Filters
total: 2181
filtered: 1778
displaying 1000 best results Help
Search results for: publishing behaviour
-
Non-linear FEM analysis of pounding-involved response of buildings under non-uniform earthquake excitation
PublicationThe aim of the paper is to show the results of the study investigating the influence of non-uniform earthquake excitation, due to spatial seismic effects connected with the propagation of seismic wave, on the pounding-involved response of two buildings. The three-dimensional non-linear FEM analysis has been conducted using the detailed models of colliding structures. Acceleration records for different structural supports have been...
-
Enhancing the Seismic Resistance of Columns by GFRP Confinement Using Flexible Adhesive-Experimental Study
PublicationIn this paper, the results of two experiments, focused on testing the effectiveness of a method of enhancing the seismic (dynamic) resistance of masonry columns with the use of flexible polymer adhesive, are shown. The first experiment was devoted to investigate the damping properties of a polymer working between two stiff layers, whereas the aim of the second one was to verify if the identified damping properties of the polymer...
-
Earthquake-induced pounding between superstructure segments of isolated bridge
PublicationThe use of seismic isolation in bridges is considered as one of the most promising advanced technologies to enhance the structural safety during earthquakes. However, the method results in larger displacements of superstructure segments increasing the probability of pounding between them. Reports after severe ground motions show that the earthquake-induced structural pounding may lead to significant damage in isolated bridges....
-
Entrepreneurial potential: what do we know about it?
PublicationW rozdziale zwrócono uwagę na niejednoznaczności w definiowaniu przedsiębiorczości i pojęcia przedsiębiorcy, poświęcając też sporo miejsca problemowi stawania się przedsiębiorcą i próbując odpowiedzieć na pytanie czy przedsiębiorcą można się urodzić, czy też można nauczyć się być przedsiębiorcą. Przy pomocy prostego modelu opisano też rolę, jaką edukacja w zakresie przedsiębiorczości pełni w rozwoju tej ostatniej. W dalszej części...
-
Nonlinear and linear impedance of bismuth vanadate ceramics and its relation to structural properties
PublicationThe nonlinear and linear electrical properties, topography, and microstructure of bismuth-vanadate ceramics, were studied. The structurewas observed with the use of X-ray diffraction (XRD), scanning electronmicroscopy (SEM), atomic force microscopy (AFM) and confocal microscopy methods. The obtained results showed that ceramic is porous. Two phase transitionswere determinedwith the use of DSC measurements. The linear and nonlinear ac...
-
Experimental dynamic study on a timber-frame house using shaking table
PublicationThe aim of this paper is to show the results of the shaking table experimental study concerning the behaviour of the model of the timber-frame house under earthquake excitation and impact loading. In order to determine the basic dynamic properties of the undamaged structure, the free vibration and the sweep-sine tests were first conducted. Then, the model was excited using the time history record of the El Centro earthquake of...
-
Evolutionary Sets Of Safe Ship Trajectories: A New Approach To Collision Avoidance
PublicationThe paper introduces a new method of solving multi-ship encounter situations for both open waters and restricted water regions. The method, called evolutionary sets of safe trajectories combines some of the assumptions of game theory with evolutionary programming and aims to find optimal set of safe trajectories of all ships involved in an encounter situation. In a two-ship encounter situation it enables the operator of an on-board...
-
Fluid–solid interaction on a thin platelet with high-velocity flow: vibration modelling and experiment
PublicationThe paper concerns the nonlinear behaviour of a thin platelet that is streamlined in an aerodynamic tunnel. The air velocity in the aerodynamic tunnel was at 858.9 km/h or 0.7 Ma (Ma—Mach number is a dimensionless quantity in fluid dynamics representing the ratio of flow velocity past a boundary to the local speed of sound). This experiment was numerically simulated using FSI (fluid–solid interaction) tools, namely the coupling...
-
Influence of Toll Collection Method on Motorways on Traffic Safety and Efficiency
PublicationThe paper presents the results of the effectiveness analysis for various forms of toll collection on motorway gates and their impact on safety and efficiency of traffic. The results from field tests that were performed on the A1 motorway in Rusocin were used for the analysis. The research included the analysis of the video image of driver behaviour on the way to the toll booths and at toll booths. The PTV VISSIM tool was used to...
-
Low-frequency tripping characteristics of residual current devices
PublicationFast development of various types of converters makes their utilization in industry and in domestic installations very common. Due to converters, an earth fault current waveform in modern circuits can be distorted or its frequency can be different than 50/60 Hz. Frequency of earth fault (residual) current influences tripping of residual current devices which are widely used in low voltage systems. This paper presents the behaviour...
-
Global sensitivity analysis of membrane model of abdominal wall with surgical mesh
PublicationThe paper addresses the issue of ventral hernia repair. Finite Element simulations can be helpful in the optimization of hernia parameters. A membrane abdominal wall model is proposed in two variants: a healthy one and including hernia defect repaired by implant. The models include many uncertainties, e.g. due to variability of abdominal wall, intraabdominal pressure value etc. Measuring mechanical properties with high accuracy...
-
Dynamic analysis of temporary steel grandstand equipped with different types of bracing system
PublicationIn the paper, behaviour of a temporary steel grandstand equipped with two different types of bracing system has been analysed through the numerical study. A typical solution concerning application of a diagonal tubular members has been compared with elements proposed by authors and called polymer dampers. A polymer element consists of two L-shape steel members bonded with polymer mass. The aim of the paper is to verify the effectiveness...
-
Rigid finite elements and multibody modeling in analyses of a robot shaped elastic/plastic deformations of a beam
PublicationDynamics analysis of a system composed of a parallel manipulator and of an elastic beam is presented in the paper. Classic 3RRR parallel manipulator is considered and used to deform the beam. Elasto-plastic deformations are investigated. Rigid-finite-elements technique is employed to deal with dynamics of the beam. A multibody structure is associated with the introduced hybrid system in order to model its dynamics. Idea of the...
-
Adaptation of the arbitrary Lagrange–Euler approach to fluid–solid interaction on an example of high velocity flow over thin platelet
PublicationThe aim of this study is to analyse the behaviour of a thin plate with air flow velocities of 0.3–0.9 Ma. Data from the experiment and numerical tools were used for the analysis. For fluid–solid interaction calculations, the arbitrary Lagrange–Euler approach was used. The results of the measurements are twofold. The first one is the measurement of the flow before and after vibrating plate, i.e. pure flow plate, and the second consists...
-
Local and global response of sandwich beams made of GFRP facings and PET foam core in three point bending test
PublicationIn the paper behaviour of laminated sandwich beams (FRP face sheet – PET foam core – FRP face sheet) subjected to three point bending is studied. The paper aim is to find practical descriptions enabling effective and accurate estimation of the elastic response, damage and failure of the beams, basing on experiments and static calculations. Therefore a number of tests are described, that were done on laminated coupons and foam specimens...
-
Thermal degradation of polylactic acid (PLA)/polyhydroxybutyrate (PHB) blends: A systematic review
PublicationPolylactic acid (PLA) and polyhydroxybutyrate (PHB) are two biopolyesters obtained from renewable resources like corn or sugar under bacterial fermentation. PLA is the most widely used biopolymer in diverse applications. Addition of PHB to PLA can improves the crystallinity of PLA, and thereby its mechanical strength. However, both PLA and PHB suffer from poor thermal stability, which limits their potential industrial application....
-
CERTIFICATION SYSTEM AS A TOOL FOR IMPROVING THE SAFETY AND SUSTAINABILITY OF SCHOOL-RELATED TRAVELS
PublicationDespite the well-established physical, social, emotional, cognitive, and spatial benefits of active and autonomous school commuting of children and adolescents', many are driven by car. Pilot surveys and field research held in 2019 in 10 Gdansk primary schools confirmed this trend. The article presents a certification system for schools, commissioned by the City of Gdańsk, which is an element of a systemic solution shaping patterns...
-
GTR/Thermoplastics Blends: How Do Interfacial Interactions Govern Processing and Physico-Mechanical Properties?
PublicationIn this work, GTR/thermoplastics blends (in ratio 50/50 and 75/25 wt.%) were prepared by melt-compounding in an internal mixer. During research, trans-polyoctenamer rubber (TOR), ethylene-vinyl acetate copolymer (EVA), ethylene-octene copolymer (EOC), and linear low-density polyethylene (LLDPE), were used in their thermoplastic phase. Microstructure and processing-performance property interrelationships of the studied materials...
-
Evaluation and rationale of the performance of several elastomeric composites incorporating devulcanized EPDM
Publicationthylene Propylene Diene rubber (EPDM), is present in many applications. However, its crosslinked structure makes difficult its recycling. The use of devulcanized EPDM, (dEPDM) as a component of elastomeric composites, is a real possibility to reuse EPDM scraps. In this study, three matrices (natural rubber (NR), styrene butadiene rubber (SBR) and EPDM rubber) have been tested including devulcanized EPDM as a recycled component....
-
Linear viscoelastic transversely isotropic model based on the spectral decomposition of elasticity tensors
PublicationThe linear viscoelasticity is still a useful model in the engineering for studying the behavior of materials loaded with different loading rates (frequencies). Certain types of materials reveal also an anisotropic behavior: fiber reinforced composites, asphalt concrete mixtures, or wood, to name a few. In general, researchers try to identify experimentally the dependence of engineering constants like: directional Young’s moduli...
-
Stiffness of cold-recycled mixtures under variable deformation conditions in the IT-CY test
PublicationStiffness modulus belongs to the most important properties describing the cold-recycled mixtures (CRM) in terms of their usability in road pavement structures. Previous research proved that this property is strongly dependent on the scheme and conditions of the test (temperature and time of loading) and the time that has passed since the compaction of the specimen or pavement layer. It is a result of the influence of two different...
-
Reference FEM model for SHM system of cable-stayed bridge in Rzeszów
PublicationThe paper presents the references model for structural health monitoring system (SHM) of cable-stayed bridge recently constructed in Rzeszów over Wisłok River. The SHM system is design to provide on-line information on the structure state and facilitate its maintenance procedures. The main feature of the SHM system is permanent observation of the dynamic behavior of the bridge with focus on cable vibrations. The paper discusses...
-
A method for counting people attending large public events
PublicationThe algorithm for people counting in crowded scenes, based on the idea of virtual gate which uses optical flow method is presented. The concept and practical application of the developed algorithm under real conditions is depicted. The aim of the work is to estimate the number of people passing through entrances of a large sport hall. The most challenging problem was the unpredicted behavior of people while entering the building....
-
Electrical and structural properties of Nb-doped SrTiO3
PublicationNiobium-doped strontium titanate synthesized via conventional solid-state reaction has been studied. Influence of niobium content on the lattice parameters and electrical conductivity has been reported. Various reduction conditions have been investigated. For samples reduced in hydrogen at 1400°C, a transition from thermally activated to metallic behavior has been observed. Maximum electrical conductivity (ca. 55 Scm−1 at 650°C)...
-
Application of virtual gate for counting people participating in large public events
PublicationThe concept and practical application of the developed algorithm forpeople counting in crowded scene is presented. The aim of the work is to estimatethe number of people passing towards entrances of a large sport hall. Thedetails of implemented the Virtual Gate algorithm are presented. The video signalfrom the camera installed in the building constituted the input for the algorithm.The most challenging problem was the unpredicted...
-
Theoretical analysis of the cable-stayed bridge over brda river in Bydgoszcz
PublicationThe topic of this article is the numerical analysis carried out for the cable-stayed tram (road) bridge over Brda river in Bydgoszcz. The goal of numerical studies was the verification of project assumptions and construction solutions elaborated by the autonomous team. The bridge calculations were conducted on three independent FEM models The internal forces and the elements effort under different loading schemes were examined....
-
A novel sandwich footbridge - Practical application of laminated composites in bridge design and in situ measurements of static response
PublicationA novel sandwich composite footbridge is presented in the paper, as an example of practical application of laminated composites in civil engineering. The in situ static load tests of the footbridge before its acceptation for exploitation are shown and discussed. The results are compared with the corresponding ones from a numerical equivalent single layer model of the sandwich structure created within the framework of finite element...
-
From flow to jamming: Lattice Gas Automaton simulations in granular materials
PublicationWe introduce the first extension of a Lattice Gas Automaton (LGA) model to accurately replicate observed emergent phenomena in granular materials with a special focus on previously unexplored jamming transitions by incorporating gravitational effects, energy dissipation in particle collisions, and wall friction. We successfully reproduce flow rate evolution, density wave formation, and jamming transition observed in experiments....
-
MaliciousIDE – software development environment that evokes emotions
PublicationEmotions affect every aspect of human live, including work. Numerous studies in software engineering have shown that negative emotions can lower the productivity of programmers. Unlike traditional approaches to managing software development, modern methods, such as Agile and Lean, take into account human aspects of programming. To thoroughly investigate the impact of negative emotions on the work of programmers, a malicious integrated...
-
FE analysis of support-specimen interaction of compressive experimental test
PublicationThe objective of this work is to investigate the support-specimen interaction during the compressive experimental testing of stiffened plates. The interaction is analyzed employing the nonlinear Finite Element Method using the commercial software ANSYS. The connection between the stiffened plate and testing supports is modelled with the use of contact elements, where several possible interaction scenarios are investigated, and...
-
Typologia aktywności online konsumenta w zakresie marki
PublicationWeb 2.0 daje konsumentom nieograniczone możliwości wchodzenia w interakcje, wypowiadania się, udostępniania oraz kreowania treści dotyczących produktów i marek. Tego typu aktywność konsumentów, która ma miejsce w Internecie (tzw. COBRA), stanowi wielką wartość dla firm. Niniejszy artykuł stanowi pierwszą próbę przedstawienia pełnej klasyfikacji tego typu zachowań w trzech głównych kategoriach (konsumpcji, kontrybucji i kreacji),...
-
Sanctions and their role in preventing the appropriation of the creditor’s property rights in bankruptcy proceedings–the case of Poland
PublicationThe aim of this paper is to fill the cognitive gap regarding the role of sanc-tions in the protection of a creditor’s property rights in the event of an entrepreneur insolvency. The impact of sanctions on transaction costs, including their identifica-tion and types, as well as the impact on the protection of creditor rights, has been poorly recognized in the subject literature to date. This article investigates...
-
Modelling and analysis of a synchronous generator in more electric aircraft power system using Synopsys/Saber simulator = Modelowanie i analiza generatora synchronicznego w systemie elektroenergetycznym nowoczesnego samolotu. Zastosowanie symulatora Synopsys/Saber
PublicationStreszczenie angielskie: A model for studying synchronous machine (SM) dynamic behaviour in more electric aircraft (MEA) power system is developed and implemented in the Synopys/Saber simulation environment. The modelling language MAST has been used to elaborate the SM model. The elaborated model exhibit a network with the same number of external terminals/ports as the real SM, and represents its behaviour in terms of the electrical...
-
The dependence of linear viscoelasticity limits of cold-recycled mixtures on time of curing and compaction method
PublicationCold-recycled mixtures are currently among the most widely used and investigated methods that enable recycling of old pavement structures in an environmentally friendly manner. Upon milling, the old pavement structure – whose gradation can be improved with addition of virgin aggregate – is mixed and compacted at ambient temperature. The main binding agents are bituminous emulsion and cement. Due to their dual binding behaviour,...
-
Mechanical characterization of a gravel column in a calibration chamber operating as a triaxial cell
PublicationA series of tests considering the behavior of gravel columns was performed. A segment of column with a height of 1 m and a diameter of 0.53 m was modelled in a calibration chamber used as a triaxial cell at three different lateral stress applied. The vertical load transferred on the column head was simulated with steady increase of water pressures in the upper and lower membranes. During the loading the volumetric changes in the...
-
Sensitivity analysis of simple random beam models by means of Monte Carlo Methods using Variance Reductions Techniques
PublicationA probabilistic sensitivity analysis of two nonlinear bar structures is presented. The analysis is carried out on the basis of the Monte Carlo method. The imperfections of the structures and the applied loads are adapted as random variables. Based on all of the generated input variables, an output response of the system is sought. Afterwards, a coefficient responsible for the structure failure is calculated and the limit state...
-
Low-energy positron scattering from gas-phase uracil
PublicationQuantum scattering calculations are presented for the interaction of low energy positrons with the uracil molecule, an important component of biological systems. The rotational elastic and inelastic cross sections and vibrational inelastic cross sections are reported and compared with existing experiments, indicating a general trend of the cross sections different from the experimental findings and in line with what should be expected...
-
High temperature monoclinic-to-tetragonal phase transition in magnesium doped lanthanum ortho-niobate
PublicationMagnesium doped lanthanum ortho-niobate (La0.98Mg0.02NbO4) was prepared by the molten salt synthesis method. X-ray diffraction and dilatometry methods were used to study high temperature behavior of the ceramic material. Special attention was paid to the phase transition between the monoclinic and tetragonal phases. The values of spontaneous strain on the basis of unit cell parameter, obtained by Rietveld refinement, have been...
-
Simple gait parameterization and 3D animation for anonymous visual monitoring based on augmented reality
PublicationThe article presents a method for video anonymization and replacing real human silhouettes with virtual 3D figures rendered on a screen. Video stream is processed to detect and to track objects, whereas anonymization stage employs animating avatars accordingly to behavior of detected persons. Location, movement speed, direction, and person height are taken into account during animation and rendering phases. This approach requires...
-
Failure of cold-formed beam: How does residual stress affect stability?
PublicationIn machine industry, stresses are often calculated using simple linear FEM analysis. Occasional failures of elements designed in such a way require recomputation by means of more sophisticated methods, eg. including plasticity and non-linear effects. It usually leads to investigation of failure causes and improvement of an element in order to prevent its unwanted behavior in the future. The study presents the case where both linear...
-
A Reputation Scheme to Discourage Selfish QoS Manipulation in Two-Hop Wireless Relay Networks
PublicationIn wireless networks, stations can improve their received quality of service (QoS) by handling packets of source flows with higher priority. Additionally, in cooperative relay networks, the relays can handle transit flows with lower priority. We use game theory to model a two-hop relay network where each of the two involved stations can commit such selfish QoS manipulation. We design and evaluate a reputation-based incentive scheme...
-
Dynamic Response of the Suspended on a Single Cable Footbridge
PublicationThe article presents numerical simulations, dynamic in situ load tests and a structural health monitoring (SHM) system installed in a suspended on a single cable footbridge. Numerical simulations performed prior to construction indicated the possibility of structural dynamics problems, finally confirmed in the course of dynamic test loading. In the dynamic load course the bridge deck developed vibrations displaying accelerations...
-
Characterization of Bi6Fe2Ti3O18 Ceramics with Impedance Spectroscopy
PublicationIn the present research the tool of impedance spectroscopy was utilized to characterize dielectric behavior of Aurivillius-type ceramics of Bi6Fe2Ti3O18 composition fabricated by hot pressing method from the stoichiometric mixture of oxides Bi2O3, TiO2 and Fe2O3. Impedance spectroscopy was applied to characterize dielectric response of bulk, grain boundary, and material/electrode interfaces of the fabricated polycrystalline ceramic...
-
Thermally activated persulfate-based Advanced Oxidation Processes — recent progress and challenges in mineralization of persistent organic chemicals: a review
PublicationThermally activated persulfate (TAP) finds application in Advanced Oxidation Processes for the removal of pollutants from contaminated water and soil. This paper reviewed the various cases of TAP in the environmental remediation. The pollutants such as individual pharmaceuticals, biocides, cyclic organic compounds, and dyes are considered in this review. It is interesting to note that most of the organic compounds undergo complete...
-
Ho2Pd1.3Ge2.7 – a ternary AlB2-type cluster glass system
PublicationWe report a successful synthesis of a ternary AlB2-type intermetallic compound. The phase purity was obtained by fine-tuning the Pd-Ge ratio out of the idealized 1-3. Attempts to synthesize an Er analogue were not successful. We discuss the instability of the Er analogue based on the atomic size ratio and also suggest that the increased stability of Ho2Pd1+xGe3−x in the Pd-rich range likely stems from a combination of atomic size...
-
A PRELIMINARY STUDY ON THE OPTIMAL CHOICE OF AN IMPLANT AND ITS ORIENTATION IN VENTRAL HERNIA REPAIR
PublicationThis paper addresses the problem of ventral hernia repair. The main goals are to find an optimal surgical mesh for hernia repair and to define its optimal orientation in the abdominal wall to minimise the maximum force at the tissue-implant juncture. The optimal mesh is chosen from a set of orthotropic meshes with different stiffness ratios for typical hernia placement in the abdominal area. The implant is subjected to an anisotropic...
-
Nonlinear Model of Synchronous Generator for Autonomous Electrical Power Systems Analysis
PublicationThis paper presents the nonlinear lookup table model for synchronous generator (SG) analysis. The saturation effects of the SG magnetic circuit have been considered. The saturated characteristic of the SG magnetic circuit are based on the open circuit saturation curve for magnetizing inductances. The model has been implemented into the Synopsys/Saber software using the MAST modelling language. To implement the no-load voltage characteristic...
-
Experimental Study on Pounding between Structures during Damaging Earthquakes
PublicationMutual pounding between structures during earthquakes may cause serious structural damage. The aim of this paper is to show the results of a shaking table experimental study focused on pounding between structures in series under several earthquake excitations. The experiments were performed using three tower models with different configurations and different gap distances between them. In the first stage of the study, one rigid...
-
A Centralized Reputation System for MANETs Based on Observed Path Performance
PublicationA reputation system for MANETs is described that attempts to deduce nodal trustworthiness (forwarding behaviour) from observed end-to-end path performance. The trustworthiness deduction algorithm produces interval estimates and works well if node misbehaviour is not selec-tive with respect to traversing paths. Nodal reputation levels are next calculated in the spirit of generous tit-for-tat so as to best reflect momentary nodal...
-
CONSTRUCTION TECHNOLOGY OF TIMBER-FRAME HOUSES RESISTANT TO DYNAMIC LOADS – STUDY ON MODELS OF EXTERIOR WALLS
PublicationThe aim of this paper is to show the numeric representation of experimental studies concerning the behaviour of exterior wall models of a timber-frame house under harmonic loading. A single wall model according to traditional technology of timberframe house walls (filling with mineral wool) was tested. The analysis was conducted for the following frequencies: 0.5 Hz, 1.0 Hz, 2.0 Hz and 5.0 Hz for various values of the specified...