Filters
total: 2786
filtered: 2658
displaying 1000 best results Help
Search results for: IMPROVED YOLOV5
-
Low energy inelastic electron scattering from carbon monoxide: I. excitation of the a3Π, a’3Σ+ and AΠ1 electronic states.
PublicationDifferential scattering cross sections for electron excitation of the three lowest excited electron states of carbon monoxide are obtained experimentally using low-energy electron energy-loss spectroscopy and theoretically using the R-matrix method. The incident electron energies range from near-threshold of 6.3 eV to 20 eV. Experimental scattering angles range from 20◦ to 120◦. The normalization of the experimental cross sections...
-
Hydroxyapatite deposition on the laser modified Ti13Nb13Zr alloy
PublicationThe Ti13Nb13Zr alloy was subjected to laser modification with the Nd:YAG laser provided that such treatment would increase the surface roughness followed improved adhesion of hydroxyapatite (HAp) coatings The hydroxyapatite was deposited by electrophoretic method in suspension of 0.5 g HA powder and 100 ml ethyl alcohol. The deposition was carried out for 10 min at 10 V voltage followed by drying at room temperature for 24 h and...
-
Pulsed UV-irradiated Graphene Sensors for Ethanol Detection at Room Temperature
PublicationA graphene-based gas sensor fabricated in a FET (GFET) configuration and its sensitivity towards ethanol and methane is reported. Detection of ethanol at the level of 100 ppm was observed under pulsed UV irradiation and after cleaning by UV light in the N2 ambient. Reduction of the frequency of UV irradiation pulses resulted in increased changes in sensor resistance in the presence of ethanol. Improved sensing behavior was ascribed...
-
Voltage profiles improvement in a power network with PV energy sources – results of a voltage regulator implementation
PublicationThe constant increase in the number of photovoltaic (PV) energy sources in distribution networks is the cause of serious voltage problems. The networks built at least a dozen years ago are not provided for the installation of a large number of micro-sources. It happens that the previously properly functioning power networks are not able to provide to consumers power with the required parameters, after installing many PV sources....
-
Microemulsion Delivery Systems with Low Surfactant Concentrations: Optimization of Structure and Properties by Glycol Cosurfactants
PublicationExtensive use of microemulsions as delivery systems raises interest in the safe ingredients that can form such systems. Here, we assessed the use of two glycols, i.e., propylene glycol and pentylene glycol, and their mixtures to manipulate the properties and structure of microemulsions. Obtained systems with glycols were extensively characterized in terms of capacity to incorporate water phase, droplet size, polydispersity, structure...
-
Comparative Study of the Reinforcement Type Effect on the Thermomechanical Properties and Burning of Epoxy-Based Composites
PublicationAramid (AF), glass (GF), carbon (CF), basalt (BF), and flax (FF) fibers in the form of fabrics were used to produce the composites by hand-lay up method. The use of fabrics of similar grammage for composites’ manufacturing allowed for a comprehensive comparison of the properties of the final products. The most important task was to prepare a complex setup of mechanical and thermomechanical properties, supplemented by fire behavior...
-
Rapid Characterization of the Human Breast Milk Lipidome Using a Solid-Phase Microextraction and Liquid Chromatography-Mass Spectrometry-Based Approach.
PublicationHuman breast milk (HBM) is a biofluid consisting of various biomolecules such as proteins, lipids, carbohydrates, minerals and bioactive substances. Due to its unique and complex composition, HBM provides not only nutritional components required for the growth of the infant, but also additional protection against infections. Global insight into the composition of HBM is crucial to understanding the health benefits infants receive...
-
Fuzyjne polimerazy DNA – otrzymywanie, charakterystyka i zastosowanie
PublicationObecnie reakcje PCR (ang. Polymerase Chain Reaction) wykazują bardzo szerokie zastosowanie w diagnostyce medycznej, biologii molekularnej czy inżynierii genetycznej. Efektywność tych reakcji rozumiana jako wydajność i wierność przeprowadzonej amplifikacji jest nieodłącznie związana ze stosowaną polimerazą DNA i warunkami prowadzenia reakcji PCR. Aby sprostać wymaganiom stawianym przez nowoczesne metody diagnostyczne oraz współczesną...
-
Warstwy funkcjonalne tlenkowych ogniw paliwowych
PublicationIn this paper, results describing current research on solid oxide fuel cells conducted at Gdańsk University of Technology, Faculty of Electronics, Telecommunications and Informatics are presented. The results are related to three kinds of functional layers: a thin cathode layer between the porous cathode layer and the electrolyte to improve the cathode performance, a buffer layer between the electrolyte and the cathode to slow...
-
Improving web user experience with caching user interface
PublicationIn human-computer interaction, response time is assumed generally not to exceed significantly 1-2 seconds. While the natural competition in the Internet public Web serving ensures adhering widely to such limits, some Web environments are less competitive and offer much worse user experience in terms of response time. This paper describes a solution to significantly improve user experience in terms of response time with only modification...
-
On the independence number of some strong products of cycle-powers
PublicationIn the paper we give some theoretical and computational results on the third strong power of cycle-powers, for example, we have found the independence numbers alpha((C^2_10)^⊠3) = 30 and alpha((C^4 _14)^⊠3) = 14. A number of optimizations have been introduced to improve the running time of our exhaustive algorithm used to establish the independence number of the third strong power of cycle-powers. Moreover, our results establish...
-
A Special Section on Intelligent User Interfaces in Healthcare (IUIH)
PublicationA concept of interface has evolved from the first appearance in the form of a command line interface to the established use of direct manipulation or WIMP (windows, icons, menus and pointing) interfaces in nearly all applications. Intelligent user interfaces (IUI) form a subfield of Human-Computer Interaction research. Optimal human-computer interactions are defined as ones where users are able to perform complex tasks more quickly...
-
Radio Link Measurement Methodology for Location Service Applications
PublicationThe aim of this paper is the methodology of measurements executed in a radio link for the realization of radiolocation services in radiocommunication networks, particularly in cellular networks. The main results of the measurements obtained in the physical layer of the universal mobile telecommunications system (UMTS) are introduced. A new method for the utilization of the multipath propagation phenomenon to improve the estimation...
-
Improving Savonius rotor performance by shaping its blade edges
PublicationThe article presents the results of the numerical analysis of the flow inside the Savonius rotor. Particular at-tention has been paid to the vicinity of the blade gap in order to recognise the mechanisms controlling the flow in this area. The conclusions resulting from the analysis made the basis for an attempt to improve Savonius turbine performance via shaping rotor blade edges. The paper presents selected characteristic flow...
-
Adaptive Algorithm for Interactive Question-based Search
PublicationPopular web search engines tend to improve the relevanceof their result pages, but the search is still keyword-oriented and far from "understanding" the queries' meaning. In the article we propose an interactive question-based search algorithm that might come up helpful for identifying users' intents. We describe the algorithm implemented in a form of a questions game. The stress is put mainly on the most critical aspect of this...
-
ECONOMIC MEASURES AGAINST A PANDEMICS
PublicationThe appropriate level of treatment during periods of increasing workload in the health care system or a particular hospital is ensured either by changing the organization of the system and the principles of use of resources such as space, staff and consumables or their redistribution, or by financial resources such resources are increased or replenished. This article contributes to improve the concept of resource allocation as...
-
A new method of wind farm active power curve estimation based on statistical approach
PublicationThe purpose of this paper is to solve the wind farm active power estimation problem, introducing the method which is based on a statistical approach and robust fitting. The proposed algorithm uses a statistical approach and compared to existing ones- includes a wind direction as well as the influence of turbine start-up procedure on the estimation. The results show that additional estimation inputs i.e. the wind direction and the...
-
Comparison of Selection Schemes in Evolutionary Method of Path Planning
PublicationThis article compares an impact of using various selection schemes on the quality of the solution for the problem of planning the path for a moving object using the evolutionary method. In study case problem of avoiding collisions at sea is analyzed. The modelled environment includes static constraints (lands, canals, etc.) and dynamic objects (moving ships). Article analyses behaviour of selection schemes in two similar environments...
-
A note on total reinforcement in graphs
PublicationIn this note we prove a conjecture and inprove some results presendet in a recent paper of N. Sridharan, M.D. Elias, V.S.A. Subramanian, Total reinforcement number of a graph, AKCE Int. J. Graphs Comb. 4 (2) (2007) 197-202.
-
Prognozowanie krzywej osiadania pala wierconego z iniekcją ciśnieniową pod podstawą
PublicationArtykuł jest kontynuacją tematyki autora dotyczącą mechanizmu działania iniekcji ciśnieniowej pod podstawą pala wierconego. W poprzednich publikacjach, autor wykazał, że iniekcja ta w głównej mierze uaktywnia zwiększone opory gruntu wzdłuż pobocznicy pala. Na tej podstawie w niniejszym artykule zaprezentowano procedurę obliczeniową prognozowania krzywą osiadania pala wierconego z iniekcją ciśnieniową pod podstawą. Przedstawiono...
-
Increasing the Geometrical and Interpretation Quality of Unmanned Aerial Vehicle Photogrammetry Products Using Super-Resolution Algorithms
PublicationUnmanned aerial vehicles (UAVs) have now become very popular in photogrammetric and remote-sensing applications. Every day, these vehicles are used in new applications, new terrains, and new tasks, facing new problems. One of these problems is connected with flight altitude and the determined ground sample distance in a specific area, especially within cities and industrial and construction areas. The problem is that a safe flight...
-
Landscape as a Potential Key Concept in Urban Environmental Planning: The Case of Poland
PublicationRapid urban development increases the consumption of materials, energy, and water, resulting in an overproduction of waste and emissions. These cause many environmental threats, such as ozone layer depletion and rain acidification, leading to climate change. Therefore, the question arises on how to improve the effectiveness of tools that strengthen environmental protection. This discursive article presents an approach stressing...
-
On the Peano Theorem for Some Functional Differential Equations on Time Scale
PublicationThe Peano Theorem for some functional differential equations on time scale is proved. Assumptions are of Caratheodory type. Two counter examples for false Peano theorems in the literature are presented.
-
Influence of synthesis conditions on glass formation, structure and thermal properties in the Na 2 O-CaO-P 2 O 5 system doped with Si 3 N 4 and Mg
PublicationOxynitride phosphate glasses and glass-ceramics were prepared using new synthesis routes for phosphate glasses. Materials were melted from pre-prepared glass samples in the system Na-Ca-P-O with addition of Mg and/or Si3N4 powders under different preparation conditions. The melting process was conducted at 1000–1500 °C either under air or nitrogen atmosphere to obtain materials with different nitrogen content. Their topography...
-
Accurate Modeling of Antenna Structures by Means of Domain Confinement and Pyramidal Deep Neural Networks
PublicationThe importance of surrogate modeling techniques has been gradually increasing in the design of antenna structures over the recent years. Perhaps the most important reason is a high cost of full-wave electromagnetic (EM) analysis of antenna systems. Although imperative in ensuring evaluation reliability, it entails considerable computational expenses. These are especially pronounced when carrying out EM-driven design tasks such...
-
Comparison of properties of the new electro-mechanical model and circumferential model of the inductive-dynamic drive
PublicationThe article presents a new electromechanical model of inductive-dynamic drive. The model is implemented in two environments: Maxwell for analyzing electrodynamic phenomena including moving of the disc and Ansys which allows for stress analysis on the basis of the volume forces imported from Maxwell. Additionally, a model validation by comparing with the existing circumferential model was carried out.
-
AgileSafe – a method of introducing agile practices into safety-critical software development processes
PublicationThis article introduces AgileSafe, a new method of incorporating agile practices into critical software development while still maintaining compliance with the software assurance requirements imposed by the application domain. We present the description of the method covering the process of its application and the input and output artefacts.
-
KEMR-Net: A Knowledge-Enhanced Mask Refinement Network for Chromosome Instance Segmentation
PublicationThis article proposes a mask refinement method for chromosome instance segmentation. The proposed method exploits the knowledge representation capability of Neural Knowledge DNA (NK-DNA) to capture the semantics of the chromosome’s shape, texture, and key points, and then it uses the captured knowledge to improve the accuracy and smoothness of the masks. We validate the method’s effectiveness on our latest high-resolution chromosome...
-
Multimedia polysensory integration training system dedicated to children with educational difficulties
PublicationThis paper aims at presenting a multimedia system providing polysensory train- ing for pupils with educational difficulties. The particularly interesting aspect of the system lies in the sonic interaction with image projection in which sounds generated lead to stim- ulation of a particular part of the human brain. The system architecture, video processing methods, therapeutic exercises and guidelines for children’s interaction...
-
Gemba Kaizen: Influencing individuals behavior for better - an approach to social marketing
PublicationThe idea of providing the Gemba Kaizen philosophy to a social level can benefit not only individuals, but the society as well. The Japanese philosophy for improvement or change for better may serve companies that are looking for increasing its value by quality management. The same principles when implemented in a society may improve quality of life of its inhabitants and help solving social problems. The use of social marketing...
-
Formation of High Corrosion Resistant Nanotubular Layers on TitaniumAlloy Ti13Nb13Zr
PublicationThis paper presents results of oxidation tests and corrosion investigations of titanium alloy Ti13Nb13Zr performed at different conditions. The oxide layers have been formed by electrochemical method in 2M H3PO4 + 0.3% HF solution for 30 min. and 1 h at 20 V constantvoltage. The corrosion tests have been made by potentiodynamic method in Ringer`s solution at pH ranged between 3 and 7. It has been shown that the nano-oxide films,...
-
1D Model Callibration on the Basis on 3D calculations for Tesla Turbine
PublicationThe paper presents the system of equations for axisymmetriclaminar flow, after averaging, through the width of interdisk slit ofTesla turbine. Coefficients were introduced, as a result ofaveraging, that improve the efficiency of 1D model. The minimalnumber of such coefficients was determined. The 1D modelmakes it possible to attain analytical solutions to an accuracylimited by these coefficients. Calibration of 1D model depends...
-
Blended Learning in Teaching Safety of Electrical Installations
PublicationBlended learning becomes more commonly used in teaching information technology or other subjects, which involve practice in computer laboratories. In case of subjects with no access to computer rooms blended learning supports lecturing and teaching classes e.g. interactive lessons. The article presents the use of blended learning forms in Gdansk University of Technology in teaching the subject of Safety of Electrical Installations....
-
Chosen Analysis Results Of The Prototype Multicell Piezoelectric Motor
PublicationThis paper presents the design, modeling and tests of the prototype multicell piezoelectric motor (MPM). A new concept of the electromechanical structure of the considered prototype is based on three rotating-mode actuators. The electromechanical structure of each actuator has been considered as an independent one - referred to as a “single cell” (single actuator). Combined three resonant actuators generate three traveling waves...
-
Multiple-Input Multiple-Output Technique for Underwater Acoustic Communication System
PublicationThe performance of an underwater acoustic communication (UAC) system is limited due to tough propagation conditions in the UAC channel. Multiple-Input Multiple-Output (MIMO) technique can improve the reliability of the data transmission system, increase its speed, increase its range, and reduce the energy consumption. The paper presents an implementation method of MIMO technique in the form of coding the Space-Time Block Code and...
-
Formation of High Corrosion Resistant Nanotubular Layers on TitaniumAlloy Ti13Nb13Zr
PublicationThis paper presents results of oxidation tests and corrosion investigations of titanium alloy Ti13Nb13Zr performed at different conditions. The oxide layers have been formed by electrochemical method in 2M H3PO4 + 0.3% HF solution for 30 min. and 1 h at 20 V constantvoltage. The corrosion tests have been made by potentiodynamic method in Ringer`s solution at pH ranged between 3 and 7. It has been shown that the nano-oxide films,...
-
Techniques of acquiring additional features of the responses of individual gas sensors
PublicationGas sensors usually exhibit lack of selectivity, require fre quent calibration, exhibit drift of the response and a lot of factors, such as humidity or ambient temperature, influen ce their performance. Different approaches can be used to overcome this shortcomings. Building arrays of different sensors and usage of pattern recognition methods to analyze responses of elements...
-
Auditory-visual attention stimulator
PublicationNew approach to lateralization irregularities formation was proposed. The emphasis is put on the relationship between visual and auditory attention stimulation. In this approach hearing is stimulated using time scale modified speech and sight is stimulated by rendering the text of the currently heard speech. Moreover, displayed text is modified using several techniques i.e. zooming, highlighting etc. In the experimental part of...
-
Slurry Surfacing Mixes on the Basis of Bitumen Modified with Phenol-Cresol-Formaldehyde Resin
PublicationSlow-breaking monophase cationic bitumen emulsions have been produced on the basis of bitumen modified with phenol-cresol-formaldehyde resin (PhCR-F). Bitumen emulsions were used as a binder for thin-layer coatings with slurry surfacing mixes (SSM). Physical and technical parameters of modified and unmodified emulsions were determined and analyzed. The optimal compositions of SSM were selected according to the breaking criterion....
-
Qualitative evaluation of distributed clinical systems supporting research teams working on large-scale data
PublicationInthispaper,fivecontemporaryscalablesystemstosupportmedicalresearchteams are presented. Their functionalities extend from heterogeneous unstructured data acquisition through large-scale data storing, to on-the-fly analyzing by using robust methods. Such kinds of systems can be useful in the development of new medical procedures and recommendation rules for decision support systems. A short description of each of them is provided....
-
Effects of Xanthan Gum Biopolymer on the Permeability, Odometer, Unconfined Compressive and Triaxial Shear Behavior of a Sand
PublicationBiopolymers, which are microbially induced polymers, can be used as an alternative material to improve engineering performance of soils. In this paper, a laboratory study of 0.075-1.0 mm size sand and biopolymer (i.e., xanthan gum) mixtures with various mix ratios (0%, 0.5%, 1.0%, and 1.5%) was performed. The materials, specimen preparation, and test methods are described, as are the results of a suite of permeability, odometer, unconfined...
-
New concept and analysis of the multicell piezoelectric motor
PublicationThis work presents the design, modeling and tests of the prototype multicell piezoelectric motor (MPM). A new concept of the electromechanical structure of the considered prototype is based on three rotating-mode actuators. The electromechanical structure of each actuator has been considered as an independent one - referred to as a ”single cell” (single actuator). Combined three resonant actuators generate three traveling waves...
-
Binary-Encounter Model for Direct Ionization of Molecules by Positron-Impact
PublicationWe introduce two models for the computation of direct ionization cross sections by positron impact over a wide range of collision energies. The models are based on the binary-encounter-Bethe model and take into account an extension of the Wannier theory. The cross sections computed with these models show good agreement with experimental data. The extensions improve the agreement between theory and experiment for collision energies...
-
TECHNOLOGY OF CREATING AND USAGE OF PROECOLOGICAL BLOCK EMPTYSEED
PublicationNowadays, finding natural substitutes for mass-produced materials is one of the main tasks faced by scientists and designers. There is an increasing emphasis on the theme of ecology and the need for sustainability. Variants and methods are sought which will create environmentally friendly materials in a fast, relatively inexpensive and ecological way. The aim of this paper is to present different proposals of natural building materials...
-
Rapid EM-Driven Design of Compact RF Circuits By Means of Nested Space Mapping
PublicationA methodology for rapid design of RF circuits constituted by compact microstrip resonant-cells (CMRCs) is presented. Our approach exploits nested space mapping (NSM) technology, where the inner SM layer is used to correct the equivalent circuit model at the CMRC level, whereas the outer layer enhances the coarse model of the entire structure under design. We demonstrate that NSM dramatically improves performance of surrogate-based...
-
Fiber optic microsphere with a ZnO thin film for potential application in a refractive index sensor – theoretical study
PublicationOptical fiber sensors of refractive index play an important role in analysis of biological and chemical samples. This work presents a theoretical investigation of spectral response of a fiber optic microsphere with a zinc oxide (ZnO) thin film deposited on the surface and evaluates the prospect of using such a structure for refractive index sensing. A microsphere is fabricated by an optical fiber tapering method on the base of...
-
Open-Phase Fault Detection Method for Sensorless Five-Phase Induction Motor Drives with an Inverter Output Filter
PublicationThe paper presents the sensorless five-phase induction motor drive implementation with an inverter output filter with third harmonic injection. For the sensorless operation, the required observers are presented for the first and third harmonics with consideration of the inverter output filter. Moreover, the interaction of the observers and the control system is capable to handle a deactivation of one or two phases, which improves...
-
Polarisation effects in low-energy positron–molecule scattering
PublicationThe UK molecular R-matrix method has been adapted to treat positron collisions from polyatomic targets. A simple empirical enhancement factor which corrects for the underestimation of electron–positron polarisation and correlation effects in the calculations performed with the static-plus-polarization model at low scattering energies is presented. Application of this model to positron scattering from carbon dioxide at energies...
-
Generalized adaptive notch smoothers for real-valued signals and systems
PublicationSystems with quasi-periodically varying coefficients can be tracked using the algorithms known as generalized adaptive notch filters (GANFs). GANF algorithms can be considered an extension, to the system case, of classical adaptive notch filters (ANFs). We show that estimation accuracy of the existing algorithms, as well as their robustness to the choice of design parameters, can be considerably improved by means of compensating...
-
Bioaugmentation of a sequencing batch reactor with Archaea for the treatment of reject water
PublicationIn this study, the bioaugmentation of a sequencing batch reactor (SBR) for the treatment of reject water from wastewater treatment plant was evaluated. For the bioaugmentation step a product containing an enrichment of microorganisms from the Archaea domain was used to enhance the performance of the reactor for treating reject water. The experiment was carried out in two parallel lab-scale sequencing batch reactors. The first one...