Wyszukiwarka
Wyniki wyszukiwania dla: experimental testing
-
A 95-Year-Old Concrete Arch Bridge: From Materials Characterization to Structural Analysis
PublikacjaThe structural analysis of a 95-year-old concrete arch bridge located in Jagodnik (Poland) is performed in this paper, in order to check its behavior under today’s traffic loads. The mechanical properties of both the concrete and the reinforcement are investigated by testing cores and bar stubs extracted from the bridge. Structural analysis confirms that the bridge meets today’s load requirements in terms of bearing capacity, serviceability...
-
Polynomial description of dynamic impedance spectrogram—introduction to a new impedance analysis method
PublikacjaThis paper presents a polynomial description of spectrograms obtained using Dynamic Electrochemical Impedance Spectroscopy. A method to fit the polynomial degree correctly is discussed. A simple electrical system of a diode connected in parallel with a capacitor was used for testing. Dynamic impedance measurements during potentiodynamic polarization were conducted. This paper presents an alternative analysis method that allows...
-
The Latest Advances in Wireless Communication in Aviation, Wind Turbines and Bridges
PublikacjaPresent-day technologies used in SHM (Structural Health Monitoring) systems in many implementations are based on wireless sensor networks (WSN). In the context of the continuous development of these systems, the costs of the elements that form the monitoring system are decreasing. In this situation, the challenge is to select the optimal number of sensors and the network architecture, depending on the wireless system’s other parameters...
-
On analysis of double-impact test of 1500-kg vehicle into w-beam guardrail system
PublikacjaEvery day on roads many scenarios of accidents may occur. One of the measures to minimize their consequences is road safety barriers. Finite Element analyses are being increasingly used to support the physical testing of these devices. The paper addresses the issue of a secondary impact into the previously damaged w-beam guardrail system. This situation belongs to one of the most dangerous which can happen on roads and may cause...
-
Evaluation of excessive noise effects on hearing employing psychoacoustic dosimetry
PublikacjaResearch results regarding the noise impact on hearing applying the concept of the Psychoacoustic Noise Dosimetry (PND) are presented. The general characteristics of the PND algorithm are discussed. Additionally, the results of hearing examinations conducted in the laboratory conditions are shown. The main objective of the research was to determine the time needed for the Temporary Threshold Shift to reverse. The results were used...
-
Respiratory system modelling and simulation basing on the forced oscilation technique
PublikacjaConventional methods of testing lung functioning demand a specific respiratory action of the patient. In contrast, the forced oscillation technique (fot) provides measurements obtained with a minimal cooperation of the subject. The aim of this study is to verify the usefulness of the forced oscillation technique modelling in respiratory system diagnosing. in order to do it two models of fot measurements have been considered: the...
-
The realization of ASON/GMPLS control plane
PublikacjaASON (Automatic Switched Optical Network) is a concept of optical network recommended in G.8080/Y.1304 by ITU-T. Control Plane of this network could be based on GMPLS (Generalized Multi-Protocol Label Switching) protocols like RSVP-TE, OSPF-TE, LMP. This solution is named ASON/GMPLS. In this chapter we present the control plane problems and proposes ASON/GMPLS network realization that are tested on testbed consists of three and...
-
The impact of gender wage gap on sectoral economic growth – cross-country approach
PublikacjaWe propose an empirical analysis of testing the relationship between gender wage gap and economic growth. The study takes into account 12 manufacturing sectors in 18 OECD countries for the period between 1970 and 2005.We use industrial statistics (EU KLEMS, 2008) on female and male wages that distinguish between wages paid to different groups of workers classified according to skill level: high, medium and low. We estimate augmented...
-
Potentiometric taste sensor application for liquid product taste estimation
PublikacjaThe principles of taste sense and kinds of tastes (sweet, salty, sour, bitter, umami and fat) have been described. Food quality estimation by taste sense: organoleptic testing and sensory analysis has been presented. The principle of operation of potentiometric sensor composed of several Ion Selective Electrodes or All Solid State Electrodes with polymeric membranes and macromolecular chemical compounds sensitive to substances...
-
Early warning models against bankruptcy risk for Central European and Latin American enterprises
PublikacjaThis article is devoted to the issue of forecasting the bankruptcy risk of enterprises in Latin America and Central Europe. The author has used statistical and soft computing methods to program the prediction models. It compares the effectiveness of twelve different early warningmodels for forecasting the bankruptcy risk of companies. In the research conducted, the author used data on 185 companies listed on the Warsaw Stock Exchange...
-
Comparison of state feedback and PID control of pressurizer water level in nuclear power plant
PublikacjaThe pressurizer water level control system in nuclear power plant with pressurized water reactor (PWR) is responsible for coolant mass balance. The main control goal is to stabilize the water level at a reference value and to suppress the effect of time-varying disturbances (e.g. coolant leakage in primary circuit pipeline system). In the process of PWR power plant operation incorrect water level may disturb pressure control or...
-
ADT in mammography
PublikacjaWe discuss limitations of the known methods of IR imaging in diagnostics of breast cancer. In conclusion we show that for practical reasons one requires new approaches because the known methods based on simple observation of external temperature distribution are not fully effective. Even advanced pattern recognition could not help too much for static images. We ask the question: may active dynamic thermography, known in nondestructive...
-
Monte Carlo simulations of the fracture resistance of an asphalt pavement layer
PublikacjaThe purpose of the proposed numerical model is to analyze the cracking of the wearing course in a pavement overlay, assuming a pre-existing crack that passes through the binding layer and base. The computations employed the author's simulation-based Monte Carlo material model, which describes the failure process of a Semi-Circular Bend (SCB) specimen during standard laboratory testing of asphalt concrete. A key feature of this...
-
Study on VR Application Efficiency of Selected Android OS Mobile Devices
PublikacjaCurrently, the number of scenarios for using VR (Virtual Reality) technology grows every year. Yet, there are still issues associated with it, related with the performance of the mobile device itself. The aim of this work is to perform an analysis of the effectiveness of virtual reality applications in case of mobile platforms. We put the main emphasis on examining the performance and efficiency of four different hardware and software...
-
Strength parameters of deltaic soils determined with CPTU, DMT and FVT
PublikacjaThis paper presents the results of soil investigation in soft, normally consolidated organic soil in the estuary of Vistula river. The analysis concerns clayey mud and peat layers interbedded with loose to medium-dense sands. Several Cone Penetration Tests with pore water measurement (CPTU), Dilatometer Tests (DMT) and Field Vane Tests (FVT) were performed on the testing site. The cone factor Nkt was estimated using the results...
-
Improving Traffic Light Recognition Methods using Shifting Time-Windows
PublikacjaWe propose a novel method of improving algorithms recognizing traffic lights in video sequences. Our focus is on algorithms for applications which notify the driver of a light in sight. Many existing methods process images in the recording separately. Our method bases on the observation that real-life videos depict underlying continuous processes. We named our method FSA (Frame Sequence Analyzed). It is applicable for any underlying...
-
Meconium analysis as a promising diagnostic tool for monitoring fetal exposure to toxic substances: Recent trends and perspectives
PublikacjaPrenatal exposure to toxic substances is an important public health problem. Many biological specimens obtained from the fetus or mother are used for biomonitoring. Each material reflects exposure in a specific time period and has different advantages and disadvantages in terms of accuracy, time window of detection and cost/benefit ratio. Recently, meconium has become the matrix of choice in toxicology screening for detecting exposure...
-
Artificial intelligence for software development — the present and the challenges for the future
PublikacjaSince the time when first CASE (Computer-Aided Software Engineering) methods and tools were developed, little has been done in the area of automated creation of code. CASE tools support a software engineer in creation the system structure, in defining interfaces and relationships between software modules and, after the code has been written, in performing testing tasks on different levels of detail. Writing code is still the task...
-
Inspection of Gas Pipelines Using Magnetic Flux Leakage Technology
PublikacjaMagnetic non-destructive testing methods can be classified into the earliest methods developed for assessment of steel constructions. One of them is the magnetic flux leakage technology. A measurement of the magnetic flux leakage is quite commonly used for examination of large objects such as tanks and pipelines. Construction of a magnetic flux leakage tool is relatively simple, but a quantitative analysis of recorded data is a...
-
Methods of Assessing Degradation of Supercapacitors by Using Various Measurement Techniques
PublikacjaThis article presents the qualitative analyses of the construction of supercapacitor samples. The analyses are based on the suggested thermographic measurements as well as the technique of testing the inherent noise of the investigated element. The indicated assessment methods have been referred to the currently used parameters for the qualitative evaluation of supercapacitors. The approach described in this paper, which introduces...
-
Fast-response optoelectronic detection of explosives’ residues from the nitroaromatic compounds detonation: field studies approach
PublikacjaWe are presenting an application of optoelectronic nitrogen dioxide (NO2) analyzer based on cavity enhanced absorption spectroscopy in the detection of traces of explosives after detonation. It has been shown that the analyzer using blue-violet laser is able to detect explosive residues after the detonation of various amounts of nitroaromatic compounds (75g-1kg) with higher efficiency than the HPLC soil sample testing equipment,...
-
Exploring Impact of Requirements Engineering on Other IT Project Areas – Case Study
PublikacjaRequirements Engineering (RE) is recognized as one of the most important (yet difficult) areas of software engineering that has a significant impact on other areas of IT projects and their final outcomes. Empirical studies investigating this impact are hard to conduct, mainly due to the great effort required. It is thus difficult for both researchers and industry practitioners to make evidence-based evaluations about how decisions...
-
Neural Modelling of Steam Turbine Control Stage
PublikacjaThe paper describes possibility of steam turbine control stage neural model creation. It is of great importance because wider application of green energy causes severe conditions for control of energy generation systems operation Results of chosen steam turbine of 200 MW power measurements are applied as an example showing way of neural model creation. They serve as training and testing data of such neural model. Relatively simple...
-
A method for the three-dimensional and synchronous resolution of functional and spatial matters in architectural design
PublikacjaThe article discusses the issue of applied methods of teaching architectural design at Polish universities. The authors review the common methods based on conceptual drawings solving design problems in only two dimensions. After completing the floor plans' sketching process carried out in 2D way the 3D virtual models are made - seldom cardboard mock-ups - to illustrate the final spatial form of the designed object. At the Faculty...
-
Reclaimed Rubber/Poly(ε‐caprolactone) Blends: Structure, Mechanical, and Thermal Properties
PublikacjaThe amount of elastomeric waste, especially from tires is constantly increasing on a global scale. The recycling of these residua should be considered a priority. Compounding the waste rubbers with other polymers can be an excellent alternative to reuse waste materials. This procedure requires solving the issue of the lack of compatibility between the waste rubber particles and other polymers. Simultaneously, there is a claim for...
-
Investigation of Wood Flour Size, Aspect Ratios, and Injection Molding Temperature on Mechanical Properties of Wood Flour/Polyethylene Composites
PublikacjaIn the present research, wood flour reinforced polyethylene polymer composites with a coupling agent were prepared by injection molding. The effects of wood flour size, aspect ratios, and mold injection temperature on the composites’ mechanical properties were investigated. For the preparation of the polymer composites, five different formulations were created. The mechanical properties including tensile strength and the modulus,...
-
Development and validation of a model that includes two ultrasound parameters and the plasma D-dimer level for predicting malignancy in adnexal masses: an observational study
PublikacjaBackground: Pre-operative discrimination of malignant from benign adnexal masses is crucial for planning additional imaging, preparation, surgery and postoperative care. This study aimed to define key ultrasound and clinical variables and develop a predictive model for calculating preoperative ovarian tumor malignancy risk in a gynecologic oncology referral center. We compared our model to a subjective ultrasound assessment (SUA)...
-
The Usefulness of Cyclic Diamidines with Different Core-substituents as Antitumor Agents
PublikacjaA series of related polycationic compds. has been screened for potential antitumor activity by the NCI's in vitro testing (one dose primary anticancer assay and the NCI-60 full panel screening). The GI50 values of triazines 3 and 4 are on av. 1.9 μM and 2.4 μM, resp. Furan 8 deserves mention too (1.9 μM). The biol. test results showed that carbazole 10 possessed cytotoxic activity in the nanomolar range, much better than...
-
Hydrazinolysis Products of Selected Sugar Lactones—Crystal Structure and Microbiological Activity
PublikacjaCommercially available lactones, as well as those synthesized by us, turned out to be good substrates for the synthesis of sugar hydrazides. The exception was L-ascorbic acid, whose hydrazinolysis led to the formation of a hydrazinium salt, not the hydrazide as expected. The structure of all compounds was confirmed by NMR and X-ray analyses. The lower durability of hydrazinium L-ascorbate was additionally confirmed by thermogravimetric...
-
Unsupervised Learning for Biomechanical Data Using Self-organising Maps, an Approach for Temporomandibular Joint Analysis
PublikacjaWe proposed to apply a specific machine learning technique called Self-Organising Maps (SOM) to identify similarities in the performance of muscles around human temporomandibular joint (TMJ). The performance was assessed by measuring muscle activation with the use of surface electromyography (sEMG). SOM algorithm used in the study was able to find clusters of data in sEMG test results. The SOM analysis was based on processed sEMG...
-
Development of potential candidate reference materials for drugs in bottom sediment, cod and herring tissues
PublikacjaRegular use of a reference material and participation in a proficiency testing program can improve the reliability of analytical data. This paper presents the preparation of candidate reference materials for the drugs metoprolol, propranolol, carbamazepine, naproxen, and acenocoumarol in freshwater bottom sediment and cod and herring tissues. These reference materials are not available commercially. Drugs (between 7 ng/g and 32...
-
Designate CTOD of Weld Metal of butt weld, No WOiO/II/108/2013
PublikacjaTypical (normative) testing of materials and/or welded joints do not answer on all questions about material or welded joint properties. In ship building and off-shore sectors, many strucures requires materials and joint with higher than typical fatigue resistance. Imact tests, which are carried out during welding technology qualification, gives answer about ductility, CTOD tests results about material or welded joint ability...
-
TASTE QUALITIES ESTIMATION BY TASTE SENSE AND ELECTROCHEMICAL SENSORS
PublikacjaThe principles of taste sense and kinds of tastes (sweet, salty, sour, bitter, umami and fat) have been described. Food quality estimation by taste sense: organoleptic testing and sensory analysis has been presented. The principle of operation of potentiom etric sensor composed of several Ion Selective Electrodes or All Solid State Electrodes with polymeric membranes and macromolecular chemical compounds sensitive to substances...
-
The development of an underwater telephone for digital communication purposes
PublikacjaThe underwater telephone HTL-10 has been designed to provide voice and data communication between helicopter and submarines using acoustic waves. It works in a half-duplex mode and uses analogue power-efficient modulation in the form of a single side-band, suppressed carrier, in a wide range of frequencies. It generates the transmitted signal, and processes the received signals. It is implemented with the use of digital signal...
-
Influence of low-temperature physical hardening on stiffness and tensile strength of asphalt concrete and stone mastic asphalt
PublikacjaThis paper presents laboratory testing of stiffness modulus and indirect tensile strength of three asphalt concrete (AC) and three stone mastic asphalt (SMA) mixes after isothermal storage at temperature of -20oC, at different time intervals up to 16 days. The tests under repeated dynamic loading showed physical hardening of all tested mixes which was manifested by an evident increase of their stiffness moduli after isothermal...
-
Multivariate analysis of impedance data obtained for coating systems of varying thickness applied on steel
PublikacjaElectrochemical impedance spectroscopy (EIS) has proven to be a valuable test method for the electrochemical characterization of protective coatings on metals. The common way of analysis in impedance spectroscopy is to model the impedance spectrum by means of an equivalent circuit and to extract the quantity of interest using optimization techniques. A model, corresponding to the behavior of the sample under testing, is important...
-
CTOD designation for WM and HAZ in butt joint made from S460 ML steel, Expertise No. WOiO/II/82/2015
PublikacjaTypical (normative) testing of materials and/or welded joints do not answer on all questions about material or welded joint properties. In ship building and off-shore sectors, many strucures requires materials and joint with higher than typical fatigue resistance. Imact tests, which are carried out during welding technology qualification, gives answer about ductility, CTOD tests results about material or welded joint ability to...
-
Designate CTOD Heat Affected Zone of butt weld, Report No: WOiO/II/76/2013
PublikacjaTypical (normative) testing of materials and/or welded joints do not answer on all questions about material or welded joint properties. In ship building and off-shore sectors, many strucures requires materials and joint with higher than typical fatigue resistance. Imact tests, which are carried out during welding technology qualification, gives answer about ductility, CTOD tests results about material or welded joint ability...
-
Designate of CTOD for WM and HAZ, report no: WOiO/II/122/2014
PublikacjaTypical (normative) testing of materials and/or welded joints do not answer on all questions about material or welded joint properties. In ship building and off-shore sectors, many strucures requires materials and joint with higher than typical fatigue resistance. Imact tests, which are carried out during welding technology qualification, gives answer about ductility, CTOD tests results about material or welded joint ability to...
-
The effect of tire aging on acoustic performance of CPX reference tires
PublikacjaReduction of tire/road noise is one of the biggest environmental challenges of road traffic. To reduce that noise it is necessary to perform acoustic measurements on the base of wellproven standard procedures. One method of measurements that is in common use, namely the Close Proximity Method (CPX), is described in standard ISO-DIS 11819-2. As this method is used to classify road surfaces regarding their influence on vehicle noise,...
-
Evaluating the effectiveness of Doppler frequency shift determination using pilots in broadband transmission
PublikacjaIn underwater communications, reciprocal motion between transmitter and receiver has a significant impact on reception quality. In orthogonal broadband systems that provide high bit rates, this problem becomes more important, especially in the higher frequency range, where the absolute Doppler shift is the greatest. Due to the low propagation speed of acoustic wave underwater, a substantial difference exists between the Doppler...
-
Triple correlation states between in-situ tested soil parameters
PublikacjaWhen testing soil parameters, the measured parameter values are only approximations of the true values. The measurand is determined based on metrological uncertainties or using statistical models for analysing data. Some parameters of the soil state present strong correlations, but others do not always provide simple correspondences. Multiple correlations between geotechnical parameters can provide a new perspective regarding the...
-
Sign Language Recognition Using Convolution Neural Networks
PublikacjaThe objective of this work was to provide an app that can automatically recognize hand gestures from the American Sign Language (ASL) on mobile devices. The app employs a model based on Convolutional Neural Network (CNN) for gesture classification. Various CNN architectures and optimization strategies suitable for devices with limited resources were examined. InceptionV3 and VGG-19 models exhibited negligibly higher accuracy than...
-
Virtual tour as an innovative tool for architectural education - from understanding heritage to creativity stimulation
PublikacjaThe article presents the potential of the virtual tour in architectural education as an innovative tool to better understand heritage and stimulate creativity. A methodology for creating a virtual tour based on a point cloud obtained from a survey based on 360° camera images is presented. Two different purposes for the use of point clouds are presented from reliable indicators of heritage documentation useful for digital twin modelling...
-
A prototype information system for managing and pricing e-waste
PublikacjaThere is no doubt that innovation drives development in all areas of human activity, including electrical and electronic equipment. However, the production of new equipment has a significant impact on the natural environment and a relatively high consumption of natural resources. To address these issues, the circular economy has been implemented in recent years by promoting and introducing numerous measures to facilitate the recycling...
-
Improved maximum power point tracking algorithms by using numerical analysis techniques for photovoltaic systems
PublikacjaSolar photovoltaic (PV) panels generate optimal electricity when operating at the maximum power point (MPP). This study introduces a novel MPP tracking algorithm that leverages the numerical prowess of the predictor-corrector method, tailored to accommodate voltage and current fluctuations in PV panels resulting from variable environmental factors like solar irradiation and temperature. This paper delves into the intricate dynamics...
-
Low-volume label-free SARS-CoV-2 detection with the microcavity-based optical fiber sensor
PublikacjaAccurate and fast detection of viruses is crucial for controlling outbreaks of many diseases; therefore, to date, numerous sensing systems for their detection have been studied. On top of the performance of these sensing systems, the availability of biorecognition elements specific to especially the new etiological agents is an additional fundamental challenge. Therefore, besides high sensitivity and selectivity, such advantages...
-
APPLICATION POSSIBILITIES OF THE S960 STEEL IN UNDERWATER WELDED STRUCTURES
PublikacjaIn this paper, the application possibilities of the ultra-high strength (UHSS). Domex 960 steel in the underwater welded structures are analyzed. In the research, the investigated material has been tested in bead-on-plate wet welding conditions with the usage of different heat input values, namely 0.63 kJ/mm, 0.72 kJ/mm and 0.93 kJ/mm. Specimens were performed by the manual metal arc (MMA) welding method with the usage of rutile...
-
ANALYSIS OF CLIMATIC ZONES IN POLAND WITH REGARD TO ASPHALT PERFORMANCE GRADING
PublikacjaTowards the end of the last century a new system of bitumen grading was developed and implemented as part of the American Strategic Highway Research Program (SHRP). Its aim was to better adjust the testing methods and requirements for road bitumens to the actual conditions in which those bitumens serve in road pavements. Currently in Poland, similarly as in the other EU countries, road bitumens are tested and classified with regard...
-
Two-Dimensional Gas Chromatography Coupled With Mass Spectrometry in Food Analysis
PublikacjaThe development of instrumental analytical techniques provided the opportunity for in-depth characterization of many food matrices. In particular, the use of gas chromatography coupled with mass spectrometry gives impressive results in terms of quality and authenticity testing, conducting food freshness evaluations and contamination assessments. A new variant of gas chromatography, namely two-dimensional gas chromatography (GC...