displaying 1000 best results Help
Search results for: ABSORPTIVE CAPACITY
-
Probabilistic estimation of diverse soil condition impact on vertical axis tank deformation
PublicationThe calculations of fuel tanks should take into account the geometric imperfections of the structure as well as the variability of the material parameters of the foundation. The deformation of the tank shell can have a significant impact on the limit state of the structure and its operating conditions. The paper presents a probabilistic analysis of a vertical-axis, floating-roof cylindrical shell of a tank with a capacity of 50000...
-
Efektywność skrępowania betonu w grubościennych słupach typu Concrete-Filled Steel Tube o przekroju kołowym
PublicationW słupach typu CFST w stanie granicznym dochodzi do zwiększenia wytrzymałości betonu rdzenia na skutek jego skrępowania. Zaistnienie tego zjawiska zależy od wielu czynników. Jednym z najważniejszych z nich jest sztywność obwodowa płaszcza stalowego. Jej wpływ na efektywność wzrostu wytrzymałości betonu rdzenia przebadano eksperymentalnie na grupie 48 grubościennych słupów CFST. Wykazano, że nadmierne zwiększanie grubości płaszcza...
-
Enhancement of self-trapped excitons and near-infrared emission in Bi3+/Er3+ co-doped Cs2Ag0.4Na0.6InCl6 double perovskite
Open Research DataErbium (Er) complexes are used as optical gain materials for signal generation in the telecom C-band at 1540 nm, but they need a sensitizer to enhance absorption. Na+ substitution for Ag+ and Bi3+ doping at the In3+ site is a possible strategy to enhance the broadband emission of Cs2AgInCl6, which could be used as a sensitizer for energy transfer to...
-
Quasi-one-dimensional exchange interactions and short-range magnetic correlations in CuTeO4
PublicationCuTeO4 has been proposed as a crystallographically distinct, yet electronic structure analog, of the superconducting cuprates. Here, we present a detailed characterization of the physical properties of CuTeO4 to address this proposal. Fitting of magnetic susceptibility data indicates unexpected quasi-one-dimensional, antiferromagnetic correlations at high temperature, with a nearest-neighbor Heisenberg exchange of 1=164(5) K....
-
Pile Model Tests Using Strain Gauge Technology
PublicationOrdinary pile bearing capacity tests are usually carried out to determine the relationship between load and displacement of pile head. The measurement system required in such tests consists of force transducer and three or four displacement gauges. The whole system is installed at the pile head above the ground level. This approach, however, does not give us complete information about the pile-soil interaction. We can only determine...
-
Porous carbon derived from rice husks as sustainable bioresources: insights into the role of micro-/mesoporous hierarchy in hosting active species for lithium–sulphur batteries
PublicationThe exploration of natural resources as sustainable precursors affords a family of green materials. Exploring highly abundant and available biowaste precursors remaining from food processing throughout a scalable and cost-effective material synthesis path is highly important especially for new materials discovery in emerging energy storage technologies such as lithium–sulphur (Li–S) batteries. Herein, we have produced a series...
-
Machine learning-based seismic response and performance assessment of reinforced concrete buildings
PublicationComplexity and unpredictability nature of earthquakes makes them unique external loads that there is no unique formula used for the prediction of seismic responses. Hence, this research aims to implement the most well-known Machine Learning (ML) methods in Python software to propose a prediction model for seismic response and performance assessment of Reinforced Concrete Moment-Resisting Frames (RC MRFs). To prepare 92,400 data...
-
Simultaneous voltammetric determination of Cd2+, Pb2+, and Cu2+ ions captured by Fe3O4@SiO2 core-shell nanostructures of various outer amino chain length
PublicationIn the present study, we examined a novel functionalised magnetic nanoparticles Fe3O4@SiO2-Nn as a nano adsorbent for binding of Cd2+, Pb2+, Cu2+ ions in an aqueous solution. First, we obtained the nanoparticles functionalised with various carbon chains containing different number of amino groups: (3-amino)propyltriethoxysilane (Fe3O4@SiO2-N1), N-(2-aminoethyl)-3-aminopropyltrimethoxysilane (Fe3O4@SiO2-N2) and N1-(3-trimethoxysilylpropyl)diethylenetriamine...
-
ECG measurement in the bathtub - drl on one side of the bathtub, the other side of the bathtub is grounded and the system ground is grounded- men
Open Research DataThe measurement data shows the measurement of the ECG signal in water in the bathtub. The data includes the measurement time, the reference ECG signal from the chest, and the ECG signal measured by electrodes placed in the bathtub without contact with the human body. Using the presented data, it is possible to estimate the optimal arrangement of measuring...
-
Nano-structured Pt embedded in the acidic salts of heteropolymolybdate matrices: MS XAFS study
PublicationMultiple-scattering extended X-ray absorption fine structure (MS EXAFS) study combined with TEM and XRD analysis of a novel Pt-based catalyst operating at low temperature fuel cells (FCs) is presented. Innovation in the case of the considered catalyst resides in the use of a porous inorganic matrix of acidic heteropolymolybdate salts as a catalyst support. Obtained results show the relation between the matrix composition and the...
-
Currently Commercially Available Chemical Sensors Employed for Detection of Volatile Organic Compounds in Outdoor and Indoor Air
PublicationThe paper presents principle of operation and design of the most popular chemical sensors for measurement of volatile organic compounds (VOCs) in outdoor and indoor air. It describes the sensors for evaluation of explosion risk including pellistors and IR-absorption sensors as well as the sensors for detection of toxic compounds such as electrochemical (amperometric), photoionization and semiconductor with solid electrolyte ones....
-
Józef Woźniak prof. dr hab. inż.
PeopleProfessor Józef Woźniak received his M.Sc., Ph.D. and D.Sc. degrees in electronics and telecommunications from the Faculty of Electronics, Gdańsk University of Technology (GUT), Poland, in 1971, 1976 and 1991, respectively. In January 2002 he became a full professor. In 1993 he was elected Associate Dean of the Faculty of Electronics and in 1994 he was he was appointed a Professor at GUT. Simultaneously, from October 1994 till...
-
RF Input-Quasi-Reflectionless Dispersive-Delay Structures Based on Complementary-Diplexer Circuits
PublicationA class of RF dispersive-delay structures (DDSs) with input-quasi-reflectionless behavior is reported. It is based on the exploitation of complementary-diplexer circuit networks, in which the out-of-band RF-input-power echoes reflected by the main bandpass-filter-(BPF)-type channel are dissipated by the resistively-terminated auxiliary bandstop-filter-(BSF)-type channel. Specifically, it is shown that the influence of the absorptive...
-
Crystal structure and low-energy Einstein mode in ErV2Al20 intermetallic cage compound
PublicationSingle crystals of a new ternary aluminide ErV2Al20 were grown using a self-flux method. The crystal structure was determined by powder X-ray diffraction measurements and Rietveld refinement, and physical properties were studied by means of electrical resistivity, magnetic susceptibility and specific heat measurements. These measurements reveal that ErV2Al20 is a Curie-Weiss paramagnet down to 1.95 K with an effective magnetic...
-
Review and Indication of Key Activities for Energy Management Improvement in DC Microgrids
PublicationDC MicroGrids (MG) must have Energy Management Systems (EMS) to guarantee efficient, dependable, and environmentally friendly electricity. The application of Model Predictive Control (MPC), proved to be helpful due to its adaptability and capacity to use non-linear models. This paper, based on an extensive literature review, identifies and discusses the three key activities to improve the characteristics of DC microgrids, i.e.:...
-
Superconductivity of Ta-Hf and Ta-Zr alloys: Potential alloys for use in superconducting devices
PublicationThe electronic properties relevant to superconductivity are reported for bulk Ta-Hf and Ta-Zr body centered cubic alloys, in a large part to determine whether their properties are suitable for potential use in superconducting qbits. The body centered cubic unit cell sizes increase with increasing alloying. The results of magnetic susceptibility, electrical resistivity, and heat capacity characterization are reported. While elemental...
-
Simulation of parallel similarity measure computations for large data sets
PublicationThe paper presents our approach to implementation of similarity measure for big data analysis in a parallel environment. We describe the algorithm for parallelisation of the computations. We provide results from a real MPI application for computations of similarity measures as well as results achieved with our simulation software. The simulation environment allows us to model parallel systems of various sizes with various components...
-
Tin oxide nanoparticles from laser ablation encapsulated in a carbonaceous matrix – a negative electrode in lithium-ion battery applications
PublicationThis report concerns carbonaceous electrodes doped with tin(II) oxide nanoparticles. Tin nanoparticles are obtained by pulsed laser ablation in water. Crystalline nanoparticles have been encapsulated in a carbonaceous matrix formed after pyrolysis of a mixture consisting of tin/tin(IV) oxide nanoparticles and gelatine. The obtained material is characterized by means of X-ray diffraction, selected area diffraction, scanning electron...
-
Tribological model of porous bearings with particular attention given to the lubricant lubricity
PublicationThe friction and wear problems, accompanying all the tribological systems, lead to reduced service life. In order to prevent such situation, it is necessary to maintain fluid friction, which improves durability of all friction nodes in a tribological system. In the paper, the tribological system consists of porous bearings and the model deals with their weakest spots - the oil outflow points in the porous wall. A kinetic model...
-
Pylon foundation of a cable stayed bridge at the motorway ring road of Wrocław
PublicationThe largest bridge of the motorway ring road of Wroclaw is a cable stayed bridge over the Odra river near Rędzin. Due to hydrogeological conditions of the ground it was not convenient to use standard bored piles of high length. Instead shorter piles were applied with additional improvement by cement injections at the pile toes. This decision was possible by extending ground investigation program and application of numerical modeling...
-
Structural Health Monitoring of Composite Shell Footbridge for Its Design Validation
PublicationThe paper presents the structural health monitoring system of the composite bridge for pedestrians and cyclists. The footbridge was designed and manufactured within the FOBRIDGE project. It is the first bridge in the world, which is classified as a consistent single element structural girder, made of sandwich shells, entirely produced in a single cycle. The developed structural health monitoring system, supported design process,...
-
Education of Logisticians in Poland: Problems and Prospects in Students’ Opinion
PublicationLogistics is one of the key sectors of the Polish economy. Its value reflects not only its own capacity, but also the role it plays in ensuring the proper functioning of the entire economy. The rapid development of the industry and the highest demands on logistics solutions bring to the fore the problem of preparing a new generation of specialists in logistics. That is why the question of compliance to learning expectations of...
-
Analysis of Denoising Autoencoder Properties Through Misspelling Correction Task
PublicationThe paper analyzes some properties of denoising autoencoders using the problem of misspellings correction as an exemplary task. We evaluate the capacity of the network in its classical feed-forward form. We also propose a modification to the output layer of the net, which we called multi-softmax. Experiments show that the model trained with this output layer outperforms traditional network both in learning time and accuracy. We...
-
Mechanical Properties of Aluminium Bracket Strengthening
PublicationThe aim of the research is laboratory investigation of aluminium brackets employed to fasten lightweight curtain walls to building facilities. Tensile loads perpendicular to end plates (vertical) were applied here. The author focused on the solutions intended to increase the load-carrying capacity of aluminium brackets applying the plain washer form A (DIN 125; ISO 7089), plain washer with an outer diameter about 3d (DIN 9021;...
-
Low frequency nois of supecapacitor
Open Research DataDataset contains noise measurement results on prototype electrochemical double layer capacitor. The measurement procedure is described in https://dx.doi.org/10.1515/mms-2017-0059.
-
Inline Microstrip Bandpass Filter With Two Transmission Zeros and Increased Order Using Spurious Resonance of Frequency-Dependent Inverter
PublicationA design method for a class of fourth-order inline microstrip bandpass filter with two transmission zeros and 20% fractional bandwidth is presented. The filter consists of two quarter-wavelength transmission-line resonators coupled by a frequency-dependent inverter. The inverter is composed of two open-ended stubs that are connected by an interdigital capacitor and introduces two poles and two transmission zeros in the filter response....
-
Degradation of protective coatings in steel chimneys of flue gas desulfurisation system
PublicationThis paper presents problems associated with corrosion of steel stacks and changes in philosophy of corrosion protection when implemented into flue gas desulphurization systems. In-situ tests were taken by means of electrochemical impedance spectroscopy at the stack which discharges flue gas before wet lime/limestone desulphurization. A very quick electrolyte absorption by the spherical infill vinylester coating was found using...
-
Porous Phantoms Mimicking Tissues – Investigation of Optical Parameter Stability Over Time
PublicationIn terms of optical parameters, optical phantoms can now replace live tissues and be used to validate optical measurement methods. Therefore, whether these parameters would be maintained after storage for 6 months was examined. The absorption and scattering coefficients were obtained from the measured transmittance and reflectance measurements taken 6 months apart and then compared. All of the measurements were conducted using...
-
Three-point bending test of sandwich beams supporting the GFRP footbridge design process - validation
PublicationSome selected aspects concerning material and construction design issues for pedestrian footbridge made of GFRP composite materials are elaborated in this paper. The analysis is focused on validation tests, which are particularly important because of the advanced technology and materials that are used for this innovative bridge. The considered footbridge is a sandwich-type shell structure comprising of PET foam core and outer skins...
-
Flexural behaviour of concrete slabs reinforced with FRP bars in experiments and according to aci ACI 440.1R guide
PublicationThe paper presents research conducted on two concrete slabs reinforced with the carbon composite bars and two other concrete slabs reinforced with basalt composite bars. The carbon bars were plain, while the basalt ones were ribbed. The slabs were experimentally investigated in the flexural state of effort with the concentrated forces applied. The results are compared with the analytical solution proposed in the guide ACI 440.1R-06...
-
Sorption of Chlorinated Solvents on Pine and Oak sawdust
PublicationThe article presents assessment of pine and oak sawdusts as sorbents for removal of chlorinated solvents from water. Sawdusts as potential sorbents were characterized with elemental analysis and BET analyses. Sorption capacity was determined for both pine and oak sawdust towards 1,1,2-trichloroethane, tetrachloroethene and 1,1,1,2-tetrachloroethane. Pine sawdust was able to adsorb greater amounts of chlorinated solvents compared...
-
Study of QoS Parameters Measurement Methodology and Requirements in RSMAD
PublicationThe paper presents the results of analysis and research of the quality of service requirements (defined by the QoS parameters) for data transmission services in Radio System for Monitoring and Acquisition of Data from Traffic Enforcement Cameras (in short: RSMAD). The paper also presents and discusses the results of test of impact of the size of images from traffic enforcement cameras (TECs) on the average transmission time. Moreover,...
-
Simple and low-cost wireless voting system
PublicationThis paper presents the concept of a simple and low-cost wireless voting system working on the 868 MHz frequency band. Described system is dedicated to general shareholders assemblies but it can be easily adapted for other applications. The main advantage is its simplicity and mobility as it consists solely of three components - voting modules, base station and a PC application from which the whole system is managed. This architecture...
-
Corrosion Study of Ceria Protective Layer Deposited by Spray Pyrolysis on Steel Interconnects
PublicationSingle fuel cells and electrolysis cells are assembled into stacks using interconnects in order to increase power and gas production capacity. The most common choice for the interconnect material is stainless steel. It has good electrical and mechanical properties and is also cost effective. One of the problems when using steel is the formation of a thermally grown oxide scale during use which has a lower electrical conductivity...
-
Preliminary experimental research on stability of truss' joint with positive eccentricity
PublicationRecently, a very large interest in lightweight steel structures made from cold-formed sections has been noticeable. In the design practice, a large emphasis is put on rational shaping of both the thin-walled elements and constructions designed on them. The aim of this paper is to present the methodology for preparation of experimental research that model the behaviour of members in trusses made of cold-formed sections with positive...
-
Simple and low-cost wireless voting system
PublicationThis paper presents the concept of a simple and low-cost wireless voting system working in the 868 MHz frequency band. The described system is dedicated to general shareholders assemblies but it can be easily adapted for other applications. The main advantage is its simplicity and mobility as it consists solely of three components - voting modules, a base station and a PC application from which the whole system is mamaged. This...
-
Synthesis, structure and physical properties of new intermetallic spin glass-like compounds RE2PdGe3 (RE = Tb and Dy)
PublicationNew intermetallic compounds Tb2Pd1.25Ge2.75 and Dy2Pd1.25Ge2.75 have been synthesized using the arc-melting method. The crystallographic structure and magnetic, electronic transport, and thermal properties are reported. The crystal structure obtained from powder x-ray diffraction analysis suggests that these compounds crystallize in the AlB2-type structure (space group P6/mmm, no. 191) with lattice parameters a = 4.228 53(5)/4.230 54...
-
Superconductivity on a Bi Square Net in LiBi
PublicationWe present the crystallographic analysis, superconducting characterization and theoretical modeling of LiBi, that contains the lightest and the heaviest nonradioactive metal. The compound crystallizes in a tetragonal (CuAu-type) crystal structure with Bi square nets separated by Li planes (parameters a = 3.3636(1)Å and c = 4.2459(2) Å, c/a = 1.26). Superconducting state was studied in detail by magnetic susceptibility and heat...
-
Diatoms Biomass as a Joint Source of Biosilica and Carbon for Lithium-Ion Battery Anodes
PublicationThe biomass of one type cultivated diatoms (Pseudostaurosira trainorii), being a source of 3D-stuctured biosilica and organic matter—the source of carbon, was thermally processed to become an electroactive material in a potential range adequate to become an anode in lithium ion batteries. Carbonized material was characterized by means of selected solid-state physics techniques (XRD, Raman, TGA). It was shown that the pyrolysis...
-
Design of Resilient Vehicle-to-Infrastructure Systems
PublicationVehicular ad hoc networks (VANETs) have recently gained noticeable attention due to advantages in improving road traffic safety, shaping the road traffic and providing infotainment opportunities to travellers. However, transmission characteristics following from the IEEE 802.11p standard and the high mobility of VANET nodes remarkably reduce the lifetime, reach and capacity of wireless links, and often lead to simultaneous disruptions...
-
Demolition of the cereal elevator building located in the conservation protection zone in the aspect of technical, functional-utility and economic conditions
PublicationThe paper presents a description of the technical condition of the Grain Elevator building situated on the port quay, which after many years of operation has been decommissioned. The immediate reason for the cessation of operation was the change in the use profile of the port quay, which caused the handling of other goods at the quay than the bulk materials originally stored in Elewator Zbożowy. The work contains...
-
Experimental research on a hydrodynamic thrust bearing with hydrostatic lift pockets: Influence of lubrication modes on bearing performance
PublicationThe aim of the study is to investigate the performance of a thrust bearing equipped with hydrostatic lift pockets under different lubrication modes. Three types of flat land bearing lubrication modes are studied experimentally: hydrostatic lubrication (HS; forced oil injection to the pockets), hybrid lubrication (HS + HD; hydrostatic lubrication combined with the external forced bearing oil supply) and hydrodynamic lubrication...
-
Optical properties of the chemotherapy drugs used in the central nervous system lymphoma therapy: monitoring drug delivery
PublicationOur aim is to optically monitor the delivery of the chemotherapy drugs for brain tumours, particularly used in the central nervous system (CNS) lymphoma therapy. In vivo monitoring would help to optimize the treatment and avoiding unnecessary medications. Moreover, it would be beneficial to be able to measure which of the multi-regimen drugs actually do penetrate and how well into the brain tissue. There exist several potential...
-
The role of bile salts in digestion
PublicationBile salts (BS) are bio-surfactants present in the gastrointestinal tract (GIT) that play a crucial role in the digestion and absorption of nutrients. The importance of BS for controlled release and transport of lipid soluble nutrients and drugs has recently stimulated scientific interest in these physiological compounds. BS are so-called facial amphiphiles showing a molecular structure that is very distinct from classical surfactants....
-
Investigating the Impact of Curing System on Structure-Property Relationship of Natural Rubber Modified with Brewery By-Product and Ground Tire Rubber
PublicationThe application of wastes as a filler/reinforcement phase in polymers is a new strategy to modify the performance properties and reduce the price of biocomposites. The use of these fillers, coming from agricultural waste (cellulose/lignocellulose-based fillers) and waste rubbers, constitutes a method for the management of post-consumer waste. In this paper, highly-filled biocomposites based on natural rubber (NR) and ground tire...
-
Spin-Resolved Band Structure of Hoffman Clathrate [Fe(pz)2Pt(CN)4] as an Essential Tool to Predict Optical Spectra of Metal–Organic Frameworks
PublicationParamount spin-crossover properties of the 3D-Hoffman metalorganic framework (MOF) [Fe(pz)2Pt(CN)4] are generally described on the basis of the ligand field theory, which provides adequate insight into theoretical and simulation analysis of spintronic complexes. However, the ligand field approximation does not take into account the 3D periodicity of the actual complex lattice and surface effects and therefore cannot predict a full-scale...
-
Structural investigations of niobium-doped bioactive calcium-phosphate glass-ceramics by means of spectroscopic studies
PublicationSynthetic calcium-phosphate based glasses and glass-ceramics play a crucial role in the development of tissue engineering. These materials have a high biocompatibility with biological analogues, excellent ability to undergo varying degrees of resorbability and due to their non-toxicity and relatively high bioactivity they are commonly used as bone and dental implants. A substantial research effort is devoted to improve synthetic...
-
Evaluation of bacterial strains for developing effective plant growth promoting strain on chickpea growth and physico chemical properties of soil
PublicationThe study was intended to isolate and characterize the plant growth-promoting properties. A collection of microbial consortia called plant growth-promoting microorganisms (PGPM) work to increase crop growth and yield through a variety of direct mechanisms, including as nitrogen fixation, phosphate solubilization, synthesis of PGH, ammonia, and siderophore, as well as indirect mechanisms. The aim of the study was to evaluate the...
-
Possibilities of Phoslock® application to remove phosphorus compounds from wastewater treated in hybrid wetlands
PublicationTreatment wetland technologies for wastewater treatment can be easily applied for removal of all pollutants except phosphorous. They are applicable in a small towns and rural areas, places where conventional wastewater treatment plant cannot properly operate because of common economic constraints. In Poland only the 8% of rural areas are equipped with sewer system, thus treatment wetlands might be an alternative, effective and...
-
Modelling Signalised Intersections Reliability of Functioning
PublicationThe article addresses a fundamental aspect of traffic, i.e. the operation of traffic signals at intersections, in reference to the reliability theory. In many cases, when intersections carry substantial amounts of traffic, selecting control parameters to produce satisfactory traffic conditions is quite difficult. Design methods do not cover all possible situations which are the result of intersection geometry and location...