicationThe research was carried out in two semi-natural systems (the polishing ponds in Swarzewo and the free water surface constructed wetland in Zarnowiec) in Poland. They were built as the 3rd stage of a conventional mechanical–biological wastewater treatment plant. These systems were built to improve the quality of the effluent of treated wastewater. In the polishing ponds and FWS wetland system, suspended solids, organic matter as...
-
Pękanie opóźnione złączy spawanych
PublicationPrzedstawiono badania eksperymentalne i szacunki skłonności do pękania opóźnionego złączy spawanych elektrodami otulonymi EB146 na stali kadłubowej gat. AH36. Badania prowadzono przy użyciu metody kołkowej na zbudowanym, zautomatyzowanym stanowisku pomiarowym IMPLANT 02 dla elektrod generujących różne poziomy wodoru dyfundującego (2,88-15,5 mlH/100g Fe) w złączu spawanym z użyciem technologii stosowanej w przemyśle okrętowym. Wykazano...
-
Surface and Corrosion Properties of AA6063-T5 Aluminium Alloy in Molybdate-containing Sodium Chloride Solutions
PublicationCorrosion properties of aluminium alloy AA6063-T5 were investigated in molybdate-containing NaCl solutions. Electrochemical, microscopic, and spectroscopic experiments were utilized to examine the mechanism of corrosion inhibition by molybdates. SEM-EDX, magnetic force, and intermodulation electrostatic force microscopy data suggested that the inhibition initiation preferentially occurred over Fe-rich cathodic IMPs. Spectroscopic...
-
Buckling analyses of metal cylindrical silos containing bulk solids during filling
PublicationThe paper presents 3D results on stability of thin-walled cylindrical metal silos made of isotropic rolled and corrugated plates containing bulk solids. The behavior of bulk solids was described using a hypoplastic constitutive model. Nonlinear finite element (FE) analyses with both geometric and material nonlinearity were performed with a perfect and an imperfect silo shell wherein initial geometric imperfections were taken into...
-
Measurement data of cyclic voltammetry and electrochemical impedance measurements of carbon samples synthesized on axes and off axes
Open Research DataThe electrochemical performance of the multielectrode samples were investigated by cyclic voltammetry (CV) and electrochemical impedance spectroscopy (EIS) using a VMP-300 BioLogic galvanostat potentiostat (France) under the EC-lab software. All electrochemical investigations were carried out in a three-electrode cell system. The carbon multi-electrode,...
-
Hybrid electrodes composed of electroactive polymer and metal hexacyanoferrates in non-aqueous electrolytes
PublicationMateriały hybrydowe złożone z polimeru elektroaktywnego poli(3,4-etylenodioksytiofenu) (pEDOT) i heksacyjanożelazianów wybranych metali Mehcf (Me = Fe, Co, Ni) zostały poddane testom w elektrolitach niewodnych składających się z mieszaniny rozpuszczalników węglan etylenu (EC) : węglan propylenu (PC) w stosunku objętościowym 1:1 oraz wybranych soli: KPF6 i LiPF6. Właściwości elektrochemiczne materiałów badane były metodami woltamperometrii...
-
Preparation and photocatalytic activity of iron-modified titanium dioxide photocatalysts
PublicationTiO2 modyfikowany żelazem otrzymano dwiema metodami: metodą zol-żel oraz metodą impregnacji powierzchniowej. Fotokatalizatory kalcynowano w temperaturze 400C. Jako matrycę TiO2 zastosowano komercyjnie dostępne proszki ditlenku tytanu: P25 (Evonik, Niemcy, 50m2/g) oraz ST-01 (Ishihara Sangyo, Japonia, 300m2/g). Charakterystyka otrzymanych fotokatalizatorów obejmowała wyznaczenie właściwości absorpcyjnych, powierzchni właściwej BET...
-
Remediation of soils on municipal rendering plant territories using Miscanthus × giganteus
PublicationPhytoremediation, as a cost-effective, highly efficient, environmentally friendly, and green approach, gained attention to the removal of metals, including heavy metals, from contaminated soils. The toxic nature of heavy metals can have an adverse effect on human health and the ecosystem, and their removal remains a worldwide problem. Therefore, in this study, a field experiment was carried out to evaluate the potential of Miscanthus × giganteus...
-
KTaO3 a perovskite for water and air treatment
PublicationPerovskites are inorganic compounds that exhibit dielectric properties. These minerals belong to the crystal ceramics family. These compounds are described by the formula: ABX3 where, A and B are 2, 3 or 4 valuable metal ions, and X is an ion of oxygen or fluorine. An example of perovskite is the compound KTaO3. There are many methods for producing KTaO3, but the hydrothermal method is most commonly used. Perovskites can be characterized...
-
Formation enthalpies of LaLn׳O3 (Ln׳=Ho, Er, Tm and Yb) interlanthanide perovskites
PublicationHigh-temperature oxide melt solution calorimetry using 3Na2O·MoO3 at 802 °C was performed for interlanthanide perovskites LaLn׳O3 (Ln׳=Ho, Er, Tm and Yb) and lanthanide oxides (La2O3, Ho2O3, Er2O3, Tm2O3 and Yb2O3). The enthalpies of formation of these interlanthanide perovskites from binary lanthanide oxides at room temperature (25 °C) were determined to be −8.3±3.4 kJ/mol for LaHoO3, −9.9±3.0 kJ/mol for LaErO3, −10.8±2.7 kJ/mol...
-
Synthesis of reduced graphene oxide nanosheets using nanofibers from methane and biogas thermal decomposition with various catalysts
PublicationReduced graphene oxide and graphene oxide (rGO, GO) were synthesised from carbon nanofibers, which were formed in catalytic thermal decomposition of methane (CDM) and biogas with different catalysts used in the process. The aim of the work was valorization of CDM carbon nanofiber products. The samples were characterized using Raman spectra, a scanning electron microscope and a transmission electron microscope. As a result, we observe...
-
Pyrolysis of RDF and Catalytic Decomposition of the Produced Tar in a Char Bed Secondary Reactor as an Efficient Source of Syngas
PublicationOne of the technical limitations of refuse-derived fuel (RDF) pyrolysis is the high content of tar in its gas products. In order to resolve this problem, a two-stage RDF pyrolysis with a catalyst based on char from RDF pyrolysis is proposed. This paper presents the results of municipal waste pyrolysis beginning in an oven heated to 480 °C and ending with catalytic tar cracking carried out in the temperature range from 800 to 1000...
-
The Impact of Material Selection on Durability of Exhaust Valve Faces of a Ship Engine – A Case Study
Publicationwo alloys were used in order to extend the service life of marine engine exhaust valve head. Layers of cobalt base alloys were made of the powders with with chemical composition as follow: the layer marked L12; C-1,55%; Si-1,21%; Cr-29,7%; W-9%; Ni-2%; Mo<0,01%; Fe-1,7%; Co-54,83% and the layer marked N; C-1,45%; Co-38,9%; Cr-24,13%; Ni-10,43%; W-8,75%; Fe-7,64%; Mo-7,56%; Si-2,59%. Base metal was valve steel after heat treatment....
-
Modeling and Strength Calculations of Parts Made Using 3D Printing Technology and Mounted in a Custom-Made Lower Limb Exoskeleton
PublicationThis study is focused on the application of 3D-printed elements and conventional elements to create a prototype of a custom-made exoskeleton for lower limb rehabilitation. The 3D-printed elements were produced by using Fused Deposition Modeling technology and acrylonitrile butadiene styrene (ABS) material. The scope of this work involved the design and construction of an exoskeleton, experimental testing of the ABS material and...
-
Influence of anisotropic stiffness in numerical analyses of tunneling and excavation problems in stiff soils
PublicationIn the stiff overconsolidated soil deposits anisotropy influences small and intermediate strain stiffness and hence it has important impact on the results of discplacement preditcions in soil-structure modelling. The authors developed a cross-anisotropic soil model which combines both stress dependent and micro-structural anisotropy. The model is based on the anisotropic hyperelastic kernel for small strain stiffness. Reference...
-
Ultimate strength of stiffened plates subjected to compressive load and spatially distributed mechanical properties
PublicationThe present study deals with the ultimate strength of stiffened plates subjected to spatially distributed mechanical properties and compressive load. Normally, mean values of mechanical properties based on tensile tests are used to validate the numerical assessment with experimental results. However, mechanical properties may vary within a single specimen. To investigate the impact of that, random fields of yield stress and Young...
-
Deflated Preconditioned Solvers for Parametrized Local Model Order Reduction
PublicationOne of steps in the design of microwave filters is numerical tuning using full-wave simulators. Typically, it is a time-consuming process as it uses advanced computational methods, e.g. the finite-element method (FEM) and it usually requires multiple optimization steps before the specification goals are met. FEM involves solving a large sparse system of equations at many frequency points and therefore its computational cost is...
-
Two-dimensional simulations of concrete fracture at aggregate level with cohesive elements based on X-ray lCT images
PublicationThe paper presents results of two-dimensional meso-scale simulations of fracture in notched concrete beams subjected to three-point bending test. Concrete was assumed as a 4-phase material composed of aggregate grains placed in the cement matrix, interfacial transitional zones (ITZs) and macro-voids. The particle distribution was taken from real concrete beams on the basis of X-ray lCT images. Comprehensive numerical analyses were carried...
-
Ekspertyza numer 75/01/II/2016 - Określenie stanu powierzchni wewnętrznej, rury wykonanej ze stopu CuNi10Fe1,6Mn ze względu na możliwość wystąpienia produktów korozji. Określenie statusu warstwy pasywnej
PublicationElementy systemów rurociągów okrętowych mających kontakt z wodą zaburtową, takich jak np. instalacja chłodzenia silnika głównego, czy instalacja przeciw pożarowa, wykonywane są często ze stopów miedzi z nikem zwanych Cuniferami (Cu Ni Fe R-reszta pierwiastków stopowych). Cunifery charakteryzują się bardzo wysoką odpornością na korozję, pod warunkiem że procesy spawania i późniejszej pasywacji rurociągu przebiega zgodnie z właściwymi...
-
FEM and experimental investigations of concrete temperature field in the massive stemwall of the bridge abutment
PublicationThe paper deals with the prediction of early-age concrete temperature of cast-in-place stemwall of the bridge abutment. The considered object is an arch bridge located in Gda´nsk. In the case of massive structures, it is particularly important to not exceed the temperature difference between the core and the concrete surface. Too high temperature gradient generates an increase in thermal stresses, what could be the reason of exceeding...
-
Fast-SEC coupled to ICP-MS for selected metal determination and its stability over time in polish wine
PublicationMetal ions contribute to the wine browning (as reaction catalysts), turbidity (in complexes), and astringency (due to inter- action with tannins). Being aware that bioavailability and metabolism of metal ions in the human body are strictly related with their concentration and the form they occur it is important to monitor not only the total content of metals but also their speciation. Thus, we can obtain more information about...
-
Evaluation of structural and electrical properties of multicomponent spinel oxide thin films deposited via spray pyrolysis technique
PublicationThis work reports the preparation of (Mn,Co,Fe,Ni,Cr)3O4 high-entropy spinel oxide in the form of a ~ 500 nm thin film utilising a facile spray pyrolysis technique. The structural and electrical properties of the layers were characterised after exposure to temperatures in the range of 400–900 ◦C. The as-deposited layers were amorphous, and crystallised upon heat treatment at 500 ◦C. Microstructural analyses proved a homogeneous...
-
Optically transparent boron-doped nanocrystalline diamond films for spectroelectrochemical measurements on different substrates
PublicationFabrication process of optically transparent boron nanocrystalline diamond (BNCD) electrode on silicon and quartz substrate was shown. The B-NCD films were deposited on the substrates using Microwave Plasma Assisted Chemical Vapor Deposition (MWPACVD) at glass substrate temperature of 475 ºC. A homogenous, continuous and polycrystalline surface morphology with high sp3 content in B-NCD films and film thickness depending from substrate...
-
Surface sediments pollution due to shipwreck s/s “Stuttgart”: a multidisciplinary approach
PublicationShipwrecks may pose a serious source of pollution for marine ecosystems. For this reason, it is of great importance to perform a marine ecosystem risk assessment due to plausible wreck presence. One of elements of such an assessment is determining the state of the environment in the vicinity of the wreck. In the work presented, the results of studies on surface sediments samples collected around the s/s Stuttgart ship sunk during...
-
Comparison of properties of magnetoacoustic emission and mechanical Barkhausen effects for P91 steel after plastic flow and creep
PublicationW artykule przedstawiono wyniki pogłębionej analizy sygnału szumowego efektu Barkhausena dla próbek ze stali krzemowej Fe-2%Si po deformacji plastycznej. Badane były próbki po walcowaniu na zimno powodującym odkształcenie względne w zakresie do 8%. Pierwsze podejście polegało na analizie w dziedzinie czasu widma badanego sygnału. Analiza ta została uzupełniona o analizę liczby zliczeń impulsów w funkcji napięcia progowego, zarówno...
-
Simplified approach to assess the dynamic response of a container ship subjected to bow slamming load
PublicationSimplified approach to assess the dynamic response of a container ship subjected to the bow slamming load, resulting in a transient vibratory response, typically called a 'whip-ping', is presented. The accurate numerical modelling is very complex and involves cou-pling of the hydrodynamic and structural solution at every time step, leading to huge com-putational and workload cost. Thus, the one-way coupling methodology is adopted,...
-
High temperature oxidation behavior of SUS430 SOFC interconnects with Mn-Co spinel coating in air
PublicationIn this study, SUS430 alloy is evaluated for its high temperature corrosion properties as a possible material for interconnects of solid oxide fuel cells (SOFCs). Samples are coated with Mn-Co by commercial physical vapor deposition (PVD) process and oxidized in air for 1250 h at 800 °C. A dense cubic Mn-Co-Fe spinel layer is formed on the surface, showing great effect on corrosion reduction compared with the samples without coating....
-
Examination of advanced isotropic constitutive laws under complex stress states in plain and reinforced concrete specimens
PublicationThe performance of advanced isotropic constitutive laws under complex stress states in plain and reinforced concrete specimens is investigated. Three different formulations are chosen: original Mazars model, Mazars mi model and model proposed by Pereira and coworkers. The degradation of the material in all formulations is described via a single variable, but a strain/stress state is taken into account via quite sophisticated relationships....
-
Zastosowanie koagulantów żelazowych do usuwania arsenu z wód podziemnych w procesie koagulacji powierzchniowej
PublicationW pracy przedstawiono wyniki badań w skali ułamkowo technicznej nad zastosowaniem koagulantów żelazowych do usuwania arsenu z wody podziemnej. Stężenie arsenu w ujmowanej wodzie podczas badań sięgało 36 μg/l i niemal czterokrotnie przekraczało wartość dopuszczalną dla wód przeznaczonych do spożycia (<10 μg/l). Proces polegał na dozowaniu koagulantu żelazowego, napowietrzaniu wody a następnie filtracji przez dwuwarstwowe złoże...
-
Assessment of metal removal in a surface flow constructed wetland treating landfill leachate
PublicationThe study concerns heavy metal retention and transformation processes in a free water surface constructed wetland treating landfill leachate in a temperate climate. The total effectiveness of heavy metals removal in the analyzed CW was evaluated basing on heavy metals inflow and outflow concentrations. The concentrations of eight heavy metals (Fe, Mn, Zn, Pb, Ni, Cu, Cr, Cd) in landfill leachate (LL) and sediments were measured....
-
Erozja kawitacyjna materiałów konstrukcyjnych metalowych
PublicationW pracy przedstawiono charakterystykę kawitacji, metody ilościowego opisu zjawiska oraz omówiono kawitacyjne niszczenie stopów Fe, Cu, Ni, Ti i Co, tj. metalowych materiałów konstrukcyjnych najczęściej stosowanych w konstrukcjach narażonych na obciążenia kawitacyjne. Przy opisie kawitacyjnego niszczenia różnych grup stopów omówiono zagadnienia, które odgrywają istotną rolę podczas degradacji materiałów. W rozdziale poświęconym...
-
Distribution and removal efficiency of heavy metals in two constructed wetlands treating landfill leachate
PublicationThe results of heavy metals (Fe, Mn, Zn, Ni, Cu, Cr, Pb, Cd) removal and partitioning between aqueous and solid phases at two wetlands (TWs) treating municipal landfill leachates are presented. One of the TWs is a surface flow facility consisting of 10 ponds. The other TW is a newly constructed pilot-scale facility consisting of three beds with alternately vertical and horizontal sub-surface flow. The metals concentrations were...
-
Axial capacity of steel built-up battened columns
PublicationThis paper deals with the numerical investigation aimed to study the axial capacity of pin-ended steel built-up columns. Three methods of calculating forces in chords and batten, taking into account the material and geometric imperfections specified in the Eurocode 3 are considered. The aim of this study was to compare different methods allowing the calculation of the column load capacity and determine a simpler and faster method...
-
Comparison of different one-parameter damage laws and local stress-strain approaches in multiaxial fatigue life assessment of notched components
PublicationThis paper aims to compare the predictive capabilities of different one-parameter damage laws and local stress-strain approaches to assess the fatigue lifetime in notched components subjected to proportional bending-torsion loading. The tested fatigue damage parameters are defined using well-known stress-based, strain-based, SWT-based and energy-based relationships. Multiaxial cyclic plasticity at the notch-controlled process zone...
-
A constitutive law for concrete with smooth transition from continuous into discontinuous cracks’ description
PublicationPaper presents a constitutive model for concrete that combines a continuous and discontinuous crack’s description to simulate the concrete under tensile dominated loads. In a continuum regime, two different constitutive laws were used. First, a plasticity model with the Rankine failure criterion and an associated flow rule was used. Second, a constitutive law based on isotropic damage mechanics was formulated. Both model alternatives...
-
Exhaled breath gas sensing using pristine and functionalized WO3 nanowire sensors enhanced by UV-light irradiation
PublicationThe development of advanced metal-oxide-semiconductor sensing technologies for the detection of Volatile Organic Compounds (VOCs) present in exhaled breath is of great importance for non-invasive, cheap and fast medical diagnostics. Our experimental studies investigate the effects of operating temperature selection and UV-light irradiation on improving the response of WO3 nanowire sensors towards exhaled breath exposure. Herein,...
-
Determination of metal content in sewage sludge and sewage sludge ash to find opportunities to use them in the construction industry
PublicationSewage sludge management is becoming an increasing problem in developed and developing countries. Due to their physicochemical properties (mainly high content of heavy metals) a safe method of utilization is sought. Considering environmental protection, energy recycling, reduction in use of the raw materials and the possibility of immobilization hazardous substances, the use of ashes in building materials becomes a very good way...
-
In-situ and ex-situ resistance measurements of polypyrrole film using double-band electrode
PublicationMany in-situ techniques are performed in order to determine the resistance of conducting polymer film. However, the resistance measured in solution can be the combination of polymer resistance and that of other components, such as resistance of supporting electrolyte. Therefore, in this work, the influence of the solution on the resistance of polypyrrole (PPy) film has been studied. PPy film was electrchemically synthesized onto...
-
Analiza elektronomikroskopowa próbek pyłów z Gdańska i Zabrza
PublicationCelem badań była analiza morfologiczna cząstek pyłów oraz analiza składu elementarnego próbek pyłów przy pomocy mikroanalizatora rentgenowskiego EDX (Energy Dispersive X-Ray Spectroscopy). Próbki pyłów do analizy pobierano na terenie Gdańska i Zabrza. Zidentyfikowane przy pomocy TEM i SEM cząstki występujące w pobranych próbkach podzielono na trzy grupy ze względu na ich kształt: cząstki zaokrąglone, cząstki o kształcie nieregularnym,...