displaying 1000 best results Help
Search results for: PROBABILISTIC FAILURE
-
Comparative Study of the Mechanical Behaviour of Bitumen- and Cement-Dominated Mixtures with Reclaimed Asphalt
PublicationThe bitumen emulsion-based recycling is a commonly used maintenance treatment in the rehabilitation of low-and medium-volume roads in Europe. Nevertheless, the wide range of climatic conditions across the continent resulted in the variety of mixture concepts and the requirements being adopted for various local conditions. In this regard, the most commonly used parameter to distinguish between the main mixture concepts is bitumen...
-
Assessment of Thermal Stresses in Asphalt Mixtures at Low Temperatures Using the Tensile Creep Test and the Bending Beam Creep Test
PublicationThermal stresses are leading factors that influence low-temperature cracking behavior of asphalt pavements. During winter, when the temperature drops to significantly low values, tensile thermal stresses develop as a result of pavement contraction. Creep test methods can be suitable for the assessment of low-temperature properties of asphalt mixtures. To evaluate the influence of creep test methods on the obtained low-temperature...
-
Testing impedance analyzer with potentiostat using RC model with Si diode at 200 mV
Open Research DataThe dataset presents impedance spectrum non-linear RC model with diode presented in the figure below. This model was used as a test engine of the impedance analyzer with potentiostat described in the referenced paper. When changing the DC polarisation of the model the non-linear phenomena could be observed. Thanks to this, the model can be used as a...
-
Testing impedance analyzer with potentiostat using RC model with Si diode at 0 V
Open Research DataThe dataset presents impedance spectrum non-linear RC model with diode presented in the figure below. This model was used as a test engine of the impedance analyzer with potentiostat described in the referenced paper. When changing the DC polarisation of the model the non-linear phenomena could be observed. Thanks to this, the model can be used as a...
-
Testing impedance analyzer with potentiostat using RC model with Si diode at 600 mV
Open Research DataThe dataset presents impedance spectrum non-linear RC model with diode presented in the figure below. This model was used as a test engine of the impedance analyzer with potentiostat described in the referenced paper. When changing the DC polarisation of the model the non-linear phenomena could be observed. Thanks to this, the model can be used as a...
-
Testing impedance analyzer with potentiostat using RC model with Si diode at 400 mV
Open Research DataThe dataset presents impedance spectrum non-linear RC model with diode presented in the figure below. This model was used as a test engine of the impedance analyzer with potentiostat described in the referenced paper. When changing the DC polarisation of the model the non-linear phenomena could be observed. Thanks to this, the model can be used as a...
-
Development and performance analysis of a novel multiphase doubly-fed induction generator
PublicationThis paper presents the research into the design and performance analysis of a novel five-phase doubly-fed induction generator (DFIG). The designed DFIG is developed based on standard induction motor components and equipped with a five-phase rotor winding supplied from the five-phase inverter. This approach allows the machine to be both efficient and reliable due to the ability of the five-phase rotor winding to operate during...
-
Consideration of the safety of bungee jumping in relation to mechanical properties of the instalation based on a jump accident in Gdynia
PublicationThis paper considers a bungee jumping accident that took place in July 2019 in Gdynia, Poland. The authors conducted an investigation to determine the cause of the bungee rope failure. It was based on mechanical tests concerning the strength of the rope as well as the calculation of the force induced in the rope during the jump. Based on the theoretical and experimental results, the rope safety factor was estimated. It appeared...
-
The Reference Model of Tools Adaptation in the Perspective of Technological Agile Transformaton in IT Organizations
PublicationThe scientific aim of the presented paper is the analysis of agile transformation processes in IT organizations in technological perspective of such transformation. The phenomenon of agile transformation becomes a complex challenge for an IT organization, since it has not been analysed in detail so far. There is not any research on the readiness of IT organizations for the realization of agile transformation processes, and such...
-
Numerical investigations on early indicators of fracture in concrete at meso-scale.
PublicationFracture is a major reason of the global failure of concretes. The understanding of fracture is important to ensure the safety of structures and to optimize the material behaviour. In particular an early prediction possibility of fracture in concretes is of major importance. In this paper, concrete fracture under bending was numerically analysed using the Discrete Element Method (DEM). The real mesoscopic structure of a concrete...
-
Electrochemical cell impedance spectra at Eoc+100mV
Open Research DataThe dataset presents impedance spectrum of electrochemical cell filled with 3% NaCl solution presented in the figure below. This cell was used measured using Atlas-Sollich 0531 impedance analyser with built-in potentiostat. When changing the DC polarisation of the cell the non-linear phenomena could be observed. The impedance spectrum frequency range...
-
Electrochemical cell impedance spectra at Eoc+200mV
Open Research DataThe dataset presents impedance spectrum of electrochemical cell filled with 3% NaCl solution presented in the figure below. This cell was used measured using Atlas-Sollich 0531 impedance analyser with built-in potentiostat. When changing the DC polarisation of the cell the non-linear phenomena could be observed. The impedance spectrum frequency range...
-
Testing high impedance analyzer in the field on high-voltage line pylon cell 1 exposition 2
Open Research DataThe dataset presents impedance spectrum of anticorrosion coating on high-voltage line pylon presented in the figure below. This object was used to test high-impedance analyzer for diagnostic of anticorossion coatings (HIADAC) realized in the frame of Eureka project E!3174. The dataset contains comparative measurements with Atlas-Sollich ATLAS98HI analyser....
-
Testing high impedance analyzer in the field on high-voltage line pylon cell 1 exposition 1
Open Research DataThe dataset presents impedance spectrum of anticorrosion coating on high-voltage line pylon presented in the figure below. This object was used to test high-impedance analyzer for diagnostic of anticorossion coatings (HIADAC) realized in the frame of Eureka project E!3174. The dataset contains comparative measurements with Atlas-Sollich ATLAS98HI analyser....
-
Electrochemical cell impedance spectra at Eoc-100mV
Open Research DataThe dataset presents impedance spectrum of electrochemical cell filled with 3% NaCl solution presented in the figure below. This cell was used measured using Atlas-Sollich 0531 impedance analyser with built-in potentiostat. When changing the DC polarisation of the cell the non-linear phenomena could be observed. The impedance spectrum frequency range...
-
Electrochemical cell impedance spectra at Eoc
Open Research DataThe dataset presents impedance spectrum of electrochemical cell filled with 3% NaCl solution presented in the figure below. This cell was used measured using Atlas-Sollich 0531 impedance analyser with built-in potentiostat. When changing the DC polarisation of the cell the non-linear phenomena could be observed. The impedance spectrum frequency range...
-
Testing high impedance analyzer in the field on high-voltage line pylon cell 2 exposition 1
Open Research DataThe dataset presents impedance spectrum of anticorrosion coating on high-voltage line pylon presented in the figure below. This object was used to test high-impedance analyzer for diagnostic of anticorossion coatings (HIADAC) realized in the frame of Eureka project E!3174. The dataset contains comparative measurements with Atlas-Sollich ATLAS98HI analyser....
-
Electrochemical cell impedance spectra at Eoc-200mV
Open Research DataThe dataset presents impedance spectrum of electrochemical cell filled with 3% NaCl solution presented in the figure below. This cell was used measured using Atlas-Sollich 0531 impedance analyser with built-in potentiostat. When changing the DC polarisation of the cell the non-linear phenomena could be observed. The impedance spectrum frequency range...
-
Diagnostic Model of Crankshaft Seals
PublicationT he paper presents a research stand being a diagnostic model of radial lip seals used, among others, on crankshafts of piston combustion engines in order to identify the correctness of their operation. The possibility of determining the technical condition of lip seals on the basis of the proposed coefficient of correctness of operation has been described. T he basic features of seals influencing their correctness of...
-
Incorporating installation effects into the probability analysis of controlled modulus columns
PublicationThis technical report presents the probabilistic analysis which integrates the Monte Carlo simulation (MCS) with random field theory to model the load–displacement behavior of Controlled Modulus Columns (CMCs) in overconsolidated Poznań clay. Presented study focuses on the practical aspects of statistical analysis of geotechnical data, numerical model development, and results evaluation. Variability and spatial distribution of...
-
A framework for onboard assessment and monitoring of flooding risk due to open watertight doors for passenger ships
PublicationPost-accident safety of ships is governed by damage stability, affected by watertight subdivisions which limit accidental flooding. This is important for passenger ships with watertight doors (WTDs) often fitted in the bulkheads. Awareness of the ship flooding risk due to open WTDs and the conditions under which the associated risk level changes are prerequisites for proactive risk mitigation. Accident risk is often expressed as...
-
Safety integrity level verification for safety-related functions with security aspects
PublicationThe article is devoted some important issues of the functional safety analysis, in particular the safetyintegrity level (SIL) verification of safety functions to be implemented within the distributed controland protection systems with regard to cyber security aspects. The procedure for functional safety man-agement includes hazard identification, risk analysis and assessment, specification of overall safetyrequirements and definition...
-
Systems Engineering Requirements for Rotating Machines (PG-00060237)
e-Learning CoursesTurbiny wiatrowe, gazowe, mikroturbiny, silniki lotnicze, turbosprężarki i inne systemy mechaniczne to przykłady maszyn wirujących, które wymagają wysoko wykwalifikowanych inżynierów. Powinni oni zrozumieć złożoność procesów projektowania i produkcji, w tym wytwarzania przyrostowego, oraz konserwacji prognostycznej opartej na inżynierii cyfrowej dla bezawaryjnej pracy silnika. Wind, gas, micro turbines, aircraft engines, turbochargers,...
-
Voice Multilateration System
PublicationThis paper presents an innovative method of locating airplanes, which uses only voice communication between an air traffic controller and the pilot of an aircraft. The proposed method is described in detail along with its practical implementation in the form of a technology demonstrator (proof of concept), included in the voice communication system (VCS). A complete analysis of the performance of the developed method is presented,...
-
Numerical simulation of the influence of the selected factors on the performance of a concrete road barrier H2/W5/B
PublicationThis paper discuss the influence of selected factors on the performance of a concrete road barrier H2/W5/B. Modelling techniques of a concrete road safety system were briefly discussed. Comparison to the full scale crash test results has been shown. The concrete road safety barrier has been investigated for evaluation of the overall damage after collision under various initial conditions. The failure assessment criterion has been...
-
Mechanical Properties of a Dike Formed from a Soil-ash Composite
PublicationThe paper presents the research results on application of composite soils for dike construction. The composite soil is produced by mixing bottom ash (by-product of energetics) with dredged material (sand) taken from the mouth of The Vistula river. The optimum composite for dike core was chosen with respect to mechanical parameters: high internal friction angle, good compaction and reduced hydraulic conductivity. The test dike was...
-
Influence of an applied bearing system on behaviour of multi-span footbridge
PublicationThe cycle overpass in Gdynia is a box structure over 300 metres long, 10-span. It was opened for bicycle traffic in the second half of 2013. At the end of its construction, there was failure due to excessive horizontal displacement of the system. A number of bearings exceeded the range of permissible transverse shifts thus it was necessary to temporarily protect the spans from slipping. The FEM analysis of the original solution...
-
Analysis of Ceramic Elements with Ring-Crack Defects in Lubricated Rolling Contact
PublicationThe properties of ceramics, specifically low density, high hardness, high temperature capability and low coefficient of thermal expansion are of most interest to rolling element manufacturers. Surface ring cracks on lubricating rolling contact fatigue failure has been studied using numerical fracture analysis. Such cracks are very often found on ceramic bearing balls and decrease fatigue life rapidly. The numerical calculations...
-
Testing high impedance analyzer in the field on high-voltage line pylon cell 2 exposition 2
Open Research DataThe dataset presents impedance spectrum of anticorrosion coating on high-voltage line pylon presented in the figure below. This object was used to test high-impedance analyzer for diagnostic of anticorossion coatings (HIADAC) realized in the frame of Eureka project E!3174. The dataset contains comparative measurements with Atlas-Sollich ATLAS98HI analyser....
-
The correlation of fractal dimension to fracture surface slope for fatigue crack initiation analysis under bending-torsion loading in high-strength steels
PublicationIn this study, the fractal dimension of fatigue fracture surfaces is investigated in order to find an alternative failure loading indicator. Some of many metrological factors are generalized by reducing the fracture surface structure to one factor and develop an entire fracture surface procedure by analyzing the impact of surface slope and calculation resolution. Three notched geometries are studied under cyclic bending-torsion:...
-
Meso‐scale analyses of size effect in brittle materials using DEM
PublicationThe paper describes numerical meso-scale results of a size effect on strength, brittleness and fracture in brittle materials like concrete. The discrete element method (DEM) was used to simulate the size effect during quasi-static splitting tension with the experimental-based meso-structure. The two-dimensional (2D) calculations were carried out on concrete cylindrical specimens with two diameters wherein two different failure...
-
Checkpointing of Parallel MPI Applications using MPI One-sided API with Support for Byte-addressable Non-volatile RAM
PublicationThe increasing size of computational clusters results in an increasing probability of failures, which in turn requires application checkpointing in order to survive those failures. Traditional checkpointing requires data to be copied from application memory into persistent storage medium, which increases application execution time as it is usually done in a separate step. In this paper we propose to use emerging byte-addressable...
-
A theoretical framework for understanding trust and distrust in internet voting
PublicationEach and every case of success and failure in the implementation of internet voting is permeated by a common element: the concept of trust. Several researchers highlighted the relevance of creating trust for the successful implementation of technology [15] and, in particular, of internet voting [13]. But the concept itself is complex and challenging to define, for one fundamental reason: it is a concept of everyday social use...
-
Optimization model of agile team’s cohesion
PublicationTeam’s cohesion is one of the most important factors of IT project execution effectiveness. Optimization of team’s cohesion gives the possibility of reducing the risk of project failure. It also allows to increase the teamwork efficiency and thus optimize time of tasks execution, increase the guarantee of maintaining the scope of the project and the chance of achieving a given level of products quality. This article presents determination...
-
Experimental Tests Of Sandwich Beams In The Design Process Of GFRP Shell Footbridge Structure
PublicationThe paper includes selected aspects of the study to elaborate architectural, material and construction design of pedestrian footbridge spans made of composite materials. The considered footbridge is a sandwich-type shell structure. The cooperation of PET foam core with outer lining surfaces is crucial for its load bearing capacity. The paper is aimed to experimental investigation of sandwich beams subjected to bending loading....
-
ECG-based prediction of ventricular fibrillation by means of the PCA
PublicationA Sudden Cardiac Death (SCD) is a death resulting from cardiac failure with no significant symptoms earlier than one hour before occurrence. It is the cause of for approximately 400000 deaths per year in United States and millions of deaths worldwide. The proposed system, including two-stage algorithm and wearable diagnostic device allows for SCD risk estimation and continuous monitoring of high risk patients. A single channel...
-
Crack Mouth Opening Displacement for EH36 Shipbuilding Steel Measurements
PublicationThe dataset titled EH36 steel for shipbuilding (plate thicnkness 50mm) - CMOD - force record, a0/W = 0.6 contains CMOD (Crack Mouth Opening Displacement) - Force record which is the base for evaluation of fracture toughness of structural steel. Bend specimens witch Bx2B section (B= 50mm), and relative initial crack length a0 / W = 0.60 were used. The test was carried out at ambient temperature in accordance to ISO 12135 standard....
-
Smart heating system for home extending utilization of renewable energy sources
PublicationIn the paper a modern approach to smart home heating is presented. Proposed solution utilizes at least two low-polluting energy source technologies. The main idea is to connect well known ecological energy sources in a way that they can support each other and minimize risks of failure when using single system or even both of them but managed in separate way. Considered energy technologies, used separatelly, have disadvan-tages,...
-
Modal analysis of cylindrical steel tanks
PublicationCylindrical steel tanks are very popular structures used for storage of products of chemical and petroleum industries. Their safety and reliability is crucial because any failure could have serious consequences. The aim of present paper is to show the results of the first phase of investigation of seismic behaviour such structures. Modal analysis using Finite Element Method (FEM) for three models of real tanks used in Poland has...
-
Numerical analysis of crack propagation in silicone nitride
PublicationThe properties of ceramics, specifically low density, high hardness, high temperature capability and low coefficient of thermal expansion are of most interest to rolling element manufacturers. The influence of ring crack size on rolling contact fatigue failure has been studied using numerical fracture analysis. Such cracks are very often found on ceramic bearing balls and decrease fatigue life rapidly. The numerical calculation...
-
Defending against Fake VIP in Scant-Transparency Information Systems with QoS Differentiation
PublicationIn client-server information systems with quality of service (QoS) differentiation, Client may deplete Server’s resources by demanding unduly high QoS level. Such QoS abuse has eluded systematic treatment; known defenses using Client authorization, payments, or service request inspection prior to QoS assignment, are heuristic and environment-specific. We offer a game-theoretic approach on the premise that a service request is occasionally...
-
The Effect of the Selection of Three-Dimensional Random Numerical Soil Models on Strip Foundation Settlements
PublicationThis paper delivers a probabilistic attempt to prove that the selection of a random three-dimensional finite element (FE) model of a subsoil affects the computed settlements. Parametricanalysis of a random soil block is conducted, assuming a variable subsoil Young’s modulus inparticular finite elements. The modulus is represented by a random field or different-sized setsof random variables; in both cases, the same truncated...
-
Double-Blind Reputation vs. Intelligent Fake VIP Attacks in Cloud-Assisted Interactions
PublicationWe consider a generic model of Client-Server interactions in the presence of Sender and Relay, conceptual agents acting on behalf of Client and Server, respectively, and modeling cloud service providers in the envisaged "QoS as a Service paradigm". Client generates objects which Sender tags with demanded QoS level, whereas Relay assigns the QoS level to be provided at Server. To verify an object's right to a QoS level, Relay detects...
-
Comparative wear test of journal sliding bearings with sintered bronze and Babbitt alloy bushes lubricated by environmentally acceptable/adapted lubricants (EAL)
PublicationA growing awareness of the negative effects of mineral oils on the natural environment has resulted in the introduction of new regulations related to environmental protection. One of these regulations requires the use of environmentally acceptable/adapted lubricants (EAL) to lubricate marine main shaft bearings, in place of the mineral lubricating oils that have been used for decades. Classification Societies, which supervise...
-
Testing HIADAC high impedance analyzer in Trento University laboratory on Baunier's RC model using 2 wire probe
Open Research DataThe dataset presents impedance spectrum of Baunier's RC model. This object was used to test high-impedance analyzer for diagnostic of anticorossion coatings (HIADAC) realized in the frame of Eureka project E!3174. The impedance spectrum frequency range (1 mHz – 100 kHz) was selected in order to test the whole measureement range of the analyzer. In...
-
Mechanical compatibility of implants used in hernia repair with abdominal wall
PublicationThe paper deals with a membrane model of a synthetic surgical mesh for treatment of abdominal hernia. The authors analyse the compatibility of two implant types with the human wall: Dualmesh Gore and Proceed. The finite element method is applied to simulate tjhe behavior of the proposed model. Due fact that recurrences are usually caused by connection failure, this study is focused on reaction forces in supports representing the...
-
Experimental determination of dynamic properties of cylindrical steel tank model filled with liquid
PublicationIn technical branches, such as chemical or petroleum industries, cylindrical steel tanks are essential structures used for storage of liquid products. Any failure might have disastrous consequences, therefore their safety and reliability is essential. The aim of the present paper is to show the results of the experimental study which has been conducted on a scaled model of a real tank used in Poland. The investigation was carried...
-
Reliability Analysis of Sea Cliff Slope Stability by Point Estimate Method
PublicationThe paper presents a reliability analysis of a sea cliff slope. The cliff, located in Jastrzębia Góra, is characterised by a complicated geological structure. Although currently stable, it is in fact close to the limit state. The objective of this paper is to present the point estimate method (PEM) of determining the mean value and standard deviation of the safety factor of the slope. Assuming its normal distribution, these statistical...
-
Crack Mouth Opening Displacement for EH36 Shipbuilding Steel Measurements Dataset
PublicationThe dataset titled EH36 steel for shipbuilding (plate thickness 50 mm) – CMOD – force record, a0/W=0.6 contains a CMOD (Crack Mouth Opening Displacement) – Force record which is the base for evaluation of the fracture toughness of structural steel. Bend specimens with a Bx2B section (B = 50 mm), and relative initial crack length a0/W=0.60 were used. The test was carried out at ambient temperature in accordance with the ISO 12135...
-
Effect of bitumen characteristics obtained according to EN and Superpave specifications on asphalt mixture performance in low-temperature laboratory tests
PublicationThe paper aims to identify those characteristics of bitumen which have the greatest impact on asphalt mixture low-temperature performance. It was observed that stiffness and m-value of bitumen from BBR test were moderately related to stiffness and m-value of asphalt mixture obtained from 3 PB test. Simultaneously those rheological properties significantly impact on cryogenic stresses induced during TSRST test. The multiple regression...