Search
Search results for: chemical reaction cross sections
-
Determining horizontal curvature of railway track axis in mobile satellite measurements
PublicationThe article discusses the applicability of a novel method to determine horizontal curvature of the railway track axis based on results of mobile satellite measurements. The method is based on inclination angle changes of a moving chord in the Cartesian coordinate system. In the presented case, the variant referred to as the method of two virtual chords is applied which consists in manoeuvring with only one GNSS (Global Navigation...
-
The Use of Direct Shear Test for Optimization of Interlayer Bonding Under a Poroelastic Layer
PublicationPoroelastic Road Surfaces (PERS) are characterised by porous structure with air void content of 20% or higher and stiffness almost 10 times lower than that of a standard asphalt course. Such properties enable noise reduction by up to 12 dB in comparison to SMA 11 mixture. However, the disadvantage of a poroelastic pavement is its low durability, which partially results from delamination from the lower layer. The paper aims to investigate...
-
Bitumen-Based Poroelastic Pavements: Successful Improvements and Remaining Issues
PublicationThis article presents the development process of designing and testing poroelastic pavement based on highly polymer-modified bitumen. Poroelastic wearing course was composed of mineral and rubber aggregate mixed with highly polymer-modified bitumen, in contrast to previous trials, during which polyurethane resins were mainly used as binder, which led to several serious technological problems concerning difficult production, insufficient...
-
Damage of a post-tensioned concrete bridge – Unwanted cracks of the girders
PublicationThe cracking of a post-tensioned T-beam superstructure, which was built using the incremental launching method, is analyzed in the paper. The problem is studied in detail, as specific damage was observed in the form of longitudinal cracks, especially in the mid-height zone of the girder at the interface of two assembly sections. The paper is a case study. A detailed inspection is done and non-destructive testing results of the...
-
Comparison of pavement noise properties on selected road sections using different CPX measuring systems: self-powered vehicle and special test trailer
PublicationThe recently published ISO standard intended to measure the noise properties of road surfaces in a standardized method (ISO 11819-2:2017) precisely defines measurement procedure of the influence of road surface on traffic noise. According to it, two types of test vehicles may be utilized: a self-powered vehicle fitted with one or more test tyres and a trailer towed by a separate vehicle with one or more test tyres mounted on the...
-
Acoustic lifecycle study of the double-layer porous asphalt on E4 in Huskvarna, Sweden
PublicationIn 2010 a double-layer porous asphalt concrete (DPAC) pavement was constructed on the E4 motorway through the Swedish city Huskvarna. Earlier experience in Sweden indicated that it was feasible to obtain a high initial noise reduction but due to the widespread use of studded tires in winter, clogging and ravelling created losses of around 2 dB per year, with an expected acoustical lifetime of only 3 years. However, the improved...
-
Assessing Highway Travel Time Reliability using Probe Vehicle Data
PublicationProbe vehicle data (also known as “floating car data”) can be used to analyze travel time reliability of an existing road corridor in order to determine where, when, and how often traffic congestion occurs at particular road segments. The aim of the study is to find the best reliability performance measures for assessing congestion frequency and severity based on probe data. Pilot surveys conducted on A2 motorway in Poland confirm...
-
Surface Texture after Turning for Various Workpiece Rigidities
PublicationIn the paper, we present an analysis of the surface texture of turned parts with L/D (length/diameter) ratios of 6 and 12 and various rigidity values. The studies were carried out on samples made of S355JR steel and AISI 304 stainless steel. A detailed analysis of 2D surface profiles was carried out by using a large number of parameters that allowed us to distinguish significant differences in the surface microgeometry, which confirmed...
-
Combining Computational Fluid Dynamics with a Biokinetic Model for Predicting Ammonia and Phosphate Behavior in Aeration Tanks
PublicationThe aim of this study was to use computational fluid dynamics for predicting the behavior of reactive pollutants (ammonia and phosphate) in the aerobic zone of the bioreactor located at the Wschod wastewater treatment plant in Gdansk, Poland. The one-dimensional advection-dispersion equation was combined with simple biokinetic models incorporating the Monod-type expressions as source terms for the two pollutants. The problem was...
-
Identification of Emotional States Using Phantom Miro M310 Camera
PublicationThe purpose of this paper is to present the possibilities associated with the use of remote sensing methods in identifying human emotional states, and to present the results of the research conducted by the authors in this field. The studies presented involved the use of advanced image analysis to identify areas on the human face that change their activity along with emotional expression. Most of the research carried out in laboratories...
-
Economical methods for measuring road surface roughness
PublicationTwo low-cost methods of estimating the road surface condition are presented in the paper, the first one based on the use of accelerometers and the other on the analysis of images acquired from cameras installed in a vehicle. In the first method, miniature positioning and accelerometer sensors are used for evaluation of the road surface roughness. The device designed for installation in vehicles is composed of a GPS receiver and...
-
TB11 test for short w-beam road barrier
PublicationFEM (Finite Element Method) is well-suited and widely used tool for simulating a range of phenomena: from these with simple and static behaviour, up to those complicated, highly nonlinear and involving many contacts. In present paper we use one of the advantages of FEM: parametric study could be easily performed and is more economical than series of in-situ tests. If recommended practices is carefully followed, results obtained...
-
Incorporating Iris, Fingerprint and Face Biometric for Fraud Prevention in e-Passports Using Fuzzy Vault
PublicationA unified frame work which provides a higher security level to e-passports is proposed. This framework integrates face, iris and fingerprint images. It involves three layers of security: the first layer maps a biometric image to another biometric image which is called biostego image. Three mapping schemes are proposed: the first scheme maps single biometric image to single biostego image, the second scheme maps dual biometric images...
-
THREE-DIMENSIONAL numerical investigation of MHD nanofluid convective heat transfer inside a CUBIC porous container with corrugated bottom wall
PublicationSimultaneous use of porous media and nanofluid as a heat transfer improvement method has recently captivated a great deal of attention. The heat transfer and entropy production of the Cu-water nanofluid inside a cubic container with a heated bottom wavy wall and an elliptic inner cylinder were numerically analyzed in this study. The container is partitioned into two sections: the left side is filled with permeable media and...
-
Low-Cost Automated Design of Compact Branch-Line Couplers
PublicationBranch-line couplers (BLCs) are important components of wireless communication systems. Conventional BLCs are often characterized by large footprints which make miniaturization an important prerequisite for their application in modern devices. State-of-the-art approaches to design of compact BLCs are largely based on the use of high-permittivity substrates and multi-layer topologies. Alternative methods involve replacement of transmission-line...
-
Detection of circulating tumor cells by means of machine learning using Smart-Seq2 sequencing
PublicationCirculating tumor cells (CTCs) are tumor cells that separate from the solid tumor and enter the bloodstream, which can cause metastasis. Detection and enumeration of CTCs show promising potential as a predictor for prognosis in cancer patients. Furthermore, single-cells sequencing is a technique that provides genetic information from individual cells and allows to classify them precisely and reliably. Sequencing data typically...
-
Innovative Implantable Left Ventricular Assist Device—Performance under Various Resistances and Operating Frequency Conditions
PublicationThis paper presents the operation of an innovative left ventricular assist device under various resistances and operating frequencies. The operating principle of the device is based on pulsatile blood flow, which is forced by a suction–discharge device pumping helium into a set of intra-cardiac balloons. In this way, the ejection fraction of the left ventricle is increased, and the mitral valve is additionally occluded. What is...
-
Heat Dissipation from the Power Cable in the Casing Pipe
PublicationThe current carrying capacity of a power cable determines its ability to carry a specific current and is related to the efficiency of dissipation of heat generated in the cable laid in a specific environment. The studies were conducted in order to determine how the characteristics of the medium around the cable affected its temperature, and thus the ability of the cable to transmit electricity. The experimentation in the lab and...
-
Field investigation of low-temperature cracking and stiffness moduli on selected roads with conventional and high modulus asphalt concrete
PublicationHigh Modulus Asphalt Concrete (HMAC) was introduced in Poland as a one of the solutions to the problem of rutting, type of deterioration common in the 1990s. After first encouraging trials in 2002 HMAC was widely used for heavily loaded national roads and motorways. However some concerns were raised about low-temperature cracking of HMAC. This was the main reason of the studies presented in this article were started. The article...
-
High frequency impulse ground penetrating radar application in assessment of interlayer connections
PublicationGround Penetrating Radar (GPR) technique is commonly used in the nondestructive evaluation of pavement structures. In particular, this method is used to estimate thicknesses of pavement layers as well as it can be utilized in advanced studies of pavement structures. The device presented in this paper comprise the high frequency impulse antennas that allow for investigating the interlayer zones in terms of their electromagnetic...
-
Designing of Track Axis Alignment with the Use of Satellite Measurements and Particle Swarm Optimization
PublicationDesigning of the track’s alignment is a key issue from the point of view of maintaining of proper geometries. The paper presents a design method for sections of railway line located in the horizontal arch. The method is adapted to the technique of mobile satellite measurements. The general principles of this measurement method have been described in the article. A project's solution has been presented using mathematical notation...
-
Tools for road infrastructure safety management in Poland
PublicationThe objective of road safety infrastructure management is to ensure that when roads are planned, designed, built and used road risks can be systematically identified, assessed, removed and mitigated. There are a number of approaches to road safety management. European Union Directive 2008/96/EC requires EU member states to use four basic tools of road safety infrastructure management. An overview of the methods in these countries...
-
Experimental studies on the impact of changing the pipe material on the propagation of the pressure wave during water hammer
PublicationAim of the paper is to present the results studying the water hammer phenomenon in pipes made of different materials, and to show the impact of changing the type of material of the pipe on the velocity of the pressure wave during the transient flow in the pipes. In terms of research material and methods, pipes made of galvanized steel and high-density polyethylene were tested. Measurements were made using strain gauges with a high...
-
Endometrial nitric oxide production and nitric oxide synthases in the equine endometrium: Relationship with microvascular density during the estrus cycle
PublicationNitric oxide (NO) plays an important role in angiogenesis and in the regulation of the blood flow. This study was carried out to investigate (i) the effects of endogenous estrogens and progestins and exogenous progesterone (P(4)) (5 ng/ml or 1 microg/ml) or estradiol 17beta (E(2)beta) (50 pg/ml or 1 microg/ml) on in vitro endometrial NO synthesis; (ii) the presence of different isoforms of NO synthase;...
-
A Method for Determination and Compensation of a Cant Influence in a Track Centerline Identification Using GNSS Methods and Inertial Measurement
PublicationAt present, the problem of rail routes reconstruction in a global reference system is increasingly important. This issue is called Absolute Track Geometry, and its essence is the determination of the axis of railway tracks in the form of Cartesian coordinates of a global or local coordinate system. To obtain such a representation of the track centerline, the measurement methods are developed in many countries mostly by the using...
-
THE APPLICATION EFFECTS OF CONTINUOUS SATELLITE MEASUREMENTS OF RAILWAY LINES
PublicationThe paper presents results of satel lite surveying of the railway's rout es, which have been conducted just after starting in Poland (in 2008) the Active Geodesy Network ASG-EU POS. Afterwards it was possible to effectively utilize the GNSS survey ing results for the inventory of the (exploring) railways in service. Already at the beginning of 2009, the research team from Gdansk University of Technology and Naval Academy in Gdynia,...
-
Application of adjusted subpixel method (ASM) in HRCT measurements of the bronchi in bronchial asthma patients and healthy individuals
PublicationBackground: Recently, we described a model system which included corrections of high-resolution computedtomography (HRCT) bronchial measurements based on the adjusted subpixel method (ASM).Objective: To verify the clinical application of ASM by comparing bronchial measurements obtained bymeans of the traditional eye-driven method, subpixel method alone and ASM in a group comprised ofbronchial asthma patients and healthy individuals.Methods:...
-
Potential for ITS/ICT Solutions in Urban Freight Management
PublicationThe article presents a study on applying ITS solutions in planning and management of urban freight transport in Gdynia. The traffic management system Tristar which is under implementation and its related systems show a potential to assist in development of freight transport measures. Recommendations for urban freight policy development supplementing Gdynia's Sustainable Urban Mobility Plan were used as a basis for identification...
-
Tools for road infrastructure safety management – Polish experiences
PublicationThe objective of road safety infrastructure management is to ensure that when roads are planned, designed, built and used road risks can be systematically identified, assessed, removed and mitigated. There are a number of approaches to road safety management. European Union Directive 2008/96/EC requires EU member states to use four basic tools of road safety infrastructure management. An overview of the methods in these countries...
-
Influence of windsurfing fin stiffness distribution on the lift-drag characteristics
PublicationThis article addresses the problem of determining the hydromechanical loads generated by flexible hydrofoils. The research was done on the example of the composite windsurfing fin for the RS:X monotype class. Despite the assumption of fins identity, everyday practice showed that variations of mechanical properties occur and strongly affect their performance. Therefore, we decided to study the differences between the windsurfing...
-
Review and evaluation of cold recycling with bitumen emulsion and cement for rehabilitation of old pavements
PublicationThe article presents Polish experience with cold recycling of asphalt pavements with theusage of bituminous emulsion and cement. In the 1990s numerous roads in Polandrequired immediate reinforcement due to their significant degradation. Implementation ofthe cold recycling technology was one of the solutions to this problem. Cold recycledmixtures containebeside the recycled asphalt pavement and aggregateetwo differenttypes of binding...
-
XPS analysis of strontium titanate ceramics
Open Research DataThe chemical composition of the strontium titanite doped with yttrium and iron ceramic samples was investigated. Samples of Y0.07Sr0.93Ti0.8Fe0.2 were prepared by solid phase reaction and sintered for 24 and 48 hours. Chemical composition was measured by UHV OmicronNanotechnology XPS system. The analysis confirmed the chemical composition of the ceramics...
-
Study on the Positioning Accuracy of the GNSS/INS System Supported by the RTK Receiver for Railway Measurements
PublicationCurrently, the primary method for determining the object coordinates is positioning using Global Navigation Satellite Systems (GNSS) supported by Inertial Navigation Systems (INS). The main goal of this solution is to ensure high positioning availability, particularly when access to satellite signals is limited (in tunnels, areas with densely concentrated buildings and in forest areas). The aim of this article is to determine whether...
-
Investigation of Acoustic Properties of Poroelastic Asphalt Mixtures in Laboratory and Field Conditions
PublicationMeasures for the improvement of acoustic conditions in the vicinity of roads include the construction of pavement structures with low-noise surfaces with optimal macrotexture and the highest possible sound absorption coefficient. Laboratory evaluation of acoustic properties of a designed asphalt mixture before its placement in the pavement is a good solution. Currently, the most popular method for the determination of the sound...
-
An advanced tool integrating failure and sensitivity analysis into novel modeling of the stormwater flood volume
PublicationAn innovative tool for modeling the specific flood volume was presented that can be applied to assess the need for stormwater network modernization as well as for advanced flood risk assessment. Field measurements for a catchment area in Kielce, Poland, were used to apply the model and demonstrate its usefulness. This model extends the capability of recently developed statistical and machine learning hydrodynamic models developed...
-
Experimental Investigation of the Thermal Performance of a Wickless Heat Pipe Operating with Different Fluids: Water, Ethanol, and SES36. Analysis of Influences of Instability Processes at Working Operation Parameters
PublicationIn this study, the influences of different parameters on performance of a wickless heat pipe have been presented. Experiments have been carried out for an input power range from 50 W to 300 W, constant cooling water mass flow rate of 0.01 kg/s, and constant temperature at the inlet to condenser of 10 C. Three working fluids have been tested: water, ethanol, and SES36 (1,1,1,3,3-Pentafluorobutane) with different filling ratios (0.32,...
-
Synthesis, structure and properties of poly(ether-urethane)s synthesized using a tri-functional oxypropylated glycerol as a polyol
PublicationThe main aim of this work was to obtain poly(ether-urethane)s using tri-functional polyoxyalkylene polyol (Rokopol G1000), which introducing the chemical cross-links into the structure of polyurethanes. Poly(ether-urethane)s were prepared using two-step method, called prepolymer method, which involves in the first step the reaction of 4,4'-diphenylmethane diisocyanate (MDI) and tri-functional polypropylene glycol glycerol triether...
-
Excitation of Non-Wave Modes by Sound of Arbitrary Frequency in a Chemically Reacting Gas
PublicationThe nonlinear phenomena in the field of high intensity sound propagating in a gas with a chemical reaction, are considered. A chemical reaction of A → B type is followed by dispersion and attenuation of sound which may be atypical during irreversible thermodynamic processes under some conditions. The first and second order derivatives of heat produced in the chemical reaction evaluated at the equilibrium temperature, density and...
-
Physical Chemistry_GTM_20_21_winter
e-Learning CoursesThe aim of the subject is to familarize the student with fundamental physico-chemical laws in chemical thermodynamics, phase equilibria and chemical equilibria together with ability of solving relevant text problems involving calculations, as well as teachnig him/her effective and safe carrying out simple experiments/measurements of physico-chemical quantities and proper presentation and interpretation of their results. LECTURES Chemical...
-
Agata Kot-Wasik prof. dr hab. inż.
PeopleAgata Kot-Wasik, born in 1964 in Siedlce, graduated in 1988 from the Faculty of Chemistry, Gdańsk University of Technology in Industrial and Technical Analysis. In 1988-1992 she was employed in the Department of Organic Chemistry. In 1990, she completed postgraduate studies "Instrumental techniques in the traces analysis and Environmental Protection" at GUT, and in 1992 began PhD Studies at the Faculty of Chemistry, GUT, which...
-
Kinetics of cross-linking processes of fast-curing polyurethane system
PublicationThis work focuses on the application of thermal analysis and kinetics investigations to analyze chemical processes during cross-linking of the complex fast-curing polyurethane system. Non-isothermal Differential Scanning Calorimetry (DSC) measurements were performed for both stoichiometric mixtures of polyol and isocyanate component and for mixture with large isocyanate excess. Isoconversional methods were used to calculate initial...
-
The searchlight problem for road networks
PublicationWe consider the problem of searching for a mobile intruder hiding in a road network given as the union of two or more lines, or two or more line segments, in the plane. Some of the intersections of the road network are occupied by stationary guards equipped with a number of searchlights, each of which can emit a single ray of light in any direction along the lines (or line segments) it is on. The goal is to detect the intruder,...
-
Chemical composition analysis of the LSNO ceramics
Open Research DataThe chemical composition of a series of La-Sb-Nb-O ceramics manufactured by the solid-phase reaction method was analyzed. The samples with a various antimony content were measured by XPS method (OmicronNanotechnology UHV system). Analysis confirmed presence of elements: La, Sb, Nb.
-
Experimental validation of the rolling resistance measurement method including updated draft standard
PublicationThe main objective of ROSANNE is the harmonisation and standardisation of the measurement of skid resistance, noise emission and rolling resistance of road pavements. Regarding rolling resistance characterisation, a draft for standardization of a harmonized procedure for classification of road surfaces across Europe has been prepared within WP3 (deliverable 3.5). The procedure deals with the direct measurement on real roads of...
-
Identification of damages in the inlet air duct of a diesel engine based on exhaust gas temperature measurements
PublicationThe temperature of the exhaust gas of a diesel piston engine, measured in the characteristic control sections of its thermo-flow system, can be a valuable source of diagnostic information about the technical condition of the elements limiting the working spaces thus separated, including the turbocharging system, but also its fuel supply system and replacement of the medium. In standard marine engine measurement systems equipped...
-
Non-Wave Variations in Temperature Caused by Sound in a Chemically Reacting Gas
PublicationA weakly nonlinear generation of non-acoustic modes in the field of sound in a gas is considered. An exotericchemical reaction of A->B type, which takes place in a gas, may be reversible or not. Two types of sound areconsidered, low-frequency and high-frequency as compared with the characteristic time of a chemical reaction.For both these cases, the governing equations of non-acoustic modes are derived and conclusions of the efficiencyof...
-
Maillard-reaction (glycation) of biopolymeric packaging films; principles, mechanisms, food applications
PublicationBackground The biodegradable, biocompatible, sustainable, and renewable nature of biomaterials has led to increased interest in developing biopolymeric food packaging films (BFPFs) with green ingredients and strategies. To enhance the performance of these films, biopolymer molecules can be modified or combined with additives like nanomaterials, cross-linkers, bioactive compounds, and other polymers, particularly with Maillard-reaction...
-
Kinetics study of the fully bio-based poly(propylene succinate) synthesis. Functional group approach
PublicationCurrently, the increasing importance of the bio-based chemical compounds development is visible in the polymer chemistry, chemical engineering and materials science. It is well-known that the various purity level and different contaminants characterize petrochemical-based compounds compared to their biobased counterparts. Therefore, it is necessary to find out the contaminants impact on the bio-based monomers synthesis. One of...
-
Standing Waves and Acoustic Heating (or Cooling) in Resonators Filled with Chemically Reacting Gas
PublicationStanding waves and acoustic heating in a one-dimensional resonator filled with chemically reacting gas, is the subject of investigation. The chemical reaction of A ! B type, which takes place in a gas, may be reversible or not. Governing equations for the sound and entropy mode which is generated in the field of sound are derived by use of a special mathematical method. Under some conditions, sound waves propagating in opposite...
-
Plastic Debris in the Stomach of the Invasive Signal Crayfish Pacifastacus leniusculus from a Baltic Coastal River
PublicationPollution by plastic debris, widely recognized as a growing global problem [1-3] is caused by the production of synthetic polymers. Over recent years, the production of plastics has increased, while in Europe, fossil-based plastics production has decreased, and recycled plastics production has increased [4]. There are different types of plastics. Some types of plastic ingredients, applied in a wide variety of cosmetics and personal...