Filters
total: 768
filtered: 679
Search results for: APPARENT COMPRESSION
-
Influence of rhamnolipids and ionic cross-linking conditions on the mechanical properties of alginate hydrogels as a model bacterial biofilm
PublicationThe literature indicates the existence of a relationship between rhamnolipids and bacterial biofilm, as well as the ability of selected bacteria to produce rhamnolipids and alginate. However, the influence of biosurfactant molecules on the mechanical properties of biofilms are still not fully understood. The aim of this research is to determine the effect of rhamnolipids concentration, CaCl2 concentration, and ionic cross-linking...
-
The evaluation of the vibration measurement usability of electronic indicator lemag "premet C"
PublicationThe measuring possibilities of modern compression and combustion pressure analyzers are extended with additional functions. One of them is parallel to the pressure measurement, the measurement of vibrations in the region of the cylinder head. The paper presents a general assessment of the vibration measurement function of the electronic indicator LEMAG "PREMET C". This feature is very rarely offered by manufacturers of these devices....
-
Limiting Partial Molar Volumes of Tetra-n-Alkylammonium Perchlorates in N,N-dimethylacetamide, Triethylphosphate and Dimethyl Sulfoxide at 298.15 K
PublicationThe densities of tetraalkylammonium perchlorates R4NClO4(R = methyl, or ethyl, or propyl, or butyl) and ammonium perchlorate solutions in N, N - dimethylacetamide, dimethyl sulfoxide, and triethylphosphate have been measured over the whole composition range atT = 298.15 K. From these densities, apparent and limiting partial molar volumes of the electrolytes and ions...
-
The study on application of biopolyols obtained by cellulose biomass liquefaction performed with crude glycerol for the synthesis of rigid polyurethane foams
PublicationIn this work rigid polyurethane foams (PUR) were obtained by replacement of 0–70 wt% of petrochemical polyol with bio-polyol obtained via cellulose liquefaction in presence of crude glycerol. The foams with different content of a bio-polyol were prepared by single step method for NCO/OH ratio equals 1.5. The prepared materials were analyzed in terms of their morphology, chemical structure, thermal stability and basic physical and...
-
Acoustic Heating Produced in the Thermoviscous Flow of a Shear-Thinning Fluid
PublicationThis study is devoted to the instantaneous acoustic heating of a shear-thinningfluid. Apparent viscosity of a shear-thinning fluid depends on the shear rate. Thatfeature distinguishes it from a viscous Newtonian fluid. The special linear combi-nation of conservation equations in the differential form makes it possible to derivedynamic equations governing both the sound and non-wave entropy mode inducedin the field of sound. These...
-
A Proposed Soft Computing Model for Ultimate Strength Estimation of FRP-Confined Concrete Cylinders
PublicationIn this paper, the feed-forward backpropagation neural network (FFBPNN) is used to propose a new formulation for predicting the compressive strength of fiber-reinforced polymer (FRP)-confined concrete cylinders. A set of experimental data has been considered in the analysis. The data include information about the dimensions of the concrete cylinders (diameter, length) and the total thickness of FRP layers, unconfined ultimate concrete...
-
Experimental observations on the creep behaviour of frozen soil
PublicationConstitutive models in the literature for creep of frozen soil are based on the direct use of time counted from the onset of creep. An explicit time dependence in a constitutive equation violates the principles of rational mechanics. No change in stress or temperature is allowed for during creep, using the time-based formulations. Moreover, the existing descriptions need much verification and improvement on the experimental side...
-
Towards More Realistic Probabilistic Models for Data Structures: The External Path Length in Tries under the Markov Model
PublicationTries are among the most versatile and widely used data structures on words. They are pertinent to the (internal) structure of (stored) words and several splitting procedures used in diverse contexts ranging from document taxonomy to IP addresses lookup, from data compression (i.e., Lempel- Ziv'77 scheme) to dynamic hashing, from partial-match queries to speech recognition, from leader election algorithms to distributed hashing...
-
Compact and Integrated High-Power Pulse Generation and Forming System
PublicationThis paper presents comprehensive analytical, numerical and experimental research of the compact and integrated high-power pulse generation and forming system based on the flux compression generator and the electro-explosive forming fuse. The paper includes the analysis of the presented solution, starting from the individual components studies, i.e., the separate flux compression generator tests in field conditions and the forming...
-
Feasibility of combined diesel engine - steam turbine in power station operating in the maritime
PublicationCompression-ignition engines used in ship technology as main propulsion engines are large units reaching even to 50-60 MW. Currently, the efficiency of such engines amounts to 45-50%. With such a large power unit, exhaust gases leaving the engine contain very large quantities of heat available for further treatment. Exhaust gases from the piston engine contain about 25% of the heat supplied to the engine in the fuel. Using the...
-
Akcelerator predykcji wewnątrzramkowej H.264 do kompresji obrazu w sensorach wizyjnych
PublicationW komunikacie przedstawiono konfigurowalny cyfrowy akcelerator predykcji wewnątrzramkowej przeznaczony dla enkodera wideo standardu H.264. Akcelerator realizuje predykcję typu „intra” dla makrobloków luminancji o wymiarach 4x4 i 16x16. Akcelerator wstępnie zaimplementowano w układzie FPGA, gdzie został on pomyślnie zweryfikowany, a następnie zaimplementowano go w układzie ASIC w technologii UMC 90 nm. Szczegółowe wyniki testów...
-
Akcelerator predykcji wewnątrzramkowej H.264 do kompresji obrazu w sensorach wizyjnych
PublicationW artykule przedstawiono konfigurowalny cyfrowy akcelerator predykcji wewnątrzramkowej przeznaczony dla enkodera wideo standardu H.264. Akcelerator realizuje predykcję typu „intra” dla makrobloków luminancji o wymiarach 4x4 i 16x16. Akcelerator wstępnie zaimplementowano w układzie FPGA, gdzie został on pomyślnie zweryfikowany, a następnie zaimplementowano go w układzie ASIC w technologii UMC 90 nm. Szczegółowe wyniki testów akceleratora...
-
Structural Assessment of Reinforced Concrete Beams Incorporating Waste Plastic Straws
PublicationThe behavior of reinforced concrete beams containing fibers made of waste plastic straws (WPSs) under the three point bending test is examined. The effect of WPS fiber addition on the compressive and split tensile strength is reported. Four concrete mixes were prepared. The control mix PS-0 had a proportion of 1 cement: 1 sand: 2 coarse aggregate and a water cement ratio of 0.4. In the other three mixes PS-0.5, PS-1.5 and PS-3,...
-
Numerical simulation of screw displacement pile interaction with non-cohesive soil
PublicationA trial numerical simulation of screw displacement pile interaction with non-cohesive subsoil during the transfer of compression load. The simulation was carried out in an axisymmetric system. The technological phases of pile installation in the ground were numerically modelled using equivalent processes which provided similar effects to real technical actions. The results of the numerical calculations were verified by comparing...
-
An algorithm for enhancing macromodeling in finite element analysis of waveguide components
PublicationAn algorithm for enhancing the finite element method with local model order reduction is presented. The proposed technique can be used in fast frequency domain simulation of waveguide components and resonators. The local reduction process applied to cylindrical subregions is preceded by compression of the number of variables on its boundary. As a result,the finite element large system is converted into a very compact set of linear...
-
Numerical Modelling of Shear Localization in Granular Bodies using MPM and Non-local Hypoplasticity
PublicationThe paper deals with modelling of shear localization in granular bodies by means of an enhanced hypoplastic constitutive model and material point method (MPM). The calculations were carried out for plane strain compression of non-cohesive sand. In order to properly capture the width and inclination of shear zones, the constitutive model was enriched by a characteristic length of micro-structure by means of a non-local theory....
-
Some aspects of the constitutive modelling of natural fine grained soils
PublicationThe monograph deals with selected problems of the constitutive modelling of natural fine grained soils commonly known as clays. The main idea is not to propose a unified model which is capable of describing all known features of mechanical behaviour of fine grained soils. Instead, separate models are proposed describing the mechanical behaviour of heavily overconsolidated, lightly overconsolidated and normally consolidated clays....
-
Combined cold supply system for ship application based on low GWP refrigerants - Thermo-economic and ecological analyses
PublicationThe withdrawal of popular high-GWP refrigerants will significantly affect maritime industry. Refrigeration and air conditioning systems currently used on ships are not ready to fulfil future limitations. Therefore, there is a need for system, which will operate with low-GWP refrigerants and at the same time will be efficient and reliable in difficult environmental conditions. This paper explains the concept of a cold supply system,...
-
Analyses of Shear Angle in Orthogonal Cutting of Pine Wood
PublicationThe determination of energy effects for wood machining processes, such as cutting power and cutting forces, is very useful in designing of manufacture process of wooden products. A more accurate prediction of cutting forces requires a correct determination of the shear angle value, which can be determined using various models. In this article, shear angle values for an orthogonal linear cutting process of pine wood are determined. The...
-
Fragmentomic analysis of biopeptides in silico released from milk proteins
PublicationThe fragmentomic-assisted method was employed to predict the biological potential of peptides derived from milk proteins hydrolyzed by papain and bromelain. Firstly, protein sequences were acquired from the BIOPEP-UWM database and then hydrolyzed by the above enzymes using a BIOPEP-UWM tool called “Enzyme(s) action”. The released peptides were defined as parent peptides and further analyzed for the presence of shorter peptidic...
-
Computations of critical load value of composite shell with random geometric imperfections
PublicationThe work presents the numerical analysis of composite shell with geometric imperfections subjected to compression along its generatrix. The imperfections are described as single indentations and random fields with random parameters of shape and correlation. The fields are generated with the use of the authors made program. Using the authors’ FEM software as well as commercial package Femap with NX Nastran, the critical load values...
-
LEGAL ASPECTS OF ELECTRIC ENERGY GENERATION IN A FLOATING POWER PLANT
PublicationThis paper discusses the characteristics of pollution and legal regulations governing investment projects affecting the environment. It describes a combined system of a compression ignition engine and a steam turbine, whose aim, when placed on a floating platform, is to produce electric energy in a so-called distributed generation system. Such a system involves a reciprocating internal combustion engine and a connected steam turbine...
-
Model matematyczny strat objętościowych ściskania oleju hydraulicznego w pompie wyporowej o zmiennej wydajności
PublicationCelem pracy było stworzenie możliwości oceny strat objętościowych wynikających ze ściskania oleju hydraulicznego w komorach roboczych wysokociśnieniowej pompy wyporowej o zmiennej wydajności na obrót wału. Straty objętościowe ściskania oleju muszą być określone jako funkcje tych samych parametrów, w zależności od których ocenione są straty objętościowe przecieków oleju w komorach, wynikające z jakości rozwiązania konstrukcyjnego...
-
Thermodynamic Cycles of Air Microturbine Power Plants Working on Biomass Fuels
PublicationThe gas turbine engine is modified to work as an air turbine set which consists, in the simplest arrangement, of a compressor, a heat exchanger and a turbine. Air is a working medium for both: the compressor and the turbine. This kind of air turbine set can be applied in power plants working on biomass fuels. In this solution we can burn fuels of varying parameters in the external combustion chamber without any harmful effects...
-
Load carrying capacity of the eccentric joint in the truss made of open cross-sections
PublicationThe influence of eccentricity at intersections of truss members on the load carrying capacity of the truss joint is presented in the paper. The research truss elements were designed as cold-formed open cross section. Analytical calculations, numerical analysis and experimental research were conducted to reveal how the eccentricity affects the effort of material in the joint area. The results of analysis and investigations are compared...
-
The forming and emission of high power electromagnetic pulses
PublicationAn impulse energy source, a power conditioning system and an electromagnetic field emitter are essential to generate an electromagnetic field pulse (EMFP) with a specific frequency bandwidth. Selected simulation results for a power conditioning system consisting of a fuse opening switch and a paraboloidal electromagnetic emitter have been presented in this article. The synthetic system examined in the simulation is powered by an...
-
Experimental investigation of joint with positive eccentricity in CFS truss
PublicationDue to technological restrictions, in the case of trusses made of CFS open cross-sections, positive eccentricities in the truss joints have become very frequent. Therefore studies concerning the load-bearing capacity of truss joints with positive eccentricity were undertaken. It was assumed that the resistance of cold-formed steel (CFS) open cross-section truss joints located on compression chords and with positive eccentricity...
-
Determination of Sodium Ion Diffusion Coefficient in Tin Sulfide@Carbon Anode Material Using GITT and EIS Techniques
PublicationThe electroanalytical behavior of SnSx (x = 1, 2) encapsulated into a carbon phase was studied using the galvanostatic intermittent titration technique (GITT) and electrochemical impedance spectroscopy (EIS). These techniques are widely utilized in battery systems to investigate the diffusion of alkali metal cations in anode and cathode materials depending on the concentration of ions in the host material. Here, we report different...
-
Wybrane zagadnienia przepływowe turbiny gazowej pracującej w tłoczni gazu ziemnego.
PublicationW niniejszym artykule przedstawiono cieplno-przepływowe obliczenia turbiny gazowej, stanowiącej napęd sprężarki w tłoczni gazu ziemnego. Wartości parametrów wejściowych niezbędnych do przeprowadzenia obliczeń przyjęto na podstawie danych technicznych tłoczni zasilających polski odcinek gazociągu tranzytowego Jamał-Europa, w których pracują turbiny gazowe SGT-600 firmy Siemens, o mocy 25,3 MW.
-
The forming and emission of high power electromagnetic pulses
PublicationAn impulse energy source, a power conditioning system and an electromagnetic field emitter are essential to generate an electromagnetic field pulse (EMFP) with a specific frequency bandwidth. Selected simulation results for a power conditioning system consisting of a fuse opening switch and a paraboloidal electromagnetic emitter have been presented in this article. The synthetic system examined in the simulation is powered by...
-
Wireless intelligent audio-video surveillance prototyping system
PublicationThe presented system is based on the Virtex6 FPGA and several supporting devices like a fast DDR3 memory, small HD camera, microphone with A/D converter, WiFi radio communication module, etc. The system is controlled by the Linux operating system. The Linux drivers for devices implemented in the system have been prepared. The system has been successfully verified in a H.264 compression accelerator prototype in which the most demanding...
-
Rigid polyurethane foams modified with selected flame retardants
PublicationThe flame retardants: expandable graphite, triethylphosphatehas been used in rigid polyurethane foams (PUFs). The influence of fillers amounts on processing parameters, physical-mechanical properties (compression strength, density, water absorption, brittleness)and thermal properties (thermal stability) of such foams has been analyzed.The gel, cram and rise time for PUFs modified with flame retardant has been observed during synthesis...
-
Rzadka reprezentacja sygnału niestacjonarnego w technice oszczędnego próbkowania
PublicationPrzedstawiono zastosowanie techniki oszczędnego próbkowania do rekonstrukcji sygnału niestacjonarnego na podstawie skompresowanych próbek w dziedzinie czas-częstotliwość. Zastosowano nadmiarowy algorytm z różnymi słownikami aby znaleźć rzadką reprezentację sygnału. Wyniki symulacji potwierdzają, że zastosowanie oszczędnego próbkowania pozwala na rekonstrukcję sygnału niestacjonarnego z małej liczby losowo pobranych próbek, z niewielką...
-
Characterization of magnesium doped lanthanum orthoniobate synthesized by molten salt route
PublicationMolten salt synthesis method has been used to prepare the single phase magnesium doped lanthanum orthoniobate. The phase composition has been checked by X-ray diffraction method and the microstructure studies have been performed by scanning electron microscopy. The high temperature properties of the material have been investigated by thermogravimetry and electrochemical impedance spectroscopy. A dependence between sample total...
-
Double ZIF-L structures with exceptional CO2 capacity
PublicationCarbon dioxide emission is an emerging problem nowadays and new methods are designed for its control. In this article, a report on the formation of zeolitic imidazole framework with an apparent double leaf-like morphology DZIF-L is given. The special structure of the materials prevents from aggregation of the particles providing remarkable CO2 capacity. At 0.1 MPa the CO2 uptake was 2.99 ± 0.06 mmol/g. The capacity of synthesized...
-
POMERANIAN LANDSCAPES OF MODERNIST ZASPA. CONCEPTS OF REVITALISATION OF THE HOUSING ESTATE
PublicationZaspa is a neighbourhood in Gdansk with a long locational history and numerous build-ups. It is situated in a complex landscape between the coastal strip and moraine hills. The housing estates built here in the 1970s followed the postulates of modernist urbanism, ignoring the topographical and natural specifics and the regional heritage. The result was an ergonomic but anonymous space with many current strengths...
-
Preparation, morphology and properties of natural rubber composites filled with untreated short jute fibres
PublicationGreen composites were obtained by incorporation of short jute fibres in natural rubber matrix using a laboratory two-roll mill. The influence of untreated fibre content (1, 2.5, 5, 7.5 and 10 phr) on the mechanical properties, dynamic mechanical properties, swelling properties was examined. The behaviour of prepared green composites under cyclic compression was also investigated. Fibre dispersion in rubber matrix was studied by...
-
Smaller Representation of Finite State Automata
PublicationThis paper is a follow-up to Jan Daciuk's experiments on space-effcient finite state automata representation that can be used directly for traversals in main memory. We investigate several techniques of reducing memory footprint of minimal automata, mainly exploiting the fact that transition labels and transition pointer offset values are not evenly distributed and so are suitable for compression. We achieve a gain of around 20-30%...
-
Experimental ultimate strength assessment of stiffened plates subjected to marine immersed corrosion
PublicationThis study experimentally analyses the impact of marine immersed corrosion degradation on the compressive strength of the stiffened plates where the lower degradation levels were considered. The corrosion degradation test was accelerated by controlling the natural corrosion environmental factors, avoiding applying an electric current. Different groups of corrosion degradation levels and initial plate thicknesses were investigated....
-
Microstructure and residual stresses in surface coatings with PTFE reservoirs
PublicationThe paper presents the results of experimental study into the microstructure and changes in residual stresses resulting from sliding and rolling/sliding loaded interaction between metallic surface coatings with embedded PTFE reservoirs and various counter faces. It was found that before testing surface coatings had compressive residual stresses. Molybdenum coating with all types of PTFE reservoirs displayed, as a result of testing,...
-
A study of a compact high-efficiency zero-emission power plant with oxy-fuel combustion
PublicationThis paper discusses the application of global trends in gas cycles technology using oxy-fuel combustion. This is followed by a demonstration of a design solution for a new cycle with two enhanced energy-converting devices, namely a wet combustion chamber and a spray-ejector condenser. The proposed gas and steam cycle unit is contained within a single turbine, whose benefits combine those offered by gas turbines (high inlet temperatures)...
-
Influence of the Addition of Recycled Aggregates and Polymer Fibers on the Properties of Pervious Concrete
PublicationThe aim of the study was to check the possibility of reusing aggregate from recycled concrete waste and rubber granules from car tires as partial substitution of natural aggregate. The main objective was to investigate the effects of recycled waste aggregate modified with polymer fibers on the compressive and flexural strength, modulus of elasticity and permeability of pervious concrete. Fibers with a multifilament structure and...
-
Influence of image transformations and quality degradations on SURF detector efficiency
PublicationA method for task-oriented examination of SURF keypoint detector accuracy is presented in the paper. It consists of generating test images, based on a given exemplar, processed by affine transformations: random rotation and scaling, and varying degree of degradations: darkening, blurring, noising, and compression. Details of applied degradation procedure are presented, followed by essentials of SURF-based images matching. A distance...
-
A procedure for elastoplastic hardening function identification.
PublicationThe inverse analysis method for identifying a nonlinear hardening function,which governs a plastic yielding of soil and rock materials in the framework of elastoplastic theory is presented. A concept of two stage finite element based on spatial discretization of computational space and hardening function space is introduced. The proposed inverse analysis can be classified as the output least squares method. The Levenberg Marquard...
-
Preparation and characterization of rigid polyurethane-polyglycerolnanocomposite foams
PublicationThis work reports on the preparation of polyurethane-polyisocyanurate (PUR-PIR) foams containing different polyglycerols and layered silicate nanoclays. The rigid polyurethane foams were obtained in a laboratory scale, in a single step method, from a two-component system with a NCO to OH groups ratio equal to two. The reaction mixture consisted of the proper amounts of a commercial oligoetherpolyol, polyglycerol, catalysts, water,...
-
Excess molar volume and viscosity deviation for binary mixtures of gamma-butyrolactone with dimethyl sulfoxide
PublicationThe densities of binary liquid mixtures of dimethyl sulfoxide and gamma-butyrolactone at (293.15, 298.15, 303.15 and 313.15) K and viscosity at T=298.15 K have been measured at atmospheric pressure over theentire range of concentration. From these data the excess molar volumes VE at (293.15, 298.15, 303.15 and 313.15) K and the viscosity deviation, the excess entropy, and the excess Gibbs energy of activation for viscous flow at...
-
Un nuovo fiume carsico. La deindustrializzazione in Italia nel dibattito pubblico
PublicationThe article examines the evolution of the debate on deindustrialization in Italy since its first appearance in 1980's up to the present day. Dramatic alarms alternate with long silences in a framework, both national and international, in which the most important economic organizations are struggling, apparently without success, to find a common definition of deindustrialization.
-
Możliwości ograniczenia zużycia energii napędowej urządzeń przez optymalizację doboru wymienników ciepła, właściwą konfigurację i kontrolę przepływu płynów roboczych
PublicationArtykuł poświęcony możliwości ograniczenia zużycia energii napędowej urządzeń na drodze optymalizacji doboru wymienników ciepła, właściwej konfiguracji i kontroli przepływu płynów roboczych. Przedstawiono w nim ocenę zużycia energii w systemach energetycznych o największej energochłonności w realiach Polski. Zwrócono uwagę na możliwość wykorzystania wymienników ciepła o wysokiej efektywności dla zmniejszenia oporu przenoszenia...
-
Preparation and characterization of rigid polyurethane -polyglycerol nanocomposite foams
PublicationThis work reports on the preparation of polyurethane–polyisocyanurate (PUR–PIR) foams containing different polyglycerols and layered silicate nanoclays. The rigid polyurethane foams were obtained in a laboratory scale, in a single step method, from a two-component system with a NCO to OH groups ratio equal to two. The reaction mixture consisted of the proper amounts of a commercial oligoetherpolyol, polyglycerol, catalysts, water,...
-
Thermodynamic analysis of the Compressed Air Energy Storage system coupled with the Underground Thermal Energy Storage
PublicationImprovement of flexibility is one of the key challenges for the transformation of the Polish Power System aiming at a high share of renewable energy in electricity generation. Flexible and dispatchable power plants will contribute to this ongoing transformation process as they compensate for fluctuations in electricity generation from renewable energy sources such as wind and photovoltaics. In this context, CAES storage tanks are...