Search
Search results for: TWO-PHASE CLOSED THERMOSIPHON
-
Plate heat exchanger with porous structure for potential use in ORC system
PublicationThe experimental analysis of passive heat transfer intensification in the case of plate heat exchanger has been carried out. The passive intensification was obtained by a modification of the heat transfer surface, which was covered by a metallic porous microlayer. The experiment was accomplished in two stages. In the first stage the commercial stainless steel gasketed plate heat exchanger was investigated, while in the second one...
-
Influence of metallic porous microlayer on pressure drop and heat transfer of stainless steel plate heat exchanger
PublicationThe experimental analysis of passive heat transfer intensification in the case of plate heat exchanger has been carried out. On the heat transfer surface of heat exchanger the metallic porous layer was created. The experiment was accomplished in two stages. In the first stage the commercial stainless steel gasketed plate heat exchanger was investigated, while in the second one – the identical heat exchanger but with the modified...
-
Fast surrogate-assisted simulation-driven design of compact microwave hybrid couplers
PublicationThis work presents a robust methodology for expedited simulation-driven design optimization of compact microwave hybrid couplers. The technique relies on problem decomposition, and a bot-tom–up design strategy, starting from the level of basic building blocks of the coupler, and finishing with a tuning procedure that exploits a fast surrogate model of the entire structure. The latter is constructed by cascading local response surface...
-
Introduction of Pro and Its Analogues in the Conserved P1 Position of Trypsin Inhibitor SFTI-1 Retains Its Inhibitory Activity
PublicationA number of monocyclic SFTI-1 analogues modified in the conserved inhibitor P1 position by Pro, its L-hydroxyproline (Hyp) derivative as well as mimetics with different ring size were synthesized by the solid-phase method. Replacement of Ser6 by Pro, Hyp, and a four-member ring, L-azetidine-2-carboxylic acid (Aze), retained trypsin or chymotrypsin inhibitory activity. The determined association equilibrium constants of these analogues...
-
A Wind Energy Conversion System Based on a Generator with Modulated Magnetic Flux
PublicationIn this work, the concept of an energy conversion system for wind turbines based on the modified permanent magnet synchronous generator (PMSG) is presented. In the generator, a pair of three-phase windings is used, one of which is connected in a “star” and the second in a “delta” configuration. At the outputs of both windings, two six-pulse uncontrolled (diode) rectifiers are included. These rectifiers are mutually coupled by a...
-
A study about daylighting knowledge and education in Europe. Results from the first phase of the DAYKE project
PublicationThis paper presents selected results from the first stage of DAYKE (Daylight Knowledge in Europe), a 3- phase project that investigates the knowledge on daylighting in buildings among architecture students and practitioners across Europe. Subjective judgements from 561 students from 8 architecture universities in the EU, collected through two surveys in 2018. The key findings are: (i) the spatial distribution of comfort and mood...
-
A comprehensive approach to SBR modelling for monitoring and control system design
PublicationThe aim of this research is to provide a comprehensive description of the Sequencing Batch Reactor (SBR) modelling for monitoring, control, and plant operational optimisation validation. The paper provides a detailed modelling of the SBR, its components and constituent processes. For this purpose, the mass balance principle and continuity equations were provided with a reactive term implemented using Activated Sludge Model (ASM)....
-
Application of additional factors supporting the microextraction process
PublicationDue to the fact that green analytical chemistry is of high importance, the past two decades have witnessed a rapid growth in the sample preparation area with special emphasis on simplification, miniaturization and automation of extraction procedures. In addition, to accelerate the extraction processes and to improve the separation of analytes, several enhanced parameters are applied. These factors include, ultrasounds, microwaves,...
-
Two-dimensional simulations of concrete fracture at aggregate level with cohesive elements based on X-ray lCT images
PublicationThe paper presents results of two-dimensional meso-scale simulations of fracture in notched concrete beams subjected to three-point bending test. Concrete was assumed as a 4-phase material composed of aggregate grains placed in the cement matrix, interfacial transitional zones (ITZs) and macro-voids. The particle distribution was taken from real concrete beams on the basis of X-ray lCT images. Comprehensive numerical analyses were carried...
-
Corporate Social Responsibility Culture in the University of Technology – Polish Students Perspective
PublicationPurpose: The view on CSR concept is constantly broadening and still the new perspective is needed. New challenges are imposed by social, environmental and economic changes. A stakeholder approach defining organizations’ responsibility is no more valid. There is a need to redefine CSR concept and its role in sustainable development. Higher education and its role in shaping future attitudes towards corporate social responsibility...
-
Closed Form Constraint Equations Used to Express Frictionless Slip of Multibody Systems Attached to Finite Elements—Application to a Contact between a Double Pendulum and a Beam
PublicationThis paper focuses on the numerical modeling of the dynamics of mechanical systems. Robots that can inspect high-voltage lines inspired this research. Their control systems must anticipate potential grab positions appropriately. We intend to formulate equations dedicated to the numerical description of the robot/cable contact. The investigated problem is not straightforward, since parts of the modeled systems are numerically inhomogeneous....
-
Forced vibrations in a dynamic system that is damped by a mechanism that trans-pass through its singular position
PublicationIn the paper, vibrations of a hybrid multibody-continuous system are investigated. For all the mechanical devices, effective damping methods are crucial in the design process. To obtain it, installation of viscous dampers or elasto-viscous elements is dominant. In the paper, an alternative method is investigated. It is based on modal disparity. To describe the method briefly, when structural damping is present in continuous systems,...
-
Structure-Property Relationship and Multiple Processing Studies of Novel Bio-Based Thermoplastic Polyurethane Elastomers
PublicationCurrently, the growing demand for polymeric materials has led to an increased need to develop effective recycling methods. This study focuses on the multiple processing of bio-based thermoplastic polyurethane elastomers (bio-TPUs) as a sustainable approach for polymeric waste management through mechanical recycling. The main objective is to investigate the influence of two reprocessing cycles on selected properties of bio-TPUs....
-
Comprehensive thermodynamic analysis of steam storage in a steam cycle in a different regime of work: A zero-dimensional and three-dimensional approach
PublicationDue to the current trends aiming to reduce carbon dioxide emissions by increasing the use of renewable energy sources, changes are required in the operation of coal-fired steam units. The unstable nature of renewable energy sources, depending on weather conditions, means that the amount of energy produced varies and is not always in line with peak demand. To ensure the security and stability of energy supplies in the energy system,...
-
Diamond-Based Supercapacitors with Ultrahigh Cyclic Stability Through Dual-Phase MnO2-Graphitic Transformation Induced by High-Dose Mn-Ion Implantation
PublicationWhile occasionally being able to charge and dischargemore quickly than batteries, carbon-based electrochemical supercapacitors(SCs) are nevertheless limited by their simplicity of processing, adjustableporosity, and lack of electrocatalytic active sites for a range of redox reactions.Even SCs based on the most stable form of carbon (sp3carbon/diamond)have a poor energy density and inadequate capacitance retention during longcharge/discharge...
-
Solubility of carbon dioxide in water: Some useful results for hydrate nucleation
PublicationIn this paper, the solubility of carbon dioxide (CO2) in water along the isobar of 400 bar is determined by computer simulations using the well-known TIP4P/Ice force field for water and the TraPPE model for CO2. In particular, the solubility of CO2 in water when in contact with the CO2 liquid phase and the solubility of CO2 in water when in contact with the hydrate have been determined. The solubility of CO2 in a liquid–liquid...
-
DEPO: A dynamic energy‐performance optimizer tool for automatic power capping for energy efficient high‐performance computing
PublicationIn the article we propose an automatic power capping software tool DEPO that allows one to perform runtime optimization of performance and energy related metrics. For an assumed application model with an initialization phase followed by a running phase with uniform compute and memory intensity, the tool performs automatic tuning engaging one of the two exploration algorithms—linear search (LS) and golden section search (GSS), finds...
-
Effect of different crystalline structures on W/O and O/W/O wax emulsion stability
PublicationtThe possibility of emulsion stabilization using mineral and vegetable wax particles only (without sur-factant) was investigated. Mineral waxes, paraffin wax and ceresin, and a vegetable wax, carnauba wax,were used. The content of the wax particles and the water to oil proportion were found crucial for thestability of all emulsions. Some emulsions were also produced with a liquid wax (i.e. jojoba oil). Themultiple light scattering...
-
Analysis of IMS/NGN call processing performance using phase-type distributions
PublicationThis work is a continuation of our research on the traffic model dedicated for design and analysis of the Next Generation Network (NGN), which is standardized for distribution of current and future multimedia services based on the IP Multimedia Subsystem (IMS). Our analytical and simulation models allow evaluation of mean Call Set-up Delay E(CSD) as well as mean Call Disengagement Delay E(CDD) in a single domain of IMS/NGN. Ensuring...
-
Mechanical exfoliation and layer number identification of single crystal monoclinic CrCl3
PublicationAfter the recent finding that CrI3, displays ferromagnetic order down to its monolayer, extensive studies have followed to pursue new two-dimensional (2D) magnetic materials. In this article, we report on the growth of single crystal CrCl3 in the layered monoclinic phase. The system after mechanical exfoliation exhibits stability in ambient air (the degradation occurs on a time scale at least four orders of magnitude longer than...
-
A rapid dispersive liquid–liquid microextraction of antimicrobial onion organosulfur compounds in animal feed coupled to gas chromatography-mass spectrometry
PublicationA rapid analytical procedure is proposed for determining two antimicrobial onion organosulfur compounds, propyl disulfide (PDS) and propyl propane thiosulfonate (PTSO), in animal feed. The use of PTSO as a natural ingredient in animal feed is allowed due to its antimicrobial activity against pathogenic organisms. Two analytical methodologies using gas chromatography coupled to mass spectrometry (GC-MS) are compared. After the extraction...
-
Subjective Quality Evaluation of Underground BPL-PLC Voice Communication System
PublicationDesigning a reliable voice transmission system is not a trivial task. Wired media, thanks to their resistance to mechanical damage, seem an ideal solution. The BPL-PLC (Broadband over Power Line – Power Line Communication) cable is resilient to electricity stoppage and partial damage of phase conductors. It maintains continuity of transmission in case of an emergency situation, including paramedic rescue operations. These features...
-
General concept of reduction process for big data obtained by interferometric methods
PublicationInterferometric sonar systems apply the phase content of the sonar signal to measure the angle of a wave front returned from the seafloor or from a target. It collect a big data – datasets that are so large or complex that traditional data processing application software is inadequate to deal with them. The recording a large number of data is associated with the difficulty of their efficient use. So data have to be reduced. The main...
-
Sensorless Field Oriented Control of Five Phase Induction Motor with Third Harmonic Injection
PublicationIn this paper, a sensorless field oriented control system of five-phase induction machine with the 3rd harmonic rotor flux is presented. Two vector models, α1-β1 and α3-β3, were transformed into d1-q1, d3-q3 models oriented in rotating frames, which correspond to the 1st and 3rd harmonic plane respectively. The authors proposed the linearization of the model in d-q coordinate frames by introducing a new variable “x” which is proportional...
-
Effect of free water on the quasi‑static compression behavior of partially‑saturated concrete with a fully coupled DEM/CFD approach.
PublicationThe work aims to numerically investigate the quasi-static response of partially fluid-saturated concrete under two-dimensional uniaxial compression at the mesoscale. We investigated how the impact of free pore fluid content (water and gas) affected the quasi-static strength of concrete. The totally and partially fluid-saturated concrete behavior was simulated using an improved pore-scale hydro-mechanical model based on DEM/CFD....
-
The structure of Bi2VO5.5 ceramic prepared by 3 different ways measured with X-ray diffraction
Open Research DataThe structure of Bi2VO5.5 ceramics was measured by XRD.
-
Transient modeling in common DC link of power converters
PublicationПредмет исследования. Представлена математическая модель силовых преобразователей электропривода, питающихся от общего звена постоянного тока, на примере тяговых электроприводов карьерного самосвала БЕЛАЗ-90 мощностью 280 кВт. Модель выполнена в пакете MATLAB/Simulink. Новизна предложенной модели заключается в применении новой топологии силовой схемы для исследования работы двух инверторов, под- ключенных к одному звену постоянного...
-
Analysis of exhaled breath for dengue disease detection by low-cost electronic nose system
PublicationThis paper presents a procedure and a set-up of an electronic nose system analyzing exhaled breath to detect the patients suffering from dengue – a mosquito-borne tropical disease. Low-power resistive gas sensors (MiCS-6814, TGS8100) were used to detect volatile organic compounds (VOCs) in the exhaled breath. The end-tidal phase of patients exhaled breath was collected with a BioVOCTM breath sampler. Two strategies were assessed...
-
Spetiation of organic matter in Vertical Flow Constructed Wetlands
PublicationThe object of the research were VFCWs which are a component of biological treatment of two hybrid hydrophyte systems located in Wieszyno and Wiklino, close to Słupsk, Poland. The facilities that are subject to analyses are unified in terms of structure (filtration material, depth of the bed and time of operation), but they differ in organic matter load, amounting respectively to: 8.0 gCOD/m2day and 31.0 gCOD/m2day.The intensity...
-
Extension management of a knowledge base migration process to IPv6
PublicationThere are many reasons to deploy IPv6 protocol with IPv4 address space depletion being the most indisputable. Unfortunately, migration to IPv6 protocol seems slower than anticipated. To improve pace of the IPv6 deployment, authors of the article developed the two applications that supports the migration process. Their main purpose is to help less experienced network administrators facilitate the migration process with a particular...
-
Steady-State Vibration Level Measurement of the Five-Phase Induction Machine during Third Harmonic Injection or Open-Phase Faults
PublicationMultiphase electric machines are increasingly used in various industries and for electromobility. Complex systems have been developed for the control and powering of multiphase machines, which require verification. The quality of control and the power supply of electric machines is usually evaluated by analyzing various electrical parameters. On the other hand, taking into account the fact that a motor is an electrical-mechanical...
-
Modelling of heat transfer during flow condensation of natural refrigerants under conditions of increased saturation pressure
PublicationThe paper presents a modified in-house model for calculating heat transfer coefficients during flow condensation, which can be applied to a variety of working fluids, but natural refrigerants in particular, at full range thermodynamic parameters with a particular focus on increased saturation pressure. The modified model is based on a strong physical basis, namely the hypothesis of analogy between the heat transfer coefficient...
-
Analysis of chiral pharmaceutical residues in influent and effluent samples at racemic and enantiomeric level using liquid chromatography-tandem mass spectrometry
PublicationIn this work, two different chromatographic methods for seasonal monitoring of pharmaceutical residue in wastewater samples were developed. In the case of enantiomeric separation of selected compounds, LC-MS technique combining with vancomycin based chiral stationary phase was used. The performance of chiral analysis enabled to monitor the pharmaceutical contamination at the enantiomeric level. The d-SPE procedure was developed...
-
Analysis of electromagnetic disturbances in DC network of grid connected building-integrated photovoltaic system
PublicationThis paper focuses on conducted electromagnetic interference (EMI) emissions and propagation in the DC network of grid connected building integrated photovoltaic (PV) system. The investigated PV system, consists of ten solar panels, cabling and the grid-connected one phase inverter. The EMI simulation model of the real PV system has been developed with the aid of impedance analyzer measurements of solar panels and the DC network...
-
Numerical investigations of discrete crack propagation in Montevideo splitting test using cohesive elements and real concrete micro-structure
PublicationThe paper is aimed at accurately predicting the discrete fracture process in concrete specimens under complex stress states in two dimensional (2D) simulations. Plain concrete specimens subjected to Montevideo splitting test (MVD) were used for consideration due to non-negligible shear stresses impact in this type of test. In order to reflect the heterogeneous nature of the concrete, the meso-structure of the samples was included...
-
Problems and challenges associated with estimating the emissions of organic compounds from indoor materials
PublicationFor several years intensive research has been carried out with the aim of developing a database of the types and amounts of pollutants released from indoor materials to the indoor environment. The paper discusses in detail basic problems and challenges encountered when estimating the emissions of chemical compounds released from of indoor materials. Factors affecting the validity of data obtained by using two different types of...
-
Modal analysis of railway current collectors using Autodesk Inventor
PublicationThe paper presents the results of modal analysis of railway current collector type 160EC. In the first place, the analysis was carried out analytically for a simplified two lumped mass pantograph model. Then numerical analysis was conducted in the Autodesk Inventor (AI) on the prepared multibody model using the AI modal analysis algorithm, which is based on the finite element method (FEM). Model elements which are most relevant...
-
Influence of metallic porous microlayer on pressure drop and heat transfer of stainless steel plate heat exchanger
PublicationThe experimental analysis of passive heat transfer intensification in the case of plate heat exchanger has been carried out. The metallic porous layer was created on the heat transfer surface of analyzed unit. The experiment was accomplished in two stages. In the first stage the commercial stainless steel gasketed plate heat exchanger was investigated, while in the second one – the identical heat exchanger but with the modified...
-
Simulation of the weight averaging of pulse frequency modulated sensor output signal
Open Research DataThe aim of the research is investigation of the efficiency of weight averaging of pulse frequency modulated signal. It was shown that from the point of view of the reduction of the sampling error the best are polynomial weighing functions, for which the maximum of this component error decreases proportionally to the appropriate power of the number of...
-
Physicochemical properties of Mn1.45Co1.45Cu0.1O4 spinel coating deposited on the Crofer 22 H ferritic steel and exposed to high-temperature oxidation under thermal cycling conditions
PublicationThe Crofer 22 H ferritic steel substrate was coated with an Mn1.45Co1.45Cu0.1O4 spinel by means of electrophoresis. After high-temperature oxidation under thermal cycling conditions, the physicochemical properties of the obtained system were evaluated. During 48-h cycles that involved heating the samples up to temperatures of either 750 or 800 °C, the oxidation kinetics of both coated and unmodified steel approximately obeyed...
-
EVALUATION OF LIQUID-GAS FLOW IN PIPELINE USING GAMMA-RAY ABSORPTION TECHNIQUE AND ADVANCED SIGNAL PROCESSING
PublicationLiquid-gas flows in pipelines appear in many industrial processes, e.g. in the nuclear, mining, and oil industry. The gamma-absorption technique is one of the methods that can be successfully applied to study such flows. This paper presents the use of thegamma-absorption method to determine the water-air flow parameters in a horizontal pipeline. Three flow types were studied in this work: plug, transitional plug-bubble,...
-
Stationary underwater channel experiment: Acoustic measurements and characteristics in the Bornholm area for model validations
PublicationThe underwater acoustical channel is time-variant, and even on small time scales there is often existing no ‘acoustical frozen ocean’. Popular is the use of WSSUS-channel transmission modeling (Wide-Sense Stationary Uncorrelated Scattering) for the stochastic description of bandpass signals in GSM mobile phones with moving participants; since this results in a halved number of model parameters. For underwater sound applications...
-
Lanthanide ions (Eu3+, Er3+, Pr3+) as luminescence and charge carrier centers in Sr2TiO4
PublicationA series of strontium orthotitanate (Sr2TiO4) samples doped with 2% of a mole of europium, praseodymium, and erbium were obtained using the solid-state synthesis method. The X-ray diffraction (XRD) technique confirms the phase purity of all samples and the lack of the influence of dopants at a given concentration on the structure of materials. The optical properties indicate, in the case of Sr2TiO4:Eu3+, two independent emission...
-
Dysfunctional prefrontal cortical network activity and interactions following cannabinoid receptor activation.
PublicationCoordinated activity spanning anatomically distributed neuronal networks underpins cognition and mediates limbic-cortical interactions during learning, memory, and decision-making. We used CP55940, a potent agonist of brain cannabinoid receptors known to disrupt coordinated activity in hippocampus, to investigate the roles of network oscillations during hippocampal and medial prefrontal cortical (mPFC) interactions in rats. During...
-
Rotation Triggers Nucleotide-Independent Conformational Transition of the Empty β Subunit of F1-ATPase
PublicationF1-ATPase (F1) is the catalytic portion of ATP synthase, a rotary motor protein that couples proton gradients to ATP synthesis. Driven by a proton flux, the F1 asymmetric γ subunit undergoes a stepwise rotation inside the α3β3 headpiece and causes the β subunits’ binding sites to cycle between states of different affinity for nucleotides. These concerted transitions drive the synthesis of ATP from ADP and phosphate. Here, we study...
-
Polymeric metal‐containing ionic liquid sorbent coating for the determination of amines using headspace solid‐phase microextraction
PublicationThis study describes the design, synthesis, and application of polymeric ionic liquid sorbent coatings featuring nickel metal centers for the determination of volatile and semivolatile amines from water samples using headspace solidphase microextraction. The examined polymeric ionic liquid sorbent coatings were composed of two ionic liquid monomers (tetra(3-vinylimidazolium)nickel bis[(trifluoromethyl)sulfonyl]imide [Ni2+(VIM)4]...
-
The effect of metal cluster deposition route on structure and photocatalytic activity of mono- and bimetallic nanoparticles supported on TiO2 by radiolytic method
PublicationTiO2 (P25) was modified with small and relatively monodisperse mono- and bimetallic clusters (Ag, Pd, Pt, Ag/Pd, Ag/Pt and Pd/Pt) induced by radiolysis to improve its photocatalytic activity. The as-prepared samples were characterized by X-ray fluorescence spectrometry (XRF), photoluminescence spectrometry (PL), diffuse reflectance spectroscopy (DRS), X-ray powder diffractometry (XRD), scanning transition electron microscopy (STEM)...
-
The use of lightweight aggregate saturated with PCM as a temperature stabilizing material for road surfaces.
PublicationThis paper presents the possibility of adding lightweight building aggregates to increase the stability – mechanical as well as thermal - of constructions and road objects. This stability can be achieved through saturating the porous granules of aggregate with a phase-change material (PCM) that allows the accumulation of solar heat. Intense solar radiation, especially during the summer, can cause the asphalt on road surfaces, bridges...
-
From Scores to Predictions in Multi-Label Classification: Neural Thresholding Strategies
PublicationIn this paper, we propose a novel approach for obtaining predictions from per-class scores to improve the accuracy of multi-label classification systems. In a multi-label classification task, the expected output is a set of predicted labels per each testing sample. Typically, these predictions are calculated by implicit or explicit thresholding of per-class real-valued scores: classes with scores exceeding a given threshold value...
-
Conley-Morse graphs for a two-patch vaccination model
Open Research DataThis dataset contains selected results of rigorous numerical computations described in Section 5 of the paper "Rich bifurcation structure in a two-patch vaccination model" by D.H. Knipl, P. Pilarczyk, G. Röst, published in SIAM Journal on Applied Dynamical Systems (SIADS), Vol. 14, No. 2 (2015), pp. 980–1017, doi: 10.1137/140993934.