Search results for: CHILDREN EXPOSURE
-
Evaluation of structural and electrical properties of multicomponent spinel oxide thin films deposited via spray pyrolysis technique
PublicationThis work reports the preparation of (Mn,Co,Fe,Ni,Cr)3O4 high-entropy spinel oxide in the form of a ~ 500 nm thin film utilising a facile spray pyrolysis technique. The structural and electrical properties of the layers were characterised after exposure to temperatures in the range of 400–900 ◦C. The as-deposited layers were amorphous, and crystallised upon heat treatment at 500 ◦C. Microstructural analyses proved a homogeneous...
-
Evaluation of organic coating systems for corrosion protection of industrial equipment using impedance spectroscopy
PublicationThe high economic impact of corrosion can be reduced by enhanced corrosion management and prevention based on appropriate means. This applies in particular to the protection of structures with organic protective coatings. Steel is subject to corrosion that reduces its service life and leads to destruction in most severe cases. The application of paints to metallic objects for corrosion control has been known for a long time and...
-
Just Let Me Think: Designing Against Acquired Illiteracy.
PublicationThis article concerns the relatively new problem of illiteracy relating to persons previously being literate, which is caused by too intensive using of so-called digital media (TV, computers, tablets, smartphones, e-book readers, portable media players, etc.). The problem has been observed for several years mainly in countries with high economic and technological development. The widespread use of digital media and the ease of...
-
The evaluation of eGlasses eye tracking module as an extension for Scratch
PublicationIn this paper we present the possibility of using eGlasses eye tracking module as an extension for Scratch programming tool which is a visual programming language supporting computer skills learning. The main concept behind this project is to setup the interface for rapid interaction design. Eye tracking is a powerful tool for hands free communication but for that requires a dedicated software. This software is rarely tailored...
-
Development of a new green analytical methodology for the determination of phthalates in single-use babies diapers using ultrasound-assisted extraction and polypropylene porous membrane
PublicationA green extraction strategy was developed and utilized for the extraction and determination of phthalates. The extraction is based on ultrasound-assisted extraction and a polypropylene porous membrane. The Box-Behnken model was performed to optimize the extraction condition. The optimal extraction conditions are 5.5 mL of ethyl acetate, 10 min of extraction time and 55 C for extraction temperature. The developed green extraction...
-
Amygdalin: Toxicity, Anticancer Activity and Analytical Procedures for Its Determination in Plant Seeds
PublicationAmygdalin (D-Mandelonitrile 6-O--D-glucosido--D-glucoside) is a natural cyanogenic glycoside occurring in the seeds of some edible plants, such as bitter almonds and peaches. It is a medically interesting but controversial compound as it has anticancer activity on one hand and can be toxic via enzymatic degradation and production of hydrogen cyanide on the other hand. Despite numerous contributions on cancer cell lines, the clinical...
-
Genotyping of clinical isolates of fluconazole-resistant Candida albicans
PublicationThe aim of the study was to compare the discriminatory power of RAPD-PCR method with using RSD10 primer and microsatellite analysis with using (GACA)4 primer for genotyping clinical isolates of fluconazole-resistant C. albicans. Isolates were received from patients of Children's Memorial Health Institute in Warsaw. However in the case of both tested methods low number of amplified fragments was generated, nine and six different...
-
Self-healing and shape memory polymers
e-Learning CoursesThe course "Self-Healing and Shape Memory Polymers" is a specialized elective designed for Chemical Engineering PhD students. This advanced course delves into the innovative realms of self-healing materials and shape memory polymers (SMPs), representing a significant breakthrough in material science and engineering. Throughout the course, students learn about the problems of failure of polymeric materials and explore the fundamental...
-
Determination of hormones in water samples using liquid chromatography coupled with tandem mass spectrometry
PublicationOver the past few years, many synthetic (ethinylestradiol) and natural (estradiol,estriol, estrone) compounds present in the environment have been affecting the hormonalbalance of humans and animals. Steroid hormones are very often used for medical purposesand have high estrogenic activity what makes them endocrine disrupters. Most hormonalcompounds are released into the water as a result of their incomplete removal in wastewatertreatment...
-
Sick building syndrome due to molds
PublicationThe term Sick Building Syndrome (SBS) is a combination of ailments occurring in a specific building. Building occupants complain of symptoms such as headaches and dizziness, fainting, nausea, irritation of the mucosal membranes, skin irritation and other nonspecific hypersensitivity reactions.One of the SBS causes can be molds, which are ubiquitous in the air (over 400 species). It is estimated that 30% of the health problems (related...
-
Auxetic foams
PublicationThis paper presents a method of producing auxetic polyurethane foams (PUFs) and their unique properties. The experience was based on a synthesis of traditional flexible polyurethane foam and thermal conversion to auxetic foam. The foam specimens were transformed from conventional Poisson's ratio to auxetic (negative Poisson's ratio) [1]. Basic research was performed to determine the mechanical properties and cell structure. Auxetic...
-
Silver nanoparticles induce premutagenic DNA oxidation that can be prevented by phytochemicals from Gentiana asclepiadea
PublicationAmong nanomaterials, silver nanoparticles (AgNPs) have the broadest and most commercial applications due to their antibacterial properties, highlighting the need for exploring their potential toxicity and underlying mechanisms of action. Our main aim was to investigate whether AgNPs exert toxicity by inducing oxidative damage to DNA in human kidney HEK 293 cells. In addition, we tested whether this damage could be counteracted...
-
The importance of the shape of the protein-water interface of a kinesin motor domain for dynamics of the surface atoms of the protein
PublicationSingle kinesin motor domain immersed in water has been investigated using molecular dynamics. It has been found that local properties of water in solvation shell change along with the nature of neighboring protein surface. However, a detailed analysis leads to the conclusion that the geometrical features of hydrogen bonds and overall structure of kinesin hydration water is not very different from bulk water. The local values of...
-
Mutagenic and Carcinogenic Compounds in Food
PublicationFood is a major environmental human cancer risk factor. One of the reasons for this is that food products contain substances that exhibit mutagenic and carcinogenic potential which may induce the transformation of normal somatic cells into cancerous cells. These compounds occur in food as a result of microbial contaminations (mycotoxins produced by molds), are generated from natural food components upon processing (e.g. heterocyclic...
-
Isolation and structure of a covalent cross-link adduct between mitomycin C and DNA
PublicationA DNA cross-link adduct of the antitumor agent mitomycin C (MC) to DNA has been isolated and characterized; the results provide direct proof for bifunctional alkylation of DNA by MC. Exposure of MC to Micrococcus luteus DNA under reductive conditions and subsequent nuclease digestion yielded adducts formed between MC and deoxyguanosine residues. In addition to the two known monoadducts, a bisadduct was obtained. Reductive MC activation...
-
Multi-functional sensor based on photonic crystal fiber using plasmonic material and magnetic fluid
PublicationA unique highly sensitive photonic crystal fiber is investigated based on plasmonic material and magnetic fluid (MF) for the simultaneous measurement of temperature and magnetic field sensor. The designed sensor is explored by tracing the different parameters such as birefringence, coupling length, power spectrum, and the peak wavelength of the transmission intensity. The magnetic field and temperature computation are attained...
-
The importance of the shape of the protein–water interface of a kinesin motor domain for dynamics of the surface atoms of the protein
PublicationA single kinesin motor domain immersed in water has been investigated using molecular dynamics. It has been found that local properties of water in the solvation shell change along with the nature of the neighboring protein surface. However, a detailed analysis leads to the conclusion that the geometrical features of hydrogen bonds and overall structure of kinesin hydration water are not very different from bulk water. The local...
-
Magnetic Field Generated by Short Circuit Current in the 110 kV Power System
PublicationElectric fields within tissues induced by magnetic fields including transients or short-term peaks should not be time averaged and be regarded as instantaneous values as established in the ICNIRP (International Commission on Non - Ionizing Radiation Protection) guidelines. Measurements of power lines magnetic fields with regard to human beings exposure are carried out typically with maximum current load at current balance condition...
-
An in situ technique for the assessment of adhesive properties of a joint under load
PublicationSlow crack propagation in adhesive bonded joints has been characterised using an asymmetric wedge test. Crack position was evaluated from strain gauge measurements, both in the debonded partof the joint and in the bonded zone. Test temperature was changed during loading, giving insight into bond evolution. The technique allows accurate, and virtually continuous, determination of crack position to be made, and therefore the evaluation...
-
An incorporation of contemporary daylight assessment methods into architecture and urban planning of residential areas in Poland
PublicationThis paper presents the preliminary results of the ongoing research focusing on daylight design methods for the urban planning of residential areas in Poland. The purpose of this research is to find out if modern daylight performance metrics and design methods can be beneficial to the process of urban residential planning. The paper presents a review of daylight guidelines derived from historic, Polish building regulations. A summary...
-
ROAD SAFETY MANAGEMENT TOOLS FOR COUNTRY STRATEGIC LEVEL
PublicationStrategic road safety programmes setting out long-term visions and road infrastructure development plans must be based on road safety forecasts and an understanding of the long-term impact of different measures on road safety. The objective of this paper is to discuss a concept of road safety management for an area of a selected country because there are no simple tools of road safety management for the development and implementation...
-
Home Sweet Home. Connecting the dots for healthy evening residential illumination
PublicationDuring the twentieth century, lighting designers would commonly use incandescent light sources for residential homes as they provided a visual comfort, with high quality colour rendering properties, along with relaxing ambient atmosphere. Unfortunately, it’s now difficult to buy incandescent light sources because they have been banned in many countries (https://bit.ly/2GwN2Wv). This article addresses some of the challenges in regards...
-
Evaluation of the Commercial Electrochemical Gas Sensors for the Monitoring of CO in Ambient Air
PublicationAir pollution is a growing concern of civilized world, which has a significant impact on human health and the environment. Recent studies highlight that the exposure to polluted air can increase the incidence of diseases and deteriorate the quality of life. Hence, it is necessary to develop tools for real-time air quality monitoring. For air pollution monitoring a wide range of stationary gas and particulate analysers can be used....
-
Cancer-selective, single agent chemoradiosensitising gold nanoparticles
PublicationTwo nanometre gold nanoparticles (AuNPs), bearing sugar moieties and/or thiol-polyethylene glycol-amine (PEG-amine), were synthesised and evaluated for their in vitro toxicity and ability to radiosensitise cells with 220 kV and 6 MV X-rays, using four cell lines representing normal and cancerous skin and breast tissues. Acute 3 h exposure of cells to AuNPs, bearing PEG-amine only or a 50:50 ratio of alpha-galactose derivative and...
-
Sensing the onset of epoxy coating degradation with combined Raman spectroscopy/atomic force microscopy/electrochemical impedance spectroscopy
PublicationThe paper presents the results of investigation on epoxy resin durability upon 12-week exposure to UV radiation. The aim was early determination of the onset of epoxy degradation and for this purpose an epoxy film on steel substrate systems were periodically inspected using Raman spectroscopy, atomic force microscopy and electrochemical impedance spectroscopy. The behaviour of examined polymer could be divided into three periods: immunity,...
-
Optimum Choice of Randomly Oriented Carbon Nanotube Networks for UV-Assisted Gas Sensing Applications
PublicationWe investigated the noise and photoresponse characteristics of various optical transparencies of nanotube networks to identify an optimal randomly oriented network of carbon nanotube (CNT)-based devices for UV-assisted gas sensing applications. Our investigation reveals that all of the studied devices demonstrate negative photoconductivity upon exposure to UV light. Our studies confirm the effect of UV irradiation on the electrical...
-
Corrosion monitoring as a factor increasing the safety of hydrotechnical infrastructure
PublicationWater distribution systems at KGHM S.A. are of great importance for the efficient production of copper and environmental protection. For failures leading to perforation and leakage, the corrosion processes are responsible. This paper aims to assess corrosion on the basis of the analysis of the exposure of the Hydrotechnical Plant pipelines. To this end, the system of transfer and deposition of post-flotation waste as well as the...
-
Fluctuation-enhanced and conductometric gas sensing with nanocrystalline NiO thin films: A comparison
PublicationNanocrystalline thin films of NiO were prepared by advanced reactive gas deposition, and their responses to formaldehyde, ethanol and methane gases were studied via fluctuation-enhanced and conductometric methods Thin films with thicknesses in the 200–1700-nm range were investigated in as-deposited form and after annealing at 400 and 500 °C. Morphological and structural analyses showed porous deposits with NiO nanocrystals having...
-
How to teach architecture? – Remarks on the edge of Polish transformation processes after 1989
PublicationThe political changes in Poland after 1989 have resulted in a whole range of dynamic processes including the transformation of space. Until that time the established institutional framework for spatial, urban and architectural planning policy was based on uniform provisions of the so-called planned economy. The same applied to the training of architects, which was based on a unified profile of education provided at the state’s...
-
COVID-19 and digital deprivation in Poland
PublicationResearch background: The problem of digital deprivation is already known, but the COVID-19 pandemic has highlighted its negative consequences. A global change in the way of life, work and socialisation resulting from the epidemic has indicated that a basic level of digital integration is becoming necessary. During the lockdown, people were forced to use ICTs to adapt to a rapidly changing reality. Current experience with coronavirus...
-
Long-term comparative evaluation of an acoustic climate in selected schools before and after the acoustic treatment
PublicationThe results of long-term continuous noise measurements in two selected schools are presented in the paper. Noise characteristics were measured continuously there for approximately 16 months. Measurements started eight months prior to the acoustic treatment of the school corridors of both schools. An evaluation of the acoustic climates in both schools, before and after the acoustic treatment, was performed based on comparison of...
-
IMPACT-TOUGHNESS INVESTIGATIONS OF DUPLEX STAINLESS STEELS
PublicationDuplex stainless steels are very attractive constructional materials for use in aggressive environments because of their several advantages over austenitic stainless steels. Duplex steels have excellent pitting and crevice corrosion resistance, are highly resistant to chloride stress-corrosion cracking and are about twice as strong as common austenitic steels. Better properties are associated with their microstructures consisting...
-
Synthesis of eosin modified TiO2 film with co-exposed {001} and {101} facets for photocatalytic degradation of para-aminobenzoic acid and solar H2 production
PublicationOwing to the increasing photosensitivity and DNA damage properties of para-aminobenzoic acid (PABA), concerns have been raised over the exposure of humans to PABA. Solar light-driven photocatalysis (SPC) provides a promising solution for the effective removal of organic pollutants especially when directed towards sulfate radical (SO4−) production. Herein, we have developed a sulfite-enhanced SPC using Eosin-Y sensitized TiO2/Ti...
-
COMPARISON OF NOISE EMISSION OF HCT AND CLASSIC VEHICLE COMBINATIONS FOR TIMBER TRANSPORTATION IN SWEDEN
PublicationBy means of a special simulation tool, the noise emission of a high-capacity heavy vehicle (11 axles) was compared to that of a classic heavy vehicle (a truck-dolly-semitrailer with 8 axles). The two cases are designated “Extended vehicle” versus “Classic vehicle” in this study, having total lengths of 34 and 25 m, respectively. The Classic vehicle represents the most common articulated heavy vehicle configuration for transport...
-
Evaluation of Health Hazard Due to Emission of Volatile Organic Compounds from Various Processing Units of Wastewater Treatment Plant
PublicationThe paper describes an attempt at health risk assessment and odour concentration determination in the most important units of a wastewater treatment plant. The cancer risk (CR) and hazard index (HI) parameters in selected measurement locations were calculated based on the results of chromatographic analyses (GCxGC-TOF-MS) and the United States Environmental Protection Agency (US EPA) guidelines. No exceedance of the CR and HI acceptable...
-
Road safety performance indicators and their explanatory value: A critical view based on the experience of Central European countries
PublicationCounts of road crashes and their victims represent essential information for road safety practitioners allowing them to analyse their spatial and temporal aspects. However, they cannot provide details on the factors causing road crashes. As a result, various road safety performance indicators (RSPIs) were introduced, making it possible to gather information on the effectiveness of interventions on road safety in given areas. However,...
-
Non-Gaussian Resistance Fluctuations in Gold-Nanoparticle-Based Gas Sensors: An Appraisal of Different Evaluation Techniques
PublicationVolatile organic compounds, such as formaldehyde, can be used as biomarkers in human exhaled breath in order to non-invasively detect various diseases, and the same compounds are of much interest also in the context of environmental monitoring and protection. Here, we report on a recently-developed gas sensor, based on surface-functionalized gold nanoparticles, which is able to generate voltage noise with a distinctly non-Gaussian...
-
Determination of cyanide in urine and saliva samples by ion chromatography with pulsed amperometric detection
PublicationCommonly known as a highly toxic chemical, cyanide is also an essential reagent for many industrial processes. It naturally occurs in plant seeds as a cyanogenic glycosides. Another relatively common mode of cyanide exposure is inhalation of environmental tobacco smoke. This study concerns importance to determine cyanide ion in human biological samples. Urine and saliva samples were collected healthy volunteers exposed to tobacco...
-
Visible-light-driven lanthanide-organic-frameworks modified TiO2 photocatalysts utilizing up-conversion effect
PublicationHighly efficient and quite stable composite with core-shell-like architecture reported herein, responds to the challenge of sunlight-driven photocatalysts. The Ln(ndc)/TiO2 photocatalytic system comprises active lanthanide-carboxylate coordination networks (Nd, Er, Ho, and Tm as metal ions, and 2,6-naphthalene dicar-boxylic acid as the organic linker) and inert titanium dioxide and allow to convert incompatible visible radiation...
-
Generation-recombination and 1/f noise in carbon nanotube networks
PublicationThe low-frequency noise is of special interest for carbon nanotubes devices, which are building blocks for a variety of sensors, including radio frequency and terahertz detectors. We studied noise in as-fabricated and aged carbon nanotube networks (CNNs) field-effect transistors. Contrary to the majority of previous publications, as-fabricated devices demonstrated the superposition of generation-recombination (GR) and 1/f noise...
-
Comparative Assessment of Bacteriophage and Antibiotic Activity against Multidrug-Resistant Staphylococcus aureus Biofilms
PublicationProblems connected with biofilm-related infections and antibiotic resistance necessitate the investigation and development of novel treatment strategies. Given their unique characteristics, one of the most promising alternatives to conventional antibiotics are bacteriophages. In the in vitro and in vivo larva model study, we demonstrate that phages vB_SauM-A, vB_SauM-C, and vB_SauM-D are effective antibiofilm agents. The exposure...
-
Experimental review of the performances of protective coatings for interconnects in solid oxide fuel cells
PublicationFerritic stainless steel interconnects are used in solid oxide fuel cells; however, coatings are required to improve their performance. Although several types of coatings have been proposed, they have been scarcely investigated under similar conditions. This study compares the characteristics of uncoated Crofer 22 APU and eight different coatings on Crofer 22 APU for up to 3000 h at 800 ◦C. The coatings were deposited at various...
-
Development of Safirinium dyes for new applications: fluorescent staining of bacteria, human kidney cells, and the horny layer of the epidermis
PublicationLow-molecular synthetic fluorophores are convenient tools in bioimaging applications. Several derivatives of Safirinium dyes as well as their reactive N-hydroxysuccinimide (NHS) esters bearing diverse substituents were synthesized and evaluated experimentally in terms of their lipophilicity by means of reverse-phase and immobilized artificial membrane high-performance liquid chromatography. Subsequently, the selected compounds...
-
An NO2 sensor based on WO3 thin films for automotive applications in the microwave frequency range
PublicationA microwave system dedicated to the detection of nitrogen dioxide in the harsh environment of the Norway highways is proposed. An optimized transmission line type of sensor coated with a tungsten trioxide thin film that changes its electrical properties under NO2 gas exposure is developed. The sensors' response (S) is given in °/GHz and it is calculated based on wideband measurements. The advantage of wideband measurements in comparison...
-
Assessment of organic coating degradation via local impedance imaging
PublicationThe paper presents a new approach to organic coating condition evaluation at micrometer scale using localized impedance measurements. It is based on atomic force microscopy (AFM) in contact mode. Impedance is measured between conductive AFM tip and metal substrate covered with organic coating. A single-frequency voltage perturbation signal is applied between the electrodes and current response signal is registered. As the tip is...
-
Analytical chemistry in technical approaches: immobilization of biosorbent waste containing heavy metals in cemented materials
PublicationAn ecologically safe and economically justified method of stabilization of the used biosorbents was developed. Sorbent contaminated with heavy metals has been successfully solidified/stabilized using a hydraulic binder. The test results indicated that up to 1% of the biosorbent residue used could be added without compromising the compressive strength of the mortar. The compressive strength of the modified mortars did not change...
-
Do You Know What You Drink? Comparative Research on the Contents of Radioisotopes and Heavy Metals in Different Types of Tea from Various Parts of the World
PublicationThe aim of this study was to assess the potential health risks of radioactive elements and heavy metals ingested through the consumption of various types of tea imported to the Polish market (black, green, red, oolong and white). The concentrations [Bq/kg] of radionuclides (40K, 137Cs, 226Ra, 210Pb and 228Th) in tea leaves before and after brewing were measured using γ-ray spectrometry with high-purity germanium (HPGe). The concentrations...
-
An investigation of selected monoaromatic hydrocarbons released from the surface of polystyrene lids used in coffee-to-go cups
PublicationA consumer trend towards the fast preparation of beverages has increased the popularity of hot beverages (especially coffee and tea) available in disposable containers called coffee-to-go cups with fitted polystyrene lids. Lids in contact with hot beverages may release low molecular weight organic compounds into the gaseous phase causing direct exposure of consumers to these compounds during drinking. The paper describes in detail...
-
Effect of Some Sulphur Additives on The Degradation of 9Cr-1Mo Steel After Its 10 Years Service in The CCR Platforming Unit
PublicationThe work shows the results of the tests of 9Cr-1Mo steel, which was for 10 years operated in the CCR platforming unit in Group Lotos SA in Gdańsk, and then in the laboratory was sulphidised during 166 h at a temperature of 600 °C. Sulphidation was performed in a mixture of H2-H2S gases at the vapour pressure of sulphur 4.1·10-14 atm, so the order of magnitude of vapour pressure was less than that of the dissociation pressure of...
-
Degradation of electrical performance of a crystalline photovoltaic module due to dust deposition in northern Poland
PublicationThe reduction in power output caused by the accumulation of dust on the photovoltaic module surface is an important problem and should receive much more attention in the literature. This study was an evaluation of the performance degradation of crystalline photovoltaic modules due to natural and simulated dust deposition. Dust is created from powdered grains of sand and particles of different bodies. Dust originates from different...