Filters
total: 916
filtered: 816
Search results for: capacity
-
Verification of punching shear outside the shear cap by the direct method
PublicationThe proposition of a method to verify the punching resistance for very large supports based on the EN 1992-1-1 standard is described in this paper. The present standard guidelines for the calculation of the punching resistance for large supports are also summarised. The proposed direct method is compared with other standard methods using an example taken from design practice. This method consists of a direct check of the shear...
-
Impact of trajectory simplification methods on modeling carbon dioxide emissions from ships
PublicationModels of ship fuel consumption and emissions play an essential role in estimating global shipping’s greenhouse gas emissions. They are also widely used for verification of reported CO2 emissions for systems like EU MRV (Monitoring, Reporting and Verification) or IMO DCS (Data Collection System). Such models achieve high accuracy using historical spatiotemporal information about each ship from AIS data. However, this approach requires substantial...
-
Characterization of corrosion in reinforced concrete beams using destructive and non-destructive tests
PublicationThe paper presents both non-destructive and destructive experimental tests on steel-reinforced concrete beams subjected to electrochemical corrosion. To examine the condition and behavior of the specimens, destructive tests were carried out, i.e., a three-point bending together with a modulated ultrasonic wave test. In addition, a series of non-destructive experiments were conducted, such as the potential measurement method, low-frequency...
-
Recycling of photovoltaic modules - legal status, technology, market prospects
PublicationThe increase in the number of manufactured and installed photovoltaic modules and the growing concern about the insufficient supply of pure silicon imply the need to take action to develop infrastructure for recycling PV modules. The article presents a multifaceted analysis of the current state of development of the photovoltaic module recycling sector from a global and national perspective. The essence of the issue was introduced...
-
Application of 3D- printed hydrogels in wound healing and regenerative medicine
PublicationHydrogels are three-dimensional polymer networks with hydrophilic properties. The modifiable properties of hydrogels and the structure resembling living tissue allow their versatile application. Therefore, increasing attention is focused on the use of hydrogels as bioinks for three-dimensional (3D) printing in tissue engineering. Bioprinting involves the fabrication of complex structures from several types of materials, cells,...
-
A Probe into the Corrosion Behavior of a WE43B Magnesium Alloy in a Simulated Body Fluid using Dynamic Electrochemical Impedance Spectroscopy
PublicationWE43B is one of the newest Mg alloys with practical application in biomedical implant technology. This work attempts to scrutinize the corrosion characteristics of WE43B alloy in a simulated body fluid (SBF) at a typical body temperature. The dynamic-electrochemical impedance spectroscopy with the capacity to track changes on surfaces in a dynamic corrosive system is used in combination with other classical techniques namely, linear...
-
The Caucasian flora: a still-to-be-discovered rich source of antioxidants
PublicationCellular redox homeostasis is a state of balance between the formation of Usually Reactive Oxygen and / or Nitrogen Species (ROS/RNS), endogenous antioxidant defence systems, and exogenous dietary antioxidants. The disturbance of redox homeostasis, by the overproduction of endogenous ROS/RNS, may increase the risk of development of so-called civilisation diseases. The solution seems to be either the increased production of endogenous...
-
RESIDENTIAL FUNCTION IN MULTI-CRITERIA MULTIFUNCTIONAL BUILDING SYSTEM DESIGN PROCESS
PublicationThe paper presents the multi-criteria approach in the design process of residential structure as a part of a multifunctional building system. The purpose of work was to broaden the field of multifunctional building system design process. Background for the presented work is to define the direction of architectural growth of the modern city center area where actually are built complex and large capacity structures with a great impact...
-
Morphology, surface properties and photocatalytic activity of the bismuth oxyhalides semiconductors prepared by ionic liquid assisted solvothermal method
PublicationThis is the first report of the effect of the ILs cation type (imidazolium, pyridinium and pyrrolidinium) on the morphology, surface properties and photoactivity of BiOX semiconductors type obtained by solvothermal method in glycerol. The various ionic liquids (IL) cation type as a halogen source and templating agent for the synthesis of the bismuth oxyhalides nanoparticles has been systematically investigated. The role of ILs...
-
Transportable, Portable and Micro Gas Chromatographs
PublicationSignificant benefits can be obtained by miniaturization of conventional benchtop gas chromatographs. The attractive features arising from miniaturization include low-power requirements, low heat capacity of separation columns, low consumption of mobile phase, enhanced performance, higher portability, and easily coupling to detectors and secondary chromatographic systems. In separation sciences, including gas phase separations,...
-
Transport of paracetamol in swellable and relaxing polyurethane nanocomposite hydrogels
PublicationPolyurethane hydrogels are potentially attractive materials for biomedical applications. They are able to absorb large amount of water, biological fluids or active substances, and thus, they have potential to be used as absorbents or wound-healing dressings. They are also used for the controlled release of therapeutics because of their capacity to embed biologically active agents in their water-swollen network. The presence of...
-
Basic sensitivity analysis of a telecommunication tower complementing standard reinforcement design process
PublicationThis paper presents straightforward sensitivity assessment of a telecommunication tower. The analysis is set toidentify the elements of the tower which may be reinforced with the greatest structural advantage. As current expertopin ions on structural redesign of similar structures due to a planned addition of extra loads are mainly based ondeterministic computations or engineering intuition,...
-
Efficient optimization approaches for microwave assisted extraction of high-quality antioxidant compounds from Salvia officinalis L.: UHPLC-HRMS differential analysis of phenolic profiles obtained by ultrasound and microwave extraction
PublicationThe study aims to optimize MAE of total phenolic compounds (TPC) and antioxidant capacity from Salvia officinalis L. leaves using a definitive screening design (DSD) and I-optimal design. UHPLC-HRMS analysis was used to identify and compare the composition of MAE and UAE optimal extracts. The results showed that DSD and I-optimal design were successfully applied for the optimization of MAE targeting phenolics and other antioxidants...
-
Model tests of cast-in-place piles formed by using different types of auger
PublicationModel tests are still a popular research tool used to observe and determine the mechanisms of pile-soil interaction. Due to the significant scale effect, the results of model tests performed in the 1g system can only be analysed from the qualitative side. This article describes and presents the results of 1g pile model tests carried out for comparative purposes. There were tested the effectiveness and efficiency of various types...
-
Badania eksperymentalne strefy przypodporowej żelbetowych belek częściowo sprężonych
PublicationThis project refers to the study the shear zone, under full and partial prestressing in comparison to beams with passive reinforcement.For comparison, variable parameters have been determined:- a/d (from 1,5 to 3,5) - it's shear span to effective depth of the beam . Assuming constant geometrical quantities, "a" is variable.- 26 beams had no vertical shear reinforcement, and the other 26 had closed stirrups.- prestressing intensity...
-
Uncertainty of antioxidant profiling in complex mixtures using liquid chromatography involving post-column derivatisation
PublicationThe main goal of this paper is to discuss the problems associated with antioxidant profiling in complex samples using a high-throughput HPLC system coupled with post-column derivatisation reactor. Based on the experimental data reported in the literature, we demonstrated that improper optimisation of temperature and/or pH assay conditions performed using an on-line derivatisation reactor may substantially change the antioxidant...
-
Application of infrared thermoography to non-contact testing of varistors
PublicationTesting of varistors using thermography was carried out in order to assess their protective properties against possible overvoltage phenomena in the form of high-level voltage surges. An advantage of the thermography technique is non-contact temperature measurement. It was proposed to assess the properties of varistors workingin electronic devices as protective elements, on the basis of estimating temperature increments on varist...
-
Methods for physical impairment constrained routing with selected protection in all-optical networks
PublicationIn this paper, we investigate the problem of survivable all-optical routing in WDM networks with physical impairments. One of the recent key issues in survivable optical network design refers to maximization of the ratio of routeable demands while keeping the overall network cost low. In WDM networks, this goal can be achieved by routing as many demands in all-optical way as possible. Based on the latest technical trends driven...
-
The reasons of considarable deflections of roof trusses in engineering analysis
PublicationThe aim of the paper is to present an unconventional analysis of deformations of roof trusses of an exhibition pavilion. Structure of the main hall of the pavilion consists of repeatable span frames with steel pillars made of I-sections, fastened in the foundations and hinged supporting roof girders. The roof trusses, completed in steel construction, have undergone considerable permanent deflections. Deformations of the lower chord...
-
COMPUTER-AIDED CONSTRUCTION AT DESIGNING REINFORCED CONCRETE COLUMNS AS PER EC
PublicationThe article presents the author’s computer program for designing and dimensioning columns in reinforced concrete structures taking into account phenomena affecting their behaviour and information referring to design as per EC. The computer program was developed with the use of C++ programming language. The program guides the user through particular dimensioning stages: from introducing basic data such as dimensions, concrete...
-
Analiza czynników wpływających na ekonomiczną efektywność elektrowni jądrowej
PublicationW artykule omówiono podstawowe czynniki, które mają wpływ na opłacalność elektrowni jądrowej. Jej efektywność ekonomiczną badano za pomocą wskaźników w postaci zaktualizowanej wartości netto inwestycji (NPV) i uśrednionego jednostkowego kosztu energii elektrycznej (LCOE). Obliczono także jednostkowy koszt wytwarzania energii elektrycznej w trakcie spłaty zobowiązań kredytowych (COE1) i po okresie spłaty (COE2). Przeprowadzono analizę...
-
Superconductivity in CaBi2
PublicationSuperconductivity is observed with critical temperature Tc = 2.0 K in self-flux-grown single crystals of CaBi2. This material adopts the ZrSi2 structure type with lattice parameters a = 4.696(1) Å, b = 17.081(2) Å and c = 4.611(1) Å. The crystals of CaBi2 were studied by means of magnetic susceptibility, specific heat and electrical resistivity measurements. The heat capacity jump at Tc is DC/gTc = 1.41, confirming bulk superconductivity;...
-
Unusual behaviour of (Np,Pu)B2C
PublicationTwo transuranium metal boron carbides, NpB2C and PuB2C have been synthesized by argon arc melting. The crystal structures of the {Np,Pu}B2C compounds were determined from single-crystal X-ray data to be isotypic with the ThB2C-type (space group R3m, a = 0.6532(2) nm; c = 1.0769(3) nm for NpB2C and a = 0.6509(2) nm; c = 1.0818(3) nm for PuB2C; Z = 9). Physical properties have been derived from polycrystalline bulk material in the...
-
COMPARISON OF NOISE EMISSION OF HCT AND CLASSIC VEHICLE COMBINATIONS FOR TIMBER TRANSPORTATION IN SWEDEN
PublicationBy means of a special simulation tool, the noise emission of a high-capacity heavy vehicle (11 axles) was compared to that of a classic heavy vehicle (a truck-dolly-semitrailer with 8 axles). The two cases are designated “Extended vehicle” versus “Classic vehicle” in this study, having total lengths of 34 and 25 m, respectively. The Classic vehicle represents the most common articulated heavy vehicle configuration for transport...
-
Ensuring sustainable development of urban public transport: A case study of the trolleybus system in Gdynia and Sopot (Poland)
PublicationElectromobility is a vital tool in reducing the environmental impact of transportation. A technologically mature means of public transport is the trolleybus. Based on a case study of the Polish cities of Gdynia and Sopot, this paper explores the factors that influence the development of the trolleybus system. Recent developments of in-motion charging (IMC) technology are analysed what provides a new analytical framework for the...
-
Shear fracture of longitudinally reinforced concrete beams under bending using Digital Image Correlation and FE simulations with concrete micro-structure based on X-ray micro-computed tomography images
PublicationThe paper presents experimental and numerical investigations of the shear fracture in rectangular concrete beams longitudinally reinforced with steel or basalt bar under quasi-static three point bending. Shear fracture process zone formation and development on the surface of beams was investigated by Digital Image Correlation (DIC) whereas thorough analyses of 3D material micro-structure, air voids, width and curvature of shear...
-
Multivariate Assessment of Procedures for Molecularly Imprinted Polymer Synthesis for Pesticides Determination in Environmental and Agricultural Samples
PublicationIn the case of quantitative and qualitative analysis of pesticides in environmental and food samples, it is required to perform a sample pre-treatment process. It allows to minimalize the impact of interferences on the final results, as well as increase the recovery rate. Nowadays, apart from routinely employed sample preparation techniques such as solid-phase extraction (SPE) or solid-phase microextraction (SPME), the application...
-
Analysis of Failure Mechanism in Joints with Positive Eccentricity in CFS Truss
PublicationThe paper presents studies concerning the load-bearing capacity of truss joints with a positive eccentricity resulting from the arrangement of geometric members and the failure mechanisms observed in the joints. Based on the previously conducted experimental study, a numerical model of the tested fragment of the CFS truss with eccentricity in the joint was created and validated. All structural details of the tested truss and the...
-
Is Digital Government Advancing Sustainable Governance? A Study of OECD/EU Countries
PublicationInternational bodies and numerous authors advocate a key role for Digital Government (DG) in improving public governance and achieving other policy outcomes. Today, a particularly relevant outcome is advancing Sustainable Governance (SG), i.e., the capacity to steer and coordinate public action towards sustainable development. This article performs an empirical study of the relationship between DG and SG using data about 41 OECD/EU...
-
Silicon oxycarbide-tin nanocomposite derived from a UV crosslinked single source preceramic precursor as high-performance anode materials for Li-ion batteries
PublicationIn this work, we report an innovative and facile UV light-assisted synthesis of a nanocomposite based on silicon oxycarbide (SiOC) and tin nanoparticles. SiOC ceramic matrix, containing a conductive free carbon phase, participates in lithium-ion storage, and buffers the volume changes of Li-alloying/de-alloying material. The reported synthesis procedure through a polymer-derived ceramic route involves the preparation of a single-source...
-
Cu-Doped Layered Double Hydroxide Constructs the Performance-Enhanced Supercapacitor Via Band Gap Reduction and Defect Triggering
PublicationLayered double hydroxides (LDHs) are regarded as the excellent electrode materials for supercapacitors because of their high theoretical capacitance and abundance. However, the poor conductivity and limited reaction kinetics of LDHs restrict their practical application severely. Herein, Cu is chosen from groups VIII/IB/IIB as dopants for Co-based LDH (CuCo-LDH). The designed metal–organic framework-derived hierarchical CuCo-LDH...
-
Antibacterial Porous Systems Based on Polylactide Loaded with Amikacin
PublicationThree porous matrices based on poly(lactic acid) are proposed herein for the controlled release of amikacin. The materials were fabricated by the method of spraying a surface liquid. Description is given as to the possibility of employing a modifier, such as a silica nanocarrier, for prolonging the release of amikacin, in addition to using chitosan to improve the properties of the materials, e.g., stability and sorption capacity....
-
Stratification of nano-pigments in anti-corrosive coatings by means of magnetic field
PublicationThe concept of self-stratification of coatings, although attractive, causes difficulties in its practical use, especially when pigments are added to the resins. An alternative way of obtaining a multilayer structure in a single step was presented. Using the inhomogeneous magnetic field and magnetically active components of the coating, the possibility of vertically graded differentiation of the one layer properties has been verified....
-
Mechanism of Li nucleation at graphite anodes and mitigation strategies
PublicationLithium metal plating is a critical safety issue in Li-ion cells with graphite anodes, and contributes significantly to ageing, drastically limiting the lifetime and inducing capacity loss. Nonetheless, the nucleation mechanism of metallic Li on graphite anodes is still poorly understood. But in-depth understanding is needed to rationally design mitigation measures. In this work, we conducted FirstPrinciples studies to elucidate...
-
Applying a Mesoscopic Transport Model to Analyse the Effects of Urban Freight Regulatory Measures on Transport Emissions—An Assessment
PublicationSustainable urban freight management is a growing challenge for local authorities due to social pressures and increasingly more stringent environmental protection requirements. Freight and its adverse impacts, which include emissions and noise, considerably influence the urban environment. This calls for a reliable assessment of what can be done to improve urban freight and meet stakeholders’ requirements. While changes in a transport...
-
Preparation and characterisation of solution-cast Nafion membrane
PublicationNafion is a commercial name for a perfluorosulfonic polymer, which has been developed in 1962 by Dupont de Nemours. This polymer consists of a polytetrafluoroethylene backbone and regular spaced long perfluorovinyl ether pendant side chains terminated by a sulfonate ionic group. These sulfonate groups are responsible for cation-exchange properties of Nafion. Thanks to the ion-exchange properties, water permeability, good chemical,...
-
Compact global association based adaptive routing framework for personnel behavior understanding
PublicationPersonnel behavior understanding under complex scenarios is a challenging task for computer vision. This paper proposes a novel Compact model, which we refer to as CGARPN that incorporates with Global Association relevance and Adaptive Routing Pose estimation Network. Our framework firstly introduces CGAN backbone to facilitate the feature representation by compressing the kernel parameter space compared with typical algorithms,...
-
Removal of cyclohexane vapors from air in biotrickling filters: Effects of gas mixture composition and circular economy approach
PublicationThis work presents results of investigations on biotrickling filtration of air polluted with cyclohexane co-treated in binary, ternary and quaternary volatile organic compounds (VOCs) mixtures, including vapors of hexane, toluene and ethanol. The removal of cyclohexane from a gas mixture depends on the physicochemical properties of the co-treated VOCs and the lower the hydrophobicity of the VOC, the higher the removal efficiency...
-
Conditions controlling atmospheric pollutant deposition via snowpack
PublicationSolid precipitation represents a potentially important addition to other measures of deposition. However, an accurate estimate of snowfall amount and pollutant loading is not a trivial matter. There are obvious distinctions between regular precipitation collection and snowpack sampling that represent the cumulative chemistry of bulk deposition. The main goal is to show the most important processes and factors that may influence...
-
Cyclic Behavior of Masonry Shear Walls Retrofitted with Engineered Cementitious Composite and Pseudoelastic Shape Memory Alloy
PublicationThe behavior of masonry shear walls reinforced with pseudoelastic Ni–Ti shape memory alloy (SMA) strips and engineered cementitious composite (ECC) sheets is the main focus of this paper. The walls were subjected to quasi-static cyclic in-plane loads and evaluated by using Abaqus. Eight cases of strengthening of masonry walls were investigated. Three masonry walls were strengthened with different thicknesses of ECC sheets using...
-
Simulation of fluid structure interaction in a novel design of high pressure axial piston pump
PublicationA novel type of an axial, piston-driven high pressure hydraulic pump with variable capacity marks a significant improvement in the area of the hydraulic machinery design. Total discharge from hydrostatic forces eliminates a need for a servomechanism, thus simplifying operation, reducing weight and introducing the possibility of the pump displacement control by computer. PWK-type pumps, invented in the Gdansk University of Technology,...
-
The investment process in the power supply industry
PublicationThe basis for power supply industry programming in a market economy should be the principle of sustainable development, which must take into account maintaining an adequate level of energy security on the one hand, and the aim to preserve the maximum degree of non-renewable resources on the other hand. Therefore, the overriding aim should be a strive to meet the current and prospective demand for energy and fuel, in conjugation...
-
Digital Public Service Innovation: Framework Proposal
PublicationThis paper proposes the Digital Public Service Innovation Framework that extends the "standard" provision of digital public services according to the emerging, enhanced, transactional and connected stages underpinning the United Nations Global e-Government Survey, with seven example "innovations" in digital public service delivery -- transparent, participatory, anticipatory, personalized, co-created, context-aware and context-smart....
-
Optimization issues in distributed computing systems design
PublicationIn recent years, we observe a growing interest focused on distributed computing systems. Both industry and academia require increasing computational power to process and analyze large amount of data, including significant areas like analysis of medical data, earthquake, or weather forecast. Since distributed computing systems – similar to computer networks – are vulnerable to failures, survivability mechanisms are indispensable...
-
CREATING A RANKING OF DIAGNOSTIC PARAMETERS FOR THE DYNAMIC PROCESS OF A MARINE COMBUSTION ENGINE IN THE ASPECT OF MULTI-CRITERIA EVALUATIONS
PublicationThe change of some of the engine’s structural parameters affects the change of toxic compound emission in exhaust gases. It mainly applies to the damage sustained by the charge exchange system as well as the fuel system and the engine supercharging system. These changes are definitely higher during dynamic states and the related transient states. As such, it is possible to speak of a diverse sensitivity of the diagnostic parameters...
-
Application of twin-plane ECT sensor for identification of the internal imperfections inside concrete beams
PublicationThe main purpose of this paper is to investigate application of special construction of Electrical Capacitance Tomography (ECT) sensor to concrete beams internal homogeneity tests. Identification of internal imperfection inside the concrete beams is one of the main problems related to analysis of the construction structure bearing capacity. Therefore, this paper shows attempts to study the measurement prospects for this non-invasive,...
-
New Polymeric Materials for Solid Phase Extraction
PublicationSolid phase extraction (SPE) is a popular sample preparation technique, which can be applied directly in gas–solid phase and liquid–solid phase, or indirectly to solid samples by using, e.g., thermodesorption with subsequent chromatographic analysis. Although SPE can be described as a physical extraction process involving a liquid phase and a solid phase, the increased use of packed sorbent formats seems to have led to a bias toward...
-
Chromatographic analyses of Lavandula angustifolia and Rosmarinus officinalis extracts and their biological effects in mammalian cells and cell-free systems
PublicationKnowledge of biological properties of natural compounds allows to understand their therapeutic value, efficacy and security. We investigated: composition of Lavandula angustifolia (LA) and Rosmarinus officinalis (RO) extracts, their antioxidant capacity, cytotoxicity and genotoxicity, their DNA-protective potential against DNA damage induced in hamster V79 cells by several genotoxins or in plasmid DNA by Fe2+ ions and activity...
-
Thermal utilization of meat-and-bone meal using the rotary kiln pyrolyzer and the fluidized bed boiler – The performance of pilot-scale installation
PublicationThermal utilization of meat-and-bone meal (MBM) is subject to stringent regulations that are meant to provide elimination of any potential pathogens. Incineration as well as other possible routes for thermal conversion of MBM are still at the research state. The universal technology was developed that allows to combust various types of waste organic materials, including animal waste, municipal solid waste and sludge, mixed at any...
-
ANALYZING TITLES OF ECONOMY NEWS TO UNDERSTAND IMPACT OF COVID-19 ON ECONOMICAL SITUATION
PublicationCovid-19 affected the whole world in a short time, causing serious panic and uncertainty in society. Because it was an unprecedented disease, the medical community has worked hard to find out how to deal with it, and it continues to do so. The rapid spread of the disease, the shortage of hospital capacity and the increase in deaths drove the whole world to a closure, so to speak. In this time period, life in the world came to a...