Filters
total: 1259
filtered: 1072
displaying 1000 best results Help
Search results for: VEHICULAR ROADS
-
Protection of bridges against stray current corrosion
PublicationA case study of Siennicki Bridge stray current corrosion hazard is presented. A corrosion risk was caused by incorrectly designed tram line traction which goes over the bridge. No dielectric insulation between running rails and bridge steel construction was used. A variety of protection methods against stray currents are described. Characteristics of the endangered bridge were described. Impressed current cathodic protection system...
-
Equivalent axle load factors for design of rigid pavements derived from fatigue criteria
PublicationArtykuł przedstawia określenie współczynników równoważności osi dla nawierzchni sztywnych na podstawie kryteriów zmęczeniowych stosowanych w mechanistyczno-empirycznej metodzie projektowania nawierzchni drogowych. Przedstawiono kryteria zmęczeniowe z wybranych metod projektowania i analizy nawierzchni sztywnych. Kryteria te zostały użyte do wyprowadzenia wzorów do obliczania współczynników równoważności obciążenia osi. Stwierdzono,...
-
Modelling of joining route segments of differential curvature
PublicationThe paper presents a new general method of modelling route segments curvature using differential equations. The method enables joining of route segments of different curvature. Transitional curves of linear and nonlinear curvatures have been identified in the case of joining two circular arcs by S-shaped and C-oval transitions. The obtained S-shaped curves have been compared to the cubic C-Bezier curves and to the Pythagorean hodograph...
-
The Impact of Long-Time Chemical Bonds in Mineral-Cement-Emulsion Mixtures on Stiffness Modulus
PublicationDeep cold in-place recycling is the most popular method of reuse of existing old and deteriorated asphalt layers of road pavements. In Poland, in most cases, the Mineral-Cement-Emulsion mixture technology is used, but there are also applications combining foamed bitumen and cement. Mineral-Cement-Emulsion mixtures contain two different binding agents – cement as well as asphalt from the asphalt emulsion. Asphalt creates asphalt...
-
Rebuilding Bailey Bridge to Bridge With Bascule Span – A Case Study
PublicationThe structural analysis of a road foldable prefabricated steel Bailey- type bridge located over the Tuga River in Żelichowo, Poland is performed in this paper. Interesting and untypical bridge redevelopment performed made it possible to lift the middle foldable bridge span by approximately 4.0 m concerning the existing state. The paper begins with a survey of literature carried out on the investigations of foldable Bailey-type...
-
Case Study of Old Steel Riveted Railway Truss Bridge: From Material Characterization to Structural Analysis
PublicationThe structural analysis of an old steel riveted railway truss bridge located over the Maruska River on the Działdowo – Olsztyn, Poland railway line is performed in this paper to check its behaviour under today’s railway loads. The mechanical properties of construction steel extracted from the old steel bridge are investigated by tensile tests, impact tests through the Charpy pendulum impact V-notch, and an optical emission spectrometer....
-
Limit States of Shallow Bridge Foundations With Sheet Piling Covers
Publication -
Laminated plates and shells - first ply failure analysis within 6-parameter shell theory
PublicationThis work describes Tsai-Wu and Hashin criteria modifications, dictated by nonlinear 6-parameter shell theory with asymmetric strain measures and drilling rotation. The material law is based on standard orthotropic elastic constants for a non-polar continuum, under plane state of stress. First ply failure loads of cylindrical panel subjected to pressure and flat compressed plate are estimated by means of Finite Element Analysis....
-
Selected problems of sensitivity and reliability of a jack-up platform
PublicationThe paper deals with sensitivity and reliability applications to numerical studies of an off-shore platform model. Structural parameters and sea conditions are referred to the Baltic jack-up drilling platform. The study aims at the influence of particular basic variables on static and dynamic response as well as the probability of failure due to water waves and wind loads. The paper presents the sensitivity approach to a generalized...
-
The impact of air humidity on the operation of proton exchange membrane fuel cells determined using dynamic electrochemical impedance spectroscopy
PublicationThis paper describes the changes in the fuel cell impedance across a range of current loads and humidity changes. The changes of each equivalent circuit parameters representing specific processes occurring in fuel cells, as a function of humidity and current changes, were determined. Within the combined scope of current and humidity, the optimal working conditions of the cells were determined, corresponding to the lowest impedance...
-
Reduction of noise and rolling resistance by horizontal grinding of asphalt pavements
PublicationGrinding of cement concrete pavements to reduce unevenness and noise is common since a long time. Grinding is then made with wheels equipped with diamond blades rotating in the vertical plane. This creates narrow vertical/longitudinal grooves in the pavement. It is not applied to asphalt pavements. In this paper an alternative type of grinding is studied. In this case plates with diamond heads rotate in the same plane as the pavement,...
-
an intelligent image processing sensor - the algorithm and the hardware implementation
PublicationW artykule przedstawiono algorytm przeznaczony do rozpoznawania obiektów ruchomych w obrazie do celu analizy ruchu pojazdów. Algorytm został zrealizowany w układzie FPGA.Ang.: This paper describes the idea and theimplementation of the robust algorithm dedicated toextraction of moving vehicles from real-time cameraimages for the evaluation of traffic parameters, suchas the number of vehicles, their direction of movementand their...
-
Comparison of low-temperature cracks intensity on pavements with high modulus asphalt concrete and conventional asphalt concrete bases
PublicationHigh modulus asphalt concrete (HMAC) base courses provide very good resistance to rutting and fatigue but they can increase the risk of low-temperature cracking as compared with conventional asphalt concrete (AC). The article presents the comparison of these two road materials in terms of low-temperature cracking. The statistical method based on the ordered logistic regression model was used. The analysis was based on results of...
-
Identification of safety hazards and their sources in tram transport
PublicationBoth in Poland and in most countries of the European Union, the tram infrastructure is extensively expanding. Contemporary low-floor trams are constructed according to different technical assumptions than typical railway vehicles or high floor trams. In Poland such vehicles rides often on lines designed according to standards developed to the classical vehicles. At the same time, the intensity of road traffic and the number of...
-
A Novel Spatio–Temporal Deep Learning Vehicle Turns Detection Scheme Using GPS-Only Data
PublicationWhether the computer is driving your car or you are, advanced driver assistance systems (ADAS) come into play on all levels, from weather monitoring to safety. These modern-day ADASs use various assisting tools for drivers to keep the journey safe; these sophisticated tools provide early signals of numerous events, such as road conditions, emerging traffic scenarios, and weather warnings. Many urban applications, such as car-sharing...
-
Badania czynników wpływających na bezpieczeństwo ruchu drogowego w województwach
PublicationWojewództwa stanowią podstawową jednostę zarządzania w Polsce. Jak dotąd mało rozpoznanym proble-mem są czynniki wpływające na bezpieczeństwo ruchu dro-gowego na poziomie województw. Na podstawie przeglądu literatury zidentyfikowano metody analiz bezpieczeństwa na poziomie regionanym a także niektóre czynniki wpływające na bezpieczeństwo ruchu na obszarze regionów. Następnie zebrano dane dostępne dla województw w Polsce w...
-
Static Series and Shunt-series PE Voltage-quality Controllers
PublicationAs presented in the Chap. 7 static shunt power electronics (PE) voltage-quality controllers protect the utility electrical system from the unfavorable impact of customer loads. Shunt controllers, as shown in Chap. 6, are recommended mainly for mitigation of the causes of disturbances, and not their effects in distanced nodes of a power-electronics system. In the case when reduction of disturbances effects is required, which leads...
-
The fate and contamination of trace metals in soils exposed to a railroad used by Diesel Multiple Units: Assessment of the railroad contribution with multi-tool source tracking
PublicationSoil samples from cut slopes from lightly loaded railway lines used by Diesel Multiple Units for 5 years in Gdansk (Poland) were collected and analyzed for trace metals (TMs): Zn, Pb, Cd, Ni, Cr, Cu, and Fe. The main aim was to assess soil enrichment, contamination status, and distribution of TMs relative to the distance from the railway track. Extensive source tracking analyses were performed using cluster analysis (CA) and the...
-
Ocena odporności na pękanie podbudów drogowych z mieszanek mineralno-cementowo-emulsyjnych (MCE)
PublicationPodbudowy z mieszanek mineralno-cementowo-emulsyjnych (MCE) są jednym z wielu materiałów stosowanych do wykonywania warstw nawierzchni w ramach przebudów dróg w Polsce. Mieszanki MCE pozwalają na maksymalne powtórne wykorzystanie istniejących warstw konstrukcyjnych do budowy lub przebudowy nawierzchni. Do wykonania podbudów z MCE stosuje się materiał pochodzący z rozbiórki istniejących warstw (destrukt) bitumicznych, warstw związanych...
-
Tribological performance of PTFE-metal binary coatings in rolling/sliding contact
PublicationTribological performance of surface coatings with embedded PTFE reservoirs in rolling/sliding contact is reported. Using two different coating materials and two shapes and patterns of PTFE reservoirs test samples in the form of discs were prepared and tested in a four-ball contact configuration under loads corresponding to nominal contact pressure of 0.5 and 1.0 GPa. It was found that one coating, namely aluminium-bronze with embedded...
-
Logistical Aspects of Energy Conversion Efficiency in Marine Steam Power Plants in Off-Design Conditions
PublicationThe paper presents logistical aspects of energy conversion efficiency in off-design conditions. The main part of the article is based on results of thermodynamic calculation for large propulsion steam turbine under partial loads. Calculations are made on extended mathematical model of two proposed steam turbine thermodynamic cycles using Stodola’s cone law. The conclusion based on calculation re-sults contains importance of off-design...
-
Influence of composition of raw wastewater on removal of nitrogen compounds in multistage treatment wetlands
PublicationInfluence of composition of raw wastewater on the efficiency of organic matter and nitrogen removal in multistage treatment wetlands has been examined. Commonly used indicators, like COD/BOD5 and BOD5/TN ratio, determining wastewater susceptibility to biodegradation in conventional treatment technologies were assessed. It was confirmed that multistage treatment wetland may be used for treatment of wastewater with high loads of...
-
EMC disturbances in connection of driving system
PublicationIt is known the steep voltage changes caused by IGBT frequency inverters may cause some electromagnetic problems in driving system. Special dU/dt type as well as sinusoidal filters are used in order to limit the level of the disturbances. The paper presents investigation results of EMC disturbances in inverter supplied induction motor. Experiments have proved that disturbances in current connection differ essentially. Important...
-
Experimental Research on Insufficient Water Lubrication of Marine Stern Tube Journal Bearing with Elastic Polymer Bush
PublicationWater-lubricated bearings with polymer bushes are steadily gaining popularity due to their advantages, including environmental friendliness, relatively simple construction and long-term operation. Nevertheless, in practice instances of damage to such bearings occur due to insufficient or absent flow of the lubricating agent. In this study, experimental tests established that elastic polymer bush bearing is capable of operating...
-
A PROPOSAL FOR ONE-IMAGE PHOTOGRAMMETRY SYSTEM FOR MEASURING THE CLEARANCE DISTANCE. CASE STUDY
PublicationMeasurement of the clearance distance (both in the context of the rail and road) is one of the current and increasingly discussed topics in the context of photogrammetric and image processing (computer vision) methods. The article presents a description of a simple and rapid method of measure the clearance distance between the obstacles by using one-image photogrammetry. The proposed method was tested for the railway, tram and...
-
A unified approach to the analysis of electric energy and fuel consumption of cars in city traffic
PublicationForecasting fuel and electricity consumption is an important factor determining the direction of changes in road engineering solutions, traffic management, selection of routes for public transport and development more efficient car drive systems. With a reliable and easy-to-use computational tool, it is possible to reduce the consumption of primary energy sources and reduce the emission of toxic compounds in cities. An analysis...
-
Factors affecting low-temperature cracking of asphalt pavements: analysis of field observations using the ordered logistic model
PublicationAccurate identification of factors that primarily affect the number of low-temperature cracks is crucial for selection of road materials and planning of pavement maintenance. Field investigations of lowtemperature cracks were performed in the years 2014 and 2020 on the same 68 road sections being in service in typical traffic conditions. The collected data were statistically analysed using the ordered logistic regression model....
-
Water-Lubricated Sintered Bronze Journal Bearings—Theoretical and Experimental Research
PublicationWater lubricated bearings are used from many years in shipbuilding, hydro power and other industries because of their advantages such as: extensive serviceable life, low coefficient of friction, longevity of shaft sleeve, good abrasion resistance, low maintenance required, unit simplicity, no danger of pollution and low price. Various types of water lubricated sliding bearings have been tested at the Technical University of Gdansk...
-
Experimental study on effectiveness of polymer dampers in reduction of structural vibrations
PublicationVibrations of civil engineering structures, generated by dynamic loads, may be very dangerous to the structures themselves as well as may have significant influence on human perception and comfort. A number of different methods have been proposed in order to minimize such situations. This concern newly designed structures as well as those which dynamic properties have to be modified due to problems with excessive vibrations. One...
-
Long-term performance and microbial characteristics of the anammox-enriched granular sludge cultivated in a bench-scale sequencing batch reactor
PublicationThe anammox-enriched granular sludge was successfully formed during the long-term biogranulation experiment lasting over 330 days. The cultivation was conducted at 30 ◦C in a 10-L sequencing batch reactor (SBR) fed with synthetic medium containing ammonia, nitrite and trace elements. The properties of the developed granules were investigated in terms of the biomass activity (including the growth rate of anammox bacteria), size...
-
Experimental study on the effectiveness of polymer dampers in reduction of structural vibrations
PublicationVibrations of civil engineering structures, generated by dynamic loads, may be very dangerous to the structures themselves as well as may have significant influence on human perception and comfort. A number of different methods have been proposed in order to minimize such situations. This concern newly designed structures as well as those which dynamic properties have to be modified due to problems with excessive vibrations. One...
-
Strain gauges monitoring of arch bridge over the Vistula river in Toruń during construction
PublicationIn 2013 one of the biggest Polish road bridges over the Vistula was built in Torun. Considering the use of original engineering solutions and innovative assembly it was decided on monitoring of strain gauges and assessment of building’s behaviour during its construction. The research was aimed at determining the degree of strain and the assessment of proper work of main arch girders during assembly phases. This work presents the...
-
Equivalent temperature for design of airport pavements using mechanistic-empirical methods
PublicationThe paper presents implementation of equivalent temperature for design of airport asphalt pavements. The calculation methods of equivalent temperature: the Shell method, the French method and method that use the Asphalt Institute fatique criteria were presented. An example of calculations of equivalent temperature for Gdansk Airport was introduced and discussed. It was shown that methods of calculation of equivalent temperature...
-
On the validation of the LS-DYNA Geo Metro numerical model
PublicationThe paper presents experiences gained during work with numerical model of Geo Metro vehicle used for simulations of crash tests with road safety barriers. Attention is drawn to the subject of tire/wheel breakage during collision events. Some methods for improvement of the model are presented in the paper. Several results for the normative vehicle numerical tests are introduced. Simulations were carried out using LS-DYNA finite...
-
Wzbudzone siły wewnętrzne : skutki upr0szczonego modelowania zakrzywionej estakady sprężonej
Publicationthe paper presents problems, which were encountered during the construction of a southern road bypass of city gdansk. after prestressing and removing formwork, the contractor spotted, that some of outer bearings are detached. performed analysis showed that, this situation was caused by the usage of a simplified, straight beam model during design phase. the paper shows the influence of a curved in plane prestressed system on internal...
-
Experimental test results of the 150kVA 18-pulse diode rectifier with series active power filter
PublicationThe paper presents the control system and selected results of experimental tests of the ac/dc power converter consisting of 18-pulse diode rectifier on the basis of coupled reactors and a serial active power filter. Three configurations of the 150kVA converter were tested experimentally and compared: 18-pulse diode rectifier with and without additional grid reactor and the rectifier integrated with the active power filter. The...
-
Dew Formation and Chemistry Near a Motorway in Poland
PublicationIn this study, the influence of traffic intensity on dewformation efficiency and chemistry is presented. The measurementswere conducted near the A4 motorway in SW Poland in almost flatland relief with intense agricultural activity. The dew/hoarfrost wascollected by means of insulated plain passive radiative condensersat three sites: AN and AS located in the close vicinity of themotorway (30 m) on the opposite sides of the road,...
-
Dobór geotekstyliów i wyrobów pokrewnych pełniących funkcję zbrojenia w budownictwie komunikacyjnym – wybrane problemy inżynierskie
PublicationZ uwagi na odpowiedzialność uczestników procesu budowlanego za realizowane inwestycje komunikacyjne w coraz dłuższym horyzoncie czasowym, celowe wydaje się zwrócenie uwagi na zagadnienia związane z obserwowanymi niestety nadal problemami dotyczącymi umiejętności odróżniania poszczególnych rodzajów geosyntetyków oraz weryfikacji wymaganych w projekcie tzw. technicznych parametrów istotnych (np. wytrzymałość długoterminowa w przypadku...
-
LOW NOISE TIRES FOR HYBRID AND ELECTRIC VEHICLES
PublicationLow Emission Vehicles that are hybrid and electric cars may benefit from specially designed tires that are optimized for driving conditions typical for such vehicles. It is possible that in the future Low Emission Vehicles, especially passenger cars, will substitute conventional vehicles in all applications, however for the time being they are mostly used in urban and suburban areas. Urban traffic has a rather low demand for grip...
-
Metoda zarządzania ryzykiem w inżynierii drogowej. K. Jamroz.
PublicationW monografii zaprezentowano bazujące na ryzyku podejście do zarządzania bezpieczeństwem ruchu drogowego. Można wyróżnić cztery zasadnicze jej części. W pierwszej przedstawiono przegląd problemów zarządzania bezpieczeństwem w inżynierii drogowej, pozwalający na identyfikację brakujących elementów zarządzania ryzykiem w tej dziedzinie. Następnie ukazano założenia i koncepcję metody zarządzania ryzykiem w inżynierii drogowej, nazwaną...
-
Studies on the influence of technological variants of finishing machining on flow of parts in flexible manufacturing
PublicationIn the article below the problems of influence of variants of finishing processing on flow of machining parts in flexible manufacturing system were presented. The investigations were carried out the technological processes for piston rods and rams of hydraulic cylinders. There were also presented model variants of technological processes for piston rods finished with the burnishing. In these studies the influence of technological...
-
THE COST ANALYSIS OF CORROSION PROTECTION SOLUTIONS FOR STEEL COMPONENTS IN TERMS OF THE OBJECT LIFE CYCLE COST
PublicationSteel materials, due to their numerous advantages - high availability, easiness of processing and possibility of almost any shaping are commonly applied in construction for carrying out basic carrier systems and auxiliary structures. However, the major disadvantage of this material is its high corrosion susceptibility, which depends strictly on the local conditions of the facility and the applied type of corrosion protection system....
-
Urban scene semantic segmentation using the U-Net model
PublicationVision-based semantic segmentation of complex urban street scenes is a very important function during autonomous driving (AD), which will become an important technology in industrialized countries in the near future. Today, advanced driver assistance systems (ADAS) improve traffic safety thanks to the application of solutions that enable detecting objects, recognising road signs, segmenting the road, etc. The basis for these functionalities...
-
Cycling as a Sustainable Transport Alternative in Polish Cittaslow Towns
PublicationIt is well known that growing motor traffic in urban areas causes air pollution and noise which affects the environment and public health. It is hardly surprising then that cycling should be used as an alternative mode of transport, not just in major cities but also in smaller ones including those that are members of the Cittaslow network. Their approach is based on sustainable development, care for the environment and transport...
-
Wzmocnienie przestrzennych dźwigarów kratowych z zastosowaniem dodatkowego podparcia i sprężenia
PublicationPodczas obowiązkowego przeglądu technicznego obiektu budowlanego stwierdzone zostały deformacje stalowych prętów wykratowania przestrzennych dźwigarów dachowych. Opinie techniczne dotyczące stanu technicznego potwierdziły wstępnie wykryte nieprawidłowości i nakazywały podjęcie kroków zaradczych w postaci opracowania koncepcji naprawy, a w jej ślad projektu budowlanego i wykonawczego. Do czasu naprawy obiekt został dopuszczony do...
-
Sensitivity analysis of simple random beam models by means of Monte Carlo Methods using Variance Reductions Techniques
PublicationA probabilistic sensitivity analysis of two nonlinear bar structures is presented. The analysis is carried out on the basis of the Monte Carlo method. The imperfections of the structures and the applied loads are adapted as random variables. Based on all of the generated input variables, an output response of the system is sought. Afterwards, a coefficient responsible for the structure failure is calculated and the limit state...
-
VIBRATION PROBLEMS OF AN EXAMPLE OF TEMPORARY STEEL GRANDSTAND UNDER HUMAN-INDUCED EXCITATION
PublicationLighter and slender structural members of a typical grandstand leads to a significant reduction in the frequencies, that is why such structures are more easily induced to vibrations. The aim of the present paper is to show the results of our experimental studies and the numerical analyses, focused on the behaviour of a part of a typical temporary steel grandstand under dynamic loads. The peak values of accelerations of a steel...
-
A COMPARISON OF THE WIND SPECTRUM ACCORDING TO DIFFERENT METHODS - AN ORIGINAL PROJECT OF A BUILDING ON A CLIFF IN GDYNIA
PublicationThe article presents numerical simulations of the dynamic wind loads on the structure of a building designed on a cliff in Gdynia. The results obtained from the two methods: Davenport’s and Karman’s are compared. The results allowed a comparison of the two methods, and they provided an answer to the question how a construction, designed in such an unusual condition of a cliff behaves under the influence of the gusting wind. The...
-
Benchmarking Scalability and Security Configuration Impact for A Distributed Sensors-Server IOT Use Case
PublicationInternet of Things has been getting more and more attention and found numerous practical applications. Especially important in this context are performance, security and ability to cope with failures. Especially crucial is to find good trade-off between these. In this article we present results of practical tests with multiple clients representing sensors sending notifications to an IoT middleware – DeviceHive. We investigate performance...
-
Stability of cylindrical steel silos composed of corrugated sheets and columns based on FE analyses versus Eurocode 3 approach
PublicationComprehensive static and dynamic 3D stability finite element analyses of a cylindrical steel silo composed of corrugated sheets and open thin-walled vertical stiffener profiles were carried out by taking the geometric and material non-linearity into account. The silowas subjected to axisymmetric and non-axisymmetric loads imposed by a bulk solid following Eurocode 1. Theoretical and measured initial geometric imperfections were...