Filters
total: 3675
filtered: 2373
displaying 1000 best results Help
Search results for: moderate%20temperature
-
Tripping of F-type RCDs for sinusoidal residual current with superimposed smooth DC component
PublicationRecent trends in green energy development make that photovoltaics and electric vehicles are applied on an increasing scale. In both photovoltaic and electric vehicle charging installations, a significant value of DC component of the earth fault current may appear, which is a challenge, in particular, for commonly used residual current devices (RCDs). This paper presents results of the laboratory test on the operation of F-type...
-
Spectroscopic study of atmospheric pressure 915 MHz microwave plasma at high argon flow rate
PublicationIn this paper results of optical emission spectroscopic (OES) study of atmospheric pressure microwave 915 MHz argon plasma are presented. The plasma was generated in microwave plasma source (MPS) cavity- resonant type. The aim of research was determination of electron excitation temperature Texc gas temperature Tg and electron number density ne. All experimental tests were performed with a gas flow rate of 100 and 200 l/min and...
-
Effects of deviations from thermo-rheologically simple behavior of asphalt mixes in creep on developing of master curves of their stiffness modulus
PublicationThe paper presents the deviations from the thermo-rheologically simple behavior of asphalt mixes and their effects on the developing of master curves of stiffness modulus. Eleven different mixes were tested in three point bending test under constant load at temperatures –20°C, –10 °C and 0 °C, and in some cases at +10 °C. The test method was developed at the Gdansk University of Technology, Poland. The applied stress level was...
-
EFFECT OF SURFACE STATE AND STRESS ON AN OXIDATION OF THE ZIRCALOY-2 ALLOY
PublicationZr alloys are widely used as materials for nuclear fuel pellets in the nuclear industry. In the case of the LOCA or RIA happen, a temperature may locally reach high values. Even if the high temperature maintains shortly, the zirconium oxides may become permeable, absorb hydrogen appearing in cooling water from decomposition reaction and crack because of formation and brittle failure of hydrides. Such model cannot so far take into...
-
Eksperymentalna weryfikacja procedury szacowania wytrzymałości młodego betonu wg normy ASTM C1074
PublicationW referacie przedstawiono metodę służącą oszacowaniu wytrzymałości betonu w trakcie procesu dojrzewania (ang. Maturity Method) bazującą na procedurze określonej zgodnie z amerykańską normą, która uwzględnia wpływ połączonych efektów temperatury i czasu na rozwój wytrzymałości betonu. Standardy ASTM C1074 zostały opracowane przez NBS (ang. National Bureau of Standards) z uwagi na powtarzające się wypadki na palcu budowy wynikające...
-
Simulation of Direct-Sequence Spread Spectrum Data Transmission System for Reliable Underwater Acoustic Communications
PublicationUnderwater acoustic communication (UAC) system designers tend to transmit as much information as possible, per unit of time, at as low as possible error rate. It is a particularly difficult task in a shallow underwater channel in which the signal suffers from strong time dispersion due to multipath propagation and refraction phenomena. The direct-sequence spread spectrum technique (DSSS) applied successfully in the latest standards...
-
Influence of the ionic strength on the amyloid fibrillogenesis of hen egg white lysozyme
PublicationThe study investigates the role of the electrostatic interactions in the fibrillation of the hen egg white lysozyme (HEWL). In order to achieve this aim the influence of the cations Na+, Mg2+ and Al3+ on the amyloid fibril formation and amorphous aggregation was tested. The amyloids are formed in the solution without added salt but the Thioflavin T fluorescence gives the false-negative result. In these conditions, the HEWL fibrils...
-
Detection, classification and localization of acoustic events in the presence of background noise for acoustic surveillance of hazardous situations
PublicationEvaluation of sound event detection, classification and localization of hazardous acoustic events in the presence of background noise of different types and changing intensities is presented. The methods for discerning between the events being in focus and the acoustic background are introduced. The classifier, based on a Support Vector Machine algorithm, is described. The set of features and samples used for the training of the...
-
Realistic noise-tolerant randomness amplification using finite number of devices
PublicationRandomness is a fundamental concept, with implications from security of modern data systems, to fundamental laws of nature and even the philosophy of science. Randomness is called certified if it describes events that cannot be pre-determined by an external adversary. It is known that weak certified randomness can be amplified to nearly ideal randomness using quantum-mechanical systems. However, so far, it was unclear whether randomness amplification...
-
Bacterial cellulose in the field of wound healing and regenerative medicine of skin: recent trends and future prospectives
PublicationIn this overview, we focused on the bacterial cellulose (BC) applications, described in recently published scientific papers, in the field of skin regenerative medicine and wound care industry. Bacterial cellulose was proven to be biocompatible with living tissues. Moreover, its mechanical properties and porous structure are considered to be suitable for biomedical applications. It is due to the fact that porous structure of bacterial...
-
The Role of Inflammatory Cytokines in the Pathogenesis of Colorectal Carcinoma-Recent Findings and Review
PublicationThe inflammatory process plays a significant role in the development of colon cancer (CRC). Intestinal cytokine networks are critical mediators of tissue homeostasis and inflammation but also impact carcinogenesis at all stages of the disease. Recent studies suggest that inflammation is of greater importance in the serrated pathway than in the adenoma-carcinoma pathway. Interleukins have gained the most attention due to their...
-
Superconductivity in the intermetallic compound Zr5Al4
PublicationPolycrystalline Zr5Al4 was synthesized using the arc-melting method. Powder X-ray diffraction confirms the previously reported crystal structure of the Ti5Ga4-type P63/mcm with lattice parameters: a = 8.4312(6) A , and c = 5.7752(8) A . Electrical resistivity and low-temperature magnetic susceptibility measurements indicate that Zr5Al4 exhibits superconducting behavior below 2 K. The normalized heat capacity jump at Tc= 1.82 K...
-
On the production of electricity in Poland using a geothermal binary power plant - A thermodynamic overview - Part I
PublicationPoland has a significant potential of geothermal energy. However, the high-temperature sources that are needed to drive power plants are found in relatively few places. Therefore, the objective of this paper is to consider any location in the northern part of Poland as a possible place to build a binary power plant. A scientific research was confirmed the existence of an elevated temperature gradient in this region. The hot rocks...
-
Comparison of Downdraft and Updraft Gasification of Biomass in a Fixed Bed Reactor
PublicationThe aim of this study was to compare and analyze the gasification process of beech wood. The experimental investigation was conducted inside a gasifier, which can be operated in downdraft and updraft gasification system. The most important operating parameter studied in this paper was the influence of the amount of supply air on the temperature distribution, biomass consumption and syngas calorific value. The results show that...
-
The psychrotrophic yeast Sporobolomyces roseus LOCK 1119 as a source of a highly active aspartic protease for the in vitro production of antioxidant peptides
PublicationA psychrotrophic yeast strain producing a cold-adapted protease at low temperature was classified as Sporobolomyces roseus. In standard YPG medium, S. roseus LOCK 1119 synthesized an extracellular protease with an activity of approximately 560 U/L. Optimization of medium composition and process temperature considerably enhanced enzyme biosynthesis; an approximate 70% increase in activity (2060 U/L). The native enzyme was purified...
-
Modeling and MANOVA studies on toxicity and endocrine potential of packaging materials exposed to different extraction schemes
PublicationThe stability of the linings of packaging that is in contact with the goods stored has been of major concern during decades of the development of packaging materials. In this work, an attempt was undertaken to assess the applicability of using two bioassays (Microtox® and XenoScreen YES/YAS) in estimating the stability of packaging (cans, caps, multilayer material) and the impact of their degradation on the toxicity of some simulated media....
-
Effect of isovalent substitution on microstructure and phase transition of LaNb1−xMxO4 (M=Sb, V or Ta; x=0.05–0.3)
PublicationLaNb1−xMxO4 oxides with pentavalent elements of different ionic sizes (M=Sb, Ta and V, x=0.05–0.3) were synthesized by the solid state reaction method. Special interest was devoted to the antimony substituted lanthanum niobate which is a new material in this group. Rietveld analysis of the X-ray diffraction patterns was used to determine the influence of the material composition on unit cell parameters. On the basis of dilatometric...
-
Jeffreys heat conduction in coupled semispaces subjected to interfacial heating
PublicationA Jeffreys heat conduction problem for coupled semispaces subjected to the action of an interfacial heat source was defined. An analytical solution of the problem was derived for a polynomial specific power of the heat source using the Laplace transform approach. The asymptotic and parametric analysis was performed for different ratios of thermal conductivities , thermal diffusivities , thermal relaxation times and coefficients...
-
Intergranular Corrosion Detection Using Electromagnetic Transducers for Ultrasonic Testing
PublicationThe aim of this paper is to create a research methodology that allows a quick analysis of the structural state of high alloy austenitic steels using non-destructive ultrasonic tests, in contrast to destructive standard methods. Electromagnetic acoustic transducers (EMAT) are used to generate and receive the ultrasonic wave and detect the microstructural changes caused by sample sensitization in elevated temperature, even after...
-
The homometallic warwickite V 2 OBO 3
PublicationThe synthesis, structure and elementary magnetic characterization of the homometallic warwickite V2OBO3 are reported. The material adopts the orthorhombic warwickite structure type at room temperature, space group Pnma (No. 62) with lattice parameters a = 9.2317(1) Å, b = 3.1172(1) Å, and c = 9.5313(1) Å. Temperature-dependent magnetic susceptibility, electrical resistivity, and specific heat measurements show anomalies near 35 K,...
-
On thermal stability of topological qubit in Kitaev's 4D model
PublicationWe analyse stability of the four-dimensional Kitaev model-a candidate for scalable quantum memory - in finite temperature within the weak coupling Markovian limit. It is shown that, below a critical temperature, certain topological qubit observables X and Z possess relaxation times exponentially long in the size of the system. Their construction involves polynomial in system size algorithm which uses as an input the results of...
-
The innovative experimental rig for wood steam drying at atmospheric pressure
PublicationThe high cost of fossil fuel and soaring consumer interest have encouraged people in the wood industry to look for faster and more energy-efficient methods to dry lumber. The air-steam mixture as medium of drying process was used in a laboratory kiln especially arranged for that reason. Experimental rig is based on automatic control system. At the time of drying measurements of the internal temperature, wood temperature, moisture...
-
Interactions between components of SrTi0.98 Nb0.02O3-δ-YSZ and SrTi0.98 Nb0.02O3-δ -CeO2 composites
PublicationComposites consisting of SrTiO3-based perovskite and either yttria-stabilized zirconia or ceria were investigated. The mechanical compatibility and possible inter-diffusion between phases were characterized by scanning electron microscopy, X-ray diffraction, and energy-dispersive X-ray spectroscopy. A gradual disappearance of Ce-containing phases with an increase in the temperature of reduction in hydrogen was noticed. Moreover,...
-
Electrical conductivity and relaxation processes in V2O5 nanorods prepared by sol–gel method
PublicationProperties of high purity V2O5 nanorods prepared by a sol – gel method are presented. The studied materials were characterized by: X-ray diffractometry (XRD), scanning electron microscopy (SEM), and X-ray photoelectron spectroscopy (XPS). The electrical impedance was measured as a function of temperature and frequency. The obtained results show that the electrical conductivity increases with increasing temperature. The d.c. conductivity...
-
Vibrational Properties of LaNb0.8M0.2O4-δ (M=As, Sb, V, and Ta)
PublicationLaNb0.8M0.2O4-δ (where M=As, Sb, V, and Ta) oxides with pentavalent elements of different ionic sizes were synthesized by a solid-state reaction method. The vibrational properties of these oxides have been investigated. These studies revealed that the substituent element influences both Debye temperature value as well as the Raman active vibrational modes. Additionally, the low-temperature vibrational properties of LaNb0.8Sb0.2O4-δ...
-
ATTEMPTS OF THERMAL IMAGING CAMERA USAGE IN ESTIMATIONS OF THE CONVECTIVE HEAT LOSS FROM A VERTICAL PLATE
PublicationIn this paper a new method for determining heat transfer coefficients using a gradient method has been developed. To verify accuracy of the proposed method vertical isothermal heating plate with natural convection mechanism has been examined. This configuration was deliberately chosen, because of the fact that such case is historically the earliest and most thoroughly studied and its rich scientific documentation - the most reliable....
-
Polymer based thick films - material quality and interface resistance evaluation
PublicationThe properties of polymer based thick film layers mede using different resistive pastes and dipping silvers have been studied. The composite of carbon and graphite (C/Gr) conducting particles suspended in different polymer vehicles were used for preparation resistive layers. Interface resistance Rc created between dipping silver (DiAg) contact layer and resistive layer was determined from the surface potential distribution measurements...
-
Heat Dissipation from the Power Cable in the Casing Pipe
PublicationThe current carrying capacity of a power cable determines its ability to carry a specific current and is related to the efficiency of dissipation of heat generated in the cable laid in a specific environment. The studies were conducted in order to determine how the characteristics of the medium around the cable affected its temperature, and thus the ability of the cable to transmit electricity. The experimentation in the lab and...
-
Chemically reduced graphene oxide based aerogels - Insight on the surface and textural functionalities dependent on handling the synthesis factors
PublicationEfficient adjusting of reduced graphene oxide aerogels properties requires information about experimental factor-aerogel property relationship. In this work, the reduced graphene oxide aerogels surface and textural functionalities in relation to precursor concentration, gelation time and hydrogel freezing temperature were studied in detail, with the use of dynamic adsorption method of gaseous organic probes and experimental design....
-
Transformational leadership for researcher’s innovativeness in the context of tacit knowledge and change adaptability
PublicationThis study explores how a learning culture supported by transformational leadership influences tacit knowledge sharing and change adaptability in higher education and how these relations impact this sector’s internal and external innovativeness. The empirical model was tested on a sample of 368 Polish scientific staff using the structural equation modeling (SEM) method. Then results were expanded by applying OLS regression using...
-
COMPARISON OF TWO MODELS OF CONDENSATION
PublicationIn the low-pressure part of steam turbine, the state path usually crosses the saturation line in penultimate stages. At least last two stages of this part of turbines operate in two –phase region. The liquid phase in this region in mainly created in the process of homogeneous and heterogeneous condensation. Several observations confirm however, that condensation often occurs earlier than it is predicted by theory i.e. before the...
-
A Fail-Safe NVRAM Based Mechanism for Efficient Creation and Recovery of Data Copies in Parallel MPI Applications
PublicationThe paper presents a fail-safe NVRAM based mechanism for creation and recovery of data copies during parallel MPI application runtime. Specifically, we target a cluster environment in which each node has an NVRAM installed in it. Our previously developed extension to the MPI I/O API can take advantage of NVRAM regions in order to provide an NVRAM based cache like mechanism to significantly speed up I/O operations and allow to preload...
-
Comparison of Two Nonlinear Predictive Control Algorithms for Dissolved Oxygen Tracking Problem at WWTP
PublicationThe wastewater treatment plant is classified as a complex system, due to its nonlinear dynamics, large uncertainty of disturbance inputs, multiple time scales in the internal process dynamics, and multivariable structure. The aeration process, in turn, is an important and expensive part of wastewater treatment plant operation. All operating parameters of the aeration in biological processes are to be precisely controlled to provide...
-
Direct-contact condensation from vapour- gas mixture in a spray ejector condenser for negative CO2 power plant
PublicationDirect-contact condensation of vapour containing the inert gas on a spray of subcooled liquid exists in a number of technical applications. For example, it may be found in the nuclear industry (e.g. pressurized jet under normal operating conditions, in safety analyses) or in the chemical industry (e.g. mixing-type heat exchanger, degasser, sea water desalting). The problem is also essential to modelling and analysis of some...
-
A novel concept of H2/O2 steam generator
PublicationThis paper presents an idea of hydrogen utilization to steam generation to drive a turbine and produce electricity or to supply a condenser as an element of a heating system. Electrolysis process is considered as a source of hydrogen as well as oxygen. Hydrogen combustion with a stoichiometric ratio of pure oxygen produces steam at very high temperature. Steam temperature can be controlled by mixing the generated steam with liquid...
-
A NOVEL CONCEPT OF H2/O2 STEAM GENERATOR
PublicationThis paper presents an idea of hydrogen utilization to steam generation to drive a turbine and produce electricity or to supply a condenser as an element of heating system. Electrolysis process is considered as a source of hydrogen as well as oxygen. Hydrogen combustion with a stoichiometric ratio of pure oxygen produces steam at very high temperature. Steam temperature can be controlled by mixing the generated steam with liquid...
-
Evaluation of thermal cracking probability for asphalt concretes with high percentage of RAP
PublicationThe paper presents determination of the probability of thermal cracking of asphalt mixtures with different reclaimed asphalt pavement (RAP) content on the basis of laboratory tests and analytical evaluation using thermal stress development method. Probability was evaluated taking into consideration: the type and gradation of the mixture and the quality and content of RAP. Thermal stresses were determined using two models: elastic and...
-
Crossover from charge density wave stabilized antiferromagnetism to superconductivity in Nd1−xLaxNiC2 compounds
PublicationThe path from the charge density wave antiferromagnet NdNiC2 to the noncentrosymmetric superconductor LaNiC2 is studied by gradual replacement of Nd by La ions. The evolution of physical properties is explored by structural, magnetic, transport, magnetoresistance, and specific heat measurements. With the substitution of La for Nd, the Peierls temperature is gradually suppressed, which falls within the BCS mean-field relation for...
-
The interaction of the pulsed laser irradiation with titania nanotubes - Theoretical studies on the thermal effect
PublicationThis paper reports temperature dispersion simulations of titania nanotubes irradiated by the 355 nm, pulsed, nanosecond laser. The modelling with the use of Finite Elements Method concerns titania nanotubes of the length and the wall thickness in the range of 0.5–2 μm and 5–20 nm, respectively. The uniqueness of the morphology was preserved by ensuring the wall thickness variation along the height of the tube, which was determined...
-
Volumetric and torque efficiency of pumps during start-up in low ambient temperatures
PublicationThe volumetric, torque and total efficiency of hydraulic pumps change during start-up in low ambient temperatures, as well as in thermal shock conditions, un-til they reach the set conditions. The time to reach steady-state conditions de-pends on many parameters: ambient temperature, flow rate, fluid temperature, design of hydraulic units. The author carried out tests of hydraulic pumps in the Hydraulics Laboratory of the Faculty...
-
Synthesis, thermal, structural and electrical properties of vanadium-doped lithium-manganese-borate glass and nanocomposites
PublicationA glassy sample with a nominal formula LiMn1−3x/2VxBO3 (where x = 0.05) was synthesised using the melt-quenching method. Material was characterised by differential thermal analysis (DTA), X-ray diffactometry (XRD) at room temperature and as a function of temperature (HT-XRD), X-ray photoelectron spectroscopy (XPS), impedance spectroscopy (IS) and scanning electron microscopy (SEM). Dependences of glass transition and crystallisation...
-
Phase change thermal energy storage – the experience of the materials preparation for the specific applications.
PublicationThermal energy storage and temperature stabilization is very important in many engineering applications. There are three kinds of thermal energy storage: sensible heat, latent heat and reversible chemical reaction heat. Phase change materials (PCM) absorb, store and release large amounts of energy in the form of latent heat, at constant temperature, called the transition temperature. Many innovative applications could be found...
-
Solvation of ionic liquids based on N-alkyl-N-methylmorpholinium cations in N,N-dimethylformamide and dimethyl sulfoxide – A volumetric and acoustic study
PublicationApparent molar volumes and molar isentropic compressibilities for N-ethyl-N-methylmorpholinium and N-decyl-N-methylmorpholinium tetrafluoroborates in N,N-dimethylformamide (DMF) and dimethyl sulfoxide (DMSO) have been determined from density and speed of sound measurements over the temperature range T = (298.15, 303.15, 308.15, 313.15, 318.15 and 328.15) K at experimental pressure p = 0.1 MPa. This data has been used to calculate...
-
Improved maximum power point tracking algorithms by using numerical analysis techniques for photovoltaic systems
PublicationSolar photovoltaic (PV) panels generate optimal electricity when operating at the maximum power point (MPP). This study introduces a novel MPP tracking algorithm that leverages the numerical prowess of the predictor-corrector method, tailored to accommodate voltage and current fluctuations in PV panels resulting from variable environmental factors like solar irradiation and temperature. This paper delves into the intricate dynamics...
-
Synthesis, microstructure and electrical properties of nanocrystalline calcium doped lanthanum orthoniobate
PublicationThe single phase lanthanum orthoniobate with tetragonal structure has been synthesized by the means of mechanosynthesis method. The studies have shown the crystal structure of La0.98Ca0.02NbO4 depends on the synthesis stage. The samples were predominantly in the tetragonal phase with a trace amount of the monoclinic phase. The SEM studies of morphology and microstructure have shown nanocrystallinity of the materials. The Raman...
-
The Laboratory Stand for the Evaluation of Heat Dissipation from the Power Cable in a Casing Pipe
PublicationThe current carrying capacity of a power cable determines its efficiency, which depends on its capability to dissipate heat produced inside the cable, as a result of current flow, into the surrounding. The studies were conducted to determine how the characteristics of the medium around the cable affected its temperature and, as a result, its ability to transport electricity. The experimentation in the lab and real measurements...
-
Szacowanie estymaty menzurandu temperatury skóry człowieka podczas próby wysiłkowej
PublicationW artykule zaprezentowano wyniki pomiarów temperatury skóry człowieka podczas próby wysiłkowej. Ponieważ uzyskane wyniki nie podlegają rozkładowi normalnemu, wyznaczono wartości pięciu różnych estymatorów menzurandu. Otrzymane rezultaty wykazały, że w rozważanym przypadku najlepszy estymator menzurandu otrzymujemy z metody bootstrap, ponieważ charakteryzuje się on najmniejszym odchyleniem standardowym.
-
Wpływ wprowadzenia norm europejskich na konstrukcję wsporczych napowietrznych linii elektroenergetycznych
PublicationKonstrukcje wsporcze linii elektroenergetycznych były i są projektowane zgodnie ze specjalistycznymi normami, innymi niż stosowane w budownictwie. Dotyczą one zarówno oddziaływań środowiskowych, takich jak temperatura, wiatr, oblodzenie i oddziaływania stałe (naciąg, przewodów, osprzęt), jak i zasad wymiarowania. W artykule przedstawiono wyniki analiz porównawczych dotyczących wpływu zmian wprowadzanych w normach europejskich na...
-
Przygotowanie przemysłowego obiektu o stalowej konstrukcji nośnej do remontu po pożarze
PublicationW artykule przedstawiono warunki i sposób podejścia do naprawy stalowej konstrukcji nośnej kilkukondygnacyjnego obiektu przemysłowego, który uległ uszkodzeniu w wyniku oddziaływania wysokiej temperatury pożaru. Omówiono rodzaje badań i sprawdzeń oraz sposób przeprowadzenia kontroli konstrukcji, które stały się podstawą do wydania oceny technicznej o możliwości odbudowy i remontu obiektu, bez jego nadmiernej rozbiórki. Wskazany...
-
Application of Headspace Solid-phase Microextraction with Poly(1-vinyl-3- Hexylimidazolium Chloride) Polymeric Ionic Liquid Coating using GC - MS to Determine Volatile Fatty Acids in Dairy Wastewater
PublicationVolatile fatty acids were determined in this study using headspace solid-phase microextraction (HS-SPME) with a poly(1-vinyl-3-hexylimidazolium chloride) polymeric ionic liquid coated fiber followed by gas chromatography - mass spectrometry. Experimental parameters such as extraction time and temperature, sample volume as well as desorption time and temperature were optimized. Detection limits of the method were in the range of...