Filters
total: 1888
filtered: 1351
-
Catalog
Chosen catalog filters
displaying 1000 best results Help
Search results for: abandonment ratio
-
Transmission Quality Measurements in DAB+ Broadcast System
PublicationIn the age of digital media, delivering broadcast content to customers at an acceptable level of quality is one of the most challenging tasks. The most important factor is the efficient use of available resources, including bandwidth. An appropriate way of managing the digital multiplex is essential for both the economic and technical issues. In this paper we describe transmission quality measurements in the DAB+ broadcast system....
-
Effects of Xanthan Gum Biopolymer on the Permeability, Odometer, Unconfined Compressive and Triaxial Shear Behavior of a Sand
PublicationBiopolymers, which are microbially induced polymers, can be used as an alternative material to improve engineering performance of soils. In this paper, a laboratory study of 0.075-1.0 mm size sand and biopolymer (i.e., xanthan gum) mixtures with various mix ratios (0%, 0.5%, 1.0%, and 1.5%) was performed. The materials, specimen preparation, and test methods are described, as are the results of a suite of permeability, odometer, unconfined...
-
Modulo N Backoff Scheme for effective QoS differentiation and increased bandwidth utilization in IEEE 802.11 networks
PublicationThe paper presents a new "modulo N" channel access scheme for wireless Local Area Networks (WLANs). The novel solution derives from the Distributed Coordination Function (DCF) of the IEEE 802.11 standard, further elaborated as Enhanced Distribution Channel Access (EDCA) by the 802.11e draft specification. The main innovation concerns improvement of the binary exponential backoff scheme used for collision avoidance in 802.11 networks....
-
Optoelectronic system for monitoring of thin diamond layers growth
PublicationDevelopment of the optoelectronic system for monitoring of diamond/DLC (Diamond-Like-Carbon) thin films growth during mu PA ECR CVD (Microwave Plasma Assisted Electron Cyclotron Resonance Chemical Vapour Deposition) process is described. The multi-point Optical Emission Spectroscopy (OES) and Raman spectroscopy were employed as non-invasive optoelectronic tools. Dissociation of H-2 molecules, excitation and ionization of hydrogen...
-
Pendant Proton-Relays Systematically Tune the Rate and Selectivity of Electrocatalytic Ammonia Generation in a Fe-Porphyrin Based Metal-Organic Framework
PublicationElectrocatalytic nitrite reduction (eNO2RR) is a promising alternative route to produce ammonia (NH3). Until now, several molecular catalysts have shown capability to homogeneously reduce nitrite to NH3, while taking advantage of added secondary-sphere functionalities to direct catalytic performance. Yet, realizing such control over heterogeneous electrocatalytic surfaces remains a challenge. Herein, we demonstrate that heterogenization...
-
Strain-dependent behaviour of cold recycled material mixtures in cyclic compression tests
PublicationThe purpose of the study is to evaluate strain-dependent behaviour of Cold Recycled Material (CRM) mixtures using three frameworks typically applied for Hot Mix Asphalt (HMA): linear viscoelastic (LVE) limits; non-linearity directions; changes in rheological model parameters. To this aim, the complex modulus of three CRM mixtures with different bitumen-to-cement ratio (0.2, 0.6 and 1.8) was measured in cyclic compression mode,...
-
Impact of trajectory simplification methods on modeling carbon dioxide emissions from ships
PublicationModels of ship fuel consumption and emissions play an essential role in estimating global shipping’s greenhouse gas emissions. They are also widely used for verification of reported CO2 emissions for systems like EU MRV (Monitoring, Reporting and Verification) or IMO DCS (Data Collection System). Such models achieve high accuracy using historical spatiotemporal information about each ship from AIS data. However, this approach requires substantial...
-
Efficient optimization approaches for microwave assisted extraction of high-quality antioxidant compounds from Salvia officinalis L.: UHPLC-HRMS differential analysis of phenolic profiles obtained by ultrasound and microwave extraction
PublicationThe study aims to optimize MAE of total phenolic compounds (TPC) and antioxidant capacity from Salvia officinalis L. leaves using a definitive screening design (DSD) and I-optimal design. UHPLC-HRMS analysis was used to identify and compare the composition of MAE and UAE optimal extracts. The results showed that DSD and I-optimal design were successfully applied for the optimization of MAE targeting phenolics and other antioxidants...
-
Optimization of a Fabric Phase Sorptive Extraction protocol for the isolation of six bisphenols from juice pouches to be analysed by high performance liquid chromatography coupled with diode array detector
PublicationFabric Phase Sorptive Extraction (FPSE) combined with high pressure liquid chromatography using to diode array detection (HPLC-DAD) was applied for the simultaneous determination of bisphenols (BPA, BPB, BPC, BPE, BPF, BPS) in juice pouches. The FPSE procedure was optimized with regards to the critical parameters that affect the performance of the method including the selection of the FPSE membrane type and size, adsorption time,...
-
Cancer-selective, single agent chemoradiosensitising gold nanoparticles
PublicationTwo nanometre gold nanoparticles (AuNPs), bearing sugar moieties and/or thiol-polyethylene glycol-amine (PEG-amine), were synthesised and evaluated for their in vitro toxicity and ability to radiosensitise cells with 220 kV and 6 MV X-rays, using four cell lines representing normal and cancerous skin and breast tissues. Acute 3 h exposure of cells to AuNPs, bearing PEG-amine only or a 50:50 ratio of alpha-galactose derivative and...
-
The influences of the information and communication technology on the structural changes of Japanese energy sectors from 1985 through 2005: a statistical analysis
PublicationThe purpose of this study is to analyse the influences of information and communication technology (ICT) on the structural changes of Japanese energy sectors from 1985-2005. In this study, ICT is represented by two explanatory variables, namely: 1) computers, main parts and accessories; 2) telecommunications equipment. We employ a statistical tool in investigating the influences quantitatively, namely constrained multivariate regression...
-
DEPTH IMAGES FILTERING IN DISTRIBUTED STREAMING
PublicationIn this paper we discuss the comparison of point cloud filters focusing on their applicability for streaming optimization. For the filtering stage within a stream pipeline processing we evaluate three filters: Voxel Grid, Pass Through and Statistical Outlier Removal. For the filters we perform series of the tests aiming at evaluation of changes of point cloud size and transmitting frequency (various fps ratio). We propose a distributed...
-
Modification of thermal and rheological characteristics of bitumen by waste PET/GTR blends
PublicationWaste poly(ethylene terephthalate) (wPET)/ground tire rubber (GTR) blends with variable compositions were applied as low-cost modifiers into bitumen and their performance has been evaluated via morphological, thermal and rheological analyses. Depending on the weight ratio of wPET/GTR, dispersion of single/composite domains of waste polymers in the bitumen has promoted the interaction between bitumen and blend components. Fourier...
-
Rigid polyurethane foams modified with selected layered silicate nanofillers
PublicationThe aim of this study was to investigate the effect of three different nanofillers on the properties of rigid polyurethane foams, which were prepared by a one-step, laboratory-scale method from a two-component system at the ratio of NCO groups to OH groups equaled to 2. The reaction mixture consisted of the proper amounts of the commercial oligoether polyol, catalysts, water, nanoclays, and polymeric diphenylmethane diisocyanate....
-
Analytical method for calculation of heat source temperature drop for the Organic Rankine Cycle application
PublicationIn the paper presented are considerations on the cooperation of the limited capacity heat source with the Organic Rankine Cycle unit. Usually the heat source providing thermal energy to the Organic Rankine Cycle (ORC) may have twofold characteristics. It can be in the form of a single phase fluid, i.e. as hot exhaust gas or hot liquid, or in some cases it may be available as a phase changing fluid, as for example, technological...
-
Numerical study of turbulent flow and heat transfer of nanofluids in pipes
PublicationIn this work, Nusselt number and friction factor are calculated numerically for turbulent pipe flow (6 000 < Re < 12 000) with constant heat flux boundary condition using nanofluids. The nanofluid is modelled with the single-phase approach and the simulation results are compared with experimental data of Vajjha et al. [1]. Ethylene glycol and water, 60:40 EG/W mass ratio, as base fluid and SiO2 nanoparticles are used as nanofluid...
-
Assessment of microstructure, physical and thermal properties of bitumen modified with LDPE/GTR/elastomer ternary blends
PublicationLDPE/GTR/elastomer ternary blends with variable LDPE/GTR ratio and constant elastomer content were prepared via melt-compounding. Obtained LDPE/GTR/elastomer blends were applied as thermoplastic modifiers into bitumen. Microstructure, physical and thermal properties of the modified bitumen were determined. It was observed that chemical composition of LDPE/GTR/elastomer blends has significant influence on their density and rheological...
-
CPTU/DMT control of heavy tamping compaction of sands
PublicationHeavy tamping compaction method in cohesionless alluvial soil was evaluated with CPTU and DMT tests. Some examples of interpretation of soundings in pre-treated and compacted sands are given. The compaction work was performed in two stages. Compaction control was performed after each stage of tamping. Additional tests were performed two weeks after the compaction works completion to study the set-up effect. While typical increase...
-
Effect of coarse grain aggregate on strength parameters of two-stage concrete
Publication. Two-stage concrete (TSC) is a special type of concrete that the method of its construction and implementation is different from conventional one. In TSC, coarse aggregate particles are first placed in the formwork and voids between them are subsequently injected with a special cementations mixture. TSC has been successfully used in many applications, such as underwater construction, casting concrete sections congested with reinforcement...
-
Integrated Photocatalytic Advanced Oxidation System (TiO2/UV/O3/H2O2) for Degradation of Volatile Organic Compounds
PublicationSeveral advanced oxidation processes (AOPs) including photocatalytic processes were studied for effective treatment of complex model wastewater containing a wide variety of VOCs. The studies revealed synergistic effects of TiO2 based processes for improved degradation of the VOCs. A peroxone combined with TiO2/UV system (TiO2/UV/O3/H2O2) with a ratio between the oxygen source from the oxidant to chemical oxygen demand (COD) of...
-
Ammonia amendment promotes high rate lactate production and recovery from semi-continuous food waste fermentation
PublicationIn this study, a reliable approach using ammonia nitrogen was proposed to increase lactate production during semi-continuous food waste (FW) fermentation under mesophilic conditions. Both free ammonia nitrogen (FAN) and ammonium ion (NH4+-N) were present in mesophilic reactors, with a wide FAN/NH4+-N ratio variation due to the intermittent pH control. The investigation of responsible mechanisms revealed that the increased production...
-
Fast surrogate-assisted frequency scaling of planar antennas with circular polarisation
PublicationIn this work, the problem of computationally efficient frequency scaling (re-design) of circular polarisation antennas is addressed using surrogate-assisted techniques. The task is challenging and requires the identification of the optimum geometry parameters to enable the operation of the re-designed structure at a selected (required) centre frequency. This involves handling several performance figures such as the antenna gain,...
-
A Simple-Topology Compact Broadband Circularly Polarized Antenna With Unidirectional Radiation Pattern
PublicationIn this letter, a geometrically simple, reflector-backed single-point-fed circularly polarized (CP) antenna with unidirectional radiation pattern is presented. The structure comprises a simple coplanar waveguide (CPW) feeding circuit with an open slot etched on one side of the coplanar ground. The enhanced CP bandwidth is obtained by combining the loop mode, the slot mode, and the asymmetrical configuration of the coplanar ground...
-
A design framework for rigorous constrained EM-driven optimization of miniaturized antennas with circular polarization
PublicationCompact radiators with circular polarization are important components of modern mobile communication systems. Their design is a challenging process which requires maintaining simultaneous control over several performance figures but also the structure size. In this work, a novel design framework for multi-stage constrained miniaturization of antennas with circular polarization is presented. The method involves sequential optimization...
-
Turbulence model evaluation for numerical modelling of turbulent flow and heat transfer of nanofluids
PublicationIn this work, Nusselt number and friction factor are calculated numerically for turbulent pipe flow (Reynolds number between 6000 and 12000) with constant heat flux boundary condition using nanofluids. The nanofluid is modelled with the single-phase approach and the simulation results are compared with experimental data. Ethylene glycol and water, 60:40 EG/W mass ratio, as base fluid and SiO2 nanoparticles are used as nanofluid...
-
AN EXPERIMENTAL AND NUMERICAL STUDY ON THE PERFORMANCE OF AN INNOVATIVE VERTICAL-AXIS WIND TURBINE
PublicationThis paper introduces the innovative modification of the Savonius wind turbine being able to significantly increase efficiency in comparison with the classic design. This innovative design is equipped with a stator directing the flow. The presence of the stator increases the active surface area and generates higher torques acting on a shaft. Additionally, it makes it possible to take better advantage of wind energy and compensate...
-
Analysis of abrasive particle trajectories during single-sided lapping process with driven conditioning ring
PublicationIn this paper new kinematics systems were studied for a single lapping process. In order to ensure the constant profile wear of the tool a standard kinematic system can be changed. Lapping is carried out by applying loose abrasive grains between two surfaces and causes a relative motion between them. The result is a finish of multi-directional lay. During process, the mechanism of surface formation are decisively affected by a...
-
Comprehensive study on graphene hydrogels and aerogels synthesis and their ability of gold nanoparticles adsorption
PublicationGraphene hydrogels were prepared by ascorbic acid-assisted gelation of graphene oxide (GO) aqueous suspensions both in acidic and basic conditions. Different mass ratio of ascorbic acid (AA) to GO was used (namely 20:1 and 10:1). In order to eliminate the influence of AA on the final structure of hydrogels, samples without AA were prepared by a hydrothermal gelation of GO in an autoclave. An in-depth structural characterization...
-
Failure mode prediction for composite structural insulated panels with MgO board facings
PublicationSandwich panels are readily used in civil engineering due to their high strength to weight ratio and the ease and speed of assembly. The idea of a sandwich section is to combine thin and durable facings with a light-weight core and the choice of materials used allows obtaining the desired behaviour. Panels in consideration consist of MgO (magnesium oxide) board facings and expanded polystyrene core and are characterized by immunity...
-
An improved scalable method of isolating asphaltenes
PublicationA new, improved and scalable procedure of asphaltene fraction isolation is presented and compared to standard test methods. The new procedure uses 1:40 feedstock to solvent (n-heptane) ratio (g/mL), filtration through a cellulosic thimble and extensive washing in a Soxhlet type extractor. The group type composition and purity of the asphaltene fractions have been examined using thin-layer chromatography with flame-ionization detection....
-
Chromatographic lipophilicity determination using large volume injections of the solvents non-miscible with the mobile phase
PublicationA new perspective in the lipophilicity evaluation through RP-HPLC is permitted by analysis of the retentionfactor (k) obtained by injecting large volumes of test samples prepared in solvents immiscible withmobile phase. The experiment is carried out on representative groups of compounds with increasedtoxicity (mycotoxins and alkaloids) and amines with important biological activity (naturally occurringmonoamine compounds and related...
-
Fatigue Bending of V-Notched Cold-Sprayed FeCoCrNiMn Coatings
PublicationCold-spray coatings were produced by FeCoCrNiMn high-entropy alloy powders deposited on carbon steel substrate. The coatings were realized at intermediate temperature and high pressure (at 1100 °C and 7 MPa). The coating microstructure was characterized by scanning electron microscopy and X-ray diffraction, revealing a very dense deposition and high flattening ratio of the splatted particles. This had a large influence on the...
-
Efficiency evaluation of graduation process in Australian public universities
PublicationFirst-year attrition and on-time graduation are key challenges for contemporary universities, which determine their efficiency. Based on the benefit of the doubt approach, this study reports the efficiency of the graduation process in 37 Australian public universities. The super-efficiency model extended by restrictions on virtual weights is used. The proposed model considers the attrition rate and the on-time graduation rate separately...
-
Deep eutectic solvent (DES) with silver nanoparticles (Ag-NPs) based assay for analysis of lead (II) in edible oils
PublicationThis paper presents an application of silver nanoparticles impregnated by Deep Eutectic Solvents (DES) as ultrasonication aided microextraction system for lead (II) determination in edible oils. The paper presents a systematic optimization of method parameters and examples of its application for analysis of real samples. Maximum recovery for lead (II) extraction was obtained for choline chloride and phenol with a 1:2 molar ratio....
-
Deodorization of model biogas by means of novel non-ionic deep eutectic solvent
PublicationThe paper presents new non-ionic deep eutectic solvent (DES) composed of natural and non-toxic components i.e. guaiacol, camphor and levulinic acid in 1:1:3 molar ratio as a promising absorbent for removal of selected volatile organic compounds (VOCs) including dichloromethane, toluene, hexamethyldisiloxane and propionaldehyde from model biogas. The affi nity of DES for VOCs was determined as vapour-liquid coeffi cients and the...
-
Non-Contact Monitoring of ECG in the Home Environment—Selecting Optimal Electrode Configuration
PublicationCapacitive electrocardiography (cECG) is most often used in wearable or embedded measurement systems. The latter is considered in the paper. An optimal electrocardiographic lead, as an individual feature, was determined based on model studies. It was defined as the possibly highest value of the R-wave amplitude measured on the back of the examined person. The lead configuration was also analyzed in terms of minimizing its susceptibility...
-
Anti-plane shear waves in an elastic strip rigidly attached to an elastic half-space
PublicationWe consider the anti-plane shear waves in a domain consisting of an infinite layer with a thin coating lying on an elastic half-space. The elastic properties of the coating, layer, and half-space are assumed to be different. On the free upper surface we assume the compatibility condition within the Gurtin–Murdoch surface elasticity, whereas at the plane interface we consider perfect contact. For this problem there exist two possible...
-
Experimental and analytical analysis of punching shear in flat slabs supported on column topped with concrete head
PublicationAn experimental laboraatory test of the two series of slab-column elements topped with drop panels of varying sizes is described in this paper. The scope of the paper is to investigate the influence of the drop panel size and stiffness on the behaviour of the connection between the flat slab and the column topped by the concrete head. The impact of the head size and stiffness is analysed analytically and experimentally. The experimental...
-
Shear band evolution phenomena in direct shear test modelled with DEM.
PublicationA direct shear test is widely used in the geotechnical engineering field. It is an easy and quick test to measure the shear properties of soil. This test often replaces more expensive and difficult tri-axial shear test. Despite that the direct shear test is known and used for a long time, it is still not well investigated at the grain scale. This paper deals with the micro behaviour of the cohesionless sand inside the direct shear...
-
Evaluation of pounding effects between reinforced concrete frames subjected to far-field earthquakes in terms of damage index
PublicationIn this paper, three different damage indexes were used to detect nonlinear damages in two adjacent Reinforced Concrete (RC) structures considering pounding effects. 2-, 4- and 8-story benchmark RC Moment Resisting Frames (MRFs) were selected for this purpose with 60%, 75%, and 100% of minimum separation distance and also without any in-between separation gap. These structures were analyzed using the incremental dynamic analysis...
-
Structural Assessment of Reinforced Concrete Beams Incorporating Waste Plastic Straws
PublicationThe behavior of reinforced concrete beams containing fibers made of waste plastic straws (WPSs) under the three point bending test is examined. The effect of WPS fiber addition on the compressive and split tensile strength is reported. Four concrete mixes were prepared. The control mix PS-0 had a proportion of 1 cement: 1 sand: 2 coarse aggregate and a water cement ratio of 0.4. In the other three mixes PS-0.5, PS-1.5 and PS-3,...
-
Mechanizmy komunikacji w rozproszonych systemach specjalnego przeznaczenia
PublicationZadania ochrony i bezpieczeństwa granic państwa realizowane przez Straż Graniczną wymagają wsparcia ze strony nowoczesnych systemów Technologii Informacyjnych (TI) uwarunkowanych ich specjalnym przeznaczeniem. Z uwagi na charakter tej służby, rozwiązania dla jej potrzeb muszą być realizowane jako systemy rozproszone umożliwiające przenoszenie i przetwarzanie informacji głosowych oraz różnorodnych danych, w tym specjalnego przeznaczenia....
-
Eksperymentalna analiza współczynników oporów lokalnych dla wybranych kształtek i złączek w systemach rur wielowarstwowych
PublicationArtykuł poświęcony jest analizie wartości współczynników oporów lokalnych dla wybranych kształtek i złączek pracujących w instalacjach z rur wielowarstwowych z tworzyw sztucznych. Badaniom poddano elementy o średnicach DN16, DN20, DN25, powszechnie wykorzystywane we współczesnych instalacjach sanitarnych. W pracy przedstawiono wybrane wyniki badań laboratoryjnych (dla rozszerzeń, kolanek i trójników) oraz ich porównanie z wartościami...
-
Accuracy analysis of the RSSI BLE SensorTag signal for indoor localization purposes
PublicationIn this paper we describe possibility of use the RSSI signal (Radio Signal Strength Indication) from Texas Instruments SensorTag CC2650 for indoor positioning purposes. This idea is not a new but in our opinion it is possible to use SensorTags with Bluetooth LE wireless interface for positioning inside buildings in such applications as people findings in hospitals, senior come care, etc. RSSI is mostly selected as the sensor localization...
-
Adaptive Method of Raster Images Compression and Examples of Its Applications in the Transport Telematic Systems
PublicationThe paper presents a concept and exemplary application of an adaptive method of compression of raster images which may be applied, i.a. in ITS systems. The described method allows to improve the efficiency of systems belonging to ITS category, which require transmission of large volumes of image data through telecommunications networks. The concept of the adaptive method of compression of raster images described in the paper uses...
-
LSTM-based method for LOS/NLOS identification in an indoor environment
PublicationDue to the multipath propagation, harsh indoor environment significantly impacts transmitted signals which may adversely affect the quality of the radiocommunication services, with focus on the real-time ones. This negative effect may be significantly reduced (e.g. resources management and allocation) or compensated (e.g. correction of position estimation in radiolocalisation) by the LOS/NLOS identification algorithm. This paper...
-
5G Technologies in Intelligent Transport Systems - Architectures, Virtualization and Network Slicing
PublicationIn the paper, 5G communication technologies implemented for Intelligent Transport Systems are discussed. Firstly, the essence of the 5G system concept is presented, and the problem of network functions virtualization (NFV) is analyzed. Moreover, the principle of virtualization is explained. Secondly, the analysis of network slicing is performed, from the point of view of transport systems implementation in the...
-
Research on Quality Requirements of Data Transmission Services in RSMAD
PublicationThe paper presents a results and analysis of research of the quality of service requirements (defined by the QoS attributes) for imaging data transmission services using Radio System for Monitoring and Acquisition of Data from Traffic Enforcement Cameras (in short RSMAD). The paper also presents and discusses results of test on the impact of the size of photos from traffic enforcement cameras on the average transmission time. These...
-
The trajectories of the financial crisis of companies at risk of bankruptcy
PublicationThis article concerns the assessment of the trajectory of the collapse of enterprises in Central Europe. The author has developed a model of a Kohonen artificial neural network. This model was used to determine 6 different classes of risk and was allowed to graphically determine the 5- to 10-year trajectory of going bankrupt. The study used data on 140 companies listed on the Warsaw Stock Exchange. This population was divided into...
-
New Simple and Robust Method for Determination of Polarity of Deep Eutectic Solvents (DESs) by Means of Contact Angle Measurement
PublicationThe paper presents a new method for evaluating the polarity and hydrophobicity of deep eutectic solvents (DESs) based on the measurement of the DES contact angle on glass. DESs consisting of benzoic acid derivatives and quaternary ammonium chlorides–tetrabutylammonium chloride (TBAC) and benzyldimethylhexadecylammonium chloride (16-BAC)—in selected molar ratios were chosen for the study. To investigate the DESs polarity, an optical...