Filters
total: 422
filtered: 391
Search results for: PA9, ALUMINIUM, WELDING
-
Zastosowania elektrochemicznej mikrowagi kwarcowej w badaniach korozyjnych
PublicationPrzegląd niniejszy opisuje zastosowania elektrochemicznej wagi kwarcowej (EQCM) w badaniach korozyjnych. Przedstawione zostały dwa główne obszary badań. Jeśli chodzi o badania mechanizmów korozji, mikrowaga elektrochemiczna była wykorzystywana jako narzędzie do testowania korozji miedzi, niklu, cynku, aluminium i stopów. Była użyteczna w określaniu mechanizmów roztwarzania albo pasywacji w różnych warunkach. Drugim kierunkiem wykorzystania...
-
Zastosowanie nagniatania w technologii złącz rurowych
PublicationW pracy przedstawiono wyniki badań i możliwości zastosowania nagniataków do tworzenia złączy rurowych przez nagniatanie zewnętrzne. Jako narzędzia do nagniatania zastosowano nagniatak jednokrążkowy z dociskiem sprężystym oraz wielorolkową głowicę z nastawianym wciskiem nagniatania. Obiektem badań było złącze rura-wkładka z aluminium AA6060 o różnych ukształtowaniach powierzchni wkładki (rowki i radełkowanie). Złącza uzyskane przez...
-
Tribological performance of PTFE-metal binary coatings in rolling/sliding contact
PublicationTribological performance of surface coatings with embedded PTFE reservoirs in rolling/sliding contact is reported. Using two different coating materials and two shapes and patterns of PTFE reservoirs test samples in the form of discs were prepared and tested in a four-ball contact configuration under loads corresponding to nominal contact pressure of 0.5 and 1.0 GPa. It was found that one coating, namely aluminium-bronze with embedded...
-
Surface Roughness Evaluation in Thin EN AW-6086-T6 Alloy Plates after Face Milling Process with Different Strategies
PublicationLightweight alloys made from aluminium are used to manufacture cars, trains and planes. The main parts most often manufactured from thin sheets requiring the use of milling in the manufacturing process are front panels for control systems, housing parts for electrical and electronic components. As a result of the final phase of the manufacturing process, cold rolling, residual stresses remain in the surface layers, which can influence...
-
Reliable method of assessing fracture properties of asymmetric bonded joints
PublicationTwo methods of assessing fracture properties of adhesive joints were studied. Two wedge tests: with continuous deflection and with force measurements were compared. Asymmetric geometry of the bonded joint was considered, i.e. two different plates of aluminium alloys: Al-Cu and Al-Mg, were bonded with epoxy DGEBA adhesive. The analytical model is shown to estimate the values of fracture properties: crack position and critical fracture...
-
Kinetics of Intermetallic Phase Precipitation in Manual Metal Arc Welded Duplex Stainless Steels
PublicationThe article presents the influence of heat treatment on the kinetics of transformations in lean duplex LDX2101 steel and a weld made of standard duplex 2209 material, which was welded by manual metal arc welding. Changes in the microstructure, hardness, and magnetic phase content were analyzed after heat treatment was conducted at a temperature of 800 °C for a period ranging from 15 to 1440 min. Light and scanning microscopy, Vickers...
-
Effect of Processing Parameters on Strength and Corrosion Resistance of Friction Stir-Welded AA6082
PublicationThe friction stir welding method is increasingly attracting interest in the railway sector due to its environmental friendliness, low cost, and ease of producing high-quality joints. Using aluminum alloys reduces the weight of structures, increasing their payload and reducing fuel consumption and running costs. The following paper presents studies on the microstructure, strength, and corrosion resistance of AA6082 aluminum alloy...
-
Metal-coated fused silica fibres as a support for immobilized compounds yielding a volatile analyte (C2H4)
PublicationPrzedstawiono wyniki badań dotyczących wykorzystania chemicznie modyfikowanych włókien szklanych pokrytych warstwą metalu (aluminium), jako nośników związków powierzchniowych. W trakcie procesu termicznego rozkładu z tak zmodyfikowanych włókien uwalnia się eten, który stanowi składnik mierzony uzyskiwanej gazowej mieszaniny wzorcowej. Ilość uwalnianego etenu zależy jedynie od długości danego rodzaju i typu modyfikowanego włókna...
-
Difficulties with evaluating resistance of materials to cavitation.
PublicationW pracy dokonano analizy wyników Międzynarodowego Testu Erozji Kawitacyjnej (ICET), któremu koordynował Instytut Maszyn Przepływowych Polskiej Akademii Nauk (IMP PAN) w Gdańsku. Kluczowe parametry wpływające na zmianę przebiegu krzywych erozji uzyskanych na stanowiskach badawczych zostały wskazane. Wykazano konieczność przeprowadzenia badań w zakresie oceny wpływu efektu skali. Zaprezentowano wyniki uzyskane na stanowiskach magnetostrykcyjnych...
-
Badania defektów w złączach adhezyjnych al/kompozyt węglowy z użyciem mikroskopii ultradźwiękowej
PublicationJednym z istotnych czynników decydujących o jakości złączy klejonych jest brak dużych pęcherzy i 'debondingów' w warstwie kleju. W celu wykrycia tych defektów można wykorzystać różne metody. Jedną z nich, przedstawioną w tej pracy do badań złączy adhezyjnych aluminium/kompozyt grafit/żywica epoksydowa, była mikroskopia ultradźwiękowa. Przeprowadzono próby ze sztucznymi wadami w złączu w celu oceny możliwości tej metody nie stosowanej...
-
Influence of laser remelting at cryogenic conditions on corrosion resistance of non-ferrous alloys
PublicationCelem nadtapiania laserowego elementów wytwarzanych z stopów aluminium, miedzi i tytanu jest uzyskanie wysokiej twadrości i odporności na korozję dla wydłużenia okresu ich eksploatacji w rezultacie ich szybkiej krystalizacji. Końcowa mikrostruktura, skład fazowy i właściwości wymienionych stopów zależą od parametrów obróbki laserowej oraz budowy wykresów równowagi fazowej. W artykule przedstawiono wpływ laserowego nadtapiania...
-
Detection of damages in a rivetted plate
PublicationThe paper presents the results of damage detection in a riveted aluminium plate. The detection method has been based on Lamb wave propagation. The plate has been analysed numerically and experimentally. Numerical calculations have been carried out by the use of the time-domain spectral finite element method, while for the experimental analysis laser scanning Doppler vibrometry (LSDV) has been utilised. The panel has been excited...
-
Analiza konstrukcji ramy nośnej wyczynowego roweru wodnego Rektor na przykładzie wybranego węzła
PublicationW pracy poruszono problem zmniejszenia masy wyczynowego roweru wodnego Rektor bez utraty jego wytrzymałości. W tym celu przeprowadzone zostały wieloetapowe obliczenia wybra- nego węzła konstrukcyjnego. Ponadto omówiono technologię wykonania rur kompozytowych. Podczas analizy sprawdzono trzy przypadki różniące się materiałem, z którego wykonano ramę, odpowiednio: z aluminium, laminatu zbrojonego włóknem szklanym oraz laminatu zbrojonego...
-
Study on Dry Sliding Wear and Friction Behaviour of Al7068/Si3N4/BN Hybrid Composites
PublicationHybrid aluminium metal matrix composites have the potential to replace single reinforced aluminium metal matrix composites due to improved properties. Moreover, tribological performance is critical for these composites, as they have extensive application areas, such as the automotive, aerospace, marine and defence industries. The present work aims to establish the tribological characteristics of Al7068/Si3N4/BN hybrid metal matrix...
-
Types of Surface Impurities versus the Quality of Brazed Joints
PublicationBrazing is one of the primary joining processes increasingly often applied in industry. Because of their mechanical properties, overlap joints are particularly popular when making brazed structures. The use of brazed joints in structures of critical importance requires that particular attention be paid to joint quality, e.g. by the appropriate cleaning of surfaces to be joined. The article presents results of non-destructive tests...
-
A review of applications of ellipsometry in corrosion research
PublicationElipsometria jest to nieinwazyjna i bardzo dokładna technika pomiarowa znajdująca coraz więcej zastosowań w badaniach korozyjnych. Poglądowo przedstawiono aktualne zastosowania pomiarów elipsometrycznych. Przeglądu dokonano pod kątem przydatności elipsometrii do wyznaczania grubości oraz charakterystyki optycznej cienkich warstewek pasywnych pokrywających powierzchnię różnych metali. Opisano zastosowanie pomiarów elipsometrycznych...
-
Zastosowania pomiarów elipsometrycznych w badaniach korozyjnych
PublicationElipsometria jest to nieinwazyjna i bardzo dokładna technika pomiarowa znajdująca coraz więcej zastosowań w badaniach korozyjnych. Poglądowo przedstawiono aktualne zastosowania pomiarów elipsometrycznych. Przeglądu dokonano pod kątem przydatności elipsometrii do wyznaczania grubości oraz charakterystyki optycznej cienkich warstewek pasywnych pokrywających powierzchnię różnych metali. Opisano zastosowanie pomiarów elipsometrycznych...
-
Experimentation, material modelling and simulation of bonded joints with a flexible adhesive
PublicationThe paper deals with material parameters identification of a flexible adhesive and the numerical simulation of its behaviour in a single lap bonded joint. The material modelling was based on the simple shear and tensile-shear laboratory tests of the bonded joints made of thin aluminium and polyurethane plates with the flexible adhesive Terostat MS 9360 manufactured by Henkel AG & Co. The adhesive was considered as a hyperelastic...
-
The influence of applying supplementary web plates on structural joint moment resistance and rotational stiffness
PublicationContinual trend to simplify structural elements and find less time-consuming solutions on construction site as well as inevitable increase in labour costs determine for instance elimination of those technological steps that are difficult to automation. Welding additional reinforcements and web stiffeners is a great example of such a step. The method presented in EN 1993-1-8 [8] is a result of long-term studies focused on calculating...
-
A pilot study to assess an in-process inspection method for small diameter holes produced by Direct Metal Laser Sintering
PublicationPurpose The purpose of this research is to evaluate the geometric quality of small diameter holes in parts printed by DMLS technology. An in-process optical inspection method is proposed and assessed during a pilot study. The influence of the theoretical hole diameter assumed in a CAD system and the sample thickness (hole length) on the hole clearance was analysed. Design/methodology/approach The samples made of two different...
-
Właściwości materiałów łożyskowych stosowanych w łożyskach ślizgowych okrętowych linii wałów.
PublicationOmówiono problematykę właściwości licznej grupy materiałów łożyskowych metalowych i niemetalowych, stosowanych w łożyskach ślizgowych okrętowych linii wałów. Określono wymagania dla tych materiałów oraz omówiono warunki pracy łożysk ślizgowych. Podano krótkie charakterystyki najczęściej stosowanych materiałów tzn. białych metali cynowych, białych metali ołowiowych, białych metali kadmowych, brązów, mosiądzów, stopów aluminium,...
-
Underwater in situ local heat treatment by additional stitches for improving the weldability of steel
PublicationIn this paper the influence of in situ local heat treatment performed by additional stitches on the weldability of high-strength low-alloy (HSLA) S355J2C+N steel was tested. The investigated steel is characterized by high susceptibility to cold cracking. It is necessary to find a method to improve the quality of welded joints. The local heat treatment was applied as an eect of bead-on plate welding made on the face of a Tekken...
-
Metallurgical characterization and high-temperature tensile failure of Inconel 617 alloy welded by GTAW and SMAW—a comparative study
PublicationTwo types of the weld joint of Inconel 617 alloy were produced using gas tungsten arc welding (GTAW) and shielded metal arc welding (SMAW) processes with ERNiCrCoMo-1 filler metal and ENiCrCoMo-1 electrode, respectively. The weld metal showed the segregation of the principle alloying elements like Mo and Cr along the inter-dendritic spaces, triggering the formation of secondary phases. The microstructure characterization of the...
-
Sessile droplet contact angle of water–Al2O3, water–TiO2 and water–Cu nanofluids
PublicationThis work presents measurements of the contact angle of sessile droplets for three nanofluids, i.e. water–Al2O3, water–TiO2 and water–Cu. The plates made of glass, anodized aluminium and stainless steel of different roughness served as substrates. Ultrasonic vibration was used for 30–60 min in order to stabilise the dispersion of the nanoparticles. Nanoparticles were tested at the concentration of 0.01%, 0.1%, and 1% by weight....
-
ZASTOSOWANIE ZGRZEWANIA WYBUCHOWEGO DO WYTWARZANIA KOMPOZYTÓW METALOWYCH O OSNOWIE ALUMINIOWEJ
PublicationEnergia wybuchu może zostać wykorzystana do realizacji wielu procesów technologicznych, m.in. wytwarzania złączy zgrzewanych, prasowania proszków, tłoczenia, odprężania i utwardzania metali. Bardzo interesującym zastosowaniem technologii zgrzewania wybuchowego jest wytwarzanie kompozytów metalowych. W artykule scharakteryzowano kompozyty metalowe i zgrzewanie wybuchowe jako jedną z metod ich otrzymywania. Przedstawiono autorską...
-
Kompozyt metalowy zgrzewany wybuchowo Zastosowanie zgrzewania wybuchowego do wytwarzania kompozytów metalowych o osnowie aluminiowej
PublicationEnergia wybuchu może zostać wykorzystana do realizacji wielu procesów technologicznych, m.in. wytwarzania złączy zgrzewanych, prasowania proszków, tłoczenia, odprężania i utwardzania metali. Bardzo interesującym zastosowaniem technologii zgrzewania wybuchowego jest wytwarzanie kompozytów metalowych. W artykule scharakteryzowano kompozyty metalowe i zgrzewanie wybuchowe jako jedną z metod ich otrzymywania. Przedstawiono autorską...
-
Wpływ odkształcenia na parametry stereometryczne powłok z faz międzymetalicznych NiAl i Ni3Al = Strain intensity effect on stereometrical properties at the NiAl i Ni3Al coating
PublicationWspółcześnie materiały na osnowie faz międzymetalicznych są przedmiotem badań wielu ośrodków naukowo-badawczych w kraju.Stopy na osnowie uporządkowanych faz międzymetalicznych z udziałem aluminium posiadają dużą odporność na utlenianie i korozję wżerową, a także wysoką wytrzymałość zmęczeniową oraz żaroodporność. Dlatego znalazły one zastosowanie do produkcji części maszyn do pracy w trudnych warunkach eksploatacyjnych (łopatki...
-
Detection of corrosion process in marine environment by means of acoustic emission technique
PublicationW pracy przedstawiono możliwość detekcji procesu korozyjnego nieniszczącą metodą emisji akustycznej konstrukcji metalowych pracujących w środowisku wody morskiej. Pewną alternatywą wobec technik elektrochemicznych w monitorowaniu korozji zaproponowano nieniszczącą technikę emisji akustycznej. Emisja akustyczna znana jako zjawisko fizyczne i technika pomiarowa znalazły zastosowanie w detekcji korozji obiektów morskich. W związku...
-
Hydrogen embrittlement of X2CrNiMoCuN25-6-3 super duplex stainless steel welded joints under cathodic protection
PublicationThe effect of cathodic polarization conditions on hydrogen degradation of X2CrNiMoCuN25-6-3 super duplex stainless steel welded joints, obtained using flux cored arc and submerged arc welding methods, was evaluated. Slow strain rate tensile tests of base material and welded specimens, ferrite content measurements, scanning electron microscopy observations, and statistical analysis were performed. It was found that hydrogenation...
-
Study on Microstructure-Property Relationship of Inconel 617 Alloy/304L SS Steel Dissimilar Welds Joint
PublicationWelding of Inconel 617 (IN617) alloy and austenitic 304L SS steel has been attempted using the autogenous Laser Beam Welding (LBW) process. Characterization of dissimilar weldments was performed on either side of the fusion boundaries. The metallographic results showed that the inhomogeneous microstructure formation for weld metal contained columnar and cellular dendrites near the interface, whilst the columnar, cellular and equiaxed...
-
Influence of the ionic strength on the amyloid fibrillogenesis of hen egg white lysozyme
PublicationThe study investigates the role of the electrostatic interactions in the fibrillation of the hen egg white lysozyme (HEWL). In order to achieve this aim the influence of the cations Na+, Mg2+ and Al3+ on the amyloid fibril formation and amorphous aggregation was tested. The amyloids are formed in the solution without added salt but the Thioflavin T fluorescence gives the false-negative result. In these conditions, the HEWL fibrils...
-
Eksploatacja napędów hydraulicznych w niskich temperaturach otoczenia Część II. Badania eksperymentalne rozruchu pomp i silników metodą termiczną
PublicationZasadniczym czynnikiem konstrukcyjnym, decydującym o dopuszczalnych parametrach zasilania oziębionych zespołów hydraulicznych w warunkach szoku termicznego, jest luz efektywny. Na jego zmianę wpływa wiele czynników: wartość luzu początkowego, temperatura początkowa zespołu, temperatura dopływającego oleju, natężenie przepływu, materiały z jakich są wykonane elementy zespołu, konstrukcja zespołu. Na podstawie uzyskanych przebiegów...
-
Fractal dimension for bending–torsion fatigue fracture characterisation
PublicationFracture surfaces after biaxial fatigue tests were compared using fractal dimension for three types of metallic materials in smooth and notched specimens made of S355J2 and 10HNAP steels and 2017-T4 aluminium alloy, considering both proportional and nonproportional cyclic loading. High-resolution optical 3D measurement studies were performed on the entire fracture surface. A direct correlation between fractal dimension and fatigue...
-
A study of jet impingement cooling enhancement by concave and convex heat sink shape modifications
PublicationThe rising demand for efficient cooling technologies is a strong driver of extensive research in this area. This trend is particularly strong in turbines and microprocessors technology. Presented study is focused on the jet impingement cooling concept, which is used in various configurations for many years. The potential of the heat sink shape modification is not yet fully explored. Available literature suggests that average Nusselt...
-
Wpływ mechanicznych naprężeń statystycznych i dynamicznych na trwałość i właściwości antykorozyjne warstw pasywnych.
PublicationBadania procesu pękania korozyjnego głównie skupiają się na długotrwałych badaniach niszczących, które wymagają zaangażowania wysokich kosztów związanych z wykorzystaniem aparatury badawczej oraz z jej obsługą techniczną. Opierając się na modelu pękania warstw pasywnych w którym czynnikiem wpływającym na proces inicjacji pękania korozyjnego jest pękanie warstwy pasywnej, wykonano badania właściwości mechanicznych warstw pasywnych...
-
Jeffreys heat conduction in coupled semispaces subjected to interfacial heating
PublicationA Jeffreys heat conduction problem for coupled semispaces subjected to the action of an interfacial heat source was defined. An analytical solution of the problem was derived for a polynomial specific power of the heat source using the Laplace transform approach. The asymptotic and parametric analysis was performed for different ratios of thermal conductivities , thermal diffusivities , thermal relaxation times and coefficients...
-
Opracowanie technologii spawania naprawczego szyn poddźwigowych A120 oraz badania nieniszczące jakości szyn w DCT w Porcie Północnym
PublicationEkspertyza dotyczy realizacji zlecenia związanego z naprawą spoin szyn poddźwigowych na terenie terminalu kontenerowego - Deep Water Terminal (DCT) w Porcie Północnym w Gdańsku. W ramach opracowania: 1. Wykonano badania ultradźwiękowe (UT) i magnetyczno-proszkowe (MT) spoin czołowych szyn poddźwigowych typu A120, według schematu dostarczonego przez firmę SKANSKA S.A. 2. Wykonano analizę wyników badań...
-
Localized impedance measurements of AA2024 and AA2024-T3 performed by means of AFM in contact mode
PublicationPurpose: The purpose of this paper is to present the results of an atomic force microscopy (AFM) based approach to local impedance spectroscopy (LIS) measurement performed on AA2024 and AA2024-T3 aluminium alloys. Design/methodology/approach: AFM-LIS measurements were performed ex-situ without the electrolyte environment, so in fact the electrical not electrochemical impedance was obtained. Findings: Relative local impedance values...
-
Analysis of the Environmental Impact of the Hull Construction of a Small Vessel Based on LCA
PublicationIn recent years, issues related to the impact of human activity on the natural environment have become pressing, and the challenge of global warming necessitates immediate action. To support environmental protection efforts, it has become imperative to adopt a broader perspective when evaluating various products and systems. A valuable tool for such assessments is a life cycle assessment (LCA), which enables a comprehensive analysis...
-
The effect of pre-hydrogen charging on corrosion behaviour of superduplex stainless steel welded joints
PublicationThe paper presents results of research undertaken to determine the influence of hydrogen on passivity and corrosion resistance of 2507 super duplex stainless steel welded joints. Butt welded joints were made with low heat input using flux corded arc welding (FCAW) method. Coupons of 5.0 x 5.0 mm were cut from the welded joints containing weld metal (WM), heat affected zone (HAZ) and parent metal (PM). Hydrogen was introduced...
-
Effect of Pin Shape on Thermal History of Aluminum-Steel Friction Stir Welded Joint: Computational Fluid Dynamic Modeling and Validation
PublicationThis article studied the effects of pin angle on heat generation and temperature distribution during friction stir welding (FSW) of AA1100 aluminum alloy and St-14 low carbon steel. A validated computational fluid dynamics (CFD) model was implemented to simulate the FSW process. Scanning electron microscopy (SEM) was employed in order to investigate internal materials’ flow. Simulation results revealed that the mechanical work...
-
Experimental and numerical investigations of ultimate strength of imperfect stiffened plates of different slenderness
PublicationThe objective of this study is to analyse the behaviour of compressed stiffened plates of different slenderness using experimental and numerical methods. The presented results are part of a long-term project to investigate the ultimate strength of geometrically imperfect structures subjected to different degradation phenomena, including corrosion degradation and locked cracks. Several specimens were subjected to a uniaxial compressive...
-
Trwałość spawanych instalacji wodnych wykonanych z nierdzewnych stali austenitycznych
PublicationW artykule przedstawiono dwa przypadki przedwczesnych uszkodzeń spawanych instalacji wodnych wykonanych ze stali odpornych na korozję. W celu ustalenia przyczyn uszkodzenia instalacji przeprowadzono badania metalograficzne, makro - i mikroskopowe oraz mikroanalizę składu chemicznego EDS na próbkach pobranych z reprezentatywnych miejsc. Wykazano, że głównymi przyczynami awarii rurociągów wody pitnej były niezgodności spawalnicze,...
-
Storing Matter’technique in SIMS depth profile analysis
PublicationSecondary ion mass spectrometry (SIMS) is a very useful technique for the analysis of layered systems. It is based on the primary ion beam sputtering of solids and mass analysis of the emitted secondary ions. A main limitation of this technique results from the direct quantitative analysis, since the ionization efficiency of a given atom is highly influenced by the neighbouring atoms at the surface. This phenomenon is known as...
-
Recovery and re-use of photovoltaic solar cells from crystalline silicon
PublicationCrystalline silicon-type PV modules consist, in order of mass, of glass, an aluminium frame, an EVA coating, solar cells, a terminal box, back film and tapping screws. From the economic point of view, pure silicon, recoverable from spent cells, is the most important material owing to its cost and shortage. For crystalline, silicon-based PV cells, the following chemical treatments were performed: removal of the metal coating, followed...
-
Rigid polyurethane foams modified with selected layered silicate nanofillers
PublicationThe aim of this study was to investigate the effect of three different nanofillers on the properties of rigid polyurethane foams, which were prepared by a one-step, laboratory-scale method from a two-component system at the ratio of NCO groups to OH groups equaled to 2. The reaction mixture consisted of the proper amounts of the commercial oligoether polyol, catalysts, water, nanoclays, and polymeric diphenylmethane diisocyanate....
-
Progress in the post weld residual stress evaluation using Barkhausen effect meter with a novel rotating magnetic field probe
PublicationWe report the progress in post weld residual stress evaluation using Barkhausen effect (BE) meter with rotating magnetic field probe. The novel probe of the BE meter contains two C-core electromagnets and searching coil with ferrite antenna. This meter allows automatic measurements of BE intensity envelopes at different angles of magnetizing field. The full process of measurement at given position of the probe takes about only...
-
Perfect thermal contact of hyperbolic conduction semispaces with an interfacial heat source
PublicationThe problem of thermal contact between two bodies with a heat source at their interface presents great scientific and practical interest. On the time scale of a nanosecond or shorter, heat propagation should be considered in the form of thermal waves of finite speeds. This study investigated the thermal behaviour of hyperbolic conduction semispaces in perfect thermal contact subjected to the action of an interfacial heat source....
-
New matrix-free reference material for ethene in the form of optical fibres
PublicationReference materials are indispensable in the qualitycontrol and quality assurance of analytical measurements. Onenovel approach to the generation of standard gaseous mixturesof toxic, reactive, volatile, labile, and malodorous substancesinvolves thermal decomposition or rearrangement, under definedtemperature conditions, of compounds immobilized, bychemical bonding, on the surface of an appropriate carrier torelease specific amounts...
-
High frequency dynamics of an isotropic Timoshenko periodic beam by the use of the Time-domain Spectral Finite Element Method
PublicationIn this work results of numerical simulations and experimental measurements related to the high frequency dynamics of an aluminium Timoshenko periodic beam are presented. It was assumed by the authors that the source of beam structural periodicity comes from periodical alterations to its geometry due to the presence of appropriately arranged drill-holes. As a consequence of these alterations dynamic characteristics of the beam...