Filters
total: 2401
displaying 1000 best results Help
Search results for: CONVENIENCE VOTING
-
Person Tracking in a Ferry Environment Using Ultra-Wide Band Radio Interface
PublicationThis article presents research and analysis of effectiveness of tracking moving people in an environment of passenger ferry, using measurements of propagation time of ultra-wide band radio signal (UWB - Ultra-Wide Band). Constructed measurement stand and results of measurements carried out in a real propagation conditions were shortly discussed.
-
Analysis of unsteady flow forces on the thermowell of steam temperature sensor
PublicationIn this paper, 3D numerical analysis of unsteady flow forces acting on the measuring sheath of steam temperature is presented. According to that purpose, the CFD (Computation Fluid Dynamic [1]) approach has been used. The nonstationary of fluid acting on the measuring sheath such as: Strouhal frequency, amplitude of pressure, structure of vortex, peak of pressure, field of pressure, field of velocity etc. are studied analytically...
-
Design and distribution of air nozzles in the biomass boiler assembly
PublicationDue to energy crisis as well as increasing pollution of the environment, renewable energy sources usage increases all over the world. These facts encouraged authors to start research over developing a uniform biomass boiler calculation model. This paper presents a design of biomass boiler assembly created for ORC (Organic Rankine Cycle) unit since these systems could achieve strong position in energy industry....
-
On jump conditions at non-material singular curves in the resultant shell thermomechanics
PublicationThe global, refined, resultant, two-dimensional (2D) balance laws of mass, linear and angular momenta, and energy as well as the entropy inequality were formulated by Pietraszkiewicz (2011) as exact implications of corresponding laws of 3D rational thermomechanics. In case of a shell with the regular base surface and all resultant surface fields differentiable everywhere on it and at any time instant, the local laws of the resultant...
-
Influence of permanent magnetic field on wear performance of dry sliding contacts
PublicationResults of experimental studies concerning the influence of permanent magnetic field on wear of dry sliding contact are presented.It was found that magnetic field of horizontal orientation is causing temporary reduction of material's hardness. It also facilitates and accelerates removal process of wear particles from the contact zone.Formation of bulges, consisting of accumulated and compacted anti-ferromagnetic material produced...
-
Simulation model for evaluation of packet sequence changed order of stream in DiffServ network
PublicationCurrent packet networks use a large variety of mechanisms which should support QoS (Quality of Service). One of those mechanisms is routing (calculating connection paths for incoming service requests). The most effective mechanism in QoS context is dynamic routing, which is based on the current network state described by the offered traffic matrix and link states. After switching between calculated available paths, connection...
-
Dynamics of fault arc traveling along busbars in high voltage switchboards = Dynamika łuku zwarciowego przemieszczającego się wzdłuż szyn rozdziel-nic wysokiego napięcia
PublicationThe paper presents the results of magnetic induction and electrodynamic force calculations acting on arc column during short-circuit in medium voltage air-insulated bus-bars. The gap between the bars was 120 mm and the prospective short-circuit currents ranged from 4 kA to 8 kA. The paper also shows the measurement results of average velocity fault arc depending on currents arc diameter and arc current was established and described....
-
Titania Nanotubes/Hydroxyapatite Nanocomposites Produced with the Use of the Atomic Layer Deposition Technique: Estimation of Bioactivity and Nanomechanical Properties
PublicationTitanium dioxide nanotubes/hydroxyapatite nanocomposites were produced on a titanium alloy (Ti6Al4V/TNT/HA) and studied as a biocompatible coating for an implant surface modification. As a novel approach for this type of nanocomposite fabrication, the atomic layer deposition (ALD) method with an extremely low number of cycles was used to enrich titania nanotubes (TNT) with a very thin hydroxyapatite coating. X-ray diffraction (XRD)...
-
Electrochemical Activity and Electrical Properties of Optimized Polypyrrole Coatings on Iron
PublicationIn this work, electrochemical activity and electrical properties of polypyrrole (PPy) coated iron electrodes have been investigated. PPy film was electrochemically polymerized from sodium salicylate aqueous solution under conditions, which provided an increase of iron corrosion resistance. It was noticed that the pH of the solution and the applied electrode potential range during the study of the polymer properties had an influence...
-
Radio Channel Measurements in 868 MHz Off-Body Communications in a Ferry Environment
PublicationIn this paper, a characterization of the 868 MHz off-body radio channel in BANs is presented. Measurements were carried out in a ferry environment using a specific set-up. A method for path loss using radio distance measurements (RDMs) was developed. It allows to automate the measurements process and make it independent from the variable speed of a moving person. Based on the observed path loss as a function of distance, the obtained...
-
Influence of Gd deposition on the oxidation behavior and electrical properties of a layered system consisting of Crofer 22 APU and MnCo2O4 spinel
PublicationIn the study, the surface of the Crofer 22APU ferritic steel was modified with gadolinium oxide nanoparticles and a protective-conducting layer consisting of the MnCo2O4 spinel. This system was studied in the context of application in IT-SOFC interconnects. Four types of samples were studied: unmodified steel, steel coated with a manganese-cobalt spinel layer, steel modified with gadolinium oxide nanoparticles, and a system consisting...
-
Ferrofluids based analytical extractions and evaluation of their greenness
PublicationFerrofluids are stable dispersions of magnetic nanoparticles in a carrier liquid. They have attracted considerable attention in analytical extractions as they combine fluid-like properties with magnetic character, providing magnetic control over the extraction process. The synthesis of ferrofluids is very straightforward, and it generally involves the preparation of magnetic nanoparticles, their coating, and then mixing in a suitable...
-
Rural Design Studio
e-Learning CoursesThis design studio aims to ensure that new development in the countryside does not detrimentally affect its setting and is appropriate in terms of design, scale, siting and character.The workshop aims to promote development which compliments rural landscape character; reconciling the requirements of a modern lifestyle with the principles underpinning traditional rural development while promoting “distinctive”, good quality, contemporary...
-
Rural Design Studio - 2023
e-Learning CoursesThis design studio aims to ensure that new development in the countryside does not detrimentally affect its setting and is appropriate in terms of design, scale, siting and character.The workshop aims to promote development which compliments rural landscape character; reconciling the requirements of a modern lifestyle with the principles underpinning traditional rural development while promoting “distinctive”, good quality, contemporary...
-
Road texture influence on tire rolling resistance
PublicationTire rolling resistance is one of the most important resistive forces acting on road vehicles. It depends on tire and surface characteristics as well as vehicle operating parameters. This paper deals with the influence of road surface texture on rolling resistance of passenger car tires. Results of road measurements performed on variety of road surfaces are presented.
-
New Method for Increasing Precision of Position Estimation in Hybrid Inertial Navigation System
PublicationIn article new method for increasing precision of position estimation by using inertial navigation in hybrid localization system with reduced number of reference nodes for radio distance measurements was presented. Measuring campaign using developed measuring stand were carried out to verify precision of position estimation of moving person in indoor environment.
-
Current air quality analytics and monitoring: A review
PublicationThis review summarizes the different tools and concepts that are commonly applied in air quality monitoring. The monitoring of atmosphere is extremely important as the air quality is an important problem for large communities. Main requirements for analytical devices used for monitoring include a long period of autonomic operation and portability. These instruments, however, are often characterized by poor analytical performance....
-
Searching of the buried objects into the sea bottom by means of nonlinear acouctic methods
PublicationThe main goal of this paper is to introduce the methodology of preparing the area for investigations that will be carried out at the sea. As the first step there is recognition of the basic method both in the theory as well as experimental investigation. There were taken into account the nonlinear methods. These ones are very promising methods that have very interesting features, very convenient for examinations of the seabed structure....
-
Monosubstituted hydrazone β-cyclodextrin derivatives for pH-sensitive complex formation with aromatic drugs
PublicationA new and convenient synthetic pathway was developed to produce monosubstituted cyclodextrins with high yields. Each of the β-cyclodextrin derivatives described in this work has an aromatic substituent connected with cyclodextrin core by a pH-sensitive hydrazone linker and a carbon chain. Carbon chains differ in lengths having one or three carbon atoms. The correlation between water solubility and linker length was determined using...
-
THE IMPACT OF GROUND TIRE RUBBER TREATMENT ON THE THERMAL CONDUCTIVITY OF FLEXIBLE POLYURETHANE/GROUND TIRE RUBBER COMPOSITES
PublicationWaste car tires are burdensome waste, and their utilization is crucial for the natural environment. In many countries, the primary method of their recycling is energy recovery, performed by simple combustion. However, material recycling is much more effective and significantly more beneficial for the natural environment. It results in the generation of ground tire rubber, which can be used to produce polymerrubber composites. It...
-
BLOOD PRESSURE ESTIMATION BY MEANS OF A JOINT IMPEDANCE– PHOTOPLETYSMOGRAPHIC METHOD
PublicationThe knowledge of patient’s day to day blood pressure changes is invaluable to physicians for both diagnostics and health monitoring reasons. Constant observation of the pressure throughout a day would provide even more valuable clinical information. A convenient non-invasive methods of blood pressure estimation for monitoring purposes are widely proposed. This work shows a statistical approach to...
-
Complete input data to CFD 3D model of combustion in the large marine 4-stroke engine
Open Research DataInput data to CFD and 3D model of combustion process for large marine 4-stroke diesel engine.
-
Anna Danuta Dettlaff dr inż.
PeopleShe received her Master of Science degree in engineering with honours in 2013 at the Gdańsk University of Technology at the Department of Analytical Chemistry. In 2013-2017, she was a PhD student in the field of Chemical Technology at Faculty of Chemistry. Her doctoral dissertation was entitled “Nanocomposites based on conducting polymer and carbon materials for supercapacitor application”. In 2015, she was doing a three-month...
-
Raz jeszcze o obciążeniu hydrodynamicznym falochronu pionowościennego falą stojącą
PublicationPrzedstawienie istniejących modeli matematycznych opisujących rozkłady ciśnienia hydrodynamicznego na falochron pionowościenny w wyniku oddziaływania fali stojącej. Analiza nieciągłości ciśnienia. Jakościowe porównanie metod obliczeniowych dla wybranych warunków wodno-falowych.
-
Reduced-Cost Microwave Design Closure by Multi-Resolution EM Simulations and Knowledge-Based Model Management
PublicationParameter adjustment through numerical optimization has become a commonplace of contemporary microwave engineering. Although circuit theory methods are ubiquitous in the development of microwave components, the initial designs obtained with such tools have to be further tuned to improve the system performance. This is particularly pertinent to miniaturized structures, where the cross-coupling effects cannot be adequately accounted...
-
Tax discount for children deducted from income in selected EU countries, available according to the criterion of the number of children (in EUR) in 2017
Open Research DataDespite the far-reaching harmonization of collection mechanisms and the amount of VAT and excise duty rates in the European Union, individual countries, as a rule, conduct individual income tax policies, including a system of reliefs and exemptions. It is worth noting that, as shown below, each European Union country uses at least one method of supporting...
-
Comparison of properties of the new electro-mechanical model and circumferential model of the inductive-dynamic drive
PublicationThe article presents a new electromechanical model of inductive-dynamic drive. The model is implemented in two environments: Maxwell for analyzing electrodynamic phenomena including moving of the disc and Ansys which allows for stress analysis on the basis of the volume forces imported from Maxwell. Additionally, a model validation by comparing with the existing circumferential model was carried out.
-
Influence of the thermal modernization of window on transmission heat losses
PublicationThe article presents the results of calculations of the heat transfer coefficient for the state before and after renovation for the historic windows. The aim of the analysis was to obtain the values of thermal insulation parameters demanded by the regulations, while not losing the historical value of the window. The described example of the renovation of the existing window consisted in installing an additional window panel from...
-
Przegląd metod wyznaczania parcia mieszanki betonowej na deskowanie
PublicationW pracy poruszono tematykę wyznaczania parcia mieszanki betonowej na deskowanie. Zebrano i opisano wybrane cztery modele stosowane do wyznaczania rozkładu ciśnienia poziomego świeżej mieszanki betonowej oddziaływującej na deskowanie. Dokonano krótkiego przeglądu literatury z zakresu omawianej tematyki parcia mieszanki betonowej na deskowanie.
-
Morphology and local chain structure of polyamide 6 modified in the solid state with a semi-aromatic nylon salt
PublicationStructural and conformational differences between the polyamide 6 (PA6) homopolymer and two copolymers of PA6 modified in the solid state with 20 and 30 wt% of the semi-aromatic nylon salt of 1,5-diamino-2-methylpentane (Dytek A) and isophthalic acid (IPA) in the feed were investigated. Room temperature wide-angle X-ray diffraction (WAXD) analysis together with 13C{1H} cross-polarization/magic-angle spinning solid-state (CP/MAS)...
-
Suitability study of hybrid model of electrodynamic actuator
PublicationThis paper presents the proposal of the hybrid circuit-field model of an electrodynamic actuator. The field model uses the inductor current as the input data which is obtained from the circuit model or experimentally. The field model implemented using the FLUX program makes it possible to easily determine the pressure distribution acting on the disc. The results have been verified experimentally.
-
Experimental investigation into surface texture effect on journal bearings performance
PublicationThe aim of this study was to analyse the performance of journal bearings with specially created dimples on the sliding surface and operating under various conditions. The texture was created on the bearing surface that co-acted with the smooth journal; moreover, the variation of the textured surface of the journal mating with the smooth bearing was tested, and the results were compared to those obtained with the standard smooth...
-
Research and Analysis of Accuracy of Location Estimation in Inertial Navigation System
PublicationIn the article the research and analysis of digital signal processing and its influence on accuracy of location estimation in developed inertial navigation system was presented. The purpose of the system is to localize moving people in indoor environment. During research a measuring unit for recording selected movement parameters was made. In the article were also described author’s inertial navigation algorithms.
-
Wpływ stopowania laserowego z użyciem nanorurek węglowych stopu Ti13Nb13Zr do zastosowań biomedycznych na jego wybrane własności mechaniczne
PublicationDo eksperymentu użyto stopu tytanu Ti13Nb13Zr, który ze względu na swój skład chemiczny i właściwości mechaniczne stanowi materiał do zastosowań w inżynierii medycznej. Celem pracy była ocena wpływu stopowania laserowego stopu Ti13Nb13Zr z powłoką z wielościennych nanorurek węglowych na jego właściwości mechaniczne (chropowatość, nanotwardość, moduł Younga). Do wytworzenia powłoki węglowej wykorzystano metodę osadzania elektroforetycznego (EDP)....
-
Exhaust gas temperature measurements in diagnostic examination of naval gas turbine engines. Part III. Diagnostic and operating tolerances
PublicationThe third part of the article presents a method for detecting failures of the automatic engine control system with the aid of an exhaust gas temperature setter, specially designed and machined for this purpose. It also presents a procedure of identifying the operating tolerances and determining the diagnostic tolerances for the exhaust gas temperature recorded in the naval turbine engine during the start-up and acceleration processes....
-
On the Limiting Distribution of Lempel-Ziv’78 Redundancy for Memoryless Sources
PublicationWe study the Lempel-Ziv'78 algorithm and show that its (normalized) redundancy rate tends to a Gaussian distribution for memoryless sources. We accomplish it by extending findings from our 1995 paper, in particular, by presenting a new simplified proof of the central limit theorem (CLT) for the number of phrases in the LZ'78 algorithm. We first analyze the asymptotic behavior of the total path length in the associated digital search...
-
An Improved Convolutional Neural Network for Steganalysis in the Scenario of Reuse of the Stego-Key
PublicationThe topic of this paper is the use of deep learning techniques, more specifically convolutional neural networks, for steganalysis of digital images. The steganalysis scenario of the repeated use of the stego-key is considered. Firstly, a study of the influence of the depth and width of the convolution layers on the effectiveness of classification was conducted. Next, a study on the influence of depth and width of fully connected...
-
Convex set of quantum states with positive partial transpose analysed by hit and run algorithm
PublicationThe convex set of quantum states of a composite K×K system with positive partial transpose is analysed. A version of the hit and run algorithm is used to generate a sequence of random points covering this set uniformly and an estimation for the convergence speed of the algorithm is derived. For K >3 or K=3 this algorithm works faster than sampling over the entire set of states and verifying whether the partial transpose is positive....
-
Simplified method of applying loads to flat slab floor structural model
PublicationThe article analyses the impact of the live load position on the surface of a reinforced concrete flat slab floor of 32.0 m × 28.8 m. Four variants of a live load position are investigated: located on the entire concrete slab, set in a chessboard pattern, applied by bands and imposed separately in each of the slab panels. Conclusions are drawn upon differences in bending moments, the time of calculation and the size of output files....
-
Iterative‐recursive estimation of parameters of regression models with resistance to outliers on practical examples
PublicationHere, identification of processes and systems in the sense of the least sum of absolute values is taken into consideration. The respective absolute value estimators are recognised as exceptionally insensitive to large measurement faults or other defects in the processed data, whereas the classical least squares procedure appears to be completely impractical for processing the data contaminated with such parasitic distortions. Since...
-
A simple and efficient hybrid discretization approach to alleviate membrane locking in isogeometric thin shells
PublicationThis work presents a new hybrid discretization approach to alleviate membrane locking in isogeometric finite element formulations for Kirchhoff–Love shells. The approach is simple, and requires no additional dofs and no static condensation. It does not increase the bandwidth of the tangent matrix and is effective for both linear and nonlinear problems. It combines isogeometric surface discretizations with classical Lagrange-based...
-
Productivity effects of trade in natural resources—comparison with mechanisms of technological specialisation
PublicationThis paper compares two alternative growth paths, assessing the effects on productivity of specialisation in natural resources (NR) and in technologically advanced products. The empirical analysis exploits product-level export data for 109 developing and 51 developed economies over the period 1996–2018. We document two distinct types of specialisation, based on exports either of natural resources or of technological products, and...
-
The Importance of Demand and Environment for Defining and Establishing the Role of Data Stewards
PublicationData stewardship is now a central part of FAIR research data management. Although various types of positions called data stewards have been created at academic institutions over the last years, no demand-oriented, formal model of data stewardship and the associated roles exist so far. This workshop report presents the outcomes of the panel discussion “The Importance of Demand and Environment for Defining Data Stewardship” held...
-
Proximal primal–dual best approximation algorithm with memory
PublicationWe propose a new modified primal–dual proximal best approximation method for solving convex not necessarily differentiable optimization problems. The novelty of the method relies on introducing memory by taking into account iterates computed in previous steps in the formulas defining current iterate. To this end we consider projections onto intersections of halfspaces generated on the basis of the current as well as the previous...
-
Ferromagnetic nanoparticles imaging by means of Magnetic Force Microscopy
Open Research DataFerromagnetic nanoparticles can be used as building blocks for advanced thin film magnets, and can also be used in data storage and biomedical technologies. Nano-crystalline ferrites with the chemical formula NixZn (1 - x) Fe2O4, where x = 0, 0.2, 0.4, 0.6, 0.8, 1.0 show anti-corrosion properties and suppress electromagnetic interference, in the case...
-
Frequency response spectra applied to assess efficiency of the training techniques
PublicationThe purpose of the research is to assess the increase of the muscle strength and power. Movement of the human body when the moving one impacts a stationary or moving body is taken under consideration. The waveform produced by an impact is transformed into frequency domain. The acceleration record is transformed as a complex spectrum, by the use of a Discrete Fourier Transformation. In this paper the applications of the discrete...
-
Distributed Framework for Visual Event Detection in Parking Lot Area
PublicationThe paper presents the framework for automatic detection of various events occurring in a parking lot basing on multiple camera video analysis. The framework is massively distributed, both in the logical and physical sense. It consists of several entities called node stations that use XMPP protocol for internal communication and SRTP protocol with Jingle extension for video streaming. Recognized events include detecting parking...
-
Shipping Low Frequency Noise and Its Propagation in Shallow Water
PublicationOne of the most significant factor influencing acoustical climate of the sea is underwater noise generated by moving ships. If the considered sea area has features of the shallow water, namely the wave frequency fulfils relation f < 10c/h, where c denotes phase speed of sound, and h is depths of the sea, then in certain distance from the wave source specific image of sound pressure distribution in the mean of wave modes appears....
-
Centrally Pivoted Tilting Pad Thrust Bearing with Carbon-Based Coated Collar—Experimental Results of Low- and Medium-Speed Operation
PublicationExperimental results of the research on a tilting pad thrust bearing with symmetrical pad support in the conditions of high loads and low speeds are presented in the paper. As described in the literature review, experimental results of tilting pad bearings at low speed/high load regime and transient conditions are rare. Unusual material selection - steel pad against a DLC-type coating on the collar was utilized. Such material combination...
-
Vehicular Communication Environments
PublicationCommunication to and between road vehicles (cars, truck, buses, trains, etc.) are of growing interest. This is partly due to the attractive services that cooperative intelligent transport systems (C-ITSs) provides, mainly in the areas of traffic safety and traffic efficiency. An enabler for C-ITS is wireless vehicle-to-vehicle (V2V) and vehicle-to-infrastructure (V2I) communication, collectively referred to as vehicle-to-X (V2X)...