Filtry
wszystkich: 1487
wyświetlamy 1000 najlepszych wyników Pomoc
Wyniki wyszukiwania dla: DELAYED-CHOICE EXPERIMENT
-
New approach for the synthesis of Ag3PO4-graphene photocatalysts
PublikacjaA facile and effective plasma sputtering method for the preparation of a visible light active photocatalyst - rhombic dodecahedral silver phosphate Ag3PO4 covered with nanographene (Ag3PO4-GR) with improved stability has been developed. Proposed method allows for the usage of readily available materials for nanographene sputtering and for easy scaling-up. The stability improvement, confirmed by visible light-induced phenol degradation...
-
Manoeuvring forces on azimuthing podded propulsor model
PublikacjaThis paper presents the preliminary part of comprehensive manoeuvring open- water tests of a gas carrier model. The paper focuses on open water experiments with an azimuthing podded propulsor. The test program was carried out in the cavitation tunnel and the large towing tank of Ship Hydromechanics Division, Ship Design and Research Centre, Gdańsk. The pod was tested as a pushing unit with a 161.3 mm diameter propeller. Steering...
-
The influence of the carbon equivalent on the weldability of high-strength low-alloy steel in the water environment
PublikacjaFrom many years, the high strength low alloy steels are often used for offshore constructions. This constructions, due to the environment in which they work, require more frequent repairs than the constructions from the land. For economic reasons, repairs take place in the underwater conditions, however water significantly decreases the weldability of steel. The paper presents the results of the CTS weldability test for S460ML...
-
Synchronized six-step voltage generation in high-speed PMSM drive
PublikacjaSynchronized voltage generation has already been considered in the context of pulse width modulation (PWM). References prove that synchronized PWM substantially decreases subharmonics in inverter output voltage when operating with low switching-to-fundamental frequency ratio. This paper identifies problems of unsynchronized voltage generation in electric drives under six-step inverter operation. Guidelines for the synchronization...
-
Experimental investigations and simulations of the microturbine unit with permanent magnet generator
PublikacjaIn dispersed power generation, low power devices are used for local combined generating of heat end electric power. There are developing concepts of micropower plants with electric generators driven by steam or gas microturbines. The paper presents the results of an experimental investigations of the microturbine set consists of the turbine with partial admission, permanent magnet generator and three phase AC-to-DC rectifier. The...
-
Underwater Navigation System Based on Doppler Shifts of a Continuous Wave
PublikacjaThe paper describes a concept of an underwater navigation system designed to determine the location and speed of its ROVs or divers. Conducted by the Department of Marine Electronic Systems at the Gdansk University of Technology for several years, research has focused on navigation systems which determine positions on the basis of Doppler shifts of echo signals reflected from a moving object. This article presents a different version...
-
Limitations of Emotion Recognition in Software User Experience Evaluation Context
PublikacjaThis paper concerns how an affective-behavioural- cognitive approach applies to the evaluation of the software user experience. Although it may seem that affect recognition solutions are accurate in determining the user experience, there are several challenges in practice. This paper aims to explore the limitations of the automatic affect recognition applied in the usability context as well as...
-
Speed Sensorless AC Drive with Inverter LC Filter and Fault Detection Using Load Torque Signal
PublikacjaThe industrial development in recent years has seen a major increase in the use of induction motors, whereby the cost has to be as low as possible and the lifetime as long as possible. To follow up this desire, investigations in this area have become very intense. For that reason, this paper presents a solution for driving an induction motor and simultaneous fault detection with no need for additional sensors. In order to achieve...
-
Limitations of Emotion Recognition from Facial Expressions in e-Learning Context
PublikacjaThe paper concerns technology of automatic emotion recognition applied in e-learning environment. During a study of e-learning process the authors applied facial expressions observation via multiple video cameras. Preliminary analysis of the facial expressions using automatic emotion recognition tools revealed several unexpected results, including unavailability of recognition due to face coverage and significant inconsistency...
-
Exploring the impact of cultural context on eye-tracking studies of architectural monuments in selected European cities: Sustainable heritage management.
PublikacjaSustainable management of architectural heritage requires conducting an inclusive diagnosis of users’ opinions, considering both residents and tourists as the recipients of urban space. Given the cultural diversity within these groups, proposing the use of eye-trackers (ET) as an alternative to traditional public consultation prompts the need to assess the method’s advantages and disadvantages. It remains uncertain whether individuals...
-
Problem of aggregation in dye-DNA interaction, calorimetry studies
PublikacjaNucleic acids are the biological target for many antimicrobial, antitumor and antiviral drugs. Ligand-DNA interactions can be classified into two major categories: 1. covalent binding, which can provide to intermolecular adducts, 2. physico-chemical interactions, which can be divided into intercalation (e.g. adriamycin) or groove binding (e.g. dystamycin). There are several methods to investigate interactions between drug and DNA....
-
Discussion of Derivability of Local Residual Stress Level from Magnetic Stray Field Measurement
PublikacjaThe NDT procedure dubbed ‘metal magnetic memory’ method and the related ISO 24497 standard has found wide industrial acceptance in some countries, mainly in Russia and China. The method has been claimed by some researchers (Roskosz and Bieniek in NDT&E Int 45:55–62, 2012; Wilson et al. in Sens Actuators A 135:381–387, 2007) as having potential for quantitative determination of local residual stress state in engineering structures,...
-
An empirical study on the impact of AspectJ on software evolvability
PublikacjaSince its inception in 1996, aspect-oriented programming (AOP) has been believed to reduce the effort required to maintain software systems by replacing cross-cutting code with aspects. However, little convincing empirical evidence exists to support this claim, while several studies suggest that AOP brings new obstacles to maintainability. This paper discusses two experiments conducted to evaluate the impact of AspectJ (the most...
-
INTENSYFIKACJA WYMIANY CIEPŁA W WYMIENNIKU WĘŻOWNICOWYM Z WYKORZYSTANIEM PRZEGRÓD O RÓŻNEJ GEOMETRII
PublikacjaW pracy zaprezentowano możliwości wykorzystania pasywnej intensyfikacji wymiany ciepła w postaci przegród dla podniesienia efektywności energetycznej wymiennika wężownicowego. Badania zostały przeprowadzone z wykorzystaniem modułowego wymiennika z wężownicą w postaci grzałki elektrycznej. Medium odbierającym ciepło była woda o stałych parametrach cieplnoprzepływowych na wlocie do modułu. Pomiary przeprowadzono dla szerokiego zakresu...
-
Statistics of AFM current-voltage curves
Dane BadawczeMapping surface electrical conductivity offers enormous cognitive possibilities regarding the structure and properties of modern materials. The technique invented for this purpose (Conductive AFM) by Murrel's team and colleagues allows independent monitoring of the local conductivity of materials in correlation with the topographic profile. The mentioned...
-
Człowiek i jego samochód - relacje w strukturach mieszkaniowych w warunkach zrównoważonego rozwoju. Zapis refleksji
PublikacjaJakość środowiska zbudowanego - przekształcanego i tworzonego dla coraz liczniejszych pokoleń mieszkańców jest przedmiotem wieloletniej i narastającej dyskusji zawodowej środowiska architektonicznego.Ludzka potrzeba samorealizacji poprzez codzienną aktywność, działalność zawodową, przyjmowane role społeczne wpływa na kształtowanie indywidualnych modeli codzienności miejskiej, na decyzje o wyborach miejsca zamieszkania, miejsca...
-
Analysis of the process of water entry of an amphibious vehicle
PublikacjaThe paper presents a method of computational and experimental analysis of the process of water entry of an amphibious vehicle. The computational method is based on the Reynolds Averaged Navier-Stokes Equations (RANSE) solver and the xperiment was carried out in the towing tank at Ship Design and Research Centre S.A. with the use of a scale model. The analysis was focused on the safety of water entry, i.e. the maximum pitch and...
-
Robustness of quantum-randomness expansion protocols in the presence of noise
PublikacjaIn this paper we investigate properties of several randomness generation protocols in the device independent framework. Using Bell-type inequalities it is possible to certify that the numbers generated by an untrusted device are indeed random. We present a selection of certificates which guarantee two bits of randomness for each run of the experiment in the noiseless case and require the parties to share a maximally entangled state....
-
Selection of excitation signals for high-impedance spectroscopy
PublikacjaA method of fast impedance spectroscopy of technical objects with high impedance (|Zx| > 1 GOhm) is evaluated in this paper. An object is excited with a signal generated by a digital-to-analog converter (DAC) located on the U2531A DAQ module. Response signals proportional to current flowing through and voltage across the measured object are sampled by analog-to-digital converters (ADC) in the DAQ module. The object impedance spectrum...
-
Accurate design of pseudoelliptic inline SIW filters with frequency-dependent couplings
PublikacjaThis paper presents an accurate synthesis method for inline SIW (Substrate Integrated Waveguide) generalized Chebyshev bandpass filters with frequency-dependent couplings. The technique is based on the synthesis of a coupling matrix that takes into account the impedance of the frequency-dependent stub. Thus, a loading effect compensation in adjacent resonators (via resonant frequency adjustment) and coupling elements (via coupling-value...
-
Visual Object Tracking System Employing Fixed and PTZ Cameras
PublikacjaThe paper presents a video monitoring system utilizing fixed and PTZ cameras for tracking of moving objects. First type of camera provides image for background modelling, being employed for foreground objects localization. Estimated objects locations are then utilised for steering of PTZ cameras when observing targeted objects with high close-ups. Objects are classified into several classes, then basic event detection is being...
-
Remarks on steam condensation modeling related to steam turbine large output
PublikacjaIn the paper numerical simulations have been performed to predict the performance of the diferent steam models. All of the considered models of steam condensation have been validated on the base of benchmark experiment employing expansion in nozzle and next on the low pressure part of the steam turbine equipped with the so-called Baumann stage. For numerical analysis three models have been finally used - the ideal steam model without...
-
A new technology of crude vegetable oil degumming with rhamnolipid solutions
PublikacjaA new technology of crude vegetable oil degumming is described. It is based on rhamnolipid biocomplex solution application for phosphatides removal. The rhamnolipid biocomplex produced by Pseudomonas sp. PS-17 was used as biosurfactant. Rapeseed oil was used in all experiments. First, it was degummed with H2SO4 in order to remove all phosphatides and then 1% (w/w) of granular soybean lecithin was added. Model oil was treated with...
-
Detection of petroleum products using optical coherence tomography
PublikacjaIn this work, we present a novel method developed for the analysis of the properties of thin layers for detecting petroleum products on a water surface using a commercially available optical coherence tomography (OCT) system. The spectral density analysis of the signal from a spectroscopic OCT (S-OCT) enables us to perform the precision calculation of the thin layer thickness and other properties like homogeneity, and dispersion,...
-
Wireless Local Area Network Technologies as Communication Solutions for Unmanned Surface Vehicles
PublikacjaAs the number of research activities and practical deployments of unmanned vehicles has shown a rapid growth, topics related to their communication with operator and external infrastructure became of high importance. As a result a trend of employing IP communication for this purpose is emerging and can be expected to bring significant advantages. However, its employment can be expected to be most effective using broadband communication...
-
A numerical and experimental analysis of multi-hole orifice in turbulent flow
PublikacjaIn this research study, the comprehensive metrological analysis is investigated for a 4-hole orifice with module m = 0.25 installed in the pipeline with an internal diameter of 50 mm. A detailed numerical simulation was performed for the turbulence models: k-ε-realizable and k-ω-BSL. The novelties of the research include model validation by comparing the results of numerical studies with the experiment conducted in the area of...
-
Study of Soil Temperature and Moisture Changes in a Physical Model of an Underground Cable Line
PublikacjaThe ampacity of power cables is highly dependent on the thermal resistivity of the soil in which they are laid. The lower it is, the higher this ampacity. The thermal resistivity of the soil decreases as its moisture increases. Therefore, it is preferable that the soil around the cables has high moisture. Unfortunately, the heat generated in heavily loaded cables causes the migration of moisture from the surrounding soil, which...
-
Non-destructive Diagnostics of the Floor in the Gdańsk Crane Using Ground Penetrating Radar = Diagnostyka nieniszcząca posadzki w gdańskim Żurawiu z zastosowaniem metody georadarowej
PublikacjaThis paper presents the results of a ground penetrating radar (GPR) survey carried out at the Crane in Gdańsk. The measurements were conducted on the floor of the southern and northern towers. The aim of the experiment is to assess the possibility of detecting anomalies beneath the floor. The surveys were carried out in a non-destructive manner, using a georadar unit with 2 GHz and 400/900 MHz antennas. This paper compares the...
-
Scenario-planning solutions for waterfront flood-prone areas
PublikacjaThe aim of this article is to discuss the potential of applying scenario planning to achieve resilient and future-oriented solutions for flood-prone areas. The authors have proposed additions to scenario-planning processes based on the introduction of research-by-design architectural inquiries. Examined in this article is the insight into the testing of such a modified scenario-planning methodology during two courses that accompanied...
-
Method for Clustering of Brain Activity Data Derived from EEG Signals
PublikacjaA method for assessing separability of EEG signals associated with three classes of brain activity is proposed. The EEG signals are acquired from 23 subjects, gathered from a headset consisting of 14 electrodes. Data are processed by applying Discrete Wavelet Transform (DWT) for the signal analysis and an autoencoder neural network for the brain activity separation. Processing involves 74 wavelets from 3 DWT families: Coiflets,...
-
Adaptation of the arbitrary Lagrange–Euler approach to fluid–solid interaction on an example of high velocity flow over thin platelet
PublikacjaThe aim of this study is to analyse the behaviour of a thin plate with air flow velocities of 0.3–0.9 Ma. Data from the experiment and numerical tools were used for the analysis. For fluid–solid interaction calculations, the arbitrary Lagrange–Euler approach was used. The results of the measurements are twofold. The first one is the measurement of the flow before and after vibrating plate, i.e. pure flow plate, and the second consists...
-
A method to determine the tightening sequence for standing rigging of a mast
PublikacjaThe article proposes an alternative method to determine the sequence of generation of pre-tension forces in standing rigging of a mast. The proposed approach has been verified on both a virtual simulation experiment and laboratory tests. In this method, the desired tension values are obtained using the influence matrix which allows to calculate the effect of tension change in an individual rope on the tension distribution in the...
-
The effect of current signal filtering method on the value of cutting power while sawing wood
PublikacjaThe goal of this work was to investigate an effect of various signal pre-processings on the outline of the electrical power curve and its influence on the measured cutting force estimation. Two signal processing methods were selected for the needs of the experiment, including digital filter and wavelet transform. The filter used was Butterworth, 3rd order band-stop with the cut-out band from 45 Hz to 55 Hz. The second approach...
-
Diethyl carbonate as a green extraction solvent for chlorophenol determination with dispersive liquid–liquid microextraction
PublikacjaThe principles of green analytical chemistry indicate that the search for greener organic solvents for extraction applications is crucial. In this study diethyl carbonate (DEC) is proved to be a green solvent, as it is relatively nontoxic, obtainable from renewable resources and biodegradable. Here it is applied as an extraction solvent for chlorophenol determination in water samples with dispersive liquid–liquid microextraction....
-
Hydroxyapatite deposition on the laser modified Ti13Nb13Zr alloy
PublikacjaThe Ti13Nb13Zr alloy was subjected to laser modification with the Nd:YAG laser provided that such treatment would increase the surface roughness followed improved adhesion of hydroxyapatite (HAp) coatings The hydroxyapatite was deposited by electrophoretic method in suspension of 0.5 g HA powder and 100 ml ethyl alcohol. The deposition was carried out for 10 min at 10 V voltage followed by drying at room temperature for 24 h and...
-
Variable length sliding models for banking clients face biometry
PublikacjaAn experiment was organized in 100 bank branches to acquire biometric samples from nearly 5000 clients including face images. A procedure for creating face verification models based on continuously expanding database of biometric samples is proposed, implemented, and tested. The presented model applies to circumstances where it is possible to collect and to take into account new biometric samples after each positive verification...
-
HYDROGEN PRODUCTION PERFORMANCE IN THERMOCATALYTIC REACTOR BASED ON THE INTERMETALLIC PHASE OF NI3AL
PublikacjaThe main aim of the following paper is mathematical modelling for momentum, heat and mass transfer, which is accompanied by chemical surface reactions of the flow of the mixture helium and methanol. The thermocatalytic devices used for decomposition of hydrocarbons incorporate vertical microchannels coupling at the ends and heated to 500 oC at the walls. The results of the experiment were compared with CFD calculations to calibrate...
-
Biznesplan dla zakładu podstawowej opieki zdrowotnej o rozszerzonej działalności na obszarze dzielnicy Gdańsk-Południe
PublikacjaIn recent years we have seen the dynamic development of medical services sector in Poland. Private health centres focus on aggressive development strategy. The role of primaryhealth care facilities, which provide services financed from the public funds, declined.The purpose of the article is to present methods of strategic planning which allow toopen new healthcare entity. The next purpose is to make in practice...
-
COMPARISON OF SYSTEM ON CHIP TECHNOLOGIES FOR SPACE APPLICATIONS
PublikacjaThe paper presents a review of technologies available for the implementation of digital and mixed signal systems, particularly the system on a chip (SoC) for space applications. The phenomena encountered in the space environment are briefly presented, together with the known solutions, regarding the design of complex electronic systems. The most important norms regarding single die integrated circuits designed for space are also...
-
PCR test for Microsporum canis identification
PublikacjaMicrosporum canis, for which the natural hosts are cats and dogs, is the most prevalent zoophilic agent causing tinea capitis and tinea corporis in humans. We present here a diagnostic PCR test for M. canis, since its detection and species identification is relevant to the choice of treatment and to the understanding of a probable source of infection. An M. canis-specific PCR was evaluated using 130 clinical isolates of dermatophytes...
-
Determination of Selected Organic Acids in Animal Farm Water Samples by Ion Chromatography
PublikacjaLow molecular mass carboxylic acids (LCAs) occur in many environmental compartments due to natural processes and human activity. They are an important group of organic pollutants of waste water that mainly includes, volatile fatty acids, and also dicarboxylic, aromatic, hydroxy- and ketoacids. LCAs are present in the environment at concentrations between 1 to 5000 ppm and different methods have been reported for their determination...
-
New Challenges in Management and Economics in 21st century. Selected studies and examples
PublikacjaIn Chapter 1 authors describe the method used to assess the level of readiness of an organization to introduce the Lean Six Sigma concept supporting the Quality 4.0 assumptions, which is gaining more and more interest not only in large organizations, but also in the SME sector. Its use will be illustrated by the example of a small service company. Chapter 2 presents the characteristics of blockchain technology applications in the...
-
Heterogeneity of national accounting systems, world-class universities and financial resources: What are the links?
PublikacjaThis study investigates the relationship between university financial resources, applied accounting systems, and the place of a university in the Shanghai Ranking. We find a strong relationship between the financial resources under the control of a world-class university and the position of that university in the highest tier of the global ranking. We propose a model (available online) to predict a university’s tier in the ranking...
-
Nanoparticle Tracking Analysis of Urinary Extracellular Vesicle Proteins as a New Challenge in Laboratory Medicine
PublikacjaUrinary extracellular vesicle (uEV) proteins may be used as specific markers of kidney damage in various pathophysiological conditions. The nanoparticle-tracking analysis (NTA) appears to be the most useful method for the analysis of uEVs due to its ability to analyze particles below 300 nm. The NTA method has been used to measure the size and concentration of uEVs and also allows for a deeper analysis of uEVs based on their protein...
-
Which Curve Fits Best: Fitting ROC Curve Models to Empirical Credit-Scoring Data
PublikacjaIn the practice of credit-risk management, the models for receiver operating characteristic (ROC) curves are helpful in describing the shape of an ROC curve, estimating the discriminatory power of a scorecard, and generating ROC curves without underlying data. The primary purpose of this study is to review the ROC curve models proposed in the literature, primarily in biostatistics, and to fit them to actual credit-scoring ROC data...
-
Broadening the scope of measurement and analysis of vibrations of an organ pipe employing intensity probe, simulations, and highspeed camera
PublikacjaThis paper shows an integrated approach to measure, analyze, and model phenomena occurring in an organ pipe driven by pressurized air. The aim of this paper is two-fold, i.e., to measure the pressure signal and the intensity field around the mouth by means of an intensity probe and to visualize and observe the motion of the air jet, which represents the excitation mechanism of the system. This is realized through two techniques,...
-
New matrix-free reference material for ethene in the form of optical fibres
PublikacjaReference materials are indispensable in the qualitycontrol and quality assurance of analytical measurements. Onenovel approach to the generation of standard gaseous mixturesof toxic, reactive, volatile, labile, and malodorous substancesinvolves thermal decomposition or rearrangement, under definedtemperature conditions, of compounds immobilized, bychemical bonding, on the surface of an appropriate carrier torelease specific amounts...
-
Bicycle Traffic Model for Sustainable Urban Mobility Planning
PublikacjaModelling tools and transport models are required to assess the impact of measures for the effective planning of cycling routes in cities. This paper presents the methodology for developing a four-stage macroscopic model of bicycle traffic for the city of Gdynia, and its use in planning new bicycle routes, considering a modal shift. The model presented in this paper allows for the evaluation of the influence of the characteristics...
-
Surface effects of network materials based on strain gradient homogenized media
PublikacjaThe asymptotic homogenization of periodic network materials modeled as beam networks is pursued in this contribution, accounting for surface effects arising from the presence of a thin coating on the surface of the structural beam elements of the network. Cauchy and second gradient effective continua are considered and enhanced by the consideration of surface effects. The asymptotic homogenization technique is here extended to...
-
An Approach to Agent-Based Supporting System for IT Projects
PublikacjaAbstract. The natural development of information technology area stimulates intense growth of various technologies which support basic organization processes. The range of technologies implies appropriate management thereof, as well as accurate correspondence with conducted activities. Abandonment of activities within individual branches in favour of project approach to performed assignments (especially those connected with software...