Filters
total: 1644
filtered: 1339
-
Catalog
Chosen catalog filters
displaying 1000 best results Help
Search results for: SŁUPY CFST
-
Fast Multi-Objective Optimization of Narrow-Band Antennas Using RSA Models and Design Space Reduction
PublicationComputationally efficient technique for multi-objective design optimization of narrow-band antennas is presented. In our approach, the corrected low-fidelity antenna model (obtained through coarse-discretization EM simulations) is enhanced using frequency scaling and response correction, sampled, and utilized to obtain a fast response surface approximation (RSA) antenna surrogate. The RSA model is constructed in the reduced design space....
-
Rapid Yield Estimation and Optimization of Microwave Structures Exploiting Feature-Based Statistical Analysis
PublicationIn this paper, we propose a simple, yet reliable methodology to expediteyield estimation and optimization of microwave structures. In our approach,the analysis of the entire response of the structure at hand (e.g., $S$-parameters asa function of frequency) is replaced by response surface modeling of suitablyselected feature points. On the one hand, this is sufficient to determinewhether a design satisfies given performance specifications....
-
Verification of ESPAR Antennas Performance in the Simple and Calibration Free Localization System
PublicationThis paper presents the results of simulations and measurements of an indoor localization system that uses Electronically Steerable Parasitic Array Radiator (ESPAR) antennas with switched directional beam. Proposed antennas are dedicated for 2.4GHz ISM low-cost applications where determination of the incoming signal is required. The antennas performance is analyzed and verified with relation to positioning methods based on the...
-
Investigation of the Effect of The Temperature and Magnetization Pattern on Flux Density, Instantaneous Torque, Unbalanced Magnetic Forces of a Surface Inset PMM
PublicationElectrical machines utilized in domestic applications such as ceiling fans should have low losses and cost. Permanent magnets are used instead of rotor excitation to reduce losses. Therefore, not only the losses of the rotor winding are eliminated, but also the efficiency of the machine is increased. A surface inset consequent pole (SICP) machine has also been used to reduce costs. Because less magnets are utilized in this structure....
-
Application of deep eutectic solvents in bioanalysis
PublicationThe application of deep eutectic solvents (DESs) is sharply surging as a green alternative to conventional solvents due to their unique properties in terms of simplicity of preparation, designability and low cost. A great deal of attention has been paid to the application of these green solvents in analytical chemistry in recent years, and a lot of interesting work has been reported. This review summarizes the most relevant applications...
-
Recent and Emerging Applications of Graphene-based metamaterials in Electromagnetics
PublicationSurface Plasmon Polaritons (SPPs) operating in mid-infrared up to terahertz (THz) frequencies have been traditionally manufactured on expensive metals such as gold, silver, etc. However, such metals have poor surface confinement that limits the optical applications of SPPs. The invention of graphene is a breakthrough in plasmon-based devices in terms of design, fabrication and applications, thanks to its plasmonic wave distribution,...
-
Market Regeneration in Line with Sustainable Urban Development
PublicationThis article presents the study of the optimal design solutions for regeneration of marketplaces. It examines the design variants for the revitalisation of the marketplace, in particular, investment in their modernisation in order to find the most optimal model for transforming these public spaces to have a significant impact on the city’s development. The research is a comparative analysis of the implementation of regeneration...
-
Latest Insights on Novel Deep Eutectic Solvents (DES) for Sustainable Extraction of Phenolic Compounds from Natural Sources
PublicationPhenolic compounds have long been of great importance in the pharmaceutical, food, and cosmetic industries. Unfortunately, conventional extraction procedures have a high cost and are time consuming, and the solvents used can represent a safety risk for operators, consumers, and the environment. Deep eutectic solvents (DESs) are green alternatives for extraction processes, given their low or non-toxicity, biodegradability, and reusability....
-
Implementation of high-precision computation capabilities into the open-source dynamic simulation framework YADE
PublicationThis paper deals with the implementation of arbitrary precision calculations into the open-source discrete element framework YADE published under the GPL-2+ free software license. This new capability paves the way for the simulation framework to be used in many new fields such as quantum mechanics. The implementation details and associated gains in the accuracy of the results are discussed. Besides the "standard" double (64 bits)...
-
Three-objective antenna optimization by means of kriging surrogates and domain segmentation
PublicationIn this paper, an optimization framework for multi-objective design of antenna structures is discussed which exploits data-driven surrogates, a multi-objective evolutionary algorithm, response correction techniques for design refinement, as well as generalized domain segmentation. The last mechanism is introduced to constrain the design space region subjected to sampling, which permits reduction of the number of training data samples...
-
Rapid Design Tuning of Miniaturized Rat-Race Couplers Using Regression-Based Equivalent Network Surrogates
PublicationA simple technique for fast design tuning of compact rat-race couplers is presented. Our approach involves equivalent circuit representation, corrected by nonlinear functions of frequency with coefficients extracted through nonlinear regression. At the same time, the tuning process connects two levels of coupler representation: EM simulation of the entire circuit and re-optimization of the coupler building blocks (slow-wave cells...
-
A Review: Structural Shape and Stress Control Techniques and their Applications
PublicationThis review article presents prior studies on controlling shape and stress in flexible structures. The study offers a comprehensive survey of literature concerning the adjustment and regulation of shape, stress, or both in structures and emphasizes such control’s importance. The control of systems is classified into three primary classes: nodal movement control, axial force control, and controlling the two classes concurrently....
-
Polish Suburban Landscape made of Enterpereneurial Tissue
PublicationDwa ostatnie dekady w Polsce to okres ekspansywny rozwój małych przedsiębiorstw i równolegle dynamiczne przekształcenia przestrzeni wokół miasta . Rozwój tych dwóch zjawisk nastąpiło w okresie transformacji gospodarczej po 1989 roku . Głównym celem pracy jest zbadanie poziomu interakcji między procesem suburbanizacji i rozwojem sektora MSP w wybranych podmiejskich obszary, na przykładzie Metropolii Trójmiejskiej.
-
Inbound marketing a skuteczna komunikacja marketingowa
PublicationCelem artykułu jest ukazanie koncepcji inbound marketing jako przykładu nowego podejścia do planowania i realizacji polityki komunikacji marketingowej w Internecie. Współcześnie klienci nie chcą być atakowani nachalną reklamą lub zanudzani przez nieatrakcyjne treści. Odwracają się od marek, które prowadzą z nimi komunikację jedynie przy użyciu tradycyjnych działań komunikacji marketingowej. Znane organizacje wykorzystują do promowania...
-
Wielopoziomowy przekształtnik trakcyjny SiC z izolacją od sieci 3kV DC realizowaną za pomocą transformatorów 30kHz do napędów EZT
PublicationW referacie przedstawiono wielopoziomowy izolowany kaskadowy przekształtnik DC-AC z tranzystorami SiC MOSFET 1,2kV, przeznaczony do napędów elektrycznych zespołów trakcyjnych (EZT). Zaproponowana konstrukcja przekształtnika, przeznaczonego do pracy przy zasilaniu z sieci trakcyjnej 3kV DC, spełnia założenia energoelektronicznego transformatora trakcyjnego (z ang. Power Electronic Traction Transformer). Budowa modułowa z niskonapięciowych...
-
Hierarchiczne sterowanie predykcyjne stężeniem tlenu w reaktorze biologicznej oczyszczalni ścieków
PublicationOczyszczalnia ścieków jest złożonym systemem sterowania z powodu nieliniowej dynamiki, niepewności i braku wystarczającej liczby pomiarów, wielu skal czasu i wielowymiarowości. Napowietrzanie spełnia bardzo ważną rolę w oczyszczalni ścieków. Powietrze dostarczane do reaktorów biologicznych z jednej strony służy jako pokarm dla bakterii "pracujących" przy oczyszczaniu ścieków, z drugiej strony pomaga w procesach mieszania ścieków....
-
Optymalizacja procesów biologicznych w oczyszczalni ścieków typu SBR
PublicationObiektem zainteresowania jest biologiczna, sekwencyjna oczyszczalnia ścieków (Sequ-encing Batch Reactor – SBR). Jest to złożony system sterowania z powodu nieliniowej dyna-miki, niepewności, wielu skal czasu, wielowymiarowości i braku wystarczającej liczby pomia-rów. Warunkiem koniecznym zachodzenia większości procesów biologicznych jest dostar-czenie bakteriom oczyszczającym ścieki, odpowiedniej ilości tlenu, za pomocą instalacji...
-
Fast multi-objective optimization of antenna structures by means of data-driven surrogates and dimensionality reduction
PublicationDesign of contemporary antenna structures needs to account for several and often conflicting objectives. These are pertinent to both electrical and field properties of the antenna but also its geometry (e.g., footprint minimization). For practical reasons, especially to facilitate efficient optimization, single-objective formulations are most often employed, through either a priori preference articulation, objective aggregation,...
-
Chapter 11 – Application of Chemical Sensors and Sensor Matrixes to Air Quality Evaluation
PublicationIndoor and outdoor air quality is one of the key factors influencing human health. However, air quality evaluation is not easy task. Air is a complex system, which is subjected to changes even within short period of time. Progress in analytical methods and analytical tools provides increasingly more reliable information on the condition and quality of indoor and outdoor air. This progress, however, generates an increase in the...
-
High-Efficacy Global Optimization of Antenna Structures by Means of Simplex-Based Predictors
PublicationDesign of modern antenna systems has become highly dependent on computational tools, especially full-wave electromagnetic (EM) simulation models. EM analysis is capable of yielding accurate representation of antenna characteristics at the expense of considerable evaluation time. Consequently, execution of simulation-driven design procedures (optimization, statistical analysis, multi-criterial design) is severely hindered by the...
-
Knowledge-based performance-driven modeling of antenna structures
PublicationThe importance of surrogate modeling techniques in the design of modern antenna systems has been continuously growing over the recent years. This phenomenon is a matter of practical necessity rather than simply a fashion. On the one hand, antenna design procedures rely on full-wave electromagnetic (EM) simulation tools. On the other hand, the computational costs incurred by repetitive EM analyses involved in solving common tasks...
-
Selektywne chłodzenie mózgu noworodka po niedotlenieniu okołoporodowym. Cześć 3. Hybrydowy system selektywnego chłodzenia mózgu noworodka
PublicationZapoczątkowane brakiem tlenu procesy biochemiczne mają zgubne skutki dla układu nerwowego, w szczególności rozwijającego się. Hipotermia, czyli stan oziębienia poniżej pewnych wartości temperatur, spowalnia znacznie lub całkowicie wyhamowuje poszczególne reakcje, i to leży u podstaw jej własności neuroprotekcyjnych. Powyższe twierdzenie poparte licznymi faktami naukowymi leży u podstaw koncepcji selektywnego chłodzenia mózgu i...
-
The EU enlargement and domestic employment
PublicationThe study focuses on the interactions between EU member states' labor markets (manufacturing and tradable business services) over the period 1995-2005. We use recently released detailed sector level employment statistics, considering the effects of trade integration on the creation of links between labor force in ''Old'' and ''New'' partners in the enlarged EU. Empirical estimations show that the domestic demand for labor in the...
-
Optimization of Energetic Train Cooperation
PublicationIn the article, possible ways of using energy recovered during regenerative braking of trains are presented. It is pointed out that the return of recovered electricity directly to the catenary and its use in the energy cooperation of vehicles can be a no-cost method (without additional infrastructure). The method of energy cooperation between trains and its main assumptions, that uses the law of conservation of energy, are described...
-
Remote Monitoring of Environmental Pollutants
PublicationAtmospheric air quality is one of the key factors influencing human health. Air quality evaluation is not an easy task as the atmosphere is a complex system subjected to continuous changes in time. Observed progress in the development of measurement devices and technologies is fundamental for acquisition of more reliable information about condition and quality of atmospheric air. Unfortunately, this process leads to an increase...
-
Evaluation of the prediction ability of air pollutants based on the electronic nose responses
PublicationElectronic noses are able to perform on-line measurements of the toxic volatile compounds in air. Due to their low cost and compact size they can be placed in the areas exposed to pollution, outside the laboratory. Those advantages, on the other side, force the need for development of the reliable sensors data analysis procedures. One of the most important issues connected with electronic noses is the lack of stability of the gas...
-
Monitoring the BTEX Volatiles during 3D Printing with Acrylonitrile Butadiene Styrene (ABS) Using Electronic Nose and Proton Transfer Reaction Mass Spectrometry
PublicationWe describe a concept study in which the changes of concentration of benzene, toluene, ethylbenzene, and xylene (BTEX) compounds and styrene within a 3D printer enclosure during printing with different acrylonitrile butadiene styrene (ABS) filaments were monitored in real-time using a proton transfer reaction mass spectrometer and an electronic nose. The quantitative data on the concentration of the BTEX compounds, in particular...
-
Deflated Preconditioned Solvers for Parametrized Local Model Order Reduction
PublicationOne of steps in the design of microwave filters is numerical tuning using full-wave simulators. Typically, it is a time-consuming process as it uses advanced computational methods, e.g. the finite-element method (FEM) and it usually requires multiple optimization steps before the specification goals are met. FEM involves solving a large sparse system of equations at many frequency points and therefore its computational cost is...
-
Photogrammetry image-based approach for imperfect structure modelling and FE analysis
PublicationThis study aims to model and analyse imperfect tructures using real measurements, employing photogrammetry technique commonly used in the geodesy. The study highlights the capability of the photogrammetry in aiding the structural analysis of imperfect engineering objects. Firstly, the photogrammetry measurements of a stiffened plate are carried out using a specially designed for the purpose experimental stand. Then, the plate surface...
-
Isothermal Calorimetry and Compressive Strength Tests of Mortar Specimens for Determination of Apparent Activation Energy
PublicationThe hydration process of cementitious materials involves a thermally activated reaction that depends on the composition of the mixture and the curing temperature. The main parameter affecting the temperature variation of cast-in-place concrete is the apparent activation energy, which can be used for the efficient prediction of the temperature evolution and maturity index of hardening concrete. This paper discusses two methods to...
-
Expedited Design Closure of Antennas By Means Of Trust-Region-Based Adaptive Response Scaling
PublicationIn the letter, a reliable procedure for expedited design optimization of antenna structures by means of trust-region adaptive response scaling (TR-ARS) is proposed. The presented approach exploits two-level electromagnetic (EM) simulation models. A predicted high-fidelity model response is obtained by applying nonlinear frequency and amplitude correction to the low-fidelity model. The surrogate created this way is iteratively rebuilt...
-
Inverse surrogate models for fast geometry scaling of miniaturized dual-band couplers
PublicationRe-design of microwave structures for various sets of performance specifications is a challenging task, particularly for compact components where considerable electromagnetic (EM) cross-couplings make the relationships between geometry parameters and the structure responses complex. Here, we address geometry scaling of miniaturized dual-band couplers by means of inverse surrogate modeling. Our approach allows for fast estimation...
-
A new assay based on terminal restriction fragment length polymorphism of homocitrate synthase gene fragments for Candida species identification
PublicationCandida sp. have been responsible for an increasing number of infections, especially in patients with immunodeficiency. Species specific differentiation of the Candida sp. is difficult in routine diagnosis. This identification can have a highly significant association in therapy and prophylaxis. This work has shown a new application of terminal restriction fragment length polymorphism (t-RFLP) method in molecular identification...
-
Foamed Polyurethane Composites With Different Types of Ash – Morphological, Mechanical and Thermal Behavior Assessments
Publicationncorporation of two types of ash particles into flexible polyurethane foams has been investigated, wood ash from gasification process and fly ash resulting from coal burning in power plant. Samples were modified with 5, 10 and 15 wt% of fillers. Structure, mechanical and thermal properties of obtained foams were investigated. Incorporation of both types of ash particles resulted in materials showing...
-
DEVELOPMENT OF A COUPLED NUMERICAL AND EXPERIMENTAL APPROACH TO HYDRODYNAMIC NOISE ESTIMATION
PublicationThe hydroacoustic signature of ships' propellers can be estimated experimentally through measurements of cavitation-induced pressure fluctuations and the corresponding noise distributions at model scale. These measurements need to be performed in a cavitation tunnel under the propellers operating conditions and are quite sensitive and challenging to perform with sufficient accuracy. In comparison, the numerical approach can be...
-
Detection system for optical coherence tomography: Czerny-Turner spectrometer
PublicationResearch methods based on spectral analysis have powerful impact on development in many field of science. Signal spectrum can be a source of useful and important data. It enables to obtain information about physical and chemical properties of tested materials. This paper has been devoted to describe optical design for high resolution spectrometer, which is significant element of optical coherence tomography (OCT) systems. Designed...
-
Support Product Development Framework by Means of Set of Experience Knowledge Structure (SOEKS) and Decisional DNA
PublicationIn this paper, we propose a framework to support product development activi-ties by utilizing Set of Experience Knowledge Structure (SOEKS) and Decisional DNA (DDNA). This idea will provide a new direction to researchers working on product development, especially designers and manufacturers. They will be working on the same platform and this will be reducing their communication gap. Once the final idea is perceived about product...
-
Rapid design closure of linear microstrip antenna array apertures using response features
PublicationA simple yet reliable approach to a rapid design closure of linear antenna array apertures at the electromagnetic (EM)-simulation level is proposed. Our methodology exploits an underlying array factor (AF) model suitably corrected by means of characteristic points (angles and levels) of the radiation pattern of the EM model of the antenna array aperture. This conveniently allows for controlling both the side lobe levels...
-
A novel chemiluminescent immunoassay based on original acridinium ester labels as better solution for diagnosis of human toxoplasmosis than conventional ELISA test
PublicationToxoplasma gondii infection is one of the most common human zoonosis. Laboratory diagnosis of this disease is mainly based on the results of serological methods detecting specific antibodies in the patient’s sera. In this study we aimed to evaluate the performance of a chemiluminescence immunoassay (CLIA) based on the use of a novel immunochemical reagent in the form of the conjugate of original acridinium label (AL) attached to...
-
Dynamic soil improvement by hybrid technologies
PublicationHybrid method of subsoil improvement for road embankment foundation is described. This method is composed of two wellknown methods: dynamic replacement (DR) and microblasting (DDC) one (Deep Dynamic Compaction). The method was used for both the strengthening of the fully saturated organic subsoil as well as for acceleration of the consolidation of the organic layers. The practice ensures the expected results. A proper example on...
-
Guided waves for monitoring of plate structures with linear cracks of variable length
PublicationDamage occurring at the work of plate structures may grow to a considerable size. The joint action – the detection of a defect at the earliest possible stage, the monitoring of its growth and the determination of its critical size in the context of structural reliability allows optimizing the cost of the maintenance and repair of structural elements. Thus the development of monitoring systems for permanent observation of fault...
-
3D porous graphene-based structures- synthesis and applications
PublicationPorous carbon-based materials are of the great industrial and academic interest due to their high surface area, low density, good electrical conductivity, chemical inertness and low cost of fabrication. Up to now, the main approach to obtain porous carbon structures has involved the pyrolysis of carbonaceous natural or synthetic precursors. After the isolation of graphene, the interest in 3D porous graphene-based structures (called...
-
Optimization of Graphene Oxide Synthesis and Its Reduction
PublicationIn this article, we present the review of the chemical methods of synthesis of graphene oxide and its reduction in order to obtain the so-called reduced graphene oxide (rGO) whose properties are similar to those of pure graphene. We also present our experiments and the results in this field and the comparison of the efficiency of different methods of synthesis as well as the reduction of graphene oxide. To characterize the obtained...
-
Fast surrogate-assisted simulation-driven design of compact microwave hybrid couplers
PublicationThis work presents a robust methodology for expedited simulation-driven design optimization of compact microwave hybrid couplers. The technique relies on problem decomposition, and a bot-tom–up design strategy, starting from the level of basic building blocks of the coupler, and finishing with a tuning procedure that exploits a fast surrogate model of the entire structure. The latter is constructed by cascading local response surface...
-
Extending Service Selection Algorithms with Interoperability Analysis
PublicationApplication development by integration of existing, atomic services reduces development cost and time by extensive reuse of service components. In Service Oriented Architecture, there exist alternative versions of services supplying the same functionality but differing in Quality of Service (QoS) attributes, which enables developers to select services with optimal QoS. Existing algorithms of service selection focus on the formal...
-
Pharmaceutical and forensic drug applications of chiral supercritical fluid chromatography
PublicationTHE SUPERCRITICAL FLUID IS AN EXCELLENT CHOICE AS THE CHROMATOGRAPHIC MOBILE PHASE BECAUSE IT ALLOWS RAPID SEPARATION WITH HIGH EFFICIENCY AND APPLICATIONS INVOLVING ENANTIORESOLUTION ARE COMMON. SUPERCRITICAL FLUID CHROMATOGRAPHY (SFC) IS INCREASINGLY USED FOR ANALYTICAL, SEMI-PREPARATIVE AND PREPARATIVE PURIFICATION OF CHIRAL COMPOUNDS, INCLUDING PRODUCTION OF ENANTIOMERS THAT ARE MAINLY ENCOUNTERED DURING DRUG DEVELOPMENT. SFC...
-
Effect of Compounding Conditions on Static and Dynamic Mechanical Properties of High Density Polyethylene/Ground Tire Rubber Blends
PublicationSearching for new and cost-effective methods of waste rubber recycling is a subject of research in many scientific centers in the world. In this paper there are presented results of the research of the extrusion process of cheap and environmentally friendly thermoplastic compositions containing 50 % wt. of masses of ground tire rubber (GTR). The aim of this study was to determine the relationship between the mixing conditions and...
-
Efficient Multi-Objective Simulation-Driven Antenna Design Using Co-Kriging
PublicationA methodology for fast multi-objective antenna optimization is presented. Our approach is based on response surface approximation (RSA) modeling and variable-fidelity electromagnetic (EM) simulations. In the design process, a computationally cheap RSA surrogate model constructed from sampled coarse-discretization EM antenna simulations is optimized using a multi-objective evolutionary algorithm. The initially determined Pareto...
-
Simulation-Based Design of Microstrip Linear Antenna Arrays Using Fast Radiation Response Surrogates
PublicationFast yet accurate technique for simulation-based design of linear arrays of microstrip patch antennas is presented. Our technique includes: (i) optimization of the corrected array factor of the antenna array under design for a phase excitation taper resulting in reduced side lobes; (ii) simulation-driven optimization of the array element for element dimensions resulting in matching at and about operational frequency, and (iii)...
-
Analogue CMOS ASICs in Image Processing Systems
PublicationIn this paper a survey of analog application specific integrated circuits (ASICs) for low-level image processing, called vision chips, is presented. Due to the specific requirements, the vision chips are designed using different architectures best suited to their functions. The main types of the vision chip architectures and their properties are presented and characterized on selected examples of prototype integrated circuits (ICs)...