Filters
total: 1038
filtered: 984
-
Catalog
Chosen catalog filters
Search results for: RAILWAY SUBSTRUCTURE IMPROVEMENT
-
Effect of plasma sprayed and laser re-melted Al2O3 coatings on hardness and wear properties of stainless steel
PublicationCommercially available austenic stainless steel substrate was coated with commercially available, raw Al2O3 powder applied by means of plasma spraying method and then re-melted with CO2 laser beam of various parameters. Tribological and mechanical properties of the 120 J/mm and 160 J/mm laser re-melted coatings were compared with the tribological and mechanical properties of the “as-sprayed” coating. The influence of the laser...
-
Features extraction from the electrocatalytic gas sensor responses
PublicationOne of the types of gas sensors used for detection and identification of toxic-air pollutant is an electrocatalytic gas sensor. The electrocatalytic sensors are working in cyclic voltammetry mode, enable detection of various gases. Their response are in the form of I-V curves which contain information about the type and the concentration of measured volatile compound. However,...
-
STUDY ON THE EFFECTIVENESS OF THE TURBINE CONDENSER AIR EXTRACTION SYSTEM USING HYDRO EJECTORS
PublicationThe aim of the paper is to investigate the effectiveness of the 18K380 steam turbine condenser air extraction system using hydro ejectors. Motivation for the analysis is a need of improvement of the energy conversion ratio of the power plant. To achieve this goal it is necessary to establish efficiency of each subsystem of the energy cycle. The air extraction system is not a highly power consuming system but it has great impact...
-
COLREGS compliance in Evolutionary Sets of Cooperating Ship Trajectories
PublicationIn general, Evolutionary Sets of Cooperating Ship Trajectories combine some of the assumptions of game theory with evolutionary programming and aim to find optimal set of cooperating trajectoriesof all ships involved in an encounter situation. In a two-ship encounter situation the method enables the operator of an on-board collision-avoidance system to predict the most probable behaviour of atarget and to plan the own manoeuvres...
-
Wpływ przechyłki na zjawisko postępowania zużycia bocznego szyn kolejowych w łukach poziomych
PublicationDegradacja elementów nawierzchni kolejowej jest zagadnieniem bardzo złożonym, w które uwikłane jest wiele czynników związanych między innymi z układem geometrycznym toru kolejowego, właściwościami trybologicznymi poszczególnych elementów nawierzchni, jak również z parametrami podłoża gruntowego, a także z właściwościami samych pojazdów szynowych. W artykule omówiono jeden z powyższych problemów, tj. wpływ ukształtowania toru kolejowego...
-
Oddziaływania taboru na mosty kolejowe przy zmiennych parametrach ruchu
PublicationW pracy poruszono zagadnienia związane z identyfikacją oraz modelowaniem układu dynamicznego most-pojazd ruchomy. Za element szczególnie istotny uznano czynnik obciążający. Opracowano i wdrożono metodykę identyfikacji cech dynamicznych rzeczywistego pojazdu szynowego. Eksperyment badawczy przeprowadzono dla jednostki trakcyjnej EN57, jednak nie ma żadnych ograniczeń w stosowaniu metody dla innego, konwencjonalnego taboru szynowego....
-
Effect of Processing Parameters on Strength and Corrosion Resistance of Friction Stir-Welded AA6082
PublicationThe friction stir welding method is increasingly attracting interest in the railway sector due to its environmental friendliness, low cost, and ease of producing high-quality joints. Using aluminum alloys reduces the weight of structures, increasing their payload and reducing fuel consumption and running costs. The following paper presents studies on the microstructure, strength, and corrosion resistance of AA6082 aluminum alloy...
-
Modal Analysis of a Steel Radial Gate Exposed to Different Water Levels
PublicationWith the increase in water retention needs and planned river regulation, it might be important to investigate the dynamic resistance of vulnerable elements of hydroelectric power plants, including steel water locks. The most frequent dynamic loads affecting hydroengineering structures in Poland include vibrations caused by heavy road and railway traffic, piling works and mining tremors. More destructive dynamic loads, including...
-
Modelowanie i symulacja dynamiki ruchu trakcyjnego odbieraka prądu
PublicationW artykule przedstawiono dwa modele matematyczne kolejowych odbieraków prądu. Model podstawowy opracowano na podstawie analizy konstrukcji odbieraka ze stopniami swobody w ruchu obrotowym i postępowym. Drugi tzw. model zastępczy ma obydwa stopnie swobody w ruchu postępowym. Przedstawiono prosty sposób wyznaczenia wartości parametrów modelu zastępczego na podstawie wyników symulacji modelu odbieraka podstawowego. Model zastępczy,...
-
Analiza wyników monitoringu odbieraków prądu w warunkach ruchowych na linii kolejowej
PublicationOmówiono metodę ciągłego monitorowania stanu odbieraków prądu na linii kolejowej w oparciu o pomiar uniesienia przewodów jezdnych sieci trakcyjnej w czasie przejazdu pociągu. Omówiono zasadę działania wdrożonego stanowiska monitoringu. Opisano algorytmy analizy danych pomiarowych - w szczególności oszacowania siły statycznej odbieraka prądu - i przyjęte kryteria oceny odbieraka. W analizie bierze się pod uwagę także prędkość pociągu...
-
Building the Learning Environment for Sustainable Development: a Co-creation approach
PublicationEducation for sustainable development supports the improvement of knowledge, skills, attitudes and behaviors related to global challenges such as climate change, global warming and environmental degradation, among others. It is increasingly taking place through projects based on information and communication technologies. The effectiveness of the actions taken depends not only on the quality of the project activities or the...
-
ADT in mammography
PublicationWe discuss limitations of the known methods of IR imaging in diagnostics of breast cancer. In conclusion we show that for practical reasons one requires new approaches because the known methods based on simple observation of external temperature distribution are not fully effective. Even advanced pattern recognition could not help too much for static images. We ask the question: may active dynamic thermography, known in nondestructive...
-
Methods of liquid biofuels production - the bioethanol example.
PublicationEthanol is used in chemical and food industry, mainly either in the synthesis or as a solvent. The newest application of ethanol is as a fuel. This alcohol, produced on an industrial scale from crop waste, is widely known under the name bioethanol. It could be used as a fuel by itself or in a mixture with gasoline. Today, there are several technologies for bioethanol production known. The relatively simple method of obtaining bioethanol...
-
METHODS OF LIQUID BIOFUEL PRODUCTION – THE BIOETHANOL EXAMPLE
PublicationEthanol is used in chemical and food industry, mainly either in the synthesis or as a solvent. The newest application of ethanol is as a fuel. This alcohol, produced on an industrial scale from crop waste, is widely known under the name bioethanol. It could be used as a fuel by itself or in a mixture with gasoline. Today, there are several technologies for bioethanol production known. The relatively simple method of obtaining bioethanol...
-
Numerical study on seismic response of a base-isolated building modelled with shell elements
PublicationSeismic isolation is counted among the most popular and effective means of protecting structures against earthquake forces. Base isolators, like Lead-Rubber Bearings (LRB), High-Damping Rubber Bearings (HDB) or Friction Pendulum Systems (FPS) are extensively used in practice in many earthquake-prone regions of the world. The present paper reports the results obtained from the numerical study on seismic response of a base-isolated...
-
EFFICIENCY OF GAS MIXTURES DETECTION BY RESISTIVE GAS SENSORS
PublicationResistive gas sensors are very popular and are commonly used to detect various gases and their mixtures. Their main disadvantage is very limited selectivity. Practical use of gas sensors in environmental applications (e.g., in sewage systems to protect workers, in air conditioning systems to monitor atmosphere quality) requires determination of concentration of a few mixed gases at the same time. We would like to present recent...
-
Application of ferric chloride for arsenic removal in the integrated process: coagulation/microfiltration
PublicationThe study presents results of using iron coagulation integrated with microfiltration to remove arsenic from water. Tested samples of natural groundwater contained approximately 32 μg/L of arsenic, 0.13 mg/L of iron and 0.085 mg/L of manganese. As a coagulant the aqueous solution of ferric chloride was dosed in portions from 1.0 to 10.5 mg/L. In the research microfiltration membranes with 400 kDa MWCO were used. Tests indicated...
-
Bio-Based Polyurethane Composites and Hybrid Composites Containing a New Type of Bio-Polyol and Addition of Natural and Synthetic Fibers
PublicationThis article describes how new bio-based polyol during the liquefaction process can be obtained. Selected polyol was tested in the production of polyurethane resins. Moreover, this research describes the process of manufacturing polyurethane materials and the impact of two different types of fibers—synthetic and natural (glass and sisal fibers)—on the properties of composites. The best properties were achieved at a reaction temperature...
-
Interactions between hydration spheres of two different solutes in solution: The least squares fitting with constraints as a tool to determine water properties in ternary systems
PublicationBiological systems are complex and the problem of their description lies in mutual interactions between their components. This paper is focused on model experiment-based studies which can reduce these difficulties. The ternary aqueous N-methylacetamide (NMA)–Na2HPO4 system has been studied by means of the FTIR spectroscopy. A novel difference spectra method aimed to extract the spectral contribution of water affected simultaneously...
-
Improving social competencies of architecture students through participatory design of marketplace regeneration
PublicationThe article discusses the involvement of architecture students in actual urban regeneration projects through participatory design and tray to respond question how it can improve students social competences, and benefit their future careers as architects and urban planners. By using the example of the student workshops conducted in 2019 at the Faculty of Architecture, GdanskTech, the article discusses the specific methods applied...
-
Analytical Estimation of Power Losses in a Dual Active Bridge Converter Controlled with a Single-Phase Shift Switching Scheme
PublicationMicro-grid solutions around the world rely on the operation of DC/DC power conver- sion systems. The most commonly used solution for these topologies is the use of a dual active bridge (DAB) converter. Increasing the efficiency and reliability of this system contributes to the improvement in the stability of the entire microgrid. This paper discussed an analytical method of energy efficiency and power loss estimation in a single...
-
Enhancement of the Magnetoresistance in the Mobility‐Engineered Compensated Metal Pt 5 P 2
PublicationThe magnetoresistance (MR) in nonmagnetic materials continues to be a fertile research area in materials science. The search for giant, positive MR has been limited to a rather small window of materials such as high-mobility semimetals in single-crystalline form. Here, the observation of a very large positive MR in metallic Pt5P2 in polycrystalline form is reported. The observations reveal that improvement of the crystallinity...
-
Potential and Use of the Googlenet Ann for the Purposes of Inland Water Ships Classification
PublicationThis article presents an analysis of the possibilities of using the pre-degraded GoogLeNet artificial neural network to classify inland vessels. Inland water authorities monitor the intensity of the vessels via CCTV. Such classification seems to be an improvement in their statutory tasks. The automatic classification of the inland vessels from video recording is a one of the main objectives of the Automatic Ship Recognition and...
-
Improvements to the STEAM-based teaching of architectural drawing
PublicationThe author of this article presents a systemic approach to improving the teaching of architectural drawing courses for engineers in the 21st Century. In this era of rapid development of digital technologies, the traditional teaching structure should be redefined to a purpose-oriented dynamic model. The existing, generally accepted teaching models have already proved successfully based on the practice-oriented STEAM programme, which...
-
Critical review of electronic nose and tongue instruments prospects in pharmaceutical analysis
PublicationElectronic nose (enose, EN) and electronic tongue (etongue, ET) have been designed to simulate human senses of smell and taste in the best possible way. The signals acquired from a sensor array, combined with suitable data analysis system, are the basis for holistic analysis of samples. The efficiency of these instruments, regarding classification, discrimination, detection, monitoring and analytics of samples in different types...
-
Hydraulic conductivity of a biopolymer treated sand
PublicationThis paper presents results of laboratory assessment of creating seepage barriers in a sandy soil using biopolymer additives (bio substance), which consist of polysaccharides and water. Polysaccharides strongly interact with water to produce a viscous suspension. The aim of the conducted work was to investigate the influence of a biosubstance employed in a highly permeable sandy soil. The amount of the biopolymer used in a sample...
-
Improved Uniform Sampling in Constrained Domains for Data-Driven Modelling of Antennas
PublicationData-driven surrogate modelling of antenna structures is an attractive way of accelerating the design process, in particular, parametric optimization. In practice, construction of surrogates is hindered by curse of dimensionality as well as wide ranges of geometry parameters that need to be covered in order to make the model useful. These difficulties can be alleviated by constrained performance-driven modelling with the surrogate...
-
Experimental verification of visual method for measuring displacements of contact line elements
PublicationThe increase of rail vehicles speed, as well as the increase of their power, puts high demands on the power delivery system for traction vehicles The most critical point in the vehicle's power supply circuit is the contact between the current collector and contact wires. Ensuring a reliable co-operation of the current collector and contact line, requires technical development...
-
Adapting new tools of urban freight management based on Gdynia’s dedicated delivery bays example – an analysis of the process
PublicationThe article presents an analysis of a process which ultimately helped Gdynia to designate pilot delivery sites in its downtown area using international experience. A verification was conducted of policy transfer theory and its practical implementation based on an URBACT Freight Tails project. While the choice of the solution was based on critical analysis of existing practical examples, it needed to be adapted to the local conditions...
-
Statistical analysis and robust design of circularly polarized antennas using sequential approximate optimization
PublicationIn the paper, reliable yield estimation and tolerance-aware design optimization of circular polarization (CP) antennas is discussed. We exploit auxiliary kriging interpolation models established in the vicinity of the nominal design in order to speed up the process of statistical analysis of the antenna structure at hand. Sequential approximate optimization is then applied to carry out robust design of the antenna, here, oriented...
-
Some geomechanical properties of a biopolymer treated medium sand
PublicationSome geomechanical properties of a biopolymer treated medium sand. This paper presents a laboratory assessment of geomechanical properties of sandy soil improved by biopolymer application. Additives (biosubstance) consist of polysaccharides and water. Biosubstance used in the project was xanthan gum, which comes from bacteria Xanthomonas campestris. Triaxial shear compression tests and unconfi ned compression tests were carried...
-
Evaluating experimental molecular physics studies of radiation damage in DNA*
PublicationThe field of Atomic and Molecular Physics (AMP) is a mature field exploring the spectroscopy, excitation, ionisation of atoms and molecules in all three phases. Understanding of the spectroscopy and collisional dynamics of AMP has been fundamental to the development and application of quantum mechanics and is applied across a broad range of disparate disciplines including atmospheric sciences, astrochemistry, combustion and environmental...
-
Low-Cost Behavioral Modeling of Antennas by Dimensionality Reduction and Domain Confinement
PublicationBehavioral modeling has been rising in importance in modern antenna design. It is primarily employed to diminish the computational cost of procedures involving massive full-wave electromagnetic (EM) simulations. Cheaper alternative offer surrogate models, yet, setting up data-driven surrogates is impeded by, among others, the curse of dimensionality. This article introduces a novel approach to reduced-cost surrogate modeling of...
-
Fluid–Structure Interaction methods for the progressive anatomical and artificial aortic valve stenosis
PublicationCardiovascular system diseases, as aortic valve stenosis, are the main cause of mortality and morbidity among patients. There is still a room for enhancement of the diagnostic and therapeutic procedures, which will lead to improvement of the treatment. One of the remedies are the computer tools to support the medical diagnoses and prostheses design. The development of a procedure for modeling the aortic valves: anatomical tricuspid...
-
Quasi-ciągły pomiar geometrii rozjazdów kolejowych
PublicationW czasie budowy nowych torów i rozjazdów kolejowych, jak również w procesie ich utrzymania, należy wykonać odpowiednie pomiary i ocenić stan geometrii badanej infrastruktury. Pomiary te mogą być wykonane z wykorzystaniem jednego z trzech systemów pomiarowych: pojazdami pomiarowymi, maszynami do budowy i utrzymania lub urządzeniami lekkimi i ręcznymi. W artykule przedstawiona została metoda pomiarów szerokości toru i przechyłki...
-
Koncepcja doskonalenia marketingu nowych technologii w Politechnice Gdańskiej
PublicationW rozdziale podjęto problem doskonalenia wykorzystania dorobku współczesnego marketingu w przygotowaniu i oferowaniu nowych technologii, oparte na doświadczeniach Politechniki Gdańskiej (PG). Omówiono pojęcia, cechy, korzyści i uwarunkowania współczesnego marketingu, jak też istoty nowych technologii i sposobów transferu z jednostek naukowo-badawczych do gospodarki. Przedstawiono dotychczasowe doświadczenia transferu i komercjalizacji...
-
Ocena kosztu cyklu życia szyn kolejowych w modernizacji układów geometrycznych
PublicationW pracy przedstawiono uwarunkowania historyczne, które doprowadziły do opracowania metod szacowania kosztu życia inwestycji. Opisano podstawowe założenia LCC według modelu przedstawionego w Normach oraz opracowanego w projekcie INNOTRACK. Zaproponowano połączenie powyższych metod i dostosowanie ich do oceny kosztu życia szyn kolejowych w Polce. Przedstawiono elementy wpływające na koszt utrzymania nawierzchni szynowej oraz metody...
-
Badania wstępne możliwości oceny stanu powierzchni tocznej szyn za pomocą zjawisk wibroakustycznych
PublicationW artykule przedstawiono wstępną koncepcję możliwości wykorzystania zjawisk wibroa-kustycznych w celu oceny stanu powierzchni tocznych szyn. Scharakteryzowano metodykę, zakres badań oraz wybór punktów lokalizacyjnych. Badania wstępne obejmowały pomiary drgań i hałasu na referencyjnym odcinku toru oraz na odcinku toru z wadą squat. Pomiary przeprowadzono na dwóch liniach kolejowych nr 213 Reda – Hel oraz 131 Chorzów Batory – Tczew....
-
Modulo N Backoff Scheme for effective QoS differentiation and increased bandwidth utilization in IEEE 802.11 networks
PublicationThe paper presents a new "modulo N" channel access scheme for wireless Local Area Networks (WLANs). The novel solution derives from the Distributed Coordination Function (DCF) of the IEEE 802.11 standard, further elaborated as Enhanced Distribution Channel Access (EDCA) by the 802.11e draft specification. The main innovation concerns improvement of the binary exponential backoff scheme used for collision avoidance in 802.11 networks....
-
Electrocatalytic gas sensor with reference layer
PublicationIn recent years electrochemical gas sensors based on solid state electrolytes have been intensively developed. They are easy to obtain, use and relative durable. Nasicon is one of the most promising materials, which have been used in construction of gas sensors. Most of these devices work in potentiometric or amperometric mode. However, some works are dedicated to sensors working in electrocatalytic mode. Principle of operation...
-
Polymeric Bearings – A New Base Isolation System to Reduce Structural Damage during Earthquakes
PublicationBase isolators, like lead rubber bearings, high damping rubber bearings or friction pendulum systems are extensively used in practice in many seismically active regions to protect structures against earthquake forces. The present paper reports the results obtained from the experimental study aimed to determine the effectiveness of the Polymeric Bearings in suppressing structural vibrations during dynamic excitations and therefore...
-
Reduction of vibrations of steel structure models with Polymeric Bearings - experimental study
PublicationEarthquake-induced ground motions are the most severe and unpredictable threats to the structures all around the world. Therefore, designing earthquake protective systems has become an extremely challenging problem in civil engineering. Base isolation is one of the most popular and widely adopted methods of protecting structures against earthquake forces. The present paper reports the results obtained from the shaking table experimental...
-
Soxhlet Extraction and New Developments Such as Soxtec in: Comprehansive Sampling and Sample Preparation
PublicationSoxhlet extraction is one of the most popular techniques for extraction of analytes from solid materials. Since its discovery in 1879, the standard Soxhlet technique has been routinely applied in almost every analytical laboratory. Up to this day, Soxhlet extraction technique remains a standard technique to which the performance of modern extraction techniques is compared.Over the years, an intensive research on different modifications...
-
seafloor characterisation combined approach using multibeam sonar echo signal processing and image analysis
PublicationThe authors propose the approach to seafloor characterisation which relies on the combined, concurrent use of two different techniques: (i) multibeam sonar image analysis and (ii) multibeam seabed echoes processing. The first technique is based on constructing the grey-level sonar images of the seabed extracted from the echoes received in the consecutive soundings. Then, the set of parameters describing the local region of sonar...
-
Optoelectronic system for monitoring of thin diamond layers growth
PublicationDevelopment of the optoelectronic system for monitoring of diamond/DLC (Diamond-Like-Carbon) thin films growth during mu PA ECR CVD (Microwave Plasma Assisted Electron Cyclotron Resonance Chemical Vapour Deposition) process is described. The multi-point Optical Emission Spectroscopy (OES) and Raman spectroscopy were employed as non-invasive optoelectronic tools. Dissociation of H-2 molecules, excitation and ionization of hydrogen...
-
Pendant Proton-Relays Systematically Tune the Rate and Selectivity of Electrocatalytic Ammonia Generation in a Fe-Porphyrin Based Metal-Organic Framework
PublicationElectrocatalytic nitrite reduction (eNO2RR) is a promising alternative route to produce ammonia (NH3). Until now, several molecular catalysts have shown capability to homogeneously reduce nitrite to NH3, while taking advantage of added secondary-sphere functionalities to direct catalytic performance. Yet, realizing such control over heterogeneous electrocatalytic surfaces remains a challenge. Herein, we demonstrate that heterogenization...
-
Economics of credit scoring management
PublicationCredit scoring models constitute an inevitable element of modern risk and profitability management in retail financial lending institutions. Quality,or separation power of a credit scoring model is usually assessed with the Gini coefficient. Generally, the higher Gini coefficient the better, as in this way a bank can increase number of good customers and/or reject more bad applicants. In...
-
Improving carbon dioxide capture in aqueous ammonia solutions by fine SiO2 particles
PublicationAmmonia solutions are considered to be effective solvents for carbon dioxide absorption. Despite the numerous advantages of these solvents, their high volatility is a significant technical and economic problem. Therefore, in this work, silica particles were used as additives to improve CO2 absorption and inhibit NH3 desorption. SiO2 microparticles and colloidal SiO2 particles in the concentration range of 0-0.15 wt.% were used...
-
Adaptive Sampling for Non-intrusive Reduced Order Models Using Multi-Task Variance
PublicationNon-intrusive reduced order modeling methods (ROMs) have become increasingly popular for science and engineering applications such as predicting the field-based solutions for aerodynamic flows. A large sample size is, however, required to train the models for global accuracy. In this paper, a novel adaptive sampling strategy is introduced for these models that uses field-based uncertainty as a sampling metric. The strategy uses...
-
Characterization of Highly Filled Glass Fiber/Carbon Fiber Polyurethane Composites with the Addition of Bio-Polyol Obtained through Biomass Liquefaction
PublicationThis work aims to investigate the process of obtaining highly filled glass and carbon fiber composites. Composites were manufactured using previously obtained cellulose derived polyol, polymeric methylene diphenyl diisocyanate (pMDI). As a catalyst, dibutyltin dilaurate 95% and Dabco® 33-LV were used. It was found that the addition of carbon and glass fibers into the polymer matrix causes an increase in the mechanical properties...