displaying 1000 best results Help
Search results for: oils encapsulation
-
Measurement of temperature-dependent viscosity and thermal conductivity of alumina and titania thermal oil nanofluids
PublicationThe results of simultaneous measurements of dynamic viscosity, thermal conductivity, electrical conductivity and pH of two nanofluids, i.e. thermal oil/Al2O3 and thermal oil/TiO2 are presented. Thermal oil was selected as a base liquid because of possible application in ORC systems as an intermediate heating agent. Nanoparticles were tested at the concentration of 0.1%, 1% and 5% by weight within temperature range from 20°C to...
-
Role of Litsea cubeba Essential Oil in Agricultural Products Safety: Antioxidant and Antimicrobial Applications
Publication -
Antimicrobial and antioxidant activities of Cinnamomum cassia essential oil and its application in food preservation
Publication -
Losses and power balance in hydraulic satellite motor supplied with oil and HFA-E emulsion
PublicationMineral oil and HFA-E emulsion are liquids which differ in viscosity, density and lubricant properties. Therefore, supplying hydraulic satellite motor with these liquids, differences between quantity of hydraulic, volumetric and mechanical losses are observed. These losses influence efficiency of conversion of hydraulic energy into mechanical energy and thereby power balance of motor. The research of satellite motor has been conducted...
-
The oil film parameters of the wankel engine apex seal in aspects of durability of mating elements
PublicationThe Wankel engine is one of only few alternatives to the reciprocating engines. The advantages such as good value of maximum engine power to its mass ratio are still present and can have great sense in selected fields of application, for example General Aviation. Nevertheless the disadvantages of the Wankel engine design have never lost its importance and still pose an obstacle to wider use of the Wankel engine. One of the main...
-
Extraction, Optimization, and Characterization of Neem Seed Oil via Box-Behnken Design Approach
Publication -
The Effect of a Gear Oil on Abrasion, Scuffing, and Pitting of the DLC-Coated 18CrNiMo7-6 Steel
Publication -
Load effect impact on the exploitation of concrete machine foundations used in the gas and oil industry
PublicationMachine foundations is a critical topic in the gas and oil industry, which design and exploitation require extensive technical knowledge. Machine foundations are the constructions which are intended for mounting on it a specific type of machine. The foundation has to transfer dynamic and static load from machine to the ground. The primary difference between machine foundations and building foundations is that the machine foundations...
-
The influence of water and mineral oil on volumetric losses in the displacement pump for offshore and marine applications
PublicationIn this paper volumetric losses in a positive displacement pump supplied with water and mineral oil are described and compared. The experimental tests were conducted using a prototype of a satellite pump (with a non-circular tooth working mechanism). In this paper the sources of volumetric losses in this pump are characterised. On this basis, a mathematical model of these losses has been presented. The results of the calculation...
-
Superhydrophobic and superoleophilic melamine sponges impregnated with deep eutectic solvents for oil spill cleanup
PublicationThe extensive extraction of oil from the bottom of seas and oceans and its transportation by tankers increase the risk of potential environmental disasters associated with hydrocarbon fractions entering water reservoirs. Therefore, this paper presents the preparation of a simple impregnation of a melamine sponge with deep eutectic solvents (DES), which can be obtained from natural sources, including coconut oil, palm kernel oil,...
-
Experimental comparison of the transition speed of a hydrodynamic journal bearing lubricated with oil and magnetorheological fluid
PublicationA journal bearing test bench is used to find the transition speed between the hydrodynamic and mixed lubrication regimes for a modified magnetorheological (MR) fluid. It is shown that the transition speed of the bearing can be reduced by applying a local magnetic field near minimum film when it is lubricated with the MR fluid, and that this will only marginally increase friction. The lubricating performance of the MR fluid is compared...
-
Waste management in the mining industry of metals ores, coal, oil and natural gas - A review
PublicationWaste generated due to mining activity poses a serious issue due to the large amounts generated, even up to 65 billion tons per year, and is often associated with the risk posed by its storage and environmental management. This work aims to review waste management in the mining industry of metals ores, coal, oil and natural gas. It includes an analysis and discussion on the possibilities for reuse of certain types of wastes generated...
-
Compatibility of Crude Oil Blends─Processing Issues Related to Asphaltene Precipitation, Methods of Instability Prediction─A Review
PublicationProcessing crude oil of variable composition, especially due to the need to process crude oil blends obtained from various sources, presents a tremendous process challenge. This is mainly due to the destabilization of the colloidal system manifested mostly by the precipitation of the asphaltene fraction. The precipitation of asphaltenes from crude oil is a serious problem during extraction, transport, and processing. In the latter...
-
The effect of high molecular weight bio-based diamine derivative of dimerized fatty acids obtained from vegetable oils on the structure, morphology and selected properties of poly(ether-urethane-urea)s
PublicationIn this work, the effect of the high molecular weight bio-based diamine on the chemical structure and selected properties of poly(ether-urethane-urea)s has been investigated. The ether-urethane prepolymer was cured using 1,4-butanediol and/or bio-based diamine. Mentioned chain extenders were used separately or in the mixture, and their different molecular weight and chemical structure resulted in obtaining materials with diversified...
-
Complementary Use of Multi-dimensional Gas Chromatography and Proton Transfer Reaction Mass Spectrometry for Identification of Rapeseed Oil Quality Indicators
PublicationThe change of concentration of various volatiles generated during frying may be an indicator of oil quality. Chemical compounds such as aldehydes, ketones, alcohols and carboxyl acids are the products of oxidation during thermal degradation of edible oils. Shown in this work is a complementary use of GC×GC-TOFMS and PTR-MS for the detection and determination of quality indicators of rapeseed oil. The former technique was used for...
-
Mohammad Malikan dr inż.
PeopleMohammad Malikan studied Ph.D. at the Department of Mechanics of Materials and Structures at the Gdańsk University of Technology. He was the first person who graduated in the new form of the doctoral education system of Poland (Doctoral School). He has worked as a mechanical engineer and designer for several years in CAD/CAE fields in various industries, such as feed production lines, machinery, elevator, oil, etc. His main research...
-
RAPESEED PELLET - A BYPRODUCT OF BIODIESEL PRODUCTION - AS AN EXCELLENT RENEWABLE ENERGY SOURCE
PublicationVegetable oils are renewable feedstock currently being used for production of biofuels from sustainable biomass resources. The existing technology for producing diesel fuel from plant oils, such as rapeseed, soybean, canola and palm oil are largely centered on transesterification of oils with methanol to produce fatty acid methyl esters (FAME) or biodiesel. Rapeseed pellet - crushed seed residue from oil extraction is a byproduct...
-
Chemical Characteristics and Thermal Oxidative Stability of Novel Cold-Pressed Oil Blends: GC, LF NMR, and DSC Studies
PublicationPlant oils contain a high content of unsaturated fatty acids. Studies of food products have revealed a considerable disproportion in the ratio of ω6 to ω3. This article presents information on the healthful qualities of eight new oil blends that contain a beneficial proportion of ω6 to ω3 fatty acids (5:1), as well as their degradation during heating at 170 and 200 °C. The fatty acid profile was analyzed by gas chromatography (GC),...
-
Journal of Essential Oil Bearing Plants
Journals -
JOURNAL OF THE AMERICAN OIL CHEMISTS SOCIETY
Journals -
Tensile strength test of PE foils modified with zinc oxide and zinc salts
Open Research DataThis dataset contains the results of PE foils mechanical tests, in which the material was evaluated for strength and extensibility at the moment of breaking and based on the same tests preceded by material fatigue in 50 stretching cycles. The principle of the method is to stretch the test sample placed in the clamps of the stretching apparatus at a...
-
Feasibility Study GaN Transistors Application in the Novel Split-Coils Inductive Power Transfer System with T-Type Inverter
PublicationA promising solution for inductive power transfer and wireless charging is presented on the basis of a single-phase three-level T-type Neutral Point Clamped GaN-based inverter with two coupled transmitting coils. The article focuses on the feasibility study of GaN transistor application in the wireless power transfer system based on the T-type inverter on the primary side. An analysis of power losses in the main components of the...
-
Interplay between Selected Chemical and Biochemical Soil Properties in the Humus Horizons of Grassland Soils with Low Water Table Depth
Publication -
Influence of Installation Effects on Pile Bearing Capacity in Cohesive Soils – Large Deformation Analysis Via Finite Element Method
PublicationIn this paper, the whole process of pile construction and performance during loading is modelled via large deformation finite element methods such as Coupled Eulerian Lagrangian (CEL) and Updated Lagrangian (UL). Numerical study consists of installation process, consolidation phase and following pile static load test (SLT). The Poznań site is chosen as the reference location for the numerical analysis, where series of pile SLTs...
-
Geochemical fractionation and spectroscopic fingerprinting for evaluation of the environmental transformation of potentially toxic metal(oid)s in surface–subsurface soils
Publication -
Opracowanie procedury oznaczania lotnych produktów utleniania olejów roślinnychtechniką statycznej analizy fazy nadpowierzchniowej = The development of a new procedure for determination of volatile oxidation products in edible oils with the use of static headspace analysis
PublicationW publikacji przedstawiono dobór optymalnych parametrów w celu opracowania nowej metody diagnozowania jakości olejów poprzez oznaczenie lotnych związków będących produktami reakcji utleniania olejów. Próbki rafinowanych olejów roślinnych przed analizą poddano procesowi przyspieszonego utleniania, stosując naświetlanie promieniowaniem ultrafioletowym (12 W, 254 nm). Jako technikę ekstrakcji lotnej frakcji próbki zastosowano statyczną...
-
Preliminary Study on the Antibacterial Activity of Essential Oils Alone and in Combination with Gentamicin Against Extended-Spectrum β-Lactamase-Producing and New Delhi Metallo-β-Lactamase-1-Producing Klebsiella pneumoniae Isolates
Publication -
Determination of paraffin oil mist penetration at high flow rates through air-purifying respirators
Publication -
On possible lowering fuel oil consumption by differentiating loads on ship diesel engines running in parrallel.
PublicationPodano możliwości zmniejszenia zużycia paliwa przez silniki okrętowe pracujące równolegle dzieki różnicowaniu ich obciążeń eksploatacyjnych. Zaprezentowano podstawy teoretyczne oraz sposób postępowania przy pomiarach zużycia paliwa w czasie rzeczywistym.
-
Mathematical model defining volumetric losses of hydraulic oil compression in a variable capacity displacement pump
PublicationThe objective of the work is to develop the capability of evaluating the volumetric losses of hydraulic oil compression in the working chambers of high pressure variable capacity displacement pump. Volumetric losses of oil compression must be determined as functions of the same parameters, which the volumetric losses due to leakage, resulting from the quality of design solution of the pump, are evaluated as dependent on and also...
-
Corrosion-erosion damage of heat exchanger tubes by desalted crude oil flowing at shell side.
PublicationRurki wymiennika zostały uszkodzone lokalnie przez odsoloną ropę naftową przepływającą pod ciśnieniem 2,6 MPa i w temperaturze 385-395K. Większość powierzchni rurek nie była uszkodzona i była pokryta osadem związków organicznych i nieorganicznych, zabezpieczającym przed uszkodzeniami. Badania wykluczyły możliwość występowania intensywnej korozji elektrochemicznej na powierzchniach rurek pozbawionych osadu. Przyczyną perforacji...
-
Eco-friendly modification of bitumen: The effects of rubber wastes and castor oil on the microstructure, processability and properties
PublicationThe bitumen industry in the European Union is facing several difficulties, including rising demand, unstable oil supply, rising prices for synthetic polymer modifiers, and a focus on lowering carbon footprint. Bitumen modification with crumb rubber (CR) is one of the most promising solution to these challenges. However, CR-modified bitumen have poor processability and low storage stability. To overcome these flaws we are introducing...
-
Underwater Electrochemical Offshore Tests of a Paint Coating Applied in Water on the Legs of an Oil Production Platform
PublicationThis paper presents the methodology developed for underwater measurements using electrochemical impedance spectroscopy (EIS) technique, aimed at determining the resistance of an epoxy coating applied in seawater to the legs of an oil production platform. Performing such underwater tests in an offshore environment was technically challenging. The results of measurements obtained on the platform were confronted with comparative results...
-
Corrosion-erosion damage of heat exchanger tubes by desalted crude oil flowing at shell side
Publication -
Application of an extended DLVO theory for the calculation of the interactions between emulsified oil droplets in alcohol solutions
Publication -
Fatty Acids Composition of Mustard Oil from Two Cultivars and Physico-chemical Characteristics of the Seeds
Publication -
The influence of type of dispersed phase on rolling contact fatigue of lubricating greases on mineral base oil
Publication -
The ILs-assisted solvothermal synthesis of TiO2 spheres: the effect of ionic liquids on morphology and photoactivity of TiO2
PublicationEffect of the ionic liquid (IL) structure (chain length in the imidazolium cation) on morphology and photoactivity of TiO2 particles has been systematically investigated. The TiO2 microspheres have been successfully synthesized via facile solvothermal method assisted by ionic liquids, such as 1-butyl-3-methylimidazolium chloride [BMIM][Cl] and 1-decyl-3-methylimidazolium chloride [DMIM][Cl] using tetra-tert-butyl orthotitanate...
-
Oil spill response planning tool for estimating the recovery capability of mechanical skimming systems potential
Publication -
An efficient method of Yarrowia lipolytica immobilization using oil- and emulsion-modified bacterial cellulose carriers
Publication -
A probabilistic model estimating oil spill clean-up costs – A case study for the Gulf of Finland
Publication -
A probabilistic model for accidental cargo oil outflow from product tankers in a ship–ship collision
Publication -
Chemical Composition, In Vitro and In Situ Antimicrobial and Antibiofilm Activities of Syzygium aromaticum (Clove) Essential Oil
Publication -
Plant Extracts Containing Saponins Affects the Stability and Biological Activity of Hempseed Oil Emulsion System
Publication -
The conception of uncertainty analysis of reliability assessment of the MC type diesel engine lubricating oil system
PublicationOmówiono elementy składające się na niepewność oszacowania niezawodności instalacji oleju smarowego dla silników typu MC. Przedstawiono, posługując się przykładem obliczeniowym, koncepcję analizy niepewności oceny rozpatrywanej instalacji. Ponadto zaproponowano sposób interpretacji otrzymanego wyniku, obarczonego dużą niepewnością, przy użyciu liczb rozmytych.
-
Air bubble and oil droplet interactions in centrifugal fields during air-sparged hydrocyclone flotation
PublicationWzajemne oddziaływania pęcherzyka powietrza i kropli oleju w polu siły odśrodkowej były rozpatrywane w odniesieniu do warunków procesowych obecnych podczas flotacji za pomocą hydrocyklonu. Efektywności zetknięcia się kropli oleju z pęcherzykami powietrza zostały zidentyfikowane jako znacząco mniejsze w porównaniu do efektywności zetknięcia się cząstek minerałów. Wyznaczono czasy zderzenia i styku ślizgowego. Chociaż przyczepność...
-
Synergisms and antagonisms between MoS2 nanotubes and representative oil additives under various contact conditions
Publication -
Effect of crystalline emulsifier composition on structural transformations of water-in-oil emulsions: Emulsification and quiescent conditions
Publication -
Mineral oil-based hydrostatic drives as the basic drive systems in the construction of offshore eqiupment projects
PublicationThe aim of this article is to present the components used in the production of mineral oil-based hydrostatic drives as the basic drive systems for the offshore industry. The article contains de-scriptions of the components of the said systems, with the description of their suitability for mi-neral oil operation and offshore applications.
-
Ground tire rubber thermo-mechanically devulcanized in the presence of waste engine oil as asphalt modifier
PublicationCross-linked elastomers network is main limitation for industrial usage of ground tire rubber (GTR) as asphalts’ and road pavements modifier. GTR was thermo-mechanically devulcanized via extrusion in the presence of waste engine oil (WEO) at temperature ranges from 150 to 280 °C. Combined impact of WEO content and extruder barrel temperature on the change of cross-linked structure of degraded GTR (DTGR) was investigated through...