Search
Filters
total: 6298
filtered: 4411
-
Catalog
Chosen catalog filters
displaying 1000 best results Help
Search results for: TIDES MEASUREMENTS
-
Measurement report: Spatial variations in ionic chemistry and water-stable isotopes in the snowpack on glaciers across Svalbard during the 2015–2016 snow accumulation season
PublicationThe Svalbard archipelago, located at the Arctic sea-ice edge between 74 and 81∘ N, is ∼60 % covered by glaciers. The region experiences rapid variations in atmospheric flow during the snow season (from late September to May) and can be affected by air advected from both lower and higher latitudes, which likely impact the chemical composition of snowfall. While long-term changes in Svalbard snow chemistry have been documented in...
-
O wyszukiwaniu niepoprawnych pomiarów w systemach DCS obiektów energetycznych = On search for incorrect measurement results in distributed control systems (DCS) of power objects
PublicationPrzedyskutowano problem rozpoznawania degradacji mierników pomiarowych w systemach DCS dużych obiektów energetycznych, przy równoczesnym występowaniu degradacji eksploatacyjnej urządzeń składowych tych obiektów. Zastosowano sieć neuronową (SNN) o skokowych funkcjach przejścia. Zastosowana SNN wykazała wysoką jakość. Sprawdzono możliwości rozpoznawania obu typów degradacji występującej w zastosowaniu do tzw. degradacji dwukrotnych.
-
Corrigendum to “Fatigue life improvement using low transformation temperature weld material with measurement of residual stress” [Int. J. Fatigue 164 (2022) 107137]
PublicationWelding processes often produce high levels of tensile residual stress. Low transformation temperature (LTT) welding wires utilise phase transformation strains to overcome the thermal contraction of a cooling weld. In this paper, the residual stress within each weld was quantified using the milling/strain gauge method, being the strain change measured as the weldment was milled away. The fatigue tests were conducted under uniaxial...
-
The Effect of Full-Cell Impregnation of Pine Wood (Pinus sylvestris L.) on Changes in Electrical Resistance and on the Accuracy of Moisture Content Measurement Using Resistance Meters
PublicationThe impact of the full-cell impregnation of pine wood was investigated with respect to changes in electrical resistance and the accuracy of moisture content measurement. This study compared the resistance of impregnated and untreated pine timber harvested from the northern part of Poland (Pomeranian region). The wood was impregnated by the vacuum-pressure method. The preservative (TANALITH E 3475) and coloring (TANATONE 3950) agents...
-
Comparative field test for measurement of PM10 dust in atmospheric air using gravimetric (reference) method and b-absorption method (Eberline FH 62-1)
PublicationThe paper presents the results of a field test carried out in Gdansk region between 01-01-2010 and 31-12-2010 in order to demonstrate equivalence of the Eberline FH 62-1 sampler to the reference gravimetric method of suspended PM10 dust measurement. The differences in PM10 dust concentration provided by both methods have been discussed for different seasons of the year. A method of estimation of the correction factors/correction...
-
Different Ways to Apply a Measurement Instrument of E-Nose Type to Evaluate Ambient Air Quality with Respect to Odour Nuisance in a Vicinity of Municipal Processing Plants
PublicationThis review paper presents different ways to apply a measurement instrument of e-nose type to evaluate ambient air with respect to detection of the odorants characterized by unpleasant odour in a vicinity of municipal processing plants. An emphasis was put on the following applications of the electronic nose instruments: monitoring networks, remote controlled robots and drones as well as portable devices. Moreover, this paper presents...
-
Measuring and Analyzing Audio Levels in Film, Commercials, and Movie Trailers Using Leq(A) Values and the LUFS Loudness Model . Analiza pomiarów dźwięku w filmie oraz w reklamach filmowych z wykorzystaniem modelu głośności
PublicationThe purpose of this paper is to describe the measurement of loudness levels in movies, movie trailers, and commercials displayed before feature films at movie theaters. In the initial section, the paper discusses the issues related to measurement of loudness levels, provides recommendations regarding permissible loudness levels during movie screenings, and mentions the applied units of measurement. The following section of the...
-
Measurements of photoionization of mercury atoms into the 6s 2S1/2, 5d96s2 2D5/2 and 5d96s2 2D3/2 ionic states over the energy range from 10.5 eV to 18.7 eV
PublicationPhotoionization of mercury atoms into the three lowest ionic states, 5d106s 2S1/2, 5d96s2 2D5/2 and 5d96s2 2D3/2 has been studied in the photon energy ranges from their respective thresholds to 18.7 eV. The photoionization spectra were obtained with high energy resolution at an angle of 0° with respect to the polarization vector of the photon beam. The high energy resolution and sensitivity achieved in the measurements permitted...
-
Eine Eeue Technik zur Präzisen Rissfortschrittsmessung im DCB oder im Keilversuch = A novel technique for precise crack length measurement in the DCB or wedge test
PublicationDiverse methods have been tried to study crack length, most basic relying on direct, or microscopic, observation of the crack tip position. Optical correlation, both lasermoiré and speckle interferometry, a single strain gauge and displacement sensorshave also been employed. Crack length measurement is, however, delicate. We present a novel method making use of strain gauges attached to one of the adherends.
-
Mobile Laser Scanning Calibration on a Marine Platform
PublicationThe article describes the method of calibration of the Riegl VMZ-400 mobile scanning system on a floating platform and an experiment aimed at conducting measurements from a previously calibrated instrument. The issue of factors affecting the quality of measurements was discussed. Mobile laser scanning is an increasingly popular measurement solution, but it is still innovative on a European scale. The use of a floating platform...
-
Measurement of plasma 25-hydroxyvitamin D2, 25-hydroxyvitamin D3 and 3-epi-25-hydroxyvitamin D3 in population of patients with cardiovascular disease by UPLC-MS/MS method
Publication -
<title>Modular version of SIMCON, FPGA based, DSP integrated, LLRF control system for TESLA FEL part II: measurement of SIMCON 3.0 DSP daughterboard</title>
Publication -
Design and modeling of the piezoelectric motor based on three resonance actuators
PublicationThis paper describes a piezoelectric motor which combines advantages from two existing piezoelectric motors topologies. The research work presents the design, simulations and measurements of the piezoelectric motor with three rotation-mode actuators. The aim of the project was to obtain the high speed piezoelectric motor. Other advantages of this conception are blocking torque, short response times, the ability to work in a hostile...
-
Temperature influence on tire/road noise evaluated by the drum method
PublicationAmbient air and road surface temperatures substantially affect the road vehicle noise emission. The temperature influence on tire/road noise depends mainly on tire-road combination. It is different for dense and porous pavements, for bituminous and cement ones. It differs also depending on tires. The correction procedures for temperature effect are still under consideration and preparation. Laboratory experiment was prepared to...
-
Modeling nutrient removal and energy consumption in an advanced activated sludge system under uncertainty
PublicationActivated sludge models are widely used to simulate, optimize and control performance of wastewater treatment plants (WWTP). For simulation of nutrient removal and energy consumption, kinetic parameters would need to be estimated, which requires an extensive measurement campaign. In this study, a novel methodology is proposed for modeling the performance and energy consumption of a biological nutrient removal activated sludge system...
-
Time-current tripping characteristics of RCDs for sinusoidal testing current
PublicationLow-voltage electrical installations are verified initially – before being put into operation, as well as periodically – during their utilization. According to the IEC standards, the scope of the verification includes measurements of both the tripping current and the disconnection time of residual current devices (RCDs). Experiences in RCDs testing show that disconnection times of two or more similar RCDs can be quite different....
-
Reply to Comment on ‘Nanodiamond incorporated human liver mimicking phantoms: prospective calibration medium of magnetic resonance imaging’
PublicationDependence of the spin–lattice (T1) relaxation times on the nanodiamond concentration in human liver phantoms is discussed. Factors affecting stability and and reproducibility of these phantoms are presented. The need for comparative measurements on multiple MRI scanners for better understanding of potential variations in the obtained imaging data is emphasised.
-
High frequency test measurements on physical model of power transformer with use of FRAX analyzer Streszczenie. W niniejszym artykule przedstawiono pomiary testowe SFRA wykonane na modelu fizycznym transformatora elektroenergetycznego
Publication -
Wpływ procedury termostatowania oraz sposobu przeprowadzenia pomiaru na wyniki oceny zawartość fazy stałej w wybranych tłuszczach.Influence of procedure of termostating and methods of measurements on solid fat content in selected fats.
PublicationW pracy przedstawiono sposoby przygotowania próbek tłuszczów przed oznaczeniem zawartości fazy stałej opracowane przez organizacje międzynarodowe oraz instytucje specjalizujące się w chemii i analizie tłuszczów. Porównano stosowane procedury termostatowania i metody pomiaru, oraz zbadano ich wpływ na zawartość fazy stałej w wybranych tłuszczach.
-
Sound Field Intensity Measurements and Visualization around the Human Head Model . Rozkłąd natężenia pola akustycznego w komorze bezechowej obecności sztucznej głowy i w przypadku braku jej obecności
PublicationThe main goal of this research study was to measure and visualize sound field intensity distribution in and without presence of the human head model. Measurements were performed in the anechoic chamber with the 5 cm grid. Experimental setup consisted of a multitone generator, two loudspeakers, human head model, intensimetric probe, the Cartesian robot applied for precise positioning of the acoustic sensor, and an analyzer. Based...
-
Person Tracking in a Ferry Environment Using Ultra-Wide Band Radio Interface
PublicationThis article presents research and analysis of effectiveness of tracking moving people in an environment of passenger ferry, using measurements of propagation time of ultra-wide band radio signal (UWB - Ultra-Wide Band). Constructed measurement stand and results of measurements carried out in a real propagation conditions were shortly discussed.
-
Poziomy stężeń lotnych związków chlorowcoorganicznych w wodach opadowych na terenie dużej aglomeracji miejskiej = Measurement of volatile chloroorganic compounds in urban rainwater (Gdańsk, Sopot, Gdynia)
PublicationW 105 próbkach opadów atmosferycznych (deszcz, deszcz ze śniegiem) zebranych z terenu Trójmiasta w okresie od listopada 2000 r. do maja 2001 r. oznaczano chloro - i bromopochodne metanu, etanu i etenu (7 różnych związków). Najczęściej wykrywanymi i oznaczanymi były: chloroform i czterochlorek węgla, (bardzo popularne rozpuszczalniki stosowane jako środki chłodzące i czyszczące). Najwyższe stężenia obserwowano w przypadku chloroformu,...
-
Measurement of activity coefficients at infinite dilution of organic solutes in the ionic liquid 1-hexyl-1,4-diaza[2.2.2]bicyclooctanium bis(trifluoromethylsulfonyl)imide using gas–liquid chromatography
PublicationBased on gas–liquid chromatography (GLC) retention data, activity coefficients at infinite dilution of 39 different solutes in the ionic liquid 1-hexyl-1,4-diaza[2.2.2]bicyclooctanium bis(trifluoromethylsulfonyl)imide ([HDABCO][NTf2]) have been determined. Measurements covered a broad range of types of organic solutes including alkanes, alcohols, ketones, benzene derivatives and McReynold’s compounds. Activity coefficients were...
-
Pomiary naprężeń w warstwie wierzchniej stali duplex metodą dyfrakcji promieniowania rentgenowskiego g-sin2Ψ = Residual stress measurements in duplex steel surface layers by g-sin2Ψ x-ray diffraction method
PublicationPrzedstawiono wyniki pomiarów naprężeń w warstwie wierzchniej z wykorzystaniem metody dyfrakcji promieniowania rentgenowskiego g-sin2. Wyjaśniono zasady przeprowadzania pomiarów naprężeń na próbkach walcowych o małej średnicy. Badania prowadzono na próbkach okrągłych ze stali duplex, poddanych procesom nagniatania. Stwierdzono występowanie naprężeń ściskających w warstwach powierzchniowych wszystkich badanych próbek oraz istotne...
-
Estimation of transmission quality in cellular systems based on indicators measured by the radio module
PublicationThe article presents a measurement stand for testing transmission quality in cellular systems such as LTE, NB-IoT, UMTS and GSM. The results of BLER and throughput measurements for various propagation conditions as well as results of quality indicators appropriate for mentioned technologies measured by commercial radio module are presented. Those measurements were utilized to analyze the possibility of estimating the transmission...
-
Road texture influence on tire rolling resistance
PublicationTire rolling resistance is one of the most important resistive forces acting on road vehicles. It depends on tire and surface characteristics as well as vehicle operating parameters. This paper deals with the influence of road surface texture on rolling resistance of passenger car tires. Results of road measurements performed on variety of road surfaces are presented.
-
Research project BRIK: development of an innovative method for determining the precise trajectory of a railway vehicle
PublicationIn the paper the essential assumptions regarding a research project implemented by a consortium of Gdansk University of Technology and Gdynia Maritime University are presented. The project has been commissioned by National Center of Research and Development with cooperation with Polish Railways (PKP Polskie Linie Kolejowe S.A.). The project is focused in implementation of modern measurement techniques using Global Navigation Positioning...
-
Intelligent equalizer solution employing music genre and the room characteristics analysis
PublicationThe paper presents an intelligent equalizer solution based on room acoustic conditions and music genre analysis. A series of acoustic characteristic measurements are performed for checking the concept proposed. White noise (reference signal) and audio excerpts belonging to six music genres are utilized as excitation signals in measurements. This results in registration of frequency responses of rooms and reverberation times. Signals...
-
Influence of Sn and Pb Ions Substitutions on Dielectric Properties of Barium Titanate
PublicationThe results of the microstructural and dielectric measurements of (Ba1-xPbx)(Ti1-xSnx)O3 (BPTSx) (x = 0, 0.05, 0.10, 0.30) polycrystalline samples are presented. The samples were obtained by means of a high temperature synthesis and their expected stoichiometry was confirmed by energy dispersive spectroscopy (EDS) measurements. The dielectric properties of BPTSx were studied with the use of broadband dielectric spectroscopy. The...
-
Fiber-optic sensors based on microspheres with nanocoatings (Zastosowanie mikrosfer optycznych z cienkowarstwowymi pokryciami w czujnikach światłowodowych)
PublicationTemperature is one of the most important physical quantities. Temperature measurements are used in every field of life, especially electronics, electrical engineering, energy-related fields, including energy source and storage devices. The goal of this dissertation is to design and optimize the microsphere-based fiber-optic sensors construction for measurement of the sensor surrounding medium temperature, including selection of...
-
Electrochemical capacitor temperature fluctuations during charging/discharging processes
PublicationThepaperpresentsaproposalofusingadditionalstatisticalparameterssuchas:standarddeviation,variance, maximum and minimum increases of the observed value that were determined during measurements of temperature fields created on the surface of the tested electrochemical capacitor. The measurements were carriedoutusingthermographicmethodsinordertosupportassessmentoftheconditionofelectrochemical capacitorunderclassicdurabilitytestsbasedonmethodsofdeterminationofcapacityandequivalentseries...
-
Assessment of the Accuracy of a Virtual Multi-Channel Temperature Measuring Instrument
PublicationThe multi-channel temperature measurement system developed works with NTC thermistors. The article presents the results of theoretical and empirical evaluation of accuracy obtained in measurement channels. The basis for the theoretical assessment is the mathematical model for each of the measurement channels and the characteristics of the system elements included in the circuits of the measurement channel. Two different methods were...
-
O zastosowaniu metody prądów wirowych do technicznego pomiaru własności elektrycznych i magnetycznych metali = About application of eddy current method for technical measurement of electric and magnetic properties of metals
PublicationOpisano wyniki badań nad wykorzystaniem efektu prądów wirowych do badania własności elektrycznych i magnetycznych metali. Badania wykonano za pomocą sondy różnicowej. Wyniki pomiarów zależności częstotliwościowej wykonane dla modelowych materiałów porównano z wynikami modelowania metodą elementów skończonych.
-
Adaptive acoustic crosstalk cancellation in mobile computer device
PublicationThe cancellation of acoustic crosstalk is employed to enhance the stereo image in mobile listening conditions. A practical setup employing a mobile computer is employed. The adaptation of the crosstalk cancellation filter to the position of the listener's head is featured. The measurement evaluating the possibility of practical application of the method are described. The head and torso simulator was used for measurements. The...
-
Analysis of the Accuracy of Pulse Estimation Using Smart Watches
PublicationThe purpose of this paper is to perform an analysis of the accuracy of the pulse estimation by comparing readings from a smartwatch with readings from medical devices. The study required writing applications that allow continuous pulse measurement. As a result, two applications were created for the smartwatch. The first one is dedicated to Android Wear devices, while the other one is compatible with Tizen watches. The next step...
-
UAV IN TODAYS PHOTOGRAMMETRY – APPLICATION AREAS AND CHALLENGES
PublicationThere a few important factors, that nowadays, unmanned aerial vehicles (UAV) are used by wider community, and for cases and applications, that cannot be performed never before. Small UAVs, as a photogrammetry measurement tool provide flexibility, reliability, are safe and easy to use, can be deployed in minutes, initial measurement can be delivered yet on the field, and final accurate measurements are calculated in a very short...
-
Solid state versus fiber picosecond infrared lasers applied to two-photon vision tests
PublicationDevelopment of new microperimetric tools dedicated for imaging of early functional changes in the retina may help in the monitoring of various ocular diseases progression e.g. Age-Related Macular Degeneration. Recently described two-photon vision may be applied to microperimetric devices. Many subjects with well-known disease history could be investigated with newly developed instrumentation that tests ability of human eye to perceive...
-
Mobile application technology in levelling
PublicationThe topic of this article is the use of mobile application technology in geodetic measurements with an emphasis on levelling. Reference points were registered as data from levelling benchmarks, performed with a traditional dumpy level. The created application allowed the recording of measurements on location, sending them to a remote server for processing and preparing a report to be saved in a database. The project was to decrease...
-
Determining the leakage current resistive component by the orthogonal vector method
PublicationThe measurement of the metal – oxide surge arresters (MOSA) leakage current and the analysis of its components is a key diagnostic criterion according to technical standards. During on site MOSA condition assessment, the easy way is based on the measurement only leakage current, without the inconvenient live working measurements of supply voltage. Orthogonal vectors method of determination the resistive leakage current is presented....
-
System of monitoring of the Forest Opera in Sopot structure and roofing
PublicationThe authors present a solution realized in Forest Opera (name in Polish: Opera Leśna) in Sopot (Poland) in connection with the modernization and construction of a new roof. The complicated structure of the roof of the facility and the used covering in form of membrane made of technical fabric required (for security reasons) to install the unit of devices allowing for the continuous geodetic monitoring of the facility. Monitoring...
-
Szacowanie niepewności pomiarowej układu do diagnostyki łożysk opartej na analizie mocy chwilowej
PublicationW artykule przedstawiono sposób szacowania niepewności układu pomiarowego, składającego się z dzielnika napięcia oraz bocznika, który wykorzystano do badań diagnostycznych łożysk silników indukcyjnych. Wyniki analizy metrologicznej pozwalają sprecyzować, jakiej niepewności pomiarowej można się spodziewać, dokonując badań diagnostycznych łożysk silników indukcyjnych w określonych warunkach, na stanowisku badawczym metodą...
-
Szacowanie niepewności pomiarowej układu do diagnostyki łożysk opartej na analizie mocy chwilowej.
PublicationW artykule przedstawiono metodologię szacowania niepewności pomiarowej wykorzystanego do badań diagnostycznych łożysk silników indukcyjnych układu pomiarowego, składającego się z dzielnika napięcia oraz bocznika. Wyniki tych analiz pozwalają spre-cyzować, jakiej niepewności pomiarowej można się spodziewać, dokonując badań diagnostycznych łożysk silników indukcyjnych w określonych warunkach, na stanowisku badawczym metodą pomiaru...
-
Rolling Resistance And Tire/Road Noise on Rubberized Asphalt Pavement In Poland
PublicationThe paper presents results of tire/road noise and rolling resistance measurements performed on stone-matrix asphalt (SMA) that contains rubberized asphalt developed and produced by the company in Poland. Bituminous binder was modified with polymer and additive of crumb rubber. First observations of asphalt mixture with the new kind of modified bitumen used on the field section are presented. Rolling resistance of passenger car...
-
Methodology for the Correction of the Spatial Orientation Angles of the Unmanned Aerial Vehicle Using Real Time GNSS, a Shoreline Image and an Electronic Navigational Chart
PublicationUndoubtedly, Low-Altitude Unmanned Aerial Vehicles (UAVs) are becoming more common in marine applications. Equipped with a Global Navigation Satellite System (GNSS) Real-Time Kinematic (RTK) receiver for highly accurate positioning, they perform camera and Light Detection and Ranging (LiDAR) measurements. Unfortunately, these measurements may still be subject to large errors-mainly due to the inaccuracy of measurement of the optical...
-
Evaluation of the prediction ability of air pollutants based on the electronic nose responses
PublicationElectronic noses are able to perform on-line measurements of the toxic volatile compounds in air. Due to their low cost and compact size they can be placed in the areas exposed to pollution, outside the laboratory. Those advantages, on the other side, force the need for development of the reliable sensors data analysis procedures. One of the most important issues connected with electronic noses is the lack of stability of the gas...
-
Angle Tracking Observer for Filtering Rotor Position Estimates in Sensorless Electric Drives
PublicationSensorless electric drives use measurements of electrical quantities to estimate rotor position and speed. Measurement errors deteriorate the estimation accuracy, thus additional means are necessary to remove high-frequency components from estimated signals. This paper proposes to use an Angle Tracking Observer (ATO) for reducing noise in rotor position estimates, which is related to random errors in the measurements. A simplified,...
-
Mesoscopic impedance analysis of solid materials surface
PublicationSeveral techniques have been developed in order to characterize electrical properties of surfaces in micrometer/nanometer scale. Obtaining of the spatial distribution of sample resistance, capacitance or potential requires separate measurements performed in different scanning modes. On the other hand, analysis of the frequency response of investigated system enables determination of several physical quantities in single measurement...
-
Profesor Stanisław Trzetrzewiński – polski prekursor niepewności pomiaru
PublicationArtykuł ma na celu przybliżenie sylwetki Profesora Stanisława Trzetrzewińskiego, jako pierwszego kierownika Katedry Miernictwa Elektrycznego na Wydziale Elektrycznym Politechniki Gdańskiej, odpowiedzialnego za organizację Katedry po wojnie, dydaktyka, ale przede wszystkim wybitnego metrologa. Profesora Stanisława Trzetrzewińskiego można nazwać polskim prekursorem teorii niepewności pomiaru, co potwierdza wygłoszony w 1952 roku...
-
Corrosion monitoring by harmonic analysis in aqueous environments
PublicationThis paper presents tests concerning the rate of corrosion in non-alloy steel (type S235JR) in an aqueous environment, with an additive of sodium chloride by means of polarization resistance measurements and harmonic analysis. The tests have been carried out for steel samples exposed to the testing environment for six weeks, in order to obtain a constant rate of corrosion in the function of time. The measurements have aimed at...
-
Badania i analizy kolejowych konstrukcji odciążających typu mostowego
PublicationW pracy przedstawiono i omówiono wybrane modele obliczeniowe, wyniki analiz teoretycznych oraz badań trzech typów kolejowych konstrukcji odciążających typu mostowego. Zaprezentowano modele obliczeniowe oraz metodykę badań in situ tego typu konbstrukcji. Przedstawiono wnioski dotyczące zaawansowanych metod obliczeniowych rozszerzonych badań in situ w celu diagnozowania rzeczywistej pracy obiektów mostowych.