Filters
total: 3829
displaying 1000 best results Help
Search results for: SUROWCE
-
Production and Properties of the Porous Layer Obtained by the Electrochemical Method on the Surface of Austenitic Steel
Publication: The growing demand for implants has seen increasing interest in the introduction of new technologies and surface modification methods of metal biomaterials. This research aimed to produce and characterize a porous layer grown on austenitic stainless steel 316L, obtained via the anodization process near the micro-arc oxidation, i.e., low voltage micro-arc oxidation (LVMAO). The discussed layer significantly influences the properties...
-
Effectiveness of a dual surface modification of metallic interconnects for application in energy conversion devices
PublicationA dual surface modification of an SOFC metallic interconnect with a Gd2O3 layer and an MnCo2O4 coating was evaluated. The tested samples were oxidized for 7000 h in air at 1073 K. Oxidation products were characterized using XRD, SEM-EDS, and confocal Raman imaging, and ASR was measured. The effect of gadolinium segregation at grain boundaries in Cr2O3 was evaluated using S/TEM-EDS. Area specific-resistance was measured and fuel...
-
Curved Surface Minijet Impingement Phenomena Analysed with ζ-f Turbulence Model
PublicationThe jet impingement phenomenon plays an important role among the heat transfer intensification methods. Very often its application and analyses refer to simple flat surfaces, while there is a lack of information in the literature for cases addressing curved surfaces. In the present work, the single jet impingement on the non-flat (concave and convex) surface is studied for a wide range of geometries, which originate from the mini-jet...
-
Effect of surface on the flexomagnetic response of ferroic composite nanostructures; nonlinear bending analysis
PublicationOur analysis incorporates the geometrically nonlinear bending of the Euler-Bernoulli ferromagnetic nanobeam accounting for a size-dependent model through assuming surface effects. In the framework of the flexomagnetic phenomenon, the large deflections are investigated referring to von-Kármán nonlinearity. Employing the nonlocal effects of stress coupled to the gradient of strain generates a scale-dependent Hookean stress-strain...
-
Preliminary Results of a System-theoretic Assessment of Maritime Autonomous Surface Ships' Safety
PublicationWhile a system‐theoretic approach to the safety analysis of innovative socio‐technical systems gains a growing acceptance among academia, safety issues of Maritime Autonomous Surface Ships (MASS) remain largely unexplored. Therefore, we applied a System‐Theoretic Process Analysis to develop and analyze a preliminary model of the unmanned shipping system in order to elaborate safety recommendations for...
-
Microstructure and mechanical properties of laser surface-treated Ti13nb13zr alloy with MWCNTs coatings
PublicationLaser surface modification of titanium alloys is one of the main methods of improving the properties of titanium alloys used in implantology. This study investigates the microstructural morphology of a laser-modified surface layer on a Ti13Nb13Zr alloy with and without a carbon nanotube coating deposited by electrophoretic deposition. Laser modification was performed for samples with and without carbon nanotube coating for two...
-
Trace elements content of surface peat deposits in the Solovetsky Islands (White Sea)
PublicationPeatlands form environmental archives of trace element deposition. In this regard they are particularly valuable for areas such as the Arctic, where regular pollution monitoring is either impossible or extremely costly. The aim of this study was to assess pollution in the Solovetsky Islands (65° 05' N, 35° 53' E) by examining the spatial variability in trace element content of the uppermost layer of peat, immediately below the...
-
Application of surface active amino acid ionic liquids as phase-transfer catalyst
PublicationFive structurally related morpholinium derived ionic liquids containing N-acetyl-glycinate anion were synthesized and their thermal stability, surface properties and activity as phase transfer catalysts investigated. The thermal properties were studied by differential scanning calorimetry, while the adsorption at the air/water interface and micellization behavior was analyzed by surface tension measurements, conductometry and isothermal...
-
Analysis of the Ways to Identify Rail Running Surface Defects by Means of Vibration Signals
PublicationTh e article discusses a preliminary concept of a method enabling the identifi cation of chosen rail running surface defects, such as squats, spalling, and running surface defects, by analysing the parameters of vibration signals. It features a description of the methodology of the conducted tests, the scope thereof, and the selection of the measurement points with specifi c defect types. Th e article covers selected results of...
-
Reliability-Based Stability Analysis of a Baltic Cliff by the Combined Response Surface Method
PublicationA simple, straightforward computational procedure was proposed, incorporating the Response Surface Method (RSM) linked with the standard Monte Carlo (MC) simulation method and the Point Estimate Method (PEM). PEM samples make it possible to analyse the sensitivity of the cliff’s stability to variation in subsoil parameters and to reduce the number of random variables of the problem. The proposed methods were tested in two cases:...
-
On Effective Bending Stiffness of a Laminate Nanoplate Considering Steigmann–Ogden Surface Elasticity
PublicationAs at the nanoscale the surface-to-volume ratio may be comparable with any characteristic length, while the material properties may essentially depend on surface/interface energy properties. In order to get effective material properties at the nanoscale, one can use various generalized models of continuum. In particular, within the framework of continuum mechanics, the surface elasticity is applied to the modelling of surface-related...
-
Mechanical and Corrosion Properties of Laser Surface-Treated Ti13Nb13Zr Alloy with MWCNTs Coatings
Publication: Titanium and its alloys is the main group of materials used in prosthetics and implantology. Despite their popularity and many advantages associated with their biocompatibility, these materials have a few significant disadvantages. These include low biologic activity—which reduces the growth of fibrous tissue and allows loosening of the prosthesis—the possibility of metallosis and related inflammation or other allergic reactions,...
-
On weak solutions of boundary value problems within the surface elasticity of Nth order
PublicationA study of existence and uniqueness of weak solutions to boundary value problems describing an elastic body with weakly nonlocal surface elasticity is presented. The chosen model incorporates the surface strain energy as a quadratic function of the surface strain tensor and the surface deformation gradients up to Nth order. The virtual work principle, extended for higher‐order strain gradient media, serves as a basis for defining...
-
Capacity of Surface Production of Band Sawing in Manufacture of Oak Floor Upper Layers
PublicationThin lamellae, corresponding to the layer components of structural glued members, i.e., 2-ply or 3-ply glued flooring, can be manufactured in re-sawing operations of kiln-dried wood blocks or in wet technologies, which currently seem to be more common because of the shorter drying time. The re-sawing process in wet technology is conducted on dedicated thin-cutting band sawing machines with stellite-tipped band saws. The goal of...
-
Influence of Surface-Modified Montmorillonite Clays on the Properties of Elastomeric Thin Layer Nanocomposites
PublicationIn recent years, polyurethane nanocomposites have attracted more attention due to the massive demand for materials with increasingly exceptional mechanical, optical, electrical, and thermal properties. As nanofillers have a high surface area, the interaction between the nanofiller and the polymer matrix is an essential issue for these materials. The main aim of this study is to validate the impact of the montmorillonite nanofiller...
-
Measurements and calculations of the width of the fracture process zones on the surface of notched concrete beams
PublicationArtykuł omawia wyniki pomiaru i analizy numerycznej szerokości strefy pękania w belkach betonowych z nacięciem. Do pomiarów zastosowano metodę DIC. Do symulacji zastosowano model sprężysto - plastyczny i model z degradacją sztywności. Oba modele zostały rozszerzone o nielokalne osłabienie. Wyniki symulacji porównano z doświadczeniami.
-
Biopaliwa z rzepaku. Przygotowanie surowca do otrzymywania biodiesla w warunkach gospodarstwa rolnego oraz pilotowe metanolizy
PublicationScharakteryzowano olej rzepakowy jako surowiec do produkcji biodiesla i opisano etapy procesu transestryfikacji. Oceniono metody wydobywania oleju rzepakowego poprzez tłoczenie w warunkach gospodarstwa rolnego i scharakteryzowano oleje pod względem przydatności do reakcji metanolizy (zawartość fosforu, LK, LOO, skład kwasów tłuszczowych). Przeprowadzono wstępne, laboratoryjne reakcje transestryfikacji i na ich podstawie wytypowano...
-
Surface EMG-based signal acquisition for decoding hand movements
Open Research DataBiosignal processing plays a crucial role in modern hand prosthetics. The challenge is to restore functionality of a lost limb based on the signals acquired from the surface of the stump. The number of sensors (emg channels) used for signal acquisition influence the quality of a prosthetic hand. Modern algorithms (including neural networks) can significantly...
-
Partial PLA composite surface activation by femtosecond laser ablation
Open Research DataThe dataset contains the studies on electrochemical activity of PLA composite (commercially available CB-PLA Protopasta), which was 3D printed in a form of 1x1cm electrodes. The electrodes were submitted to femtosecond laser ablation, etching a certain % of the electrochemically-exposed electrode size. The % value is in the name of each file. The goal...
-
Monthly mean concentration of chlorophyll a on the sea surface of the Baltic Sea
Open Research DataMonthly mean surface concentration of chlorophyll a in the years 2003-2022 calculated on the basis of data from the SatBaltic System (https://satbaltyk.iopan.gda.pl/). Maps of monthly average values with a resolution of 1 km were derived from daily satellite data from the Moderate Resolution Imaging Spectroradiometer (MODIS). Gaps in satellite images...
-
Partial PLA composite surface activation by femtosecond laser ablation
Open Research DataThe dataset contains the studies on electrochemical activity of PLA composite (commercially available CB-PLA Protopasta), which was 3D printed in a form of 1x1cm electrodes. The electrodes were submitted to femtosecond laser ablation operating with different parameters. These were: gas atmosphere (He or air, data in different subfolders), the percentage...
-
The surface of a fragment of the structure of an integrated circuit in the semi-contact mode.
Open Research DataThe surface of a fragment of the structure of an integrated circuit. Topographic measurements in the semi-contact mode. NTEGRA Prima (NT-MDT) device. NSG 01 probe.
-
Monthly mean sea surface temperature (SST) of the Baltic Sea
Open Research DataMonthly mean sea surface temperature (SST) from 2001 to 2022 calculated from data from the SatBaltic System (https://satbaltyk.iopan.gda.pl/). The spatial resolution of the maps is 1 km. The calculation of monthly mean values at each pixel was based on four SST maps on each day of the month. The primary source of SST information was satellite data collected...
-
Temperature influence on tyre/road noise on poroelastic road surface based on laboratory measurements
PublicationThe temperature effect on measured tyre/road noise is very important phenomena as it may lead to significant errors in measurement results due to substantial influence of this parameter on the obtained values. It depends mainly on the particular tyre-road combination. It is different for dense and porous as well as for bituminous and cement concrete pavements. It differs also depending on tested tyre. The correction procedure for...
-
Computing methods for fast and precise body surface area estimation of selected body parts
PublicationCurrently used body surface area (BSA) formulas give satisfactory results only for individuals with typical physique, while for elderly, obese or anorectic people accurate results cannot be expected. Particularly noteworthy are the results for individuals with severe obesity (body-mass index greater than 35 kg/m2), for which BSA estimation errors reached 80%. The main goal of our study is the development of precise BSA models for...
-
Surface irregularities as a complex signal of tool representation together with uneven displacement in respect to the workpiece
PublicationIn a dynamic machining process, distortion in surface irregularity is a very complex phenomenon. Surface irregularities form a periodic representation of the tool profile with various kinds of disturbance in a broad range of changes in the height and length of the profile. To discern these irregularity disturbances, interactions of the tool in the form of changes perpendicular and parallel relative to the workpiece were analyzed...
-
Sea surface temperature retrieval from MSG/SEVIRI data in the Baltic Sea area
Publication -
Molecular dynamics study on the role of solvation water in the adsorption of hyperactive AFP to the ice surface
PublicationUsing computer simulations, the early stages of the adsorption of the CfAFP molecule to the ice surface were analyzed. We found that the ice and the protein interact at least as early as when the protein is about 1 nm away from the ice surface. These interactions are mediated by interfacial solvation water and are possible thanks to the structural ordering of the solvent. This ordering leads to positional preference of the protein...
-
Organic carbon fluxes of a glacier surface: a case study of Foxfonna, a small Arctic glacier
PublicationArctic glaciers are rapidly responding to global warming by releasing organic carbon (OC) to downstream ecosystems. The glacier surface is arguably the most biologically active and biodiverse glacial habitat and therefore the site of important OC transformation and storage, although rates and magnitudes are poorly constrained. In this paper, we present measurements of OC fluxes associated with atmospheric deposition, ice melt,...
-
Vertical motions damping model test of a lifeboat lowered onto a flat sea surface
PublicationThe article presents the experiment’s results of the lifeboat model lowered with an initial speed and then released to fall onto a flat water surface. The purpose of the research is to determine the trajectory of the vertical boat motion and describe it with a mathematical model. This is closely related to determining the damping factor since the vertical motion is damped and the lifeboat gets balanced and stops moving after some...
-
Measurement system for nonlinear surface spectroscopy by atomic force microscopy for corrosion processes monitoring
PublicationIn addition to traditional imaging the surface, atomic force microscopy (AFM) enables wide variety of additional measurements. One of them is higher harmonic imaging. In tapping mode the nonlinear contact between tip and specimen results in higher frequency vibrations. More information available from the higher harmonics analysis proves to be helpful for more detailed imaging. Such visualization is especially useful for heterogeneous...
-
Ligand-Modified Boron-Doped Diamond Surface: DFT Insights into the Electronic Properties of Biofunctionalization
PublicationWith the increasing power of computation systems, theoretical calculations provide a means for quick determination of material properties, laying out a research plan, and lowering material development costs. One of the most common is Density Functional Theory (DFT), which allows us to simulate the structure of chemical molecules or crystals and their interaction. In developing a new generation of biosensors, understanding the nature...
-
Drop-coating deposition surface-enhanced Raman spectroscopy on silver substrates for biofluid analysis
PublicationUtilization of surface-enhanced Raman spectroscopy as a measurement technique is of particular interest in biodetection due to its superb chemical specificity and high sensitivity. The use of SERS substrates further improve this method by massive enhancement of the molecule Raman spectrum, permitting very low levels of detection. Therefore it is important to seek for new ways to develop reliable substrates, which are quickly and...
-
Size-Controlled Synthesis of Pt Particles on TiO2 Surface: Physicochemical Characteristic and Photocatalytic Activity
PublicationDifferent TiO2 photocatalysts, i.e., commercial samples (ST‐01 and P25 with minority of rutile phase), nanotubes, well‐crystallized faceted particles of decahedral shape and mesoporous spheres, were used as supports for deposition of Pt nanoparticles (NPs). Size‐controlled Pt NPs embedded in TiO2 were successfully prepared by microemulsion and wet‐impregnation methods. Obtained photocatalysts were characterized using XRD, TEM,...
-
Selected anionic and cationic surface active agents determined in river sediments – the Klodnica catchment
PublicationSurface active agents (SAAs) are specific compounds that contain hydrophilic/ hydrophobic group in their molecules named as amphiphilic structures. According to charge on the hydrophilic part of surfactants they can be classified into three main groups: anionic, cationic and non-ionic compounds. Due to the amphiphilic structure of SAAs they have specific properties (e.g. ability to adsorption at different surfaces, reduction of...
-
INFORMATION ABOUT DYNAMICS OF THE SEA SURFACE AS A MEANS TO IMPROVE SAFETY OF THE UNMANNED VESSEL AT SEA
PublicationOne of the fundamental states of the sea surface is its heave. Despite of years of the intense scientific inquiry, no clear understanding of the influence of this aspect on the dynamics of the sea environment has emerged. The separation of two nearby fluid elements which one may observed for example as a free floating of small objects on the sea surface (rescuers on the rough sea or small research vessels) is caused by the interaction...
-
Comparison of heat transfer characteristics in surface cooling with boiling microjets of water, ethanol and HFE7100
PublicationThe basis of microjet technology is to produce jets which impinge the surface at the stagnation point with a very high kinetic energy. Main objective of this paper was to investigate the physical phenomena occurring on solid surfaces upon impingement of the single microjet in case of three fluids, namely water, ethanol and HFE7100. Intense heat transfer in the impact zone of microjet has been examined and described with precise...
-
Evaluation of turning with different cooling-lubricating techniques in terms of surface integrity and tribologic properties
Publication -
The Evaluation of Surface Integrity During Machining of Inconel 718 with Various Laser Assistance Strategies
Publication -
Investigations on surface induced tribological characteristics in MQCL assisted machining of duplex stainless steel
Publication -
Influence of geometry and surface morphology of the U-tube on the fluid flow in the range of various velocities
Publication -
Advances in Hard–to–Cut Materials: Manufacturing, Properties, Process Mechanics and Evaluation of Surface Integrity
Publication -
Application of TOF-SIMS Method in the Study of Wetting the Iron (111) Surface with Promoter Oxides
Publication -
Impact of chitosan/noble metals-based coatings on the plasmochemically activated surface of NiTi alloy
Publication -
Surface phenomena in discotic liquid crystals investigated using polarized FTIR transmission spectroscopy
Publication -
Impact of TiO2 Surface Defects on the Mechanism of Acetaldehyde Decomposition under Irradiation of a Fluorescent Lamp
Publication -
New procedure of silica gel surface modification. Preparation of gaseousstandard mixtures for calibration purposes.
PublicationPrzedstawiono nową procedurę modyfikacji powierzchni żelu krzemionkowego z wykorzystaniem trimetyloaminy jako odczynnika. Próbki chemiczne modyfikowanego nośnika zostały wykorzystane do sporządzenia gazowych mieszanin wzorcowych (chlorek metylu jako składnik mierzony) techniką termicznego rozkładu związków powierzchniowych. Głównym celem badań było sprawdzenia przydatności nowej procedury modyfikacji powierzchni żelu do...
-
Simultaneous detrmination of selected phenoxyacid herbicides and chlorophenols in surface and seawater by HPLC coupled to DAD.
PublicationDo badań wykorzystano metodę ekstrakcji do fazy stałej (SPE) w celu wzbogacenia analitów. Ekstrakty analizowano techniką wysokosprawnej chromatografii cieczowej (HPLC) z detekcją DAD. Opracowana metoda umożliwia oznaczenie 14 związków z grupy kwasów fenoksyoctowych i chlorofenoli w czasie 22 min. Odzysk analitów wynosił powyżej 60% dla fenoksykwasów i powyżej 70% w przypadku chlorofenoli. Granica oznaczalności dla oznaczania...
-
Optimizing acoustic field intesity algorithms using the sound ray surface density method.
PublicationW artykule przedstawiono zagadnienia optymalizacji algorytmów komputerowych obliczeń rozkładów natężeń pola akustycznego w akwenie w zależności od za- mierzonych warunków hydrologicznych pod kątem skrócenia czasu obliczń.
-
Study of free convective boundary layer of isothermal lateral surface of axisymmetrical horizontal body
PublicationPrzedstawiono rozwiązanie równań Naviera-Stokesa i Fouriera-Kirchhoffa we współrzędnych tau i sigma. Pierwsza jest styczną a druga normalną do konwekcyjnych linii prądu, wzdłuż jakich porusza się ogrzany od powierzchni płyn. Wynik w postaci równania na grubość warstwy przyściennej zweryfikowano dla granicznych przypadków ciała obrotowego o poziomej osi symetrii (stożka poziomego i kołowej pionowej płyty).