Filters
total: 1432
filtered: 856
Search results for: ERASURE
-
Beeswax And Palmitic Acid Utilization With Heat Pipes For Electronics Cooling
PublicationThis paper presents an experimental study of heat pipes supported by phase change materials (PCMs) coated at their adiabatic sections in application for electronics cooling. The PCMs investigated in this research were palmitic acid and beeswax, the latter being considered as a more cost-effective alternative. The study focused on three powers: 20W, 25W, and 30W. The experimental results revealed that the incorporation of palmitic...
-
Nanoparticle Tracking Analysis of Urinary Extracellular Vesicle Proteins as a New Challenge in Laboratory Medicine
PublicationUrinary extracellular vesicle (uEV) proteins may be used as specific markers of kidney damage in various pathophysiological conditions. The nanoparticle-tracking analysis (NTA) appears to be the most useful method for the analysis of uEVs due to its ability to analyze particles below 300 nm. The NTA method has been used to measure the size and concentration of uEVs and also allows for a deeper analysis of uEVs based on their protein...
-
Actual and reference evapotranspiration for a natural, temperate zone fen wetland – Upper Biebrza case study
PublicationEvapotranspiration is the key and predominant component of the water balance in wetlands. Direct evapotranspiration measurements are challenging in wetlands due to their remoteness and high surface water level. This article describes the actual (ETa and reference evapotranspiration (ET0) from a cultivated wet meadow located in the Biebrza National Park – the largest national park in north-east Poland, Central Europe. The data were...
-
CONDITIONS OF THE GREEN TRANSFORMATION. THE CASE OF THE EUROPEAN UNION
PublicationThe main purpose of the paper is to identify the factors that determine the course of green transformation and to assess the current stage and possible directions of change in subsequent years in EU countries. The literature lacks comprehensive studies that show the impact of diverse types of factors on the course of green transformation. For this purpose, two perspectives of the research – economic and environmental – are usually...
-
Accounting for the distributions of input quantities in the procedure for the measurement uncertainty evaluation when calibrating the goniometer
PublicationThe discords concerning the measurement uncertainty evaluation in the Guide to the Expressing of Uncertainty in Measurement (GUM) and its Supplement 1 are considered. To overcome these discords, the authors of the paper propose to use the kurtosis method and the law of the propagation of the expanded uncertainty. Using the example of the goniometer calibration, the features of accounting for the distribution laws of input quantities...
-
Price convergence in the EU-an aggregate and disaggregate approach
PublicationThis article examines the price dispersion in the European Union (EU) over 15 years (1990-2005). An extensive overview of the literature offers inconclusive results with the half-lives of price shocks from 2.8 to 282 months. Until now, most of the empirical research has been either micro or macro based. In contrast, we conducted a complex analysis utilizing both aggregate and disaggregate price data. The macro approach is based...
-
Kompleksowa analiza symulacyjna układu napędowego zespołu trakcyjnego
PublicationThe paper describes an approach to comprehensive analysis of traction electric drive. The drivetrain of ED-74 electric unit equipped with four inverter-fed induction motors was modeled in Matlab/Simulink. The model consists of functional blocks as: motors, inverters, drive controllers, filters. Structure and operation of the model was described. Chosen simulation results were presented and discussed. Two methods of modeling the...
-
Knowledge Management Critical Success Factors and the Innovativeness of KIBS Companies
PublicationThe purpose of this paper is to examine the influence of two critical success factors for knowledge management (i.e. leadership and support by the management, motivational practices) on the innovativeness of knowledge-intensive business service (KIBS) companies in the SMEs sector. A sample of 400 companies (KIBS SMEs) located in the Pomeranian District in Poland was selected. The questionnaire was designed to measure knowledge...
-
Effects of Salvia officinalis and Thymus vulgaris on oxidant-induced DNA damage and antioxidant status in HepG2 cells
PublicationSalvia officinalis (SO) and Thymus vulgaris (TV) are medicinal plants well known for their curative powers. However, the molecular mechanisms responsible for these abilities of sage and thyme have not been fully understood yet. In this study we investigated the composition and the quantitative estimation of plant extracts, the protective effects of plant extracts against hydrogen peroxide- and 2,3-dimethoxy-1,4 naphthoquinone-induced...
-
Assessment of the Steering Precision of a Hydrographic Unmanned Surface Vessel (USV) along Sounding Profiles Using a Low-Cost Multi-Global Navigation Satellite System (GNSS) Receiver Supported Autopilot
Publicationhe performance of bathymetric measurements by traditional methods (using manned vessels) in ultra-shallow waters, i.e., lakes, rivers, and sea beaches with a depth of less than 1 m, is often difficult or, in many cases, impossible due to problems related to safe vessel maneuvering. For this reason, the use of shallow draft hydrographic Unmanned Surface Vessels (USV) appears to provide a promising alternative method for performing...
-
Systems of General Grants for Local Governments in Selected EU Countries Against the Background of the General Theory of Fiscal Policy
PublicationFiscal policy, including its expenditure aspect, is often discussed and analysed from a variety of angles in the literature on public finances, undoubtedly due to the major importance of this topic. However, not all areas of the expenditure part of fiscal policy have been subjected to in-depth analysis. One of the less discussed tools of fiscal policy consists of general purpose transfers, which are a certain type of expenditure...
-
Bankruptcy Law Severity for Debtors: Comparative Analysis Among Selected Countries
PublicationPurpose: The objective of this paper is to propose the new indicator of bankruptcy law severity for debtors (BLSI-Bankruptcy Law Severity Index). On the basis of this index we conducted comparative analysis of debtor/creditor friendliness of bankruptcy laws among 27 selected countries. Design/Methodology/Approach: In the research the following methods were used: analysis of legal acts, literature review and expert method. Findings:...
-
Rapid dimension scaling of compact microwave couplers with power split correction
PublicationIn this paper, a technique for rapid re-design ofcompact microwave couplers with respect to operating frequency is discussed. Our methodology involves an inverse surrogate model setup using several reference designs optimized (at the level of equivalent circuit representation of the coupler) for a set of operating frequencies within a range of interest. The surrogate establishes the relationship between the operating frequency...
-
Adapting new tools of urban freight management based on Gdynia’s dedicated delivery bays example – an analysis of the process
PublicationThe article presents an analysis of a process which ultimately helped Gdynia to designate pilot delivery sites in its downtown area using international experience. A verification was conducted of policy transfer theory and its practical implementation based on an URBACT Freight Tails project. While the choice of the solution was based on critical analysis of existing practical examples, it needed to be adapted to the local conditions...
-
Evaluation of Three Peptide Immobilization Techniques on a QCM Surface Related to Acetaldehyde Responses in the Gas Phase
PublicationThe quartz-crystal microbalance is a sensitive and universal tool for measuring concentrations of various gases in the air. Biochemical functionalization of the QCM electrode allows a label-free detection of specific molecular interactions with high sensitivity and specificity. In addition, it enables a real-time determination of its kinetic rates and affinity constants. This makes QCM a versatile bioanalytical screening tool for...
-
PLANOWANIE BEZPIECZNYCH I „ZIELONYCH” SYSTEMÓW KOMUNIKACYJNYCH
PublicationIn order to achieve balanced forms of urban infrastructure, which ensure comfort, safety and spatial order, when designing new solutions it is necessary to adopt a multi-facet approach which will combine everything that the local residents need but will respond harmoniously to the existing cultural landscape. It is therefore necessary to work out complex undertakings for the sake of planning and developing urban space. Coherent...
-
Improved Uniform Sampling in Constrained Domains for Data-Driven Modelling of Antennas
PublicationData-driven surrogate modelling of antenna structures is an attractive way of accelerating the design process, in particular, parametric optimization. In practice, construction of surrogates is hindered by curse of dimensionality as well as wide ranges of geometry parameters that need to be covered in order to make the model useful. These difficulties can be alleviated by constrained performance-driven modelling with the surrogate...
-
Threshold Attendance under Soft-Crash Model: TAG Protocol and Markovian Analysis
PublicationA realistic and systematic network evaluation should subsume an availability model and a failure model. We combine a "hard availability" model we call threshold attendance, whereby a certain minimum number of network elements must be present at any time, with a soft-crash failure model, whereby after experiencing a failure, a network element is still able to function correctly for a while in an emergency mode at a risk of a major...
-
Lighting requirements for pedestrian crossings - positive contrast
PublicationFor many years now in Poland there has been a large number of road accidents at pedestrian crossings during night periods [5, 11]. One of the technical solutions that can improve this condition is the use of proper lighting for pedestrian crossings. The designated pedestrian crossing should be visible in different weather conditions and at different times of the day. In case of night vision restrictions use artificial lighting...
-
Accelerated simulation-driven design optimisation of compact couplers by means of two-level space mapping
PublicationIn this study, the authors discuss a robust and efficient technique for rapid design of compact couplers. The approach exploits two-level space mapping (SM) correction of an equivalent circuit model of the coupler structure under design. The first SM layer (local correction) is utilised to ensure good matching between the equivalent circuit and the electromagnetic model at the component level. Subsequent global correction allows...
-
PV installations and the safety of residential buildings
PublicationThe dynamic development of the photovoltaic industry entails threats that have a direct impact on the safety of residential buildings. Appropriate design of a PV installation can be a challenge due to the multifaceted nature of this issue. The designer should take into account issues related to the selection of electrical parameters of the installation, adapting lightning and surge protection in accordance...
-
The role of sport in the Smart City concept
PublicationSport brings to cities innovative solutions that influence urban life, yet considerations about sport still rarely contribute to the development of the very popular smart city concept. This raises the question: what is the perception of sport in the city from the perspective of the smart city concept? One of the challenges of future urban policy is to provide initiatives that ensure the wellbeing and promote the model of a healthy...
-
Analysis of the Possibilities of Applying 3D Print Methods for the Needs of Ship-Building Industry
PublicationArticle presents the analysis of applying additive and hybrid manufacturing methods and its impact on dynamic stiffness of prepared samples. Dynamic analysis of the handle bracket specimens consisted in plotting the resonance curves and using these curves to estimate the dynamic stiffness of elements produced with additive manufacturing technology. Authors focused especially on 3D print in Fused Deposiotion Modeling/Fused Filament...
-
Testbed analysis of video and VoIP transsmission performance in IEEE 802.11 b/g/n networks
PublicationThe aim of the work is to analyze capabilities and limitations of different implementations of IEEE 802.11 technologies (IEEE 802.11 b/g/n), utilized for both video streaming and VoIP calls directed to mobile devices. Our preliminary research showed that results obtained with currently popular simulation tools can be drastically different than these possible in real-world environment, so, in order to correctly evaluate performance...
-
Experimental Study of Silent Sonar
PublicationStealth is a frequent requirement in military applications and involves the use of devices whose signals are difficult to intercept or identify by the enemy. The silent sonar concept was studied and developed at the Department of Marine Electronic Systems of the Gdansk University of Technology. The work included a detailed theoretical analysis, computer simulations and some experimental research. The results of the theoretical...
-
Design and distribution of air nozzles in the biomass boiler assembly
PublicationDue to energy crisis as well as increasing pollution of the environment, renewable energy sources usage increases all over the world. These facts encouraged authors to start research over developing a uniform biomass boiler calculation model. This paper presents a design of biomass boiler assembly created for ORC (Organic Rankine Cycle) unit since these systems could achieve strong position in energy industry....
-
Fast geometry scaling of UWB band-notch antennas
PublicationImplementation of band-notch capability plays an important role in the design of ultra-wideband (UWB) antennas. At the same time, appropriate sizing of antenna geometry parameters in order to precisely allocate the notch at the required frequency as well as to ensure sufficient reflection level is quite challenging and has to be based—for reliability reasons—on full-wave electromagnetic (EM) simulations of the structure. In this...
-
Comparison of Traffic Flow Models with Real Traffic Data Based on a Quantitative Assessment
PublicationThe fundamental relationship of traffic flow and bivariate relations between speed and flow, speed and density, and flow and density are of great importance in transportation engineering. Fundamental relationship models may be applied to assess and forecast traffic conditions at uninterrupted traffic flow facilities. The objective of the article was to analyze and compare existing models of the fundamental relationship. To that...
-
A nontargeted approach to determine the authenticity of Ginkgo biloba L. plant materials and dried leaf extracts by liquid chromatography-high-resolution mass spectrometry (LC-HRMS) and chemometrics
PublicationThe lack of stringent regulations regarding raw materials for herbal supplements used for medicinal purposes has been a constant challenge in the industry. Ginkgo biloba L. leaf extracts attract consumers because of the supposed positive effect on mental performance and memory. Supplements are produced using dried leaf materials and standardized leaf extracts such as EGb 761. Adulteration of Ginkgo biloba L. plants and extracts...
-
Adaptive traffic optimization using Variable Speed Limits; Adaptacyjna optymalizacja ruchu drogowego przy pomocy zmiennych ograniczeń prędkości
PublicationVariable speed limits (VSL) is an intelligent transportation system (ITS) solution for traffic management. The speed limits can be changed dynamically in order to adapt to traffic, weather, or road surface conditions. This paper presents an approach for such an adaptive traffic control where the primary goal is to ensure traffic safety and efficiency of the traffic control system (fast response to dynamically changing traffic,...
-
Real estate investment trusts in Turkey: Structure, analysis, and strategy
PublicationPurpose-Aim of this study is to make the determinations related to the problems mentioned in the REIT sector in Turkey, to offer a solution for this issue, and to ensure the classification in the sector by adhering to the financial data of the REITsMethodology-Financial data set of the REITs was firstly standardized by using median instead of mean. Then, the scoring was performed according to defined coefficients....
-
SZACOWANIE ZAWARTOŚCI BENZO(a)PIRENU W PYLE ZAWIESZONYM PM10 W AGLOMERACJI TRÓJMIEJSKIEJ ZA POMOCĄ WIELOWYMIAROWEJ REGRESJI LINIOWEJ=ESTIMATION OF BENZO(A)PYRENE CONTENT IN SUSPENDED DUST PM10 IN TRI-CITY AGGLOMERATION USING MULTIDIMENSIONAL LINEAR REGRESSION
PublicationW pracy przedstawiono próbę oszacowania przy pomocy wielowymiarowej regresji liniowej modelu empirycznego opisującego czynniki wpływające na zawartość B(a)P w pyle zawieszonym PM10 w Aglomeracji Trójmiejskiej w latach 2008-2011. Na przestrzeni tych lat średnioroczne stężenie B(a)P w PM10 wzrosło ponad dwukrotnie i ponad trzykrotnie przewyższa poziom docelowy. Z przeprowadzonych analiz wynika, że główną przyczyną wzrostu stężenia...
-
Biometryczna kontrola dostępu
PublicationOpisano szczegółowo algorytm detekcji oraz identyfikacji człowieka na podstawie punktów nodalnych twarzy. Zdefiniowano pojęcia: biometria, proces pomiaru biometrycznego, metody biometrycznej identyfikacji oraz kontrola dostępu. Przedstawiono opis opracowanego systemu biometrycznej identyfikacji wykorzystującego sztuczne sieci neuronowe. Podano wyniki badań oraz przeprowadzono ich wnikliwą dyskusję.Biometrics is the study of automated...
-
Multimedia System for Environmental Noise Monitoring. [Multimedialny System Monitorowania Hałasu Środowiskowego]
PublicationIntroductionNumerous reports relating to noise threats in Poland indicate that they occur commonly. The noise has an enormous impact on the health and life quality of the human beings. Noise pollution in Poland is greater than in others UE countries, moreover it has been increased recently. Taking into account 2002/49/WE directive related to the control and assessment of environmental noise a necessity of monitoring these threats...
-
Zastosowanie redundancji w siłowniach okrętowych statków oceanotechnicznych
PublicationSystemy wytwarzania energii i napędu statków oceanotechnicznych muszą mieć bardzo wysoki poziom niezawodności. Utrata zdolności do wykonywania funkcji przez ich elementy strukturalne z reguły powoduje bardzo wysokie straty ekonomiczne. Straty te mogą być zwiększone przez niemożność wykorzystania tzw. okna pogodowego, skutkującego odłożeniem w czasie zaplanowanych operacji oceanotechnicznych. W celu zapewnienia niezawodnej realizacji...
-
Analytical methods for exhaustive characterization of Brassica plants and dietary products based on them
PublicationGlucosinolates (GLs), and particularly two classes of their degradation products - isothiocyanates (ITC) and indoles - released upon myrosinase catalyzed hydrolysis, belong to the most promising chemopreventive dietary components. Despite their wide use in plant research, studies on chemopreventive mechanisms and industrial utilization in the production of e.g. dietary supplements, the methods of reliable characterization of myrosinase-GLs...
-
Utilization of the zero unitarization method for the building of a ranking for diagnostic marine engine parameters
PublicationChanging some of the parameters of the engine structure affects the emission of harmful components in the exhaust gases This primarily concerns damage in the cargo exchange system as well as in the fuel system and engine boost system. Changes in emissions of harmful compounds are often ambiguous, depending largely on the parameters that shape the combustion process. An additional problem is that often simple but undesired interactions...
-
Reliability and Validity of Optoelectronic Method for Biophotonical Measurements
PublicationReliability and validity of measurements is of utmost importance when assessing measuring capability of instruments developed for research. In order to perform an experiment which is legitimate, used instruments must be both reliable and valid. Reliability estimates the degree of precision of measurement, the extent to which a measurement is internally consistent. Validity is the usefulness of an instrument to perform accurate...
-
Poroelastic Road Surface – a Promising Road Traffic Noise Abatement Solution
PublicationRoad surfaces have a direct impact on the generation of noise by rolling tyres, the main and dominant source of noise of moving vehicles, as well as may affect propagation of noise emitted by all noise sources of a vehicle. Thus there is no doubt that pavement should be considered as one of the major potential road traffic noise abatement measure. Low noise pavements of existing types may in new conditions provide up to 8 dB of...
-
ANALYSIS OF POSSIBILITIES FOR THE USE OF VOLUME-DELAY FUNCTIONS IN THE PLANNING MODULE OF THE TRISTAR SYSTEM
PublicationTravel time is a measure commonly used for traffic flow modelling and traffic control. It also helps to evaluate the quality of traffic control systems in urban areas. Traffic control systems that use traffic models to predict changes and disruptions in vehicle flows have to use vehicle speed-prediction models. Travel time estimation studies the effects of traffic volumes on a street section at an average speed. The TRISTAR Integrated...
-
Evaluation of Body Surface Area Formulae Based on 3D Body Scans
PublicationHuman body surface area (BSA) is an established parameter for the calculation of chemotherapy drugs dosage, treatment of chronic hepatitis B, treatment of burns or for establishing a dosing regimen for antimicrobials. Although being a critical parameter, usage of modern 3D scanners, which would measure the exact BSA value, is often impossible in time-sensitive operations or for patients unable to withstand the scanning process....
-
Tacit Knowledge Sharing and Creativity. How to Derive Innovation from Project Teams?
PublicationModern companies are increasingly likely to work in a project management environment, which ensures their success in the implementation of innovation. The aim of the study is to prove that tacit knowledge is a mediator for creativity and project performance. Creativity as one of the crucial sources of innovation is stimulated by tacit knowledge. Bearing this fact in mind, the authors studied relations between tacit knowledge, creativity...
-
COMPARATIVE ANALYSIS OF RESULTS OF APPLICATION OF MARKOV AND SEMI-MARKOV PROCESSES TO RELIABILITY MODELS OF MULTI-STATE TECHNICAL OBJECTS
PublicationDuring rational operation of technical objects and systems various operational decisions are made and decision-making process itself should be consisted in selecting that considered most favourable out of all possible to be taken. Choice of such decision is possible after taking into account many different information items but it never be completely correct without accounting for data and indices dealing with reliability. In...
-
Improving depth maps of plants by using a set of five cameras
PublicationObtaining high-quality depth maps and disparity maps with the use of a stereo camera is a challenging task for some kinds of objects. The quality of these maps can be improved by taking advantage of a larger number of cameras. The research on the usage of a set of five cameras to obtain disparity maps is presented. The set consists of a central camera and four side cameras. An algorithm for making disparity maps called multiple...
-
Ionic thermoelectric effect in Cu2-δSe during phase transition
PublicationThe ionic Seebeck coefficient was studied in copper selenide with Cu1.99Se, Cu1.95Se and Cu1.8Se stoichiometry which was synthesized with a melt crystallization method. To measure the ionic Seebeck coefficient of copper ions, 0.15C6H12N4CH3I + 0.85CuI solid-state electrolyte was prepared. Electrolyte layers were pressed with copper selenide powder into a sandwich-like structure. At the temperature of 410 K, the materials have ionic...
-
Process zone in the Single Cantilever Beam under transverse loading. - Part II: Experimental
PublicationThis paper describes an experimental arrangement to evaluate stress/strain fields in the process zone of asymmetric adhesively bonded joints. A transparent polycarbonate flexible beam was bonded to an aluminium alloy rigid block with an epoxy adhesive in a Single Cantilever Beam (SCB) configuration. The flexible adherend was loaded in the direction parallel to the initial crack front at constant rate. To monitor strains induced...
-
The Use of Liquid Crystal Thermography in Selected Technical and Medical Applications—Recent Development
PublicationThermochromic liquid crystals (TLC) and true-colour digital image processing have been successfully used in non-intrusive technical, industrial and biomedical studies and applications. Thin coatings of TLC at surfaces are utilized to obtain detailed temperature distributions and heat transfer rates for steady or transient processes. Liquid crystals also can be used to make the temperature and velocity fields in liquids visible...
-
Selection of Visual Descriptors for the Purpose of Multi-camera Object Re-identification
PublicationA comparative analysis of various visual descriptors is presented in this chapter. The descriptors utilize many aspects of image data: colour, texture, gradient, and statistical moments. The descriptor list is supplemented with local features calculated in close vicinity of key points found automatically in the image. The goal of the analysis is to find descriptors that are best suited for particular task, i.e. re-identification...
-
Operational problems of large power diesel engines combusting biofuels, considered togetherwith assessment of their operation
PublicationWithin this article the issue of large power self ignition engines fed with biofuels has been undertaken. The analysis focused mainly on operation problems. There has been noticed some advantages and difficulties associated with the biofuel application to self ignition engines. The research problem has been characterised and the research purposes have been proposed enabling the most profitable formation of energetic features of...
-
The Use of Wavelet Analysis to Denoising of Electrocardiography Signal
PublicationThe electrocardiography examination, due to its accessibility and simplicity, has an important role in diagnostics of the heart ailments. It enables quick detection of various heart defects, undetectable by other kinds of diagnostic tools, so it is very popular. Nevertheless, the measured signal is exposed to a different disturbances. Among them, the electromagnetic interferences, drift of reference electrode and high frequency...